Realtek PCIe FE Losing Connectivity In Windows 7 Home 64bit

Mar 23, 2012

I am having an intermittent problem with my network connection dropping out for no apparent reason.When it drops, I still see the lights blinking on the NIC card, but cannot pass packets even to the router.Windows does not report the connection or the cable as disconnected when this problem is occurring.The problem will persist until I disconnect and reconnect the CAT-5e wire, or disable and re-enable the NIC.As soon as I do one of those 2 things, connectivity immediately returns (and works for another hour or so).I am running a legitimate copy of Windows 7 Home Premium 64-bit on an HP Pavilion.All of the latest Windows updates and the latest firmware drivers are installed.My ethernet connection is a wired Local Area Connection with a static IP address, gateway and DNS.The IP address, gateway and DNS settings are accurate and work for several other computers here.The Network Interface Card is a Realtek PCIe FE Family Controller (VEN_10EC / DEV_8136 / REV_05).NIC Power Management, Energy Efficient Ethernet, and Link Down Power Saving are all turned off.On the NIC, ARP/Large Send/IPv4,TCP,UDP Checksum/NS Offload, Flow Control, and are all on.

Receive Buffer Size on the NIC is 64Kb (512 buffers). Receive Side Scaling on. 128 Transmit Buffers.Interrupt Moderation is turned on. Magic Packet features are turned off. Optimal Performance enabled.NIC Speed and Duplex are set to 100mbps Full Duplex wherever possible (automatic was also tried).802.1X authentication (EAP or PEAP) is disabled. Auto connection logic is disabled.Connection routes through two switches into a Belkin router; other devices on same networks unaffected.Much of my data is stored on a Network Attached Storage device, with UNC shares mapped to drive letters.Other Windows, Mac and Linux devices connected to the same NAS device have no problems staying connected.When the issue occurs, I can't ping the gateway, do DNS lookups or pass any packets as far as I can tell.I have tried swapping out the CAT-5e cables for other cables and even ran them through a cable tester.

Network fixes I have attempted from the OS level so far include:

~ Switching the dynamic port range to start at 10,000 and run for approximately 54,000 ports

~ Systematically reviewing every running service to make certain that only the essential ones are on

~ Disabling all NIC stacks except Client for Microsoft Networks, IPv4, File and Printer Sharing and Comodo

~ Attempted connections with Comodo turned completely off and its NIC driver disabled

~ Attempted rolling back the RealTek driver to an earlier one from the same family and device line

Using netsh I have tried the following settings:

~ netsh winsock reset catalog
~ netsh int ipv4 reset reset.log
~ netsh int ipv6 reset reset.log
~ netsh int tcp set global rss=enabled

[code]....

View 2 Replies


ADVERTISEMENT

Realtek PCIe FE Losing Connectivity In Windows 7 Home 64-bit?

Mar 23, 2012

I am having an intermittent problem with my network connection dropping out for no apparent reason.When it drops, I still see the lights blinking on the NIC card, but cannot pass packets even to the router.Windows does not report the connection or the cable as disconnected when this problem is occurring.The problem will persist until I disconnect and reconnect the CAT-5e wire, or disable and re-enable the NIC.As soon as I do one of those 2 things, connectivity immediately returns (and works for another hour or so).I am running a legitimate copy of Windows 7 Home Premium 64-bit on an HP Pavilion.All of the latest Windows updates and the latest firmware drivers are installed.My ethernet connection is a wired Local Area Connection with a static IP address, gateway and DNS.The IP address, gateway and DNS settings are accurate and work for several other computers here.[CODE]

View 1 Replies View Related

Default Gateway Not Available - Realtek PCIe GBE - Windows 7 MSI Mobo

Mar 3, 2012

Currently getting constant disconnects with the following hardware/software

Modem CM100
Router - Tried 4 different routers, issue consistent throughout them all. Original is the Asus RT-n56u.
Realtek PCIe GBE Family Controller
MSI 790XT-G45
Windows 7 Ultimate

After installing several drivers and probably 10-20 tweaks, the issue has stopped for about 50 minutes after consistent at least every 10-20 minutes.I actually just placed an order for a Motorola Surfboard 6121 Although I need the upgrade anyway.

