Setting Up A Multi Ethernet Connection At Home
Nov 26, 2012
I have a single Ethernet connection into my house that is wired back to the main router right the other side of the house which is approx 40m away. The whole main house is cabled but I want an Ethernet cable to my TV,DVD and ps3, plus I need wireless for upstairs in my room. My question is, can I use the same wire or unit to connect the 3 different scores?and is there a wireless extender that will reach the further 40m to my part of the house?
View 1 Replies
ADVERTISEMENT
Jan 6, 2011
I have a new 2wire home portal that will not connect to my PC via Ethernet cable. However it will connect to my 2 laptops via the wireless connection. it would not make a wireless connection. but would via the Ethernet connection. How can I get the Ethernet connection working on the new portal?
View 5 Replies
View Related
Aug 11, 2012
I'm sure this may appear to have been asked before but I've scoured the Internet and can't find anything exactly applicable to the setup I'm trying to achieve. I had a sky ADSL connection in my living room that had my tv, ps3, NAS and netbook wired in. I've since changed to a sky fibre connection but this had to be installed in the master phone line which is upstairs. This obviously isn't a problem for all of the wireless devices around the house including the netbook and ps3 in the living room. The NAS and TV are still wired to the old router so can see each other with no problems. Any pc trying to connect to the NAS can just switch to the old router via wifi if desired. The only problem I have is that the TV can no longer access the Internet.
I initially tried to use ICS on the netbook (it's left on permanently) - it's wired to the old router and wirelessly connected to the new one. This appeared to be working for a while but is no longer playing ball. I've tried bridging the connections and the tv and NAS both had Internet access but it's very sporadic.Is this a reasonable setup or should I be looking for another solution? I can specify a manual ip, subnet and default gateway on the tv if necessary - I was going to point it towards the bridge's gateway but I don't know about IP?
View 1 Replies
View Related
Jun 21, 2012
is it possible for a client to choose a WAN to use when being routed through a Multi-WAN router? Something that could be configured as default route in linux or default gateway in winxp ?Or is this decision totally up to the router itself ? [code] Could now a client on the subnet 192.168.0.0/24 choose 1.1.1.1 as a default route for example? And if not, could this be possible if the router hat some secondary internal IPs for both WAN interfaces.
View 3 Replies
View Related
Sep 20, 2011
I'm currently in the process of buying the new property, which is in the build process and would like to put some cables across 3 floors, which would be connected to the router downstairs.
View 3 Replies
View Related
May 16, 2012
I have my PC connected to the internet by way of a USB WiFi dongle, tapping into the neighbours internet access (with permission).Obviously, this leaves my RJ45 Ethernet connection on the PC, free and unused.I have a CCTV system also, which, if to get the most out of it, requires an internet connection via RJ45 Ethernet.Is it possible to allow my CCTV system access to the internet via Ethernet, connected to my PC, and then using the WiFi dongle access which the PC is already using, also?If so, how would one do this, after physically connecting the Ethernet cable between the PC and the CCTV system DVR?
View 1 Replies
View Related
Aug 17, 2012
I need to have 7 individual ethernet outlets on my home network for rooms, living room etc. My router has 4 ports on it. What should I do to get the additional 3 outputs I need? Can I just plug a switch into my router for the additional ones I need? Or do I need a router with additional ports?
View 4 Replies
View Related
Jun 17, 2011
I want to setup a VPN, probally more just for the experiance and to learn how to etc, but i also print remotely and view cameras remotely etc and i though it might be safer then port forwarding hundreds of different ports.First question, would it be better or safer to set it up in Windows XP or windows Server as i would have to purchase windows server. I have XP and windows 7. and, what exactly is a VPN. I have done some reading up, but was woundering how exacly i would for instance, remotely view my DVR (cameras) over a VPN. Also, i want the server to be a remote HDD to store and access all data remotely, Backing up etc. This i think VPN is more made for right?And, i will need a server (computer running at all times) to setup a VPN right? as where the router is always on and accessable. I can acheive this and i think this is what i need.So there it is, im new to this side of things done about all i can with the old router and looking at extending my knowledge. Also i wouldnt mind it being SAFE.
View 7 Replies
View Related
May 5, 2012
I want to set up VPN at home so my friends can access network shares on my LAN and stuff. I have used this tutorial:(url) ?v=1s5JxMG06L4&feature=related so users are set up, and port forwarding on router is done as well. I am using Windows 7 Ultimate, and VPN is set up on this machine. The issue is that my friends cannot connect to my VPN from another Windows machine. When they try to connect it is asking them for user and password but later on after authentication they receive error 720 which says connection could not be established. When I went to the network connections and then to the properties of VPN (incoming connections) it says no hardware capable of accepting calls is installed.
View 11 Replies
View Related
Jun 28, 2011
(i have 2 PCs (1 desktop and 1 laptop) both running Windows XP connected to my modem/router. the desktop is connected through a wireless adapter, and the laptop is connected directly using an ethernet cable. i have run Windows "Network Setup Wizard" on both PCs and they are part of the same workgroup with File and Printer Sharing enabled. this is as far as I've gone in setting up my LAN and everything works fine. i am able to see both PCs under My Network Neighbourhood and can access files from either PC just fine. both PCs are also able to ping each other by IP address and comptuer name.the problem is this only lasts temporarily. for some reason, after a random amount of time (anywhere between 1 hour to a few days) the desktop will "drop off" from My Network Neighborhood on the laptop. when i try to click on the desktop or workgroup in Network Neighbourhood i suddenly get the error "You might not have permission to use this network resource. Contact the administrator of this server to find out if you have permissions. The network Path was not found." after this happens i am no longer able to ping the desktop from the laptop either by the IP address or computer name.however I am still able to ping the laptop from the desktop by IP address and computer name, although in Network Neighbourhood the laptop can no longer be seen as part of the workgroup. I am still able access the laptop and its files from the desktop using the \*computer name* command and this will bring up the laptop name again in Network Neighbourhood.one more thing i noticed is, once I've pinged the laptop from the desktop i found that i can again ping the desktop from the laptop, but only with the IP address. If I try to ping the desktop by computer name it still times out. oweer, this also lasts temporarily... after a while, the laptop is also not able to ping the desktop IP address again.the only solution so far is to restart the router. once the router restarts and both PCs reconnect to it, then the LAN is working fine again... that is, until the problem above starts up once again! cry.gifmy modem/router model is D-Link DSL-2640B.some additional info:
- i've assigned static IPs to both PCs so they always have the same IP address from the router.
- i've tried disabling the built-in Windows firewall on both PCs but the problem remains.
- i do not have any other anti-virus or firewall programs installed.
- i've disabled "Computer Browser" service on the laptop so that the desktop is always the Master Browser.
View 5 Replies
View Related
Feb 11, 2011
I am running AOL Desktop 9.1. When ever I start up it loads multiple home pages. How can I prevent this from happening?
View 3 Replies
View Related
Jan 18, 2011
I have a small home network. My goal is to use Windows Server 2003 R2 to setup a DNS Server that can create a few simple names for some devices on my LAN, such as my printer. My DNS server will forward other inquiries (like google.com) to OpenDNS. Additionally, I don't want to setup a domain controller for my network. I wish to continue using workgroups,how to setup a Windows DNS Server on a workgroup. My biggest confusion is the FQDN of my name server. By default, it's setup as "server.", where 'server' is the name of my Windows Server 2003 machine. My workgroup is named 'Home'. So I tried 'server.home', but this does not resolve. What DNS suffix do my other machines on the network use by default? Is my domain name on the network really my workgroup name? Another thing I want to avoid is configuring a DNS Suffix for every single client machine on my network in their NIC properties for IPv4. I have a D-Link router, and if I do an "ipconfig /all" on my machine, I see that my DNS suffix is 'router', which is the name of my D-Link router. I try setting my DNS Server FQDN as 'server.router' and that doesn't work either, so I'm out of ideas.
View 1 Replies
View Related
Nov 30, 2012
I recently signed up for Centurylink Prism TV and internet, they use a Cisco DDR2200 (modem+wireless router combo) which I've come to realize is only a "g" router, so I purchased a cheap Belkin N150 (which I intend to use as my main router). I've turned the wireless function off on the Cisco and have an ethernet cable running from a LAN port on the Cisco to the internet port on the Belkin.
The issue I'm having is how do I set up the IP addresses/DHCP servers for both routers? By default, the Cisco's IP address is 192.168.1.254 (I know, weird right?) with a DHCP range of 192.168.1.63 - 192.168.1.253. Whereas the Belkin's IP address is 192.168.2.1 . I guess I'm sort of at a loss on how to set this up to optimize my network.
View 5 Replies
View Related
Aug 14, 2012
I want to start using a VPN and would rather have my own server for it so was going to buy a kimsufi 2g with ubuntu installed on it, Have been looking on the openvpn website but cant find any tutorials on how to setup openvpn on ubuntu.
View 1 Replies
View Related
Mar 29, 2011
I can't get traditional broadband services, so I've been making due with Verizon's Mobile Broadband service. Problem is, it's expensive and has a 5GB cap per month. I read about powerline networking and thought it sounded good, so I bought all the adapters and a router. Problem is, I didn't have the prior knowledge to realize I also needed a modem as well. How or if I'd be able to set up any sort of modem in my home, considering services like Verizon can't reach me?
View 3 Replies
View Related
Feb 12, 2013
I want to set up my own home wireless network for the first time. Also this is the first time I'm using wireless router.nd trying to set up the network.Currently, I have ADSL+ router device that is configured in route mode and it has PPPoE credentials stored, so until now, I use ethernet cable to connect it to the ADSl router and everything works fine (Automatic IP, DHCP on notebook). Notebook also has wireless adapter, so I bought asus wireles router.This was supposed to be an easy install. According to the instructions all I need is to use this ethernet cable to connect to WAn port on wireless router and to follow Quick set up instruction. But this quick installation procedure fails.When I try to figure out why, I came accross to the fact that existing ADSl router has 192.168.1.1 and this new asus WiFi has also 192.168.1.1
View 5 Replies
View Related
Mar 4, 2012
I am buying a router with wireless soon and i am setting up an ADSL account.I only have one computer that will connect to this router.The router will be based in the living room area where the phone line is.My room (where the computer is situated) is quite far from the living room and i am not keen to drilling holes through roofs to wire some LAN cable.My plan is to use a wireless dongle in my pc to connect to the router for internet. Will this affect the speed of my downloads off the internet at all? will it be the same as if i was using a lan cable?I know file sharing over the network via WAN is slow but will my internet be?
View 1 Replies
View Related
May 28, 2012
So I have AT&T U-verse and am teaching myself networking and am wanting to mess around in creating my home network and set up static IPs for my devices. I know how to set them up, but I guess AT&T is saying that they have to allocate the static IPs....pretty much they are saying I have to pay them so they can say ok I can use the IP addresses from xxx-xxx-x-10 to and then depnding on how many I want to have depends on how much I pay. This makes no sense to me. Why should I have to pay my ISP for static IP address, from my understanding those are things
View 3 Replies
View Related
Jan 16, 2013
Im trying to rebuilt my parents home network. This is the general layout of what Im trying to go for when everyting is said and done.
modem---router1----switch1----router2---switch2
l l l l l l l l l l l l-direct-tv box
l l l l l l l l l l l-blu-ray player
l l l l l l l l l l-xbox 360
l l l l l l l l l
[code]....
and i dont know what switch 2 is yet because my dad ordered it and it has come it yet, all i know is its a linksys Now the big problem I keep having is keeping everything up and running for more than a day. Ive already configured router 2 to a staic ip address of 192.168.1.151 and disabled DHSP server thing which cleared up some of the inital issues I was having. But I continue to be plagued with issues of computers saying there are duplicate names on the network and the internet only working on some devices most of the time and the internet going out completely after a day or two. Now when the internet only goes out for some devices its usually limited to everything thats not hooked directly into router 1.but everything hooked directly into router 1 still has internetand the basic hard restart of everything does nothing to solve the problem. The only real way Ive been able to solve things on a large scale for a short time frame is to unhook everything and setup reouter 1 and the computers that hook into it on day one. come back on day two and setup switch one and comback the next day and so on and so forth. and usually by day 5 everything has worked for about a day or two then Im back with nothing working.
View 4 Replies
View Related
Feb 17, 2011
I am setting up a 1921 with two ethernet WAN ports going to two seperate ADSL ISP's (via bridged modems) and one connecting to the internal LAN. There is a single e-mail / web server behind the router.
I have been reading the following which is exactly what we want to do, but I have questions. Maybe failover would be better because Load Balancing seems a little too quirky without BGP. url...
How do we define public static IP's, the example seems to show DHCP?In order to detect if a line is down, it has to ping an IP address that is specific to the connection - correct? So could I use the gateway for the ISP? The issue I have with this is the gateway might be up, but the Internet down. Next, we need to make sure that when someone visits one of our public IP addresses, the return data is sent through the connection requested. What we don't want is a situation where incoming connections are not working.From experience, load-balancing causes certain websites and SaaS applications to break because requests are coming from two different ISP's. Is this the case with OER? Finally, any links, config or something to advise how a fail over only configuration would work given we have internal servers (PAT/NAT inbound would need to translate properly with the failover IP)? Basically if ISP 1 goes down, I.E. router cannot ping 8.8.4.4 then it switches to ISP 2, until ISP 1 comes back online and switches back? This would need to change the NAT rules for inbound as described.
View 4 Replies
View Related
Jun 15, 2012
I have a PC ready to use that I want to be used for sharing files, pictures and videos on between our multiple PCs in the house hold. I am going to have it constantly running (I have alot of cooling for it) but I need setting it up.I dont know if I should use Ubuntu Server or FreeNAS?
View 1 Replies
View Related
Feb 19, 2013
I have a problem figuring out how to setup a home network connection running a VPN. I have been looking through the internet for answers and am still not sure how it all works.
View 9 Replies
View Related
Mar 28, 2012
I am attempting to set up a proxy on a home network that is used for business purposes. I am not at all a networking person, I know enough to be dangerous. If I follow the steps listed here: URL Will this encrypt the data that is sent to the internet from any computer that connects to my network or just the one I follow the steps on?
View 7 Replies
View Related
Mar 4, 2012
I have a cisco asa 5505 firewall, and I have a normal home ADSL broadband router, the router currently connects via wireless to my pc.What I would like to do is basically connect the asa to my pc, then my router to my firewall.what the best thing to do here, run the aa in transparent mode, OR routed mode and do NAT on the firewall to the private ip address range of my router.
OR, would it be possible to get the outside interface of my asa to get DHCP from my broadband router so it will use a 192.168.1.x address on the outside, and then turn NAT off?
View 2 Replies
View Related
Jul 27, 2012
want to setup a small home network of about 10 PC's.I want them to share the internet connection of 25mbps.I also want Printer Sharing.
View 2 Replies
View Related
Oct 3, 2011
I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies
View Related
Aug 3, 2011
I currently have one wireless router in my house. Of course its hooked up the the modem, but i also have it hooked up directly to my desktop considering the router is on the desk where my computer is.I recently moved to a new house.One of the rooms has a huge brick wall in it, unfortunately the computer is in that room.AND, its on the far left side of the house, so the other side of the wall barely gets any signal (Enough to work, but it bounces and only gets about 2 Megabytes Per Second, which is awful, because the router sends out 20 megabytes per second due to our internet plan.) Now, my room is all the way on the far right side of the house, in my room, i get barely any connection at all, 20% is normal in my room. I have my Playstation 3 in my room, so I had to wire an ethernet cable from the wireless router, up through the attic, to my PS3. I can now get 20 MBPS while playing video games. While that is great, i still don't have a wireless connection back there.
What i want to know is, can i plug in another wireless router to the ethernet cable in my room, sending out another signal. So basically, im plugging up a wireless router to another wireless router, and want them to both send out internet.I plan on getting a gaming laptop in December and will be playing it most of the time in my room. I need to know if this is possible, and if it is, how do i do it?First off, let me state that moving the computer or router in front of the brick wall is completely out of question.Also, know a lot of stuff about computers, but know almost nothing about networking.
View 7 Replies
View Related
Jun 15, 2012
I have a PC ready to use that I want to be used for sharing files, pictures and videos on between our multiple PCs in the house hold. I am going to have it constantly running (I have alot of cooling for it) but I need setting it up. I dont know if I should use Ubuntu Server or FreeNAS?
View 1 Replies
View Related
Mar 2, 2011
If you can't home share on iTunes between Computers or AppleTV, try turning multicast on
1) login to router
2) Go to Advanced tab
3) Select Advanced Networking on Left hand column
4) Select checkbox to enable multicast streams
5) Save the changes
In order to get all my machines working, I also had to enable multicast streams on my network extender as well. The IP address for the network extender is 192.168.0.50 or type in DLINKAP in the URL bar and follow the relevant instructions for your model number.
Please note if you use a software firewall on your PC or Mac, you may need to also free up TCP port 3689 and UDP port 5353. However there are plenty of support articles at Apple / Norton / Microsoft / etc... on how to do this for your relevant firewall..
View 4 Replies
View Related
Jan 27, 2012
Well this process is self explanatory, setting up the network is easy but im running into trouble with my wireless devices connecting to the strongest signalIm not exactly sure if there is a fix for this yet or if they have not made a protocol to fix it. I have a big house with solid wall in which i have setup 3 wifi's. 1st Modem/wifi Router, 2nd Wifi access point, 3rd wifi access point. Now the problem im having is moving between the access points my devices such as my ipad are changing from one access point to the next whilst moving throughout the house (that is until it loses the first signal I believe or you turn your ipad wifi off/on so it reconnects back to the strongest/closest access point).
View 4 Replies
View Related
Mar 9, 2012
I have a question regarding setting up a wireless access point on a network. Lets say my router is going to connect to a switch. The switch puts out 192.168.4. addresses. I want the wireless router to do the same. So I turn off DHCP.Everything works fine and everyone can communicate. Here is my question. How do I ever connect back to the wireless router if I need to change the settings? If the wireless routers address is 192.168.1.1 I cannot get back to it since i am now on the 4. subnet. I have also tried changing the router's ip to an address on the subnet such as 192.168.4.100 but on two different routers this didnt work. One didnt me and said there was a conflict with the WAN IP. The other one would not let me get on the internet.
View 1 Replies
View Related
Aug 29, 2011
We want to set up a wireless user group in our town between a few friends and new people who are interested to join. As far as I heard I don't need a ICASA License for the 5.8GHz Frequency if we are using it for a non profit orginization, so we may use that.
1 x Routerboard
3 x Radio Plugin Boards
3 x 120degree Antennas
to set up a 360degree HS (Highsite).Then at each person's house we will need:
1 x Routerboard
1 x Radio Plugin Board
1 x Whichever Antenna
Is that correct? Then also if we wanto run VoIP on our network, how do I do that? Basicly we want to use it for gaming, file sharing and VoIP. No Internet of anything else.
View 2 Replies
View Related
Mar 28, 2012
I have been trying to get this setup for 2 days now and so far NADA.....
Router: Linksys E3000 - below is a list of all devices connected (hardwired T568B) to the 4 ports with a laptop connected via wireless
1. Main PC - motherboard: ASUS Maximus IV Extreme-Z (dual GB LAN ports)
2. Media Server - motherboard: MSI Z68A-GD80 (dual GB LAN ports)
3. Test Bench AMD PC
4. WD TV Live
Currently: I have all 3 computers running Windows 7 and connected to a Homegroup. I have given the correct permissions to enable sharing of files between each of the 3 computers and can transfer files from one PC to the next w/o any issues.
Desired: I want to connect my Main PC and Media Sever with a crossover cable using the 2nd LAN port on each motherboard, so that I don't have to go through the router to transfer data to and from these 2 PCs. I will have each PC also connected to the Linksys E3000 router via the 1st LAN port on each motherboard to supply the internet connection, so I am also not trying to "share" an internet connection between these 2 PCs. Basically, I want to run my home network through the Linksys E3000 and then a 2nd network for the 2 PCs using the crossover cable.
Current Problem: I disconnected the straight-through cables from the router to each computer from the 1st LAN port. I then connected the crossover cable from the Main PC to the Media Server and setup a new Home network in the Network and Sharing Center in Windows 7. Everything worked and I could transfer data to and from each these 2 PCs, so i know I wired the crossover cable correctly. Then I reconnected the straight-through cables coming from the router to the 1st LAN ports of each mobo, thinking that each PC would auto-detect the internet connection and reacquire my existing home network, enabling an internet connection again. However, this did not happen.
[URL] I also followed this how-to guide on microsoft.com, but when I get to Step 3 where it says that an "Unidentified network icon" will aprear in the Network and Sharing Center, it does not!
From Googling, reading, and troubleshooting I believe I know 2 things:
1. All of the hardware is functioning properly - when the straight-through cables from the router are disconnected, the 2 PCs are networked through the crossover cable and files can be transferred.
2. The problem is with Windows 7 somewhere - I think?
View 1 Replies
View Related
