I'm trying to configure an snmp notification reciever on WCS 7.0, so that critical alarms get reported to our central console. Following the configuration guide I was able to add the reciever as northbound, but after adding it I get an alarm saying that it is unreachable by WCS so all alarm notification will be suspended. I have tested snmp and ping connectivity between the WCS box and the notification reciever and it works ok, is there some other traffic that I might be missing?. I've seen some packets going from the WCS box to TCP port 7 on the reciever, which as far as I know is the echo service, is that what WCS uses to test connectivity?
I have a Class HD 9000x 2USB TV receiver. It comes with a wireless connection. I am not able to connect it to my wireless router. When I try to connect it to the wireless router it says "No Wireless device" Although all other wireless devices (Labtop, Mobile) are working fine. I think there are steps to activate the network connection on the receiver.
Just picked up the Yamaha rx-v867 receiver a few weeks ago. It has an ethernet port so that it can do internet radio (Pandora, etc). Not close enough to the router to go wired. I am getting an old 802.11b router from a family member today. Can I use this as a bridge to send music over the wireless network to the receiver? What steps to successfully setup?
Usually I set up wireless networks with laptops or pc's with wireless cards.
I have a Belkin f5d7234-4 lying around at home. I also have a Panasonic TV which requires a proprietary wifi donge to get a wireless signal, so my question is, can I use the router to recieve my house Wifi (broadcast by my new NetGear Router) and send it out through its Ethernet port to the TV?
I checked, the router doesn't have ddwrt support, I'm new to hacking around with routers and networks, so I don't know how to do this, I see how it is logically possible
I have lost my receiver to a wireless mouse and key board of LOGITECH K260. kindly tell me what should i do to resolve this problem. can i get its replacement from market?
I am getting an alarm on WCS where a one controller is down, unreachable from WCS, while the other one is reachable on the same WiSM module. Upon investigation, Status of controller is shown as "Oper-Up" for all controllers on Supervisory engine. Hardware platform is Cisco 6509-E.
WLAN Slot Controller Service IP Management IP SW Version Status ----+-----------+----------------+----------------+-----------+--------------- 2 1 192.167.10.11 172.19.47.65 6.0.196.0 Oper-Up 2 2 192.167.10.12 172.19.47.66 6.0.196.0 Oper-Up
However, I can not ping the managment interface of the down controller while the other controller management interface is pingable. All these interfaces are in the same VLAN.
ping 172.19.47.65 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 172.19.47.65, timeout is 2 seconds: ..... Success rate is 0 percent (0/5)
Problem is fixed when I reboot the problematic Controller. However, this problem re-appears after some time. I am not able to figure out why controller is not able to ping its default-gateway which is an SVI interface on Supervisory card on the same chassis, and showing status UP/UP. Is it a software bug or backplane fault or any other reason ?
I have 2 brand new systems, a desktop running Windows 7 Pro connected with a had line, and a laptop running Windows 7 Home Premium connected wirelessly. Both can access the router, both can access the internet, both can be pinged from the router. However, they absolutely cannot see each other on the network. If I try to ping by name, the addresses don't resolve. If I try to ping by IP, I get either no reply or the "destination host unreachable."I've disabled firewall completely on both. I've double, triple, quadruple checked all sharing settings (network discovery is enabled on both, sharing enabled everywhere, etc. etc.). I've tried disabling all other network adapters on the laptop, no difference. I've tried all of the online tips about repairing winsock.
I have used this WRT54gl for several years and it's performed flawlessly both wireless and wired. Recently I've extended the reach of my home network by adding a second WRT54g cabled to the network. I also added another PC in a nearby home with a wireless dongle attachment to the network. In setting all this up I've just noticed that the 'Traceroute' and 'Ping' functions in the original WRT54gl do not work. That is, when in the Administration, Diagnostics window and select either function I get a 'Network is unreachable' message instead of the ping/traceroute information.
All other functions on the network seem to work fine, ie..., I can ping the router from anywhere. Both wireless and ethernet connections work fine through it. The newer WRT54G addition to the lan is setup identical and the ping/ trace router work fine with it.Both routers have DHCP disabled. My modem handles it.
Once in a while, I lose Internet connection and at the same time cannot reach my Siemens Speetstream 4100b DSL modem's setup page 192.168.0.1 ; it happened again this morning (from both wired and wirelessy connected computers). When I go to the router's setup page 192.168.1.1 , it would usually in that situation show that the router has not acquired the Internet IP Address; I power-recycle (a few times) both modem and router and eventually the router reports that it has acquired the Internet IP Address, but there is still no Internet, and the DSL modem's setup page 192.168.0.1 is unreacheable.The situation usually self-resolves only in an hour or so after the time the router has acquired the Internet IP Address: Internet starts working, and the DSL modem's setup page 192.168.0.1 becomes reacheable.
I have different types of network clients connecting to both bands of router (5 ghz and 2.4 ghz), and both bands set to WPA2 only. Everything has been set up and working for the past year with no problems.
Suddenly this morning, none of the 2.4 ghz clients can connect and get authenticated. When I attempt to ping them from a Windows 7 desktop connected by a LAN cable, I get Destination Host Unreachable.
The 5 ghz clients are fine and have had no problems. I tested this with the New iPad connected to the 5 ghz band.
Rebooted the E3000 router and the Comcast cable modem, then installed the newest firmware on the E3000 using the web access portal at 192.168.1.1, and still not working.
Changed the WPA2 Personal security mode for the 2.4 ghz band to WPA2 Personal/WPA Mixed Mode, and now all the clients are connected and authenticated and working OK, albeit slower.
What happened? And how can I fix this so I can change the security mode for the 2.4 ghz band back to WPA2 Personal?
P.S. The types of clients that connect to the 2.4 ghz band are 2 Windows 7 desktops, a Windows 7 laptop, and 5 Cisco Wireless N Internet Home Monitoring Cameras. The camera feeds have slowed down considerably using this Mixed mode.
I've tried everything that has been posted so far except for opening up the router itself which I will refuse to do.- Getting = Host Unreachable 192.168.1.20 (I am using 192.168.1.1 as the gateway)- No ping whatsoever even when turning on the router over and over.
We have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings. One went south on us & we placed it. Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP. Now, we can't connect or even ping either AP. And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them. I'm attaching the configuration. Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?
I attempted to upgrade the firmware on the WRT54G2 V1 (the newer, slim black model) but it failed. I let the upgrade run for about 10 minutes and it just sat there and link to router disconnected I run ping for 192.168.1.1 but response is "DESTINATION HOST UNREACHABLE". The router is now completely unusable and the ALL LAN ports lights are ON and Internet light is also ON.
I have not used the ACS5.1 yet so watch out for the easy questions
1) Is it possible to generate report for the users who are inactive for say last 30 days? Customer is looking to audit these users to see if they really need access to any device.
2) Are there any known issues while assigning the priviligaes level to users. In current implementation of this customer users are always logged into priv 1 though they are assigning the priv level of 5. I understand with ACS 4.x we can enable the exec process and assign the priv under user/group policy. What are the configurations that customer might be possiby missing in this case?
3) Is there any SNMP or other notification available in ACS 5.1 where admin can be notified at the time a particulat set of user logs in.
I want to configure E-mail fault notification in LMS 4.0. So Where i will configure E-mail settings like username, password, mail server IP address in LMS. We are using e-mail service hosted in gmail. Through this mail service ca we able to use email notification.?
Have a setup for Cisco LMS3.2.1 which is a recent upgrade, also RME 4.3.2 and CM 5.2.2. Is it possible for the DFM to generate alerts such as email notification to user defined group (subnet grouped). These alerts should be critical in in nature.
I'm needing to be able to send e-mail nofigication when one of our network devices isn't able to be access. I have looked at the DFM configuration but I'm a little confused to how to set this up so that we don't get inundated with to many e-mails.
I recently linked my dtv receiver to the internet through my laptop. My question is, since I'm now sharing the connection, do I need to make any adjustments in the "network and sharing center" to keep sensitive info on my laptop safe?I do have Norton Internet Security.
Just updated my DTV to a HD receiver which has the ability to access movies/shows via internet so I hard wired my belkin router to the TV receiver and I can't get it to connect. The router light does not go on showing me I am not connecting to the TV receiver. When I go into the DTV receiver it reads all my IP address and has an OK behind them, but says there is an error and the internet is not connected. When I plug the same cable into my PC or my laptop the light on the router does come on. Also my iphone does receive WIFI via the same router. I called DTV and they said everything on the receiver is correct. I called my router folks and they said everything is correct and that it must be the DTV receiver. I've been using this router for several years and their tech guy sounded like he knew what he was doing. how I can get the router to recognize the TV receiver?
Here are my router settings: I used the WAN IP info in my TV receiver. Home| Help| Logout Internet Status: Connected LAN SetupLAN SettingsDHCP Client ListInternet WANConnection TypeDNSMAC AddressWirelessChannel and SSIDSecurityUse as Access PointWireless BridgeFirewallVirtual ServersClient IP FiltersMAC Address FilteringDMZWAN Ping BlockingSecurity LogUtilitiesParental ControlRestart
I need a vpn address for Digital satellite receiver TITANIUM HD 20000.I have tested several address which are working on my pc windows but my satellite receiver can not connect to vpn server. what should i do?
A 2 Wire 2701HG-B DSL MODEM/Router Upstairs Wired into 2 PCs upstairs WiFi to a PC Downstairs.
I killed the DSL service and got U-verse, but that added a new Modem/WiFi downstairs. I still have the 2Wire upstairs, but it has no phone connection.Can I use the 2Wire to "Receive" and "distribute" the WiFi signal from downstairs?
I don't see how to turn off the DSL MODEM. If I put in the ID and Password for the WiFi router downstairs into the 2Wire upstairs, will it "Login" or will it conflict? Are there special settings for the PCs to access the U-Verse router through the 2Wire?Basically, I want to know if the upstairs 2Wire can receive the U-verse signal and convert it to wired signal for the 2 upstairs PCs.
I am trying to setup Fault Monitoring on LMS 4.0. When I try to create a Fault Notification Group no devices are listed. They appear to be listed in all other places so I am at a loss as to explain why they are not appearing.
Has any one got a working setup for SSL VPN users in regards to notification about password is going to expire and then providing the VPN user the opportunity to change password during the VPN login process, involving ASA5520 - ACS Radius server - Active Directory Our VPN users are connecting with Cisco Any Connect VPN Client V.2.5.3046 to a ASA5520 running 8.4(1), all user validation is handled via Radius though a Cisco ACS 5.2 server, which in turn validates the users up against MS Active Directory.
For the relevant connection profile on the ASA, the options Advanced / General/ Password Management / Enable password management has been selected together with the Notify user 14 days prior to password expiration, as mentioned its connecting to a Cisco ACS Radius server with MSCHAPv2 enabled on both the ASA and ACS.
On the ACS server under users and Identity Stores > External Identity Stores > Active Directory we have a successful bind to the AD, the values End User Authentication Settings > Enable password change has been selected.
Just to make sure the password notification function is working in the first place I change the ASA5520 AAA Server group to use LDAP instead of Radius and configured a direct path towards one of our domain controllers, sure enough when the user logged in he got a notification about the password would expire in xx days and then provided with a option to change the password right away or just connect with the current password.
The thing is I don’t want to just use LDAP for VPN authentication, I have quite a expensive setup on the ACS servers with unique ACL's for various group of employees and especially for external consultants, I also use the ACS for customization for webpage and resources when Web VPN is used.
Can it really be so that password expiration notification only works using LDAP, and if this is really the case, is there any way to configure Dual Authentication, so I could first validate the user against LDAP and next against the ACS??
(Side note: I tried to configure the ASA to use LDAP as normal Authentication and then the ACS as Authorization, but it failed, first off because the ASA started to use PAP/ASCII against the ACS and even if I allowed that, it seemed like the ASA wasn’t parsing the users password onwards, with the result that ACS failed and the user account ended up getting locked out in the AD).
Is it possible to have email notification when a rule is hit on the ACS(5.1)?
Ive had a look around and cannot see any options, the server team seem to think its not possible to have this triggered from AD either on a side note, where are the SMTP settings on the ACS?
I'm in the process of reconfiguring our DFM module have some significant network changes. I've reinitialized the modules databases and manually imported a test group of routers into DFMs device management. The devices have been found and have a known status in the device summary.When I begin the process to create a notification group for email based notifications, the notification group selection window shows no devices available. If I manually search for the devices, I am able to find them, but after selecting them, I'm given the following error:"The devices contaminated in the subscription are no longer found in the inventory"I've confirmed the devices existence in CS and RME.
We have the RVS4000 and have IPS turned on. How can I be notified (email would work) when updates to the IPS signatures are available, so I can keep our IPS signatures current?