View 1 Replies View Related

Realtek PCIe GBE Family Controller - Can't Connect To Internet

Mar 16, 2012

I can't connect to the internet. I'm currently using a USB internet, but the problem still exists. So it's not working with either cable or USB internet. It just won't connect. I've thought for a long time that there is probably something wrong with my network card, but I've run some tests that I saw on the internet, and it appears as if the network card is fine. I've also thought that there might have been a program or something that I installed that could have caused this problem, but I can't find the problem. When I go to the device manager, I can find one network card called: "Realtek PCIe GBE Family Controller". I've tried to reinstall the card, but it doesn't work. I can't find any software on the internet for this card either.

View 15 Replies View Related

Realtek PCIe GBe Family Controller - Standard Gateway Not Available

Feb 6, 2011

I have just upgraded my computer and now i have a Gigabyte 870A-UD3 mobo with a Realtek PCIe GBe family Controller and i have now gotten the famous "Standard Gateway not available" or something.

View 3 Replies View Related

Cabling / Cards :: Realtek PCIe Freezes The Computer During Torrents

Dec 18, 2012

My computer freezes during torrent downloading , usually within the hour. I have used various torrent clients and problem remains.I have the latest drivers Realtek 8168 v 7065 . Some suggested to turn Checksumms off from the property menu , but that would increase my CPU load. Some other suggested to turn off Task Offload , but I cant find anything similar in Properties.

System Setup
---------------
Summary
Operating System
Microsoft Windows 7 Professional 64-bit SP1
CPU
Intel Core i7 920 @ 2.67GHz55 �C
Bloomfield 45nm Technology
RAM
3,00 GB Triple-Channel DDR3 @ 535MHz (8-8-8-20)
Motherboard

[code]....

View 1 Replies View Related

Realtek PCIe Family Controller - Wireshark Capturing Packets

Dec 18, 2011

Ive just downloaded wireshark just to mess around and ive noticed that even when ive got nothing open its still capturing packets. It gives me a choice of interfaces i want to choose to monitor and i would of thought it be "Realtek PCIe Family Controller" as this is normally the default one (im using wireless) but its saying no packets are being captured from this interface its the "Microsoft" Interface thats capturing the packets. Ive attached a screenshot, i know this isnt nothing bad but was just wondering 1) why isnt my Realtek PCIe interface capturing anything (even when i have youtube open it doesnt capture anything) and 2) why is Microsoft capturing packets? what is this microsoft interface and why is it capturing packets when nothing is open.

View 2 Replies View Related

Error Realtek PCIe FE Family Controller - Unable To Connect To Internet

Feb 7, 2012

so i can not connect to net on my desktop but my wifi works fine, the error is the realtek PCIe FE family controller (code 31) i have tried updating the drivers but nothing i have verizion fios.

View 2 Replies View Related

Home Network With Windows 7 32bit And 64bit?

Dec 20, 2012

Would it work just fine using a desktop with Win 7 64bit hosting the domain for a small home network when there would be 2 dekstops with XP 32bit and a laptop with Win7 32bit?

View 2 Replies View Related

Windows 7 Home Premium 64bit Loses Homegroup?

Jan 28, 2011

It works then it stops seeing the homegroup machines. After struggling with this I have determined some things.

When it stops seeing any homegroup machines, xp, vista 64 and two dlink 323 nas boxes, I can get it working again by restoring the drive with a backup for a time when it did work.

I ran a lan software that showed me mac address, ip address, master brower and workgroup of every machine on the network. I ran the software when the Windows 7 home premium machine didn't see the workgroup. The software showed the windows home premium 64bit machine was not reporting the homegroup name. Looks to me like something is changing causing the win 7 home not to report the workgroup name. I tried changing the workgroup name, rebooting, changing it back then rebooting and it didnt' fix it.

When the machine is not seeing the workgroup I can ping the other machines but I can't map them using their IP addresses. When it lost the workgroup lately I noticed the first sign this time was I could see the machines and directories but could not access them being told I didn't have permissions/access basically. Can't remember the exact wording.

I am at a loss of what to do to fix this and I would perfer a fix verses reinstalling everything from scratch which may or may not perminately fix the problem.

View 5 Replies View Related

Windows 7 64bit - Home Wireless Location Settings?

Jan 14, 2012

Using win7 64 bit 1 pc upstairs and laptop down stairs,no need for file or printer sharing so its disabled. Is it right that the public location setting is the safest setting with the sharing option disabled,and that wpa etc is not used, If you know you won’t need to share files or printers, the safest choice is public network.

View 6 Replies View Related

Linksys Wireless Adapters :: Use WUSB54GC On A Computer With Windows 7 Home Premium 64bit OS?

Mar 2, 2011

I want to use this adapter on a computer with Windows 7 Home Premium 64bit OS.Downloads lists versions V1.0 and V3.0 for this adapter. How can I determine the version I have?V1.0 list no driver for Win 7 64bit. V3.0 list a driver for Win 7 64bit.Research I found looks like the adapter is not computable with Win 7 64bit.

View 2 Replies View Related

Sharing Kxp1121 From Windows 7 64bit To Windows Xp Pro 32bit

Dec 15, 2011

My win xp pro 32bit cannot add network printer kxp1121 from win 7 64 bit which is using epson lx series 1 (80). Request driver ' unknown Inf'

View 1 Replies View Related

Windows 7 64bit Networking With Windows 2003 32bit?

Apr 18, 2012

I wan to access a folder shared on windows 2003 server 32bit from a Windows 7 64bit ultimate WS. but after asking password, beside giving correct password, it asks again and agian and do not show folder

View 1 Replies View Related

Realtek RTL8188 Wireless Adapter Not Connecting To Home LAN

Feb 17, 2011

I'm trying to connect to the internet on another PC (on my desktop, not this laptop I'm sending this request on). I know my network is working OK, because I'm on it now (on my laptop), but the Realtek adapter is not connecting on my destop PC.

View 14 Replies View Related

Keep Losing Wireless Connectivity?

Mar 30, 2011

Noticed the last couple days that pages weren't loading on my laptop. Looked at the network status for the laptop and noticed that my network speeds would fluctuate from 54Mbps to 1Mbps, and various speeds in between. I had never had this happen before (I've had this router, a Linksys, for about 6 years). I thought maybe something was going on with the laptop. Grabbed my wife's laptop and she had the same issue. So, I checked the wired towers - their speeds are running at 100% all the time, no fluctuation. So, it has to be something with my router, but I'm not familiar with how to diagnose, etc. The router has a 3rd party firmware (DD-WRT) flashed on it, in case that matters. But I've had that on there about 4 years, nothing new. I've done a DHCP release and renew.

View 14 Replies View Related

Keep Losing Internet Connectivity?

Aug 29, 2012

ISP : ShawPC >> SMC Modem/Router >> Netgear Router >> PS3 and Denon Stereo Receiver ( Both hardwired to Netgear Router), 2 Laptops and 2 Phones connected wireless- The reason I do not use the SMC as a router is because I was getting terrible wireless signal- When everything is working properly I am getting great speedsroblem : I keep losing internet connectivity. On the wireless devices I still have have great signal strength but no connectivity. I need to run netgear genie oripconfig/release/renew to get it back. It always comes back but this is annoying.It also does this on the PS3 and Denon which are hardwired to the router..as with the other ones if I reset the router or do a connection test on the PS3 it will fix it. Finds IP but no internet connectivity.My PC has also started to lose connectivity and I need to do a ip release/renew and it comes back fine.The fact that this is happeneing on my PC would lead me to believe that it may be an issue with the Modem/router. Are there some settings I need to change on it since I am only using it for modem purposes? I have disabled the wireless on it but I don't think that would be the issue anyways

View 14 Replies View Related

Dell :: Weak / Spotty Reception With DW1525 WLAN PCIe Card - Windows 7 64-bit

Jun 23, 2010

I have an XPS 8100 and have been very satisfied for the most part, but have had a persistent problem with the wireless card, the Atheros DW1525 WLAN PCIe Card. The wireless signal swings wildly between 3 bars and 5 bars - and the computer is close to the router. The card only weakly picks up other signals and it is often weak and spotty. I compared with my Dell Inspiron 13 (which has an Intel wireless N card), and it is literally 5x as fast on speed tests, picks up a lot of other signals, and is always 5 bars.

I tried to reinstall the Atheros drivers from the Dell support site, and that seemed to do the trick for a while.... the card was picking up as many signals as my notebook and at the same strength and speed. But after a Windows Update, the problem returned. I tried to reinstall the drivers again but got blue screen errors when I attempted to install Atheros' drivers... I spoke to a Dell tech, did a full factory image restore, and while I'm not getting blue screens now, the signal continues to be weak and spotty. I have Windows 7 64 bit..

View 18 Replies View Related

D-LINK DIR-625 / Randomly Losing Wireless Connectivity

Apr 4, 2011

I have a DIR-625 router that has been acting odd lately. Several times a day at random my devices (laptop, android phones, PS3) will lose internet connectivity from my wireless network. They say they are still connected to the network but I am unable to access the internet or even the router config page. Everything works fine on Wired LAN computers. The only way I can fix it is by unplugging the router for a few seconds. I have had the router for over a year now without this problem. Seems like it may have started when we got our android phones.

View 6 Replies View Related

Losing Connectivity Every Couple Of Hours / Modem Or Router?

Sep 19, 2012

I have an issue with my current network where every couple of hours I will lose my connectivity and it will not come back unless I do a power cycle on my router/modem. I originally thought the issue was with my router, however I'm beginning to think it's an issue involving the modem. I've tried two different routers and this happens on both. My main router is a D-Link WBR-1310 (crap I know but it was free) and has lasted for years, and my modem is a Toshiba PCX2500 from Time Warner Cable. The second router I used to test this was an older Linksys BEFW11S4. I was going to replace my router, but when I saw that both of them reset after a few hours (today was only 5, last night it was connected for over 8 hours as I slept). I ran an IPCONFIG /ALL when I was connected with internet and when I was connected without and the only three changes were: [code]

View 2 Replies View Related

Cisco Wireless :: WLC526 And Two AP521Clients Keep Losing Connectivity

Jun 24, 2012

I have a UC520 in a building with several IP phones.  We installed a WLC526 and two AP521's for seamless roaming of cordless phones.  THe phones work great with no issues.  When I am running a ping test on a wireless laptop, i keep loosing packets.  It looses connectivity randomnly.  DHCP is given via Windows 2008R2 server.  Have a cisco 2948 switch also in the mix.  THe AP's are connected directly to teh front of the UC520. Why do phones work perfectly and not data?                    

View 2 Replies View Related

Cisco Wireless :: 1252AP Losing Network Connectivity

Sep 7, 2011

our autonomous 1252APs. It loses network connectivity irregularly and ends up disconnecting everyone. It may stay up from a few days to a few weeks. I don't see any log messages that give any clues to why it is doing this. We have 30 of these working worldwide (on the same software level and same config) and this is the only one having the problem.
 
Things I have tried: Changing software levels - there is a code level where it didn't seem to have this issue, but I can't run it because then I'm unable to monitor it in our monitoring system. Swapping out wireless access pointsRe-terminating the cable on the AP side, it was really difficult to get the network cable into the AP while swapping it outBlocking a company test piece of equipment from connecting using the mac address filtering (it connects with one of their test IPs - weird) – I still see it connecting though I don't see high utilization on the switch port when the issue happens I had a few cases open with TAC, and they were unable to find anything wrong - gave them sh techs of prior to the event and after the event. It was one of those where the tickets were open for a weeks with no updates.

View 9 Replies View Related

Using CISCO VPN On Windows 7 64bit?

Aug 23, 2011

I am using the following:

CISCO 2811 router.
Windows 7 64bit
CISCO Client 5.0.07.0440 64bit
HP Probook 4530s - 4 GB ram; Core i5

The issue is we recently purcahsed new laptops for our inspectors. They where running Windows XP 32 bit with CISCO Client 5.0.01 and every thing worked fine. When I upgraded them to the new laptops I am having issues with the VPN. The symptom is that the VPN connects ok and you can download files from the servers ok but when you try to up load a file that is larger than 80 KB it hangs on "Discovering Items..." then times out. What I have tried is:I hooked one of the laptops into the LAN and connect the VPN and the uploads work fine.I setup a SoHo router in our DMZ and hook the laptop to it and I have the problem my users are having at home as described above.Tryed truning off all Windows Fire Walls. -> Fails on upload.Tryed stopping the "Indexing Service". -> Fails on upload.Updated the CISCO client to the latest version. -> Fails on upload.Removed Anti-Virus. -> Fails on upload.Used IP addresses in place of FQDN. -> Fails on upload.We have other Windows VIST 32bit computers and they do not have these problems with their VPN. These are our first 64bit computers. I really do not want to down grade to Windows 7 32bit.I can make the running config available upon request but I doubt that is the issue being that our other computers are working fine but if there is something I need to do with the tunnel to get around this issue, I am game.

View 5 Replies View Related

Lan Is Not Working With Windows 7 64bit?

Sep 3, 2011

in windows 7 64 bit lan is not working

View 1 Replies View Related

Linksys Wireless Adapters :: Usb Adapter AE1200 Losing Connectivity?

Aug 21, 2012

I have the model AE1200 usb adapter and its been working great for over 6 months, but lately it has been inconsistently working.   It has stopped working then i have to reset the adapter and then it will work for a little bit and then it will do it again.   is this a common problem or is it likely my adapter is failing?   Is there an update that i am missing? 

View 1 Replies View Related

Cisco Wireless :: WLC 5508 Implementation - Some Users Losing Connectivity

Dec 3, 2012

We are implementing a WLC infrastructure in our company following the below scenario:

- WLC 5508, OS 7.2
- APs AIR-LAP1142N-T-K9
- 3 Wlans (1Open w/ Web Auth, 1 WPA2 and 1 802.1x)
 
Issues:Everything seems to be fine, but some users loses connectivity (when connected to 802.1x network) at least 3 times by day.

- I cannot see anything at WLC logs concerning the association/deassociation of any of these users.

- Only strange line in the logs is "RADIUS server 172.21.44.50:1646 deactivated in global list" (authorization server config)

- Also I see some "Coverage hole pre alarm for client" but that doesn't look like a problem...

View 6 Replies View Related

Realtek RTL8188CU Wireless USB 802.11n Slow On Windows XP?

Jun 24, 2012

When I install a micro-wifi-usb 802.11n with "Realtek RTL8188CU" on a old notebook with Windows XP I get maximum 1.5 to 2Mbits/s. Though installed on a newer notebook with Windows 7 I get 30Mbits/s.Other wifi-usb, Cisco Linksys WUSB100v2 does work on that Windows XP machine at 30Mbit/s, but the dongle is much larger The router Cisco WRT320N is just 5meters away and I always have excellent signal strength.I tried some other drivers without any luck. On the site of Realtek I don't find any driver except with some letter diverence at the end of RTL8188CU, which I also tried.

View 2 Replies View Related

How To Get Ip Address In Windows 7 64bit Laptop

Mar 6, 2013

i want to execute my project in lan so i need ip address in laptop.

View 1 Replies View Related

Netgear Duo RND2110 And Windows 7 64bit

Mar 18, 2011

I have a Netgear Duo RND2110 that I have installed in the system. One of the computers (Windows 7 Home Premium 64bit) will not allow me to access the Duo. I get the following message:-\192.168.?.?? is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you access permission. Login failure: accour currently disabled.

View 1 Replies View Related

Constant Disconnecting On Windows 7 64bit

Apr 23, 2012

I have a medialink USB adapter and medialink wireless router. I've had them configured for a couple of months and both seem to work fine. The issue is with only one system (main desktop computer running windows 7 64bit). I shut the system down over this past weekend and when I came back today, it said that it could not connect to the network and that the settings saved for my wireless network were incorrect.

After much frustration and googling, I finally performed a hard reset of my router (tiny button in the back) and redid all of the security settings (different SSID, different password). I finally got my desktop to connect to the network. When I connected, windows prompted me saying that I was sharing an IP address with another computer on this network. I canceled out of the prompt and my wifi worked fine. However, my computer has been randomly disconnecting from the network every few minutes for the last hour or so. I have to manually reconnect to the network every time this happens and it does not seem to stay connected for long periods of time. All other systems on the network (laptop and phone) do not have this problem.

Additional note: When first trying to fix the problem (before hard reset), I disabled the "Bonjour" service in windows AND ran the following command: netsh int ip reset C: esetlog.txt per a suggestion on a forum. I'm not sure if this would have changed anything even after the reset.

View 9 Replies View Related

Cabling / Cards :: Belkin F5D8053 N Wireless USB Adapter Losing Connectivity?

May 18, 2011

I recently purchased a Belkin F5D8053 N Wireless USB Adapter after my 6 year old adapter was unable to see my home network in the network list.

I installed the software but the adapter wouldn't connect to my home network so I reinstalled and updated the driver, still wouldn't work. Finally about 2 hours later it just randomly connected. Now it has been frequently (1-2 times a day) losing connection to my home network for around 3 hours, it can see a dozen networks in the list with full signal strength but won't connect to any at all then connects to my home network again several hours later.

I have switched between the Windows connector and the Belkin one and tried all 6 USB slots with no luck. I contacted Belkin support and they told me to try the device on another computer and see if the problem still happens but I don't have another computer to test it with.

I suspect this is a problem with my Windows installation rather than the hardware or router as my old card would freeze once every couple of days and was only fixed by powering off my computer as Windows was unable to kill the process to restart it.

View 4 Replies View Related

Linksys Wireless Router :: E3000 Losing Wi-Fi Connectivity On Multiple Device

Sep 7, 2010

Issue with Linksys E3000 router (firmware 1.0.02). I'm experiencing issues with the following wireless connections:
 
-iPhone 4G (wife's)
-iPod Touch 2G
-PC with wireless connection (non Linksys brand adapter)
-Acer NetBook (non Linksys brand adapter)
 
The issue is the connection gets interrupted and dropped, but the devices and the router DHCP clients table show the connections are still present. By interruption, I mean no data traffic is being transmitted.My wife's iPhone 4G and my son's iPod Touch wifi both show they are connected to the home network, complete with wifi bars being displayed, and the checkmark is present next to the home network connection in the the device settings for both. When I check the E3000 DHCP clients table, both Apple devices are listed as holding a connection. Yet both devices display network errors when trying to use any app that connects to the internet. By restarting the wifi connection on each, the connection is restored to the point where traffic now transmits. My wife and son estimate it is after about 10 minutes that they encounter the interruptions.
 
On the PC and NetBook, the connections have to be terminated and reconnected. I have not timed these to see how long before the connection becomes problematic.Interestingly, my ASUS laptop and my iPhone 4G do not have the issue, nor does my work laptop (Dell).There are no timeout parameters in the router config. Closest thing to it is the Beacon Interval, but I don't know which way to adjust it (up or down) to manage the devices that are experiencing interruptions. I have not made any interval adjustments...at this time, everything is set to default settings.This E3000 replaced an aging WRT54 (hardware v2) router so that I could have an N router in the house.

View 9 Replies View Related

Windows 7 ASUS Realtek 8111e Can't Connect To Internet?

Mar 10, 2012

About two weeks ago, I took out the old motherboard of my HP computer and put in a new ASUS M4A88T-M. The board is amazing, especially for the money, except that I can't connect to the internet.So, for the last two weeks I've power-cycled about a billion times, ipconfig /this/that/and the next thing over and over, I've winsocked, I've turned programs on and off and on again, checked that the LAN is enabled in BIOS, firewall is off, and probably a bunch other things from the 100's of google pages I've searched.I spent 45 minutes on the phone with my ISP, and the guy was 99% sure there is something wrong with the NIC. Windows says that the device is working correctly, and I think that it is. There must be some setting, some driver, something that will reconnect me to the internet.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved