I have a PC ready to use that I want to be used for sharing files, pictures and videos on between our multiple PCs in the house hold. I am going to have it constantly running (I have alot of cooling for it) but I need setting it up. I dont know if I should use Ubuntu Server or FreeNAS?
View 1 RepliesSo I finally got all my parts delivered to setup a home file/backup server this week.
It's currently running Ubuntu Server and I'm using Samba to share files on my network.
The server currently has a 2TB WD Green drive in it connected to a Asus M5A78L-M
This is then connected via CAT6a to my new Gigabit switch (TP-Link TL-SG1005D).
My home desktop is then also connected to this switch and again also through CAT6a cable.
Currently when transfering files I will get a perfect 100MB/s read from the server to my Windows machine. When copying from my Windows machine to the server I get around 30/38MB/s.
I know this drive is capable is faster speeds.
I have found ftp's write speed is much closer to what my Samba read speed is so I'm going to give it a guess that is a software problem rather than hardware
I have a PC ready to use that I want to be used for sharing files, pictures and videos on between our multiple PCs in the house hold. I am going to have it constantly running (I have alot of cooling for it) but I need setting it up.I dont know if I should use Ubuntu Server or FreeNAS?
View 1 Replies View RelatedI have a network that is currently set up in the following way:Modem -> vonage Motorola router -> wireless router Most computers are hard wired to the Motorola router. Some other ones connect via the linkseys wireless router. All computers are able to connect to the Internet. The problem I have is that I will be setting up a home computer as a file server connected to the Motorola router. The network acts as though it is two meaning that computers on one router can't see computers on the other router. What steps should I take in order to make all computers accessible through both routers.When I type 192.168.1.1 from a computer on the Motorola router, I get nothing, when I type in my actual ip address, I get the Motorola router. When I type in 192.168.1.1 from a linkseys connected computer, I get access to the linkseys router.
View 3 Replies View RelatedI have an Ubuntu Server, when someone is downloading a file from it, my bandwidth significantly decreases, how can I cap it?
View 5 Replies View RelatedI have setup a webserver on my home PC and I have forwarded port 80 on my router to the IP adress of the PC that is running the web server. The web server is working great; I can get to my web pages from outside of my home by going to http://MyIpAddress/Anyway, the problem is with the Windows Media Player plugin I'm using. I want to embed 6GB MPEG-2 videos into my web pages. I have some videos on my PC and I want to be able to watch them remotely by connecting into my web page. It works fine when I'm at home; other PCs can connect and play the videos no problem. The problem is when I'm at work. When I'm at work, I go to my web page (via my IP address in a web browser) and the Media Player plugin says "Connecting" for a minute, then it says Ready, but the video will not play. I tried using a smaller, AVI file (680 MB) instead to see if the problem was streaming such a large file, but the video still would not play.Do I need to foward more ports on my router so that Windows Media Player can connect back and get the information it needs?
View 4 Replies View RelatedI have been trying to get this setup for 2 days now and so far NADA.....
Router: Linksys E3000 - below is a list of all devices connected (hardwired T568B) to the 4 ports with a laptop connected via wireless
1. Main PC - motherboard: ASUS Maximus IV Extreme-Z (dual GB LAN ports)
2. Media Server - motherboard: MSI Z68A-GD80 (dual GB LAN ports)
3. Test Bench AMD PC
4. WD TV Live
Currently: I have all 3 computers running Windows 7 and connected to a Homegroup. I have given the correct permissions to enable sharing of files between each of the 3 computers and can transfer files from one PC to the next w/o any issues.
Desired: I want to connect my Main PC and Media Sever with a crossover cable using the 2nd LAN port on each motherboard, so that I don't have to go through the router to transfer data to and from these 2 PCs. I will have each PC also connected to the Linksys E3000 router via the 1st LAN port on each motherboard to supply the internet connection, so I am also not trying to "share" an internet connection between these 2 PCs. Basically, I want to run my home network through the Linksys E3000 and then a 2nd network for the 2 PCs using the crossover cable.
Current Problem: I disconnected the straight-through cables from the router to each computer from the 1st LAN port. I then connected the crossover cable from the Main PC to the Media Server and setup a new Home network in the Network and Sharing Center in Windows 7. Everything worked and I could transfer data to and from each these 2 PCs, so i know I wired the crossover cable correctly. Then I reconnected the straight-through cables coming from the router to the 1st LAN ports of each mobo, thinking that each PC would auto-detect the internet connection and reacquire my existing home network, enabling an internet connection again. However, this did not happen.
[URL] I also followed this how-to guide on microsoft.com, but when I get to Step 3 where it says that an "Unidentified network icon" will aprear in the Network and Sharing Center, it does not!
From Googling, reading, and troubleshooting I believe I know 2 things:
1. All of the hardware is functioning properly - when the straight-through cables from the router are disconnected, the 2 PCs are networked through the crossover cable and files can be transferred.
2. The problem is with Windows 7 somewhere - I think?
I have to share some PDF files with members of my organization, I have a Windows XP Pro box dedicated for this. Currently they can access it from within the office as a shared folder. I would like to make it available remotely is there a better way other then as a FTP access.
View 1 Replies View RelatedI have a PC ready to use that I want to be used for sharing files, pictures and videos on between our multiple PCs in the house hold. I am going to have it constantly running (I have alot of cooling for it)
View 1 Replies View RelatedI would like to set up a home server, that will sit under the stairs so that it can link to out BT home hub (v3). The idea is then to connect the printer to it, so that we can have both a wireless printer and a central file store for pictures/vids etc.Is XP ok for this? if so, what settings do I need to change/add?Is there any software that I need to make it work?How do I make sure that it is secure for external hacking? As it will contain our personal docs/photos etc and I would hate to use them.
View 1 Replies View RelatedI have a small home network. My goal is to use Windows Server 2003 R2 to setup a DNS Server that can create a few simple names for some devices on my LAN, such as my printer. My DNS server will forward other inquiries (like google.com) to OpenDNS. Additionally, I don't want to setup a domain controller for my network. I wish to continue using workgroups,how to setup a Windows DNS Server on a workgroup. My biggest confusion is the FQDN of my name server. By default, it's setup as "server.", where 'server' is the name of my Windows Server 2003 machine. My workgroup is named 'Home'. So I tried 'server.home', but this does not resolve. What DNS suffix do my other machines on the network use by default? Is my domain name on the network really my workgroup name? Another thing I want to avoid is configuring a DNS Suffix for every single client machine on my network in their NIC properties for IPv4. I have a D-Link router, and if I do an "ipconfig /all" on my machine, I see that my DNS suffix is 'router', which is the name of my D-Link router. I try setting my DNS Server FQDN as 'server.router' and that doesn't work either, so I'm out of ideas.
View 1 Replies View RelatedHow can I transfer file from my windows 7 os to virtualbox ubuntu at the same time??
View 3 Replies View RelatedI want to public to the internet a web + ftp server, all running in the same machine that now is a performance pc, in the future will be a qnap nas ts-220. I don't need extreme performance so my ISP gives me only 12 Mb down and 0,8 Mb up. I will use the nas as download station, ftp server and a web server when I'll public a personal site.
this is the config:
-modem/router adsl2+ that connects to the internet. ISP gives me dynamic ip! it has 192.168.0.1 ip and I think it cannot be changed.
-a firewall hardware zyxel usg 100 with all active UTM services. it has default ip 192.168.1.1. the netgear in the "attached devices" see the zyxel as 192.168.0.2, the same ip zyxel says to the wan1 port.
-a pc or, in the future, a nas that now has automatically assigned ip 192.168.1.34.
I must use a free or paied service as dyndns or something else. If the solution to retrieve everytime the dynamic ip is to set the ddns only in the router/modem netgear then it can only use dyndns.org or .com or .it with the dns of the associated ddns service. For example: if I set a dyndns.it account in the netgear I must set also the dns provided by dyndns.it because if I set google dns or something else the service cannot work.At the moment I tested only with a filezilla server running on the pc directly connected to the netgear, no zyxel in this test.
The config is:
netgear with ddns service provided by dyndns.it, activated with the username and password, in the wan I setup the dmz as 192.168.0.2, in the adsl settings setup the dyndns.it IPs. in the services of the netgear also provided a custom service with ports from 60000 to 60050 and created two rules one for outbound and one for inbound where I let data pass from the wan to the server in the lan 192.168.0.2.
filezilla running on the pc with windows 7 x64 with lan ip 192.168.0.2 mask 255.255.255.0 as th3 netgear and gateway of course the netgear 192.168.0.1. dns servers same as provided by dyndns.it. filezilla configured with only one anonym user without password for testing, default listening port is 60000, passive mode active with range 60000-60050 and for retrieving IP I set default, no Dyndns.it host cause it will not work.
