Home Networking: I would like to add an 802.11n wireless router to an existing Verizon FiOS modem/router. I've read numerous How To articles, but frankly am still uncertain of the best approach. Also, as an aside, would you recommend a single or dual band wireless router? I will have one laptop with a special Centrino Wireless LAN card (3x3).
View 3 Replieson my home network I currently only run an Airlink101 AR675W router. We have a couple issues with this. The router for one is in my basement and there are points in my house that have low signal strength, especially upstairs in the far corners of the home. Second is I am currently running my home PC as a media center but it is set-up wirlessly so streaming is clunky and jittery. Also on this network is 3 X-box's wired, a PS3 running wirless, 2 PC's wired in, 2 wirless laptops and the afore mentioned wirless PC. A lot of weight for the network. What I want to do is move the router upstairs, hardwire it into my wireless PC (the one doing the streaming) and connect a second router (an identical make and model I am buying this weekend) downstairs which will be basically used as an "expansion" of the wirless and a switch for the hardwired devices downstairs. would this be better than simply moving the wirless router upstairs (hardwiring my PC) and putting a 5 or 8 port switch in downstairs for the X-box's and 2 wired PC's there?
View 2 Replies View RelatedI`m trying to set up a relative`s Internet up so that it is wireless; currently the router takes signal from cable, not phone, is wired only, and has just one ethernet port. I know the number of ports can easily be expanded using a switch, but is it possible to buy a piece of hardware which could be plugged into the router to broadcast a wireless signal as well? I have looked quite thoroughly for anything that could do this but I`m pretty new to networking
View 7 Replies View RelatedI have a home network with an older desktop, two laptops, couple of PDA and now a cellphone. I'm using using a WRT 110 router I bought new a couple of years ago. It run flawlessly even when I switch from DSL to Comcast Internet.My printer (HP All-in-one) is currently attached to the rear of my desktop and if I want to print anything I have to fire up the desktop. Can I plug the printer in the WRT 110? Be able to print form my laptops?
View 4 Replies View RelatedShopping for a new home router/firewall. Trying to decide between a Cisco ASA 5505 or a juniper equivalent. What are everyone's thoughts?
View 16 Replies View RelatedI have a home networking linksys wireless router and want to add my iBook laptop to this network thru the macs airport . I pcs are xp and vista. iBook is mac os
View 1 Replies View RelatedMy home network consists of a Linksys WRT54GL router running DD-WRT supplying wired access to my desktop, a bridge to another WRT54GL (also running DD-WRT) to provide a wired connection to a XBOX upstairs, and wireless access to about 5 or 6 different devices including several laptops, an iPad, and an iPod touch. My question is this:
I am adding a 22" TV into my office so I can watch TV while working on my desktop. I only have one cable jack in my office which is currently plugged straight into my cable modem. This means I'll have to use a splitter to give both my TV and modem cable access. How much signal degradation or speed do I stand to lose or should expect to lose?
Today I set up a home network:Cable router plugged in to......Homeplug network, (D-Link DHP-307AV/B 200 MBPS PowerLine Homeplugs) plugged in to a LAN port of......a spare adsl router configured as per here: Connecting Additional Routers | Tech Support Forum...with two desktop machines plugged into the LAN ports of the ADSL router.Both of the desktops have got similar specs, are equi-distant from the ADSL router, and are both connected using Ethernet, not wireless.One of them gets a 9MB/sec ADSL [URL]download, the other can't even bring the webpage up and times out if you ask Google to do a search.Taking out the adsl router and plugging the desktop straight into the homeplug gets a network speed of ~13MB/sec on [URL].Plugging a computer directly into the cable modem gives network speeds of ~40MB/sec on [URL] How can I improve on this, and have it so that both machines can access the Interwebnet at a decent bandwidth?
View 8 Replies View RelatedBoth computers run xp. Desktop is had wired to router, laptop is wireless.If router is password protected, is the work group I created safe as well?
View 3 Replies View RelatedAfter trying most things and spending money like water, I still cannot get our home network to be adequate and I am out of options - Tried using two 100MBit/s Netgear routers "bouncing" signal to each other (Wireless Repeating Function). Not ideal as security is small and speed was slow (<10MBit/s) but at least it worked. However these routers had to get pensioned off when we put gigabit ethernet in the office - and the Netgear replacements (a) still have the security limitations with wireless repeating, (b) anyway see to do a worse job of repeating. Tried buying Netgear directional high-gain antennas and directing the signal point to point to a second router - didn't work at all. Tried Powerline (this was in 2008). It sort-of worked but was unreliable and dog slow. I think this is probably not worked by the fact that this building is OLD, most of the wiring is OLD, and anyway the electrical path would take the signal from the 4th floor, down some very old wiring to the ground floor, across a very old switchboard, and back up to the second floor... it's not quite the same as a modern house with modern wiring. Most recently tried using Netgear's Wireless Network Extender. Again, it sort of works, but it's NOT fast at all. In addition there are times when some of our computers using the extension segment of the network are unable to connect - they can still see 3-4 bars of signal, but they cannot get on the network. Appears to be an issue relating to gateway, or DNS, not sure. But I would say about 1 day in 3, when I come home, my wife tells me that the "internet is off".
View 4 Replies View RelatedCurrently, I have 2 Apple Airport Extremes, and 1 Wireless Netgear ADSL Router. The 2 AAEs are connected separately to the router, and this allows us to get coverage in most part of the house (it's a large house with concrete and granite walls). I also have a HP Officejet 8500 'wireless printer' that is wired to the router as you can only print to the printer when it's in standby with a physical connection to the router (that's a different story). So my goal is to replace everything as the router is slowly dying and as a result of this, I want to be able to access the Internet wirelessly throughout the house, and be able to print from any where in the house without anything connected via cables. And as a bonus, I would like the Internet to be accessible 100 yards/metres down the garden (workshop is there). Basically, blanket coverage!
View 3 Replies View RelatedI would like to set up a WAP at home so that we can choose when different members of the family have wifi access.I am currently using ethernet and a Thomson Speedtouch 546(i) V6 router. We have 3 laptop PCs and an imac, also a PS3 and Wii
View 4 Replies View RelatedI've recently changed my DSL connection to HSPA because of low speed of DSL connection (2000).
Anyway, I need to build up 5 Ghz networking at home but there is no dual band HSPA modem router on the market. I need a router which supports DLNA/UPnP for NAS Server. So, I have couple of solutions...
1- I can purchase dual-band Asus RT-N66U and use HSPA/UMTS stick to use this router as main router. I can do this because RT-N66U supports sticks via USB.
2- I can connect my HSPA modem to a dual-band router via LAN and by changing IP adresses I can use dual-band router again as a main modem router. This can be no problem via WAN but my modem has no WAN connection. Is this possible via LAN?
Or do you have any other solution how I can get my 5 Ghz netwroking at home using HSPA connection.
I am purchasing an older home and I am going to have to rewire the networking to the house. I have decided that I am going to push forward with Fiber Optics as my main networking vehicle. As a side I am going to run COAX and Cat-6 along the same cabling routing. The Ethernet and Coax are fairly straight forward, as long as I don't go over 100meter's Cat-6 will do just fine, and can be terminated to a traditional router. The Coax will be to a splitter for television purposes only. Now the difficult and hard to find information on: My plan for the fiber is to run a zipcord Single Mode fiber line to each room of the home. I am using Single Mode Fiber because it has the highest bandwidth for future applications. These runs will be homerun back to a distribution box next to the other comms where it will plugged into a Fiber Optic Switch to network the rooms together. I am going to run 3 lines to my basement (for a home server, office, and HTPC for the basement theatre.), One line to each of the following rooms: Kitchen, Living Room, and Bedrooms. I have bought off the internet the following: 1000ft of SM Zipcord fiber ($199), 4 Fiber Optic Nic's with PCI-Express 1 connections (for $20 a piece, they only run at about 2GB/s, but I can upgrade these in the future as price comes done), 1 16-port 10GB Fiber Optic Switch with trancievers ($140), Terminals and tools: $300.
I have is about connecting my Home Fiber to the internet. I am going to start running Verizon Fios, and that is not a true fiber optic solution because they run a Fiber to their Media Converter and then Coax from there into the house, but I have talked to them and they said they can run the fiber cable into the home. I am wanting to connect that cable straight to my Fiber Optic Switch which would then be connected directly to my computers, as well as a fiber optic wireless router, and then from my switch to their ONT for tv and phone. My question is will this work? What kind of problems will I run into, and what other hardware do I need to get this up and running. I basically do not want to run copper to any of my devices..I either want them to network wirelessly or with a fiber line. (even the wireless will be running fiber since will connect directly to the fiber line via the fiber switch.)So it is expensive, but I believe it is worth it. 200ft of Cat-7 copper costs $199 vs 1000ft Fiber at the same price..and the fact that Cat-7 does have a life-limit on it's bandwidth where as fiber is the future.
I have 2 computers running windows 7 home premium and wireless enabled bluray player. One of the computer is desktop and connected to router by wire. Another is laptop and is wireless.Bluray is wireless.I want to establish a network (sharing among all these 3 devices) so that i can stream media from both of the computers to the bluray. At the mean time it would be great to be able to share files between 2 computer when needed.I checked it on google, it says creating a homegroup. I did but another computer does not give me option to join the group, it also has option to create.
View 6 Replies View RelatedI would like to set up a TV in my spare room which does not have a coax plug. Because of the set of my house running coax cable to this room, although possible, is something I am hoping to avoid. This is because if I was to run the cable on the outside of the wall it would get in my way and it will cost $300 to $400 for a tech to come out and run it through the wall.My first thought was to set up an old computer in my living room and have it connect to a cable box. Then I would send the video signal over the wireless network. The problem is that I cannot change channels on the other end. I have been reading up on power-line networking and it looks like a good option for my problem. I was hoping to find a device that will allow me to plug coax cable into it in the living room send the signal through the power-line to another device in my spare room where my TV receiver would be located. Is there anything like this out there on the market? If not are there any other options I can look at?
View 1 Replies View RelatedI am trying to establish a home network for an HP laptop running Windows 7 wirelessly to a 2wire modem for file sharing with my Vista PC. My laptop recognizes the 2wire network but Vista won't.Do I need to download drivers or adjust any firewall settings?
View 11 Replies View RelatedI've just setup a box with Windows Home Server 2011 RC. It's a AMD X2 with 3GB RAM. Everything is fine with that, but I'm noticing my internal network speeds are pretty slow. I'm seeing on average 0.8MB/s transfer speed between my PC's and the server, and between the PC's themselves. I have everything wired through a Linksys WRT54GS router.Is this as much as I can expect from this setup? It's painful trying to copy media files (music, pictures and HD video) to the server at such slow speeds! What would I need to do to get better speeds? I'm assuming a different router could do better.
View 7 Replies View RelatedI've decided I want to hard wire all my stuff in our family room; however, the modem and router are upstairs in my office. I've got a few options available and wanted to get some opinions from those who have tried any of them. Here are my three options:
1) Install NETGEAR MCAB1001 MoCA Coax-Ethernet Adapter Kits
2) Install Monster PowerNet 300 Power Line Network Modules
3) Run the Ethernet cables through the wall, under carpet, etc.
I'm primarily looking for info about the speed differences, ease of troubleshooting, etc.
I'm setting up a small network (one server, two clients) to create photo sales kiosks at an upcoming outdoor event. I will need internet access for processing credit card payments but there won't be any wi-fi or ethernet internet access on the site so I'll need to utilize my iPhone's 3G connection. I recently installed "MyWi" app which can tether the 3G and even create a personal wi-fi hotspot but unfortunately it only works in ad-hoc mode, not infrastructure.So far, the wired LAN is working great on my three Macbooks, using a Linksys (DD-WRT) router. Also, the wi-fi hotspot is working great to provide internet to all the computers. The problem, of course, is that I can't have both connected at the same time or else everything breaks. I've tried doing an iPhone-USB-Macbook tether and then sharing the connection via ethernet but the internet doesn't get through the router (because I don't have a clue of how to configure the router for this). I've also tried setting my router (DD-WRT) to do a client-bridge of the iPhone ad-hoc wi-fi, but again, it's way over my head and didn't work.
View 2 Replies View RelatedI am working with a friend who has a home office that is not in a location where DSL or Cable is available. His only option for internet is using a hotspot - in this case, the Elevate Hot Spot from AT&T.
He needs to network two computers so that he can enable QuickBooks Pro in multi user mode - i.e., data file shared on Computer A, accessed by Computer B.
I thought at first that perhaps I could just setup a wireless connection for the office network - however, whenever that connection is on, then obviously neither computer can access the hotspot.
Trying to keep this at *minimal* cost.
My best idea is to old school network - i.e., connect the two computers via crossover ethernet. Am I correct that this will work? Seems to me that then both computers *should* still be able to access the hotspot via their wifi, yet also be networked for file sharing.
My questions are:
1.) Is this a correct assessment?
2.) Are there any road blocks I should be thinking about?
3.) Any reason not to do a direct connection (i.e., any reason I should entertain connecting to a switch instead?)
4.) Is there a certain order I should do things?
Modem - (MODulator/DEModulator) This converts your xDSL analog signals into a digital format for use on your home network. A modem can also be part of a Router/Modem combination device.This device typically sits at the very edge of your network at your ISP's demarcation point (the point from where their responsibility for equipment ends).
Router - A router serves to 'route' information from network to network. I.e. A router will route information between the network 192.168.1.0 and 172.16.1.0. Generally your home routers will come as a modem/router/wifi access point package. It will basically route packets of information that are generated on your LAN (Local Area Network) to the internet, and in turn, route packets from the Internet to your LAN devices.
Wifi access point - Obviously provides a wireless Ethernet signal so that you can connect wireless devices to your home network. Typically, the wireless access points you will see will come as a combination of router/modem/wifi point. You can buy extra wireless access points (not wifi routers) and place them strategically throughout your home to increase signal coverage.
Switch - Uses hardware addresses to 'switch' packets through the LAN. Normally a domestic router will have 3 or 4 switch ports built into it. However, switches do come as standalone devices and can be used to increase the breadth and scalability of your home network by using the extra ports they provide to patch in more devices.
Host - A host is basically your PC, iPad, smart phone, laptop that is situated on your home network.
NAS Drive - (Network Attached Storage) Contains storage space that can be used as network a share by connecting it your home network.
NIC - (networt interface card) this is the component that allows your PC/Laptop to be hard wired into your router or switch. It will have an RJ45 jack so that you may connect Category5 and onwards patch leads into it from your router or switch. This talks with your computer's main motherboard and operating system to give you network connectivity.
MBs vs Mbps - MB = Mega Bytes (this measures file size) and Mbps = Mega bits per second (this measure network throughput).
Wireless card/receiver - as above but wirelessly.
Although we have a moderately wired house with cat6 cables runs in many of the rooms that all end in the basement, I am currently having trouble since I cat stream audio and video files from my desktop in the den to the netbook and receiver in the family room. All computers are hooked up by cable.I have tried a friends advice to plug in the exact IP address of the desktop (and vice versa on the netbook) but still the netbook cat find the desktop nor can the desktop find the netbook. I have tried home sharing in Windows 7 to no avail as I have been prompted to initiate a home network both on the netbook and the desktop when I think it is suppose to be initiated on one machine and same home network joined by the other.DSL Modem --> Linksys WRTGL router running Tomato --> switch -->various rooms (cont.)Family room (one of the various rooms) has a Buffalo WZR-HP-G300NH AirStation (with one USB port) --> 1) netbook and 2) Denon AVR receiver (with network capabilities)I have a switch in the den and the desktop and laptop computers can read off each other through folder/drive sharing even with Kaspersky Internet Security running in the background so I'm sure it's not Kaspersky meddling with my network sharing. If both are on the wireless network, the netbook can access the desktop and vice versa.Is it possible for the netbook to read off the desktop based on my current set up? I can't bring the desktop down as we use them in the den and will not have room for it in the family room. I am not inclined to purchase a stand-alone HTPC at the moment if there is a network sharing
View 2 Replies View RelatedI am planning to imlpement an ASA 5505 in my home network and I am wondering if this is a valid configuration. I am wondering if it is necessary to have 3 separate internal subnets or if these can be cabeled together in a more efficient fashion?
I plan to keep the 2 servers (game, e-mail) branched off the ASA directly in a DMZ configuration. The rest of the clients connect through the wireless/wired router.
Any unforseen problems with a setup like this (Modem -> Firewall -> Internal Router)? I have read sites that say I will have to accept an IP via DHCP for the ASA's external interface.
I have a Dlink DIR-655 router for my wired and wireless router for my home network. I have a 100ft cat6 ethernet cable. I pulled it from the router to my home server in my basement.
Does the 100ft cable make a difference or does the fact that it's a cat6 cable make a difference?
When moving similar files at work, it's faster. So I'm trying to find out what's the bottleneck at home. What speeds should I expect for a home network?
I recently installed a very basic version of XP on my old laptop (Gateway MT3707).After hours of searching for the correct drivers, I found them, and installed them. After installing the correct drivers for wireless internet I was able to pull up the list and find my network on it.When double clicking on our wireless network it asks for a network key (also called WEP key or WPA key).Now we have a password for our network, but after an exhausting amount of tries that won't work. I not sure if that is what its looking for. In our apartment we run mac OSX, windows vista, etc., but usually the password for the network is satisfactory. I have never ran into this problem.I hate to be a noob, but I don't know where to go from here.
View 6 Replies View RelatedI have att uverse which is wireless G. I want to add a 2nd router behind it that will have wireless N. I've made the connection. I see it on my list of networks but doesn't allow me to access it.
View 2 Replies View Relatedhow do i add a computer to my wireless router
View 1 Replies View RelatedShe has comcast xfinity with a the SMCD3GNV router which if you ever look it up has the worst wireless signal imaginable and I can second that. I was hoping to not have to touch the SMCD3GNV router and just add on to it by attaching a secondary router as a wap.What I plan to do (which I am sure has been exasterbated in forums but just want clarity) was to disable DHCP on the new n router ( cheaper than official wap) and set ip out of SMCD3GNV router DHCP ip range but in same subnet mask so probably 192.168.1.2. Then connect the SMCD3GNV router to the new router via ethernet and dont use wan port. Is this basically all I have to do? Do I need to change the channels on either devices since their next to eachother? or will them being next to eachother and same channel cause interference? I have read I can call comcast and turn the smcd3gnv into a bridge ( plain modem) but I would rather avoid calling them and see if 2 wireless access points next to eachother is okay.Also, I plan on doing this by going to microcenter.com and getting a router for 24.99 or less with a coupon I have. Is there any on their website that you would recommend for this setup? Also if you could check the wap on their website and see if you think its worth it to get one of those instead if under that price as well. I want to utilize wireless n signal . Also, the xfinity service she has is rated for 50mbps download and cannot remember the upload , I have tested this wired and it does actually achieve this or greater.
View 5 Replies View RelatedI am having my internet connection in my living room as my co ax is not in any other room. (timewarner internet). So since i cant have all servers and all in living room (wired machines), i want to move the whole setup to my lab room. I want to buy a wds supported wireless router in the bedroom and join it to my wifi of the home - the router will then output to the wired machines.
View 4 Replies View RelatedI have an E1000 router and recently moved to a basement apartment where the only internet access comes from a single Ethernet cable running out of a router upstairs. I can connect to that network (it is family) but ideally I would like to connect my router and create a second network so that I can connect my printer and other devices independently of the upstairs network.
View 2 Replies View RelatedMy ISP comes in via phone line to modem then to wireless router.I want to run 200' direct burial line to WAP so that I can access wireless internet at the far point. I have modem and wireless router. what do I need to do the create the distant wireless access?
View 2 Replies View RelatedI purchased a 2nd router to boost my wireless range.in order to set this up, is all I have to do is set router 2 outside the range of the DHCP and turn OFF DHCP on router 2. Then I can successfully connect the two routers and if I am upstairs use router1 and downstairs use router2 wireless signal?What would be the pros/cons of using the same SSID? I know one benefit would be not having to set-up each device to connect to the new network name of router 2, but IDK what problems this could ensue. One immediate problem I can think of is if a device could not connect I wouldn't know which router (router1 or router2) the device was unable to connect to immediately.
View 3 Replies View Related