Linksys Wireless Adapters :: WUSB600N Doesn't Work Properly And Fails To Connect Network
Feb 28, 2011
I have the WUSB600N wireless adapter, and I'm using it with Windows 7 Ultimate 64bit. I'm using the latest driver available, 3.0.10.0. When Windows first starts, the adapter is not working properly and fails to connect to any networks, no matter how long I wait. If I unplug it and plug it back in after Windows is already running, I do not have this issue. This also does not occur when "restarting" the machine; only when turning the machine off and then back on.
View 2 Replies
ADVERTISEMENT
Apr 23, 2011
I purchased two WUSB600N V2 wireless adapters recently and have had nothing but problems on an otherwise stable network where I have iPads, iPhones, Netbooks, media centres, wireless printers, Notebooks and other USB PC-based network devices working without problems.
The WUSB600Ns are connected to desktop PCs, running WIndows XP SP3. I have removed the Linksys Network Management software and use Microsoft's wireless network management software. I am running the latest drivers 1.4.10.0 for the cards. My WAP is a Belkin F5D-8236-4 running in WAP only mode. It is set to 40Mhz Channel 11 primary, Channel 7 secondary. Protected Mode is off, Broadcast SSID is on. I run WPA2-PSK AES for encryption. Note: I've tried all combinations of bandwidth and channel settings. I've run Netstumbler to find clear air channels - 11 seems best.
The issues are:
* seldomly connects at boot automatically without intervention.
* occasionally does not find WAP to connect to.
* sometimes will not connect to WAP - sits at "Acquiring Network Address".
* sometimes will not even get to Acquiring Network Address.
* Will often, once connected, after a while lose connection - the timeframe is inconsistent.
All of my other devices do not have these issues. I've been working on this issue for about a week trying to stabilise, even get a consistent failure pattern, but I'm about to send them both back.These are close to the most frustrating devices I've configured and I've got a lot of stuff on my network.
View 5 Replies
View Related
Mar 17, 2011
I am using the USB network adaptor, Model : WUSB600N version 2. It has worked fine whenever I have needed it. Except now. I received “Your adapter may not be installed properly”” ERROR 211: The network adapter is not installed properly” message last night. Also the Windows pop-up message: “USB device not recognized” message. I removed the adaptor and reinstalled it into another USB port. The same thing happened. I moved it again to a third USB port, I received the same error on all five of my PC’s USB ports. I was not able to access the network at all last night.
I brought in laptop into work today , because the antenna/extension is kept there. I inserted the adaptor and it started right up. After an hour of usage, I disconnected the antenna and the adaptor and reinserting the adaptor without the antenna directly into the USB port. And it still worked fine.I turned the PC off, disconnected everything and went to lunch. When I returned, booted up the PC, and inserted the adaptor and, once again got the error message: “ERROR 211 – The network adapter is not installed properly…. I tried again, this time using the antenna, and it is up and working for now.
View 1 Replies
View Related
Oct 31, 2009
When I resume from sleep, my WUSB600N fails to be recognized. All other USB devices are recognized. Using up to date chipset, and Windows 7 drivers for the WUSB600N. Gigabyte GA-P35-DS4 Rev 2.1.
View 9 Replies
View Related
Dec 7, 2012
It says my security key is incorrect when I know for sure it IS correct. I connect fine on all my other computers using the same key.
View 1 Replies
View Related
Mar 12, 2011
Recently purchased refurb AE1000, it failed to work in Win7(AsusSabertooth I7 system) showing up but never enabling regardless of what I tried. I tested it in an old notebook I have under XP and worked flawlessly. So, I then tested it in XP mode on the I7 and it worked as well. I've used the latest Cisco drivers but no luck under Windows 7. It obviously isn't the hardware?
View 2 Replies
View Related
Jan 18, 2011
I am trying to connect to the internet a second, older tower using the WUSB600N ver 2 adapter, the unfortunate part is that I have lost my CD's that originally came with the adapter. I am on my primary machine right now so I am able to get online. I am wondering if there is a way that I can get the proper drivers or software, put them on a USB drive and then put them on the computer that I am trying to connect?I have already tried this, but I cannot seem to get the steps right or I don't necessarily know what I am doing. I am at the Linksys support Page [URL] and I have tried to do as I mentioned before, but I am sort of just expecting it to GO and its not working. The computer i would like to make the WUSB600N adapter for is running windows XP pro Service Pack 3?
View 1 Replies
View Related
Jun 29, 2012
I can't create a network bridge in windows xp or well i can, but then my wusb600n says it is not connected, it can find networks but it wont connect to them? I tried take out the lan cable and create but with same result, is this normal that this adapter can't handle network bridge? If i make a virtual machine in Virtualbox i can use the internet, but i cant when i create a network bridge connection in windows xp..