So configured it works fine!problem is when I connect the zyxel between the netgear and the server.how change the default ip of zyxel? in configuration - ethernet - lan port is correct to set there the default and static ip to 192.168.0.3? there are many options! same as dmz you can set there the static ip and what ip?also when you want to public a server zyxel don't say nothing about port-forwarding. it says only create two address objects one with ip of the netgear and one with the ip of the dmz port then create a rule in the firewall section where you set wan to dmz and destination and origin ip selecting the two address objects previously created then you are ok...no, really no! and the ip of the firewall rules in the netgear? which ip do you must set? 192.168.0.2? or 192.168.0.5 if you set it up in the dmz port of the zyxel? no, it is a conflict so you must set another ip.to set correctly the server to be visible in the internet with the netgear + zyxel usg 100?
I use a limited usage internet plan and want that when I surf approx 10MB of data my connection automatically stops further download untill i reset or increase the usage.
View 2 Replies View RelatedMy roommate is running dual boot Windows XP PRO (SP3) and Ubuntu 10.10. I am running Windows XP PRO(SP3). Is there any software, that can run on both OS and can create a home network that will work between XP and Ubuntu. He has Samba installed but I have read that that works on Linux not Windows so he can see me but I can't see him.
View 11 Replies View RelatedWe are having a network of 7 computers and a server (Ubuntu server). The problem is, two of them are not connecting to the network. When i check the network card of these two systems, it seems working (the green light is blinking). When i replace these systems with a laptop, it connecting to the network and there is not problem at all.
View 4 Replies View RelatedI'm running Ubuntu Server in VirtualBox. When I select the internal network option for the network adapter and start up the VM, I only get IPv6 address. I need an IPv4 address as well. My host (running Windows 7) gets has both an IPv4 and IPv6 address listed when I run ipconfig. When I run ifconfig on the guest (running Ubuntu Server), it only lists IPv6.
View 3 Replies View RelatedI am running ubuntu 12.04, with apache2.My router configuration is set to forward port 80 to my local IP.The problem is I can only access the server as local host. Else it times out (from devices using the same network). I do not have sfw firewall enabled, neither shore firewall.
View 1 Replies View RelatedIf I have two servers, one running Windows Server 2003, and one running Ubuntu 10, what would be the best way to 'map' one's drive to another? Either way is fine. They are each in a different state, and each have an external IP. I just need to do some processing on the Ubuntu server, then write the file either to its own drive, and have the web server (Windows) read it, or, have it write to the Windows HDD, and have Windows read it.
View 2 Replies View Relatedwindows server 2003,ISA server 2000 Networking :: Connecting ubuntu desktop?
View 1 Replies View Related(Setup routing and iptables for new VPN connection to redirect **only** ports 80 and 443) Only my goal is a bit different. I am running a headless gui-less install of Ubuntu Server 12.04 that is being used for a variety of different purposes... I would like all traffic to travel un-prohibited through my ISP except for my transmission traffic. I have a VPN i subscribe to that allows me access for which I only want to direct a single port's traffic to. I am currently using a modified version of the code from the above link. My current code is below:
#!/bin/sh
sleep 200
DEV1=eth0
[Code].....
What I want to do is set up file sharing on both of my laptops so that they can share files both ways between them. I have in total 6 computers on my home network, and would like to limit the access to both to just the ones I want. I got about halfway before I hit an issue. My Windows 7 Ultimate is sharing both of its drives to my XP Home laptop, while being password protected for access from the other computers on my network. My XP Home Laptop cannot be shared without all the computers on my network having access too
View 4 Replies View RelatedI have windows 7 however, the other 7 all have Macs. What is the easiest way to set up file sharing so that all 8 of us can have secure access to a hard-drive so that we may all access music, pictures, and files specifically stored to that drive only. We do not want to grant each other access to our internal drives, only a network drive. I would like this shared drive to be secure.
View 4 Replies View RelatedIm in the process of trying to setup a home network. Computer A and Computer B are in the same workgroup. Username/password are the same.
Computer A = Windows XP sp3
Computer B = