I have a home and guest network. I set it up about four months ago. No problem! Two weeks ago it would not connect wireless to the internet. The wired connection is fine but it won't do any wireless networking. I tried to reset the router according to the user guide but that didn't work. The software won't recognize the router now so I don't know what to do now.
View 6 RepliesI have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
View 2 Replies View RelatedFor some reason my new E2000 will not connect to our Charter TV Cable internet service. Another router works fine with same cabling. I have reset EVERYTHING numerous times and cross patched -- hard patched, wireless to where my finers are bleeding. My ISP is DHCP and requires no login. So my router is set to automatically connect. Could the router be defective?
View 1 Replies View RelatedI just need a a way to connect my xbox 360 to the internet. I considered buying a WET610N and was wondering if it will connect to my E2000? I can't use one of microsoft adaptors because something is wrong with my usb ports. Or if it is possible am I able to connect a WET54G? I'm not looking to play online just get connected wirelessly. Will either one of these bridges connect to the E2000?
View 1 Replies View RelatedI have a new Linksys E2000, I was unable to connect one of my laptops to the internet, so I decided to call support with the problem, after 45min and not results, find out that the E2000 do not support the Atheros AR 5007, they told me that I need to get a new driver for my adapter. Fine but Cisco doesn’t have a Driver update for this problem or how to fix it, or at least send you a link where to get the fix.
View 4 Replies View RelatedE2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies View RelatedI have tried to connect Comcast to my new E2000 router, with negative results. I did perform the firmware upgrade on the router (to 1.001). My old Netgear WiFi router works fine, so I know the configuration works.For testing purposes I have the following:
MacBook Pro > E2000
Comcast > E2000
Both via Ethernet cable.
I do have access to the E2000 via web based interface. I have tried a variety of configurations, including the use of the "static" configuration using the current Comcast ip, gateway, subnet and DNS that currently exists. I am unable to get the Auto DHCP to work - Comcast ip's do not appear (in the "status" window.)
I've recently started studying for the CCNA exam and one of the first things you learn is the type of cabling required between devices.Basically, I got curious and checked to find that my pc and e2000 router are connected via a straight-through cable even though it's supposed to be that a router and pc share the same pin layout and should be connected via crossover cable. It's the same story with my xbox and ps3 (also wired directly to the router via straight-throughs).
View 1 Replies View RelatedMy Xbox 360 will not connect to my Cisco E2000 wireless router. It can find the router, but when the Xbox tests the connection it can’t establish a connection with the router. Ironically when I try to use the guest account it can establish a connection with the router before I run in to trouble.
View 1 Replies View RelatedHow do I use Cisco Connect to set up E2000 as a switch and set up wireless connection, when I am using E3000 as my main router that attaches to the modem?. When I use Cisco Connect I seem to only be able to address the E3000 settings through Cisco Connect..
View 3 Replies View RelatedI have an E2000 setup with the Cisco Connect Utility. I have a MAIN account and a GUEST account setup.I'm recently having a problem where I can only connect wireless through the "Guest" account. I can connect to my MAIN account, but it states that I have "Limited Access".
View 9 Replies View RelatedSo, I've been having problems with connecting my HTPC to the E2000. I had an old D-link router + USB Wireless N adapter, but after the Dlink died, I bought the E2000, and upgraded to a faster N Adapter. Anyway, connection had been sketchy using the WPA/WPA2 encryption. I turned it off completely, and did get some better wireless speeds. I couldn't leave it open, though, as there are tons of laptops around my apartment that end up connecting to my network. Connecting wirelessly using that particular adapter continued to give problems. Two blackberries plus a Nookcolor connect with no issues (maybe because they're wireless G, who knows).
I then decided to reset the router by simply pressing and holding the reset button as I've done on all my other routers. It did reset, and reboot, but when it came back on, it would no longer connect to the internet. I've connected directly to my modem, and that works fine, but once I connect to the router...nothing. I did a hard reset (30/30/30), and that cleared everything, it seemed. The HTPC now connects easily, but there is still no internet connection. This is proving to be very frustrating.
Is there something I could have done wrong by doing that very first reset? Is there anyway to configure to get back my internet connection?
I have a Cisco E2000 and I have multiple devises that work but not my xbox 360. I have 2 computers 2 iphone 4s 2 ipods iphone 3gs
They all connect to the internet fine. My Xbox 360 never connected. the xbox can connect to the router. Then the router cannot connect to the internet.
I started the FTP Server at the dlink and forwarded port 80 and port 21 to the ipadress from my NAS, surely i activated it. Port 80 for the webmask Port 21 for the FTP server. If i connected me at my homenetwork and typ in my browser: ftp://"username".dyndns.org the ftp server works, also the webmask from the Sharecenter. If i want to connect me from my work or other pc's, the ftp didn't work. can't ping "username".dyndns.org
View 1 Replies View RelatedI have 300 Mb/s plan from ISP. Then cable connected directly to PC my throughput is as it should be, but then i do connect my PC via E2000 cable connection, it slows down to 200Mb/s. I have tryied also E4200 model and i have same issue.
View 1 Replies View RelatedI have an odd problem where every fortnight to three weeks none of my wifi devices (ipap, laptop, 2x android phones) can connect to my network (Linksys E2000, running firmware 1.0.04 with WPA2 personal). They can all see the network and try and connect, but all fail. Rebooting the router has no effect, and the only thing I've found that works is that I have to connect via ethernet cable (which works no problems) and then disable wireless security, save changes, and then immediately reenable wireless security and save changes again. All my devices then will automatically reconnect no problems. It's a bit annoying as my router isn't ideally placed to dig out the cable, but I wondered if there's any way of diagnosing what could be wrong? I've checked the router logs and they're not useful - the only thing I can see of note is in the DHCP log in the period when I suspect the problem arose I get 4 entries of discover / offer / request / ack going to 255.255.255.255 which seems unusual. But the security log is empty so I get nothing from that.
View 8 Replies View RelatedSo, I've had my Linksys E2000 Router for awhile now (not a year old though), and I just discovered a problem with it.Just the other night, not even 8 hours ago, I was playing my 360, everything was fine. I then decided to go to bed, cause it was getting late. Here I am now, I boot my 360 up, and notice that my 360 couldn't connect to Live. At first I thought maybe the cable got unplugged somehow; nope. So I troubleshooted to fiind out that Ethernet Port one no longer works on my router, but switching the cable to port two, my 360 is able to go online.
Does this mean my beloved router, that I paid my hard earned cash for, has decided to start crapping out on me, or is there a fix for this? I take really good care of all my electronics, and my router sits in a spot by itself on my desk with plenty of air space. I have had no issues with this router in the past, until' now. I've always trusted Cisco, and Linksys products, and this really dissapoints me that my router might just be kicking the bucket, at not even a year old. What's the deal Cisco?
We have been unable to connect our PSPs to the new E2000, and after several hours we're ready to throw in the towel and go get a different router!The PSPs only see the "guest" connection when using the scan option, but cannot connect to it. Even after manually adding both the main and the guest info we are STILL unable to connect either of the PSPs We had an older router from your company which we had no issues connecting 6 desktops, a lappy, 2 psp, 2 ds, 2 xbox 360, and a Wii, as well as our smart phones. After this recent "upgrade" to the E2000 the PSPs CANNOT connect no matter what we do. It gives many different error messages.
View 9 Replies View RelatedI have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
my internet connection cuts in and out so my computer cant connect to the router and it wont show up. I am on a windows 7 toshiba laptop and i have comcast as my internet service provider.
View 1 Replies View RelatedI have an E2000 (2 yrs old) that is not connecting to the internet.It is a slave to a BEFSR81 which controls the DNS.I am able to connect to other computers on my home network, so I know the wirelss is working and the cables are all good. I know that I can plug my laptop into the port on the hard wire router that the wireless was plugged into and I can get internet. So the only thing I can think of is the inernet is being blocked at the E2000.
View 1 Replies View RelatedI can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies View RelatedRunning Win7. When trying to connect Lenovo laptop to E2000 with Easy Setup Key, the progress bar hangs at 25%. However, the E2000 will connect to the laptop with an Ethernet cable. Same problem on both of my Lenovo G555 laptops.
View 4 Replies View RelatedI am unable to get my E2000 router to recognize my Ipad2 when trying to connect.
View 2 Replies View RelatedMy 'main' Wifi SSID will just disappear and you can't connect to it. the guest account will still show up. computers/devices that are already connected will stay connected and will work fine, but anybody reconnecting will not be able to. Only solution I've found so far is to unplug and replug in my router
View 1 Replies View RelatedHow do I add a guest without the cisco connect software since they don't have upgrade for osx lion.
View 3 Replies View RelatedI've just bought an E2000 and I Cisco Connect doesn't run on OSX-Lion, and I was unable to find it on support downloads. But this is only a comment, my concern is that I'm not able to see on main menu how many DHCP clients are connected nor of course to check their traffic. Other routers usually provide at least DHCP clients
View 4 Replies View RelatedI recently bought a E2000 wireless router. After my internet was slow for a few days, I figured out that the router was slowing down my internet.
Here's what happens: When my PC is connected directly to the cable (I am connected to a university network, so no modem), everything is fine and a speed test (url...) shows the speed as 400 Mbps(200 Mbps upload) or more.Once I add the router and connect my PC through the router, the speed test result drops to less than 200 Mbps(100 Mbps for upload). I tried this several times, testing with the same server.At the same time, when I try to open pages, "Sending request"(Chrome) takes for ever! sometimes it stays at "Sending request" for 15 seconds. This happens even google.com, so it's not the Web server.
I have an E2000 Wireless N Router setup to use WPA2/AES. I have Comcast cable internet service and I just upgraded to the 50Mbps speed. I have a Motorola Surfboard modem (DOCSIS 3.0).
If I connect my computer directly to the modem or to one of the ports on the E2000 I get great speeds sometimes up to 60Mbps but on average I am getting 45-48Mbps which is acceptable.
When I try to connect the same computer to the E2000 wirelessly my speed tests return a horrible 18-22Mbps. When I run these tests the computer is in the same room as the router. As I move throughout my house the speed tests are the same. My wireless connection speed to my laptop is good 144Mbps and 300Mbps depending on the band (2.4 or 5.0).
I have tried to use the 2.4ghz and 5.0ghz using different channels. I have also tried different "N Transmission Rate" settings. One of them (5 - 52Mpbs) does increase the speed to around 25-26Mpbs but that is all.
Strangely (or maybe not) the upload speeds are consistent on all of the tests at around 12Mpbs.
I am using Speedtest.net and Speakeasy for all of my tests.
Is there anyway I can get my wireless download speed up to around 40Mpbs? Or am I going to have to run cables through my house to the devices where I need these high speeds?
I also have upgraded to the latest firmware version.(1.0.04)
Internet was working great a few days ago with my e2000 and comcast as my ISP. I've got a few devices connected through ethernet connections on the unit. We also connect to the e2000 wirelessly.Problems started yesterday with no internet. Last night I rebooted everything and still nothing works. Connected laptop to cable modem directly. Wasn't getting internet connectivity so I called Comcast. They reset my modem and everything started working fine. Now I can directly connect from cable modem to laptop and internet works fine. I try connecting the modem to the router and still no internet.
View 2 Replies View RelatedE2000 about a years old.One of the rule is to block internet access from 1am to 4am for certain internal IPs.Working fine until a week ago. Once the time kick in, the E2000 will not route any internet access for any internal IP until the unit is power off and power on reboot.If that rule is disabled. then the E2000 will route all days and nights with no problem.Updated firmware to 1.0.0.4 already.I replaced the WRT45 because of the same problem a year ago. Now just about a year, this E2000 keeps blocking all traffic.
View 1 Replies View RelatedAlright, the computer I had cisco connect on crashed. I got a new computer and I'm trying to install Cisco connect using the downloaded version and I can't install it because it requests the password of the router, which i do not know. This is because I've lost the CD copy of Cisco connect. I've tried resetting the router itself by pressing the red reset button
View 5 Replies View RelatedI simply, can't install Cisco Connect. I want to because it has the parental controls and guest SSID controls. When I try to install, the progress bar get's to 25% and then stops - the next screen says "Our Customer Support team can help. Your router was not successfully setup." I reset the modem and have my computer plugged in to port 1 while I try to install the software. I have been able to setup the router manually. It works great. My issue is that I can't install Cisco Connect desktop software for Mac.
View 9 Replies View Related