I would like to know can we configure vlans with cisco 1721 Modular Router? Is it Possible to configure lan environment with the vlans configured in 1721 router without a managed switch?
View 9 RepliesIs it possible to cisco 1941 security bundle router Support minimum of 2k of VLANs ID and shall support upto 60 vlans?
View 4 Replies View RelatedSecond laptop attached to cisco 10mb port with an IP address of 10.18.158.200 and the cisco interface 10.18.158.254.Okay, here is what is happening and I cannot work it out.If I ping, from Laptop 1 to the cisco subinterface on 192.168.94.253 it is succesful. If I ping from the 1721 to Laptop 1 it is successful. I see the VPN come up and the rulebase on the junipers show the traffic flowing across (ICMP).If I ping, from the 10.18.158.254 interface via telnet on the 1721, I can ping all the way through to 192.168.194.254, which is the gateway for Laptop 1.
View 1 Replies View RelatedCoincidentally when i tried to configure router 877 as an adsl router i found that a vlan configuration is included. my question is what is the benefit of using vlans in router ??? i studied that we use it in switches for the purpose of network enhancment from broadcasts and netwrok segmentation. why we use vlans in routers ?
View 9 Replies View RelatedDoes Catalyst 3550 switch support inter vlan routing ?
View 12 Replies View RelatedCan nexus 5010 supports inter v lan routing , as there is no core switch and router available in current network.
View 2 Replies View RelatedCisco 6509 modular IOS getting high cpu in interrupt but the switch process switching is still less. Any sugeestion what could be the problem?
Process sbin/ios-base, type IOS, PID = 16407CPU utilization for five seconds: 12%/81%;
Sometimes cpu goes upto 100%
Version - s72033-ipservicesk9_wan-vz.122-33.SXH5
We bough an Cisco 2911 router, and as i see the "ip sla monitor" command is not supported. Which license/IOS upgrade should i buy the fullfill this. And i cant add a trunkport to the iunterface even cant add a vlan to interface. How do i a trunkport on the cisco 2911 router. ANd how can i do a vlan on a interface on the router.
View 2 Replies View RelatedLong time since I have had to configure a router and have a small project
Here is what I have in a simple diagram:
PC(static IP)--to--Switch--to--(Ethernet0 int, WIC0)1721 router(FastEthernet0 int, built-in)--to--Switch--to--PC(DHCP)
I need static IP PC to be able to ping the DHCP client. Static IP units 10.1.1.x/16, DHCP clients 10.1.3.x/16.
I have found these overlap and thus give errors and will even shutdown the interface if I enable certain things like routing or bridging.
So I gather I need to change one interface IP range, which would be the DHCP side, I need to stay 10.1.1.x/16 for static side.
enable dot1q encapsulation on two ethernet ports on a 1721 router. I am able to configure it on the built in fastethernet port, but not on any interface provided by a WIC-1ENET or a WIC-4ESW. I have an application that requires two physical ethernet ports that support dot1q encapsulation.
View 4 Replies View RelatedTrying to work out if I can setup a VLAN interface on a 1721 router.The only interfaces that are listed are the Ethernet (W1-ENET) and the Fast Ethernet interface.I'm still super new to all of this and learn how to change IOS via rommon and TFTP after realizing I had an IOS too large for the memory?
View 3 Replies View RelatedWe're going to be switching some of our gear from Foundry to Cisco, and were looking at the WS-C2960S-48TS-L. We currently have 3 different VLAN's, and I wanted to have 1 uplink back to our firewall (ASA 5550) and then let the firewall do the routing between the subnets. I realize that 1 link will carry the traffic twice then, but is that possibly with those switches to have all three vlans assigned to one port and then just let the firewall do the routing between the vlans or would I need to have 3 uplink ports back to the 5550?
View 1 Replies View RelatedI am working on a backup system for my WAN. Verizon quoted the HWIC-3G-CDMA-V to work with my Cisco 1721 router. I have a bunch on these routers on a shelf and thought I would use them for the 3G network. Looking at the Cisco web site it does not list the 1721 as being able to work with this HWIC. I thought it might not be listed as the 1700 series are End of life. Whether it will work?
View 3 Replies View RelatedI am using a bunch of Cisco 1721 routers for my T1 lines. We recently purchased Digi cell modems as a backup for the T1. On configuring vrrp to work on both devices I discovered that IOS 12.3(6c) does not support the "vrrp track" feature. After reviewing the Cisco Feature Navigator I could not see an IOS that will support the vrrp object tracking. Is that correct? The routers have T1 WIC's installed. If it does work what is the latest IOS that will work on this end of life product?
View 1 Replies View Relatedhow can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View Relatedrouter 1721 with one wic-1adsl ,i have adsl conection with irb static ip. the router connect with mannaged switch through a trunk port. the switch has 2 vlans one for the static IPs and the other for private lan. i need the private lan to be able to go to internet. vlan2 can go to internet because it has the same subnet with provider but vlan 1 canot go internet, so how i can make all vlans go internet(the router has only 1 fastethernet port)
View 4 Replies View RelatedI have a 1721 router installed with both an adsl wic and a 4 port switch wic card. My setup is as follows:
pc connected to port 3 (mode access on vlan 20) on the 4 port switch wic (installed in 1721 router)port 4 is configured as trunk (encap dot1q) and connected to fasethernet 0 (inbuild of 1721)fastethernet 0 configured with no ip address?
created sub-interface fastethernet 0.20 with encapsulation dot1q on vlan 20?ip address of sub interface 0.20 is 192.168.20.240?pc nic ip address is 192.168.20.245 however cannot ping 20.240?I want to use only this router with its switch wic for vlans and internet?
I started to set up a 1721 router with WIC-4ESW. This is on an internal network, so only looking to just do routing from FA/0's interface to the networks attached to ports on the WIC. I first assigned just VLANs to 2 of the ports and this did not work. So I did some reading up and decided to use bridge groups. Except I still can not access the interfaces on the WIC. And by that I mean on the router itself I can not ping the ip assigned to the BVI.
I have another 1721 w/4 port that long ago I seem to remember simply assigning VLANs to the interfaces and I was able to communicate between the networks without issue (or maybe I just don't rememer that well). Thing is I should be able to at least ping the internal interfaces shouldn't I (assuming the status is up). I don't know why BVI2 and 3 are listed as down, nor do I seem to know how to bring these up.
This is what ip int br gives me:
1721#sh ip int br
Interface IP-Address OK? Method Status Protocol
BVI2 192.168.101.1 YES manual down down
[Code]....
I have set up a couple of vlans on a cisco 1721 router 4esw card using the vlan database and assigning an ip address of 192.168.1.x and 192.168.2.x for each vlan interface.Strangely enough connected computers can talk to the other vlan and I have not set any subinterfaces on the etherner0 (layer 3) and not even connected a cable.Is there any reason why this should happen since they should not talk to eachother being on seperate vlans.Doing a tracert shows that first the vlan ip address is hit and then straight to the target pc in the other vlan?
View 4 Replies View RelatedI can ping [URL], from the router but not from a client attached to the router dhcp interface(10.1.3.1). When I turn on ip routing I cannot ping at all. Here is the config I have now that can ping the internet from the router.
sh runBuilding configuration... Current configuration : 1191 bytes!! No configuration change since last restart!version 12.3no service timestamps debug uptimeservice timestamps log datetime msecno service password-encryption!hostname
[code]....
I have a Cisco 1721 router with an ADSL wic. I have followed guides on the Cisco website so that I can connect the router to my home adsl connection. The router connects to my broadband provider and sucesfully obtains an IP address along with Dynamically assigned DNS servers. I am able to ping google.co.uk from the router but not from clients attached via DHCP.
I have noticed that if I ping the IP address of google.co.uk from a client it resolves but it will not resolve the name. This would lead me to believe that the problem lies with DNS resolution/forwarding but I do not know how to investigate further.
My company just assumed management of a remote entity. The network has several misconfigurations and I need to make some network modifications from my office w/o losing access or incurring lengthy outage to the clients. The network consists of 1721 router and three 2960 switches.
- I only have access to the router from the Internet. I telnet off the router to the 3 switches.
The site uses a single class C 192.168.1.0 / 24. The router is running RIPv2 even though this is the only network. The prior network person (contractor) set up separate native vlans on each switch and all the ports are defined as Native trunk and access are defined to the VLAN interface assigned to the switch. So of course the logs are flooded with Native VLAN mismatch, Each 2960 switch is a VTP server but has no VTP domain.
basic network layout:
Internet => Eth [Cisco 1721] => Fa 0 192.168.1.254 ==> [SW1]
[SW1]
interface Vlan1
no ip address
no ip route-cache!interface Vlan220ip address 192.168.1.219 255.255.255.0no ip route-cache
[code]....
!interface GigabitEthernet0/1description SW2 Gi0/1switchport access vlan 204switchport trunk native vlan 204!interface GigabitEthernet0/2switchport access vlan 204switchport trunk native vlan 204!interface Vlan1no ip addressno ip route-cache!interface Vlan204ip address 192.168.1.224 255.255.255.0no ip route-cache Normally, I would assign the current 192.168.1.254 to a subinterface to Router Fe 0/0 but with each switch having its own native VLAN I am afraid I will lose connectivity to the downstream switches -- my only access is telnet off the Cisco1721 Router.
How do I submit an RFE (Request For Enhancement) to the Cisco SBR team to encourage them to implement the missing support for VLAN to VLAN firewall rules that was available in the RVS4000 (See [URL]) and that was supposedly added to a beta release of the RV220W firmware (See [URL])?
View 1 Replies View RelatedAny "best practices" or recommendations on how to migrate from a fixed router (3745) to vlan routing on Catalyst 4507 switches in order to minimize the disruption to the network.
View 4 Replies View RelatedI have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies View RelatedI have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
i need to solves this little problem on 2960S lan BASE but i dont know if it is possible.
Uplink port config for gi 1/0/28 is:
switchport mode trunk
switchport trunk alloved vlan 10,11
but on interface gi 1/0/1 i want to have data from vlan 10 tagged as VLAN 20.
At this time i have solved this issue very primitively
I have set up gi 1/0/2 as int mode acces, acces vlan 20 and i have connected gi 1/0/2 with gi 1/0/3 with eth cable. int gi 1/0/3 is switchpor mode acces, switchport acces vlan 10
I would like to know if AIM-VPN/EPII-PLUS (at the moment installed in 2821 ISR) is compatible with 1841 modular router?
View 5 Replies View RelatedI have a 3750G switch in my production network that only has VLAN 1 on it. All ports are in a default state and VLAN 1 is disabled. The switch is passing traffic but shouldn't having the default VLAN shut down cause the ports not to pass traffic? If I start to create VLANs will that cause the switch to stop passing traffic?
View 4 Replies View RelatedI am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
We have a low bandwith (15-20 Mbit/s) to the ASA from our Client vlan. If i connect the Client to the same vlan as the ASA is, the bandwith (90 Mbit/s) is good.
Here are the Layer 3 Design:
Client -> vlan 2 - Switch - vlan 7 -> vlan 1 - ASA 5505 -> ISP
The Layer 2 Design:
Client -> Gig2/0/13 - Switch - Gig4/0/43 -> Eth0/1 ASA5505 -> ISP
IP Address:
Client: 172.16.2.10Vlan2: 172.16.2.1Vlan7: 172.16.7.1ASA: 172.16.7.2
I assuming the switch has a problem with routing ?It is a stacked Switch with following members:
switch 1 provision ws-c3750g-12sswitch 2 provision ws-c3750g-24tsswitch 3 provision ws-c3750g-24tsswitch 4 provision ws-c3750x-48
And we have following error message in the log from the switch:
%PLATFORM_UCAST-4-PREFIX:
One or more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded I first get the idea that the switch is overloaded with router traffic. Thats why i assuming i have to check the sdm templates, but i'm not sure if this resolves the issue.
Here are the relevant config:
ASA Interface on the Switch:
interface GigabitEthernet4/0/43description ASA-inside LANswitchport access vlan 7switchport mode accessspanning-tree portfast
Client Interface on the Switch:
interface GigabitEthernet3/0/1switchport access vlan 2switchport mode accessswitchport port-securityswitchport port-security aging time 2switchport port-security violation restrictswitchport port-security aging type inactivitymacro description cisco-desktopspanning-tree portfastspanning-tree bpduguard enable
[code]...
What is a good replacement for the 28XX / 38XX router that will support ATM/IMA?
View 2 Replies View Related