View 5 Replies
View Related
May 8, 2011
I have a WUSB600N version 1, with the newest driver (offical 3.0.10.0), my Windows 7 Ultimate installation has the proper regional settings, and within the driver setting the Linksys device has the correct country region (#1, 1-13).However, I am unable to scan and connect to channels higher than 11. as tested with the network manager in windows plus inSSID scanner. My other devices on the same network see the higher channels.
View 4 Replies
View Related
Mar 15, 2011
So my AE1000 adapter doesn't connect to my network after waking my computer up from standby mode. I tried disabling the power management option where it allows you to turn off the device to save power but it still won't automatically connect to my network. I have to manually remove the adapter from the usb port and plug it back it for it to work again. I'm using Windows 7 64 bit,the latest drivers from Cisco's website, and my anti virus program is Microsoft Security Essentials
View 4 Replies
View Related
Jan 29, 2013
The latest driver is version 3.2.7 for Windows 7. I am still on the 3.0.2.0 driver which works fine for me. I just wanted to note that the 3.2.7 driver obtained from Windows Update doesn't work well, drops connections and takes longer to establish a connection. I've tried to update twice and each time I go back to the older driver.Can someone at Linksys examine the performance of this driver?
View 9 Replies
View Related
Mar 26, 2010
I have installed manually drivers for wusb54gc v3, but the wireless manager still write error 211. I do see the adapter in device manager and it's writen than it's working, bat still the manager doesn't work and ican't see any net. OS Win7 32bit.
View 9 Replies
View Related
Nov 23, 2012
it keeps disconnecting and ping breaks all the time.other laptop and phones work fine.and if i go 5-10 meters away from router it gets worse.tried new drivers and bios.even tried to change settings of wireless card still problem is there.
View 5 Replies
View Related
Apr 18, 2012
So, I bought a used WUSB600N Wireless Adapter and am having difficulty installing it. Of course, there was no installation CD to go with it, so I went to the website to download the drivers and updates and still can't get it to install.
View 1 Replies
View Related
Feb 21, 2010
I have been trying to get the WUSB600N v 1 to enable in Win 7 Pro 64 bit for quiet awhile. Been reading all the posts here and elsewhere. Have tried all the drivers I could down load and still no luck. The drivers would install but the adapater would not enable. Read about some of the problems with Kaspersky but I had Zone Alarm installed and it did not have the same problem. So tonight I decided to completely remove Zone Alarm from the system. Once I removed ZA and rebooted the adapter functioned correctly. I am able to enable and connect using the WUSB600N v 1. Reinstalled ZA and 600N is still working correctly. It just would not install correctly with ZA on the system. I had previously tried disabling ZA but it took a complete removal to get it to work, I even tried it in safe mode but no luck. I don't have a clue as to what ZA was doing to block the adapter from working but it did. So if you have any kind of anti-virus or firewall you might try removing it and see it the adapter will work. I am currently using the latest drivers from the Ralink site but they would not work either until I removed ZA.Message Edited by curlysir on 02-22-2010 06:30 PM
View 9 Replies
View Related
Jun 18, 2011
I've been getting lag spikes with the WUSB600N. I am using Windows 7 64bit with service pack 1 installed. I had drivers version 3.0.1.0 installed and upgraded to version 3.0.10.0. After upgrading the problem got so so bad that I can't play online games at all. I tried rolling back drivers to 3.0.1.0 but it won't go back. I already tried reinstalling the drivers a few times and even reinstalled windows.
View 5 Replies
View Related
Jan 11, 2011
I have an problem with VPN connection on notebooks. Sometimes the VPN connection works perfectly, and other times it just doesn't work at all.The Cisco VPN client software is version 5.0.04.0300. Operating system is Windows XP Prof SP2.When the connection fails, the client statistics window shows "Bytes Received: 0".Rebooting the system, has no effect
View 1 Replies
View Related
Jul 24, 2011
I noticed that many times the adaptor is tranmitting after other device transmitted CTS. this is a violation of the 802.11 spec
View 1 Replies
View Related
Mar 9, 2011
wireless N adapter wusb600N and win 7 pro fully upgraded:Ive tried this with multiple adapters and multiple 3g providers/usb modems. When I connect the adapter, after a while, the 3g modem disconnects and turns red, and the modem connection software says it cant find the usb 3g device. It feels like the windows is somehow mixing the adapter, and the 3g modem or somthing. Again this same problem happens with multiple devices. Is there some settting im missing.
View 1 Replies
View Related
Oct 7, 2011
I have a problem with my WUSB600N in that it periodically stalls my PC for about twenty seconds. It happens randomly, but particularly when I am using YouTube or playing online games. The symptoms are basically that the screen and process lock up. Sometimes I can continue to move the mouse for a short period, but usually that stops moving too. If I'm playing music in the background (iTunes usually or YouTube) then the music keeps going after the lockup, again only for a short period. Usually about twenty seconds or so later, the whole things recovers. I've tried Alt-Tab or Ctrl-Alt-Del while locked, but that does nothing until the system recovers, at which point i find myself with the Task Manager window or back in Windows, so clearly the keystroke has hit the system normally.
PC is running Windows 7 64, with Avast antivirus, Zonealarm firewall, Malwarebytes antimalware.Its an E6750 on a P5N32E Deluxe with 2G RAM.The wireless access point is about five metres away in a straight line through an open doorway. Signal strength is generally excellent (4 of 5 bars is almost invariably showing whenever I look).I've tried one site which suggested using the RALink drivers instead, but I could not even get that to recognise and activate the WUSB600N, so I'm back with the current (as of today) Linksys drivers straight off their site (18-Jan-10 3.0.10.0). Adhoc 11n disabled, 11h enable, Multimedia/Gaming disable, Radio on/off enable. I've tried with all enabled, but still happens. So I'm back with default configuration.
View 3 Replies
View Related
Jan 23, 2011
I've had the adapter for a while now, successfully running on XP SP3 with the linksys software. I could see networks, connect to them with WPA security and get an IP address. I recently tried uninstalling the software, then connecting the adapter to install only the drivers and let windows manage it. Since then, I haven't been able to acquire an IP address. It can see the SSID and connect to it, but continually tries to acquire an IP address. I've tried this with different SSIDs at work and home...same result. I've tried uninstalling the driver from device manager, but every time I restart and connect the adapter, windows recognizes the adapter. I probably made matters worse by connecting another adapter to it, in an attempt to work around the problem. That is a USB adapter, WUSB600N. Tried the same thing, but continually tries to acquire an IP address.
View 2 Replies
View Related
Jun 11, 2010
I have a 300mbps Linksys E1000 router. However, with my WUSB600N (v2) adapter connected, even with "Auto 20mhz/40mhz" set as the router's channel width, I'm still only receiving a speed rate of about 130/144mbps.
View 4 Replies
View Related
Feb 26, 2011
After a lot of googling and scavenging of specifications, I've yet to fully understand what is the difference between the AE1000 and the WUSB600N. I need a good wireless adapter to pair with my E3000, so I'd just like to know what the difference is (if there is one) and which one I should go for.
View 1 Replies
View Related
Nov 11, 2009
I've tried to connect the usb adapter with an Acer Aspire 7736ZG, installed with Windows 7 64bit edition. Well, I *can't*.
- I started the CD installation and when prompted, I've connected the USB stick. Well, the stick couldn't be detected, and the installation couldn't continue.
- Then, I used the Windows7 drivers and managed to install the device (device manager, sees the device normally). But, the CD still couldn't continue the installation of extra software.
- Ok, no linksys software - no big deal. I would use the Windosw wireless management program. NO! The card seems not be present, and the only wireless connections I get, is by the onboard 802.11n card of the laptop (don't ask why I bought an extra 802.11n card).
- Nothing happens by disabling the onboard 802.11n card and trying all over again.
- If I go to the connection and sharing center and select "change setting of adapter", well, my expensive and cisco-super-duper card, isn't there, and I can only find the Atheros ARB93 Wireless card and the local (wired) adapter.
So, to sum up, 64bit driver seems to be installed correctly on the device manager (as proposed on other threads) but the adapter is not present on the system. How cool is that?
View 9 Replies
View Related
May 22, 2012
The electric went off in my house about an hour ago, causing my computer to turn off as a result. Ever since, the internet on my PC has been acting up.
My internet was working perfectly before the power cut both on my laptop (my mum was using it at the time) and PC, however, while I've got no problems with the internet on the laptop, my PC keeps losing the connection to a ridiculous degree. It'll drop the connection for over a minute at a time, come back on literally long enough for me to refresh/load 1 webpage (~5 seconds), then go back off again for another minute or two.
All the lights on the router are on and I've even cross-referenced (lacking a better term...) the internet connection between my lap top and desk top and my laptop will work fine when my PC is telling me there's no connection and nothing will load on it. It seems to me that something has happened to my desktop when the power went out but I have no idea where to begin to even try to find out what's wrong.
I've tried turning off the router by both the wall and the little button on the back of it, and I've restarted my PC twice as well and still the internet doesn't work properly. My laptop picked up the connection as soon as the router came back on with no problem but my desktop struggled to find the connection and only picked it up after turning the router off twice aand restarting the computer twice as well and as I said, when it finally did find the connection it just keeps dropping it.
View 3 Replies
View Related
Nov 8, 2009
I am running Windows 7 with the WUSB600N (v.2). Here is how I got it to work.The driver support is not a .exe. You will have to install it yourself...but it's not a big deal.Download the Windows 7 driver for your OS version from the Linksys Support page.Save it to the desktop and then unzip it to the desktop so you can find it easier.Once unzipped you will see 3 folders: Mac, Win7 32 and Win7 64. Choose accordingly.What I did was install it through the "Device Manager". (Right click "My Computer", choose "Manage", then Device Manager",or use the "Search Bar under the Start Menu...whatever. Once you are in the Device Manager...
1. Make sure your WUSB600N is inserted in your computer.
2. Navigate down to "Network Adapters" If you see your WUSB600N adapter...great! Your halfway home!
3. Right click on the "Linksys WUSB600N Adapter.
4. Choose the option to " Update Driver Software"
5. Choose "Browse My Computer for Software"
6. Navigate to the desktop and choose the folder that contains the name of your Windows 7 platform.
7. It should update but, HOLD ON! We are not done yet!!!
In order for it to start transmitting in that shiny new 5GHZ band, you must go into "Network and Sharing Center". Once there, look on the left hand side of the main window and you will see "Change adapter settings"Go there. You should see here that your existing adapter is still working (enabled) and your new Linksys WUSB600N has a big fat red "X" under it (disabled).Right click on your existing adapter and choose, "DISABLE".Then, right click on the WUSB600N adapter and choose "ENABLE".The last thing you should have to do is choose the network you want to connect to (for me it was the 5GHZ one) ..and Viola!!
View 5 Replies
View Related
Feb 3, 2010
I have a PC running Windows XP Home, SP 3. I've got a WUSB600N (old squarish v.1 hardware) attached to this PC via the extender cable and until recently it had been working perfectly.Now, however, something has gone drastically wrong with the setup somehow, because every time I shut down or restart the PC, the adapter refuses to start back up again when the PC is brought back up.The Linksys Network Monitor starts automatically on boot and appears in the systray but the icon is grayed out. If I check the Device Manager listing for the adapter under the system control panel, the adapter is listed there but with a yellow exclamation mark. If I check the properties of the adapter it says "This device cannot start. (Code 10)". If I remove and reinsert the adapter it simply disappears from the list and then reappears, again with the yellow exclamation mark.
If I uninstall the adapter completely (again, through the Device Manager), it uninstalls with no issues. When I reinsert the adapter, it detects it, says "Found new hardware", then after a moment or two says "A problem occurred during hardware installation. Your new hardware may not work properly".
If I uninstall the adapter AND the Linksys Network Monitor software, then reinstall the software and reinsert the adapter, it is properly detected, completes setup and connects successfully to my wireless network. And then stops working again as soon as I reboot the PC.
I'm using the latest driver and software monitor from the Linksys site, the 1.01 version.I'm considering removing the adapter and software and reinstalling JUST the adapter from the drivers, to see if that works. But it's been working fine till now so I'm at a loss to explain what's going on.
View 2 Replies
View Related
Jul 31, 2009
I don't know how to install this driver - I didn't see a .exe file or a "setup" icon
View 9 Replies
View Related
Aug 31, 2009
I bought a v1. wusb600n for win XP sp3, recently for no apparent reason, it became stuck in country region #2 (ch 36 to 64) when i use WZC or even netstumbler to view networks. I have tried uninstall/reinstall of driver, tried using ralink's driver and even another usb600n, but the problem remains.
Checking the INF files shows that all the drivers are trying to install as region #0 (36-64 + 149-165) but they are always showing as region #2
View 9 Replies
View Related
Apr 10, 2011
last night my internet stopped working. I have a Linksys USB Wireless Adapater.Model WUSB600N Ver. 2 I have unplugged and replugged it in numerous times. I have disabled TC IPV6. I have attempted to enter Ipconfig /renew and it said the following
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersXDazX>ipconfig /renew
Windows IP Configuration
[code]....
View 6 Replies
View Related
Sep 5, 2011
I have 1 computer a HP system with Ubuntu 11.04 installation.I would like to install the Linksys WUSB600N-AS (V2) into the Ubuntu but the drivers and instruction is very confusing.tell me which drivers to download and how to install.
View 1 Replies
View Related
Mar 1, 2013
Every time i plug in my adapter wusb600n and i got internet i go play black ops 2 my game and my whole pc freezes and if i do an other internet without the adapter and use a sitecom adapter or an linksys pci card everything works good but with the wusb600n i every time get freezes even when im not in game, my pc freezes every time and it is really good internet speed with this dual band adapter?
View 9 Replies
View Related
Nov 6, 2011
Every now and then my adapter won't be able to connect to the internet for a few minutes, and then it just comes back. This happens frequently, varying from every few minutes to every few hours. If I re-connect the adapter, though, a connection instantly comes back. There's no sign that it's lost connection, the taskbar still displays Internet access and a 5 bars, and the blue light on the adapting keeps flashing; but I just can't connect to the iternet at all.
View 1 Replies
View Related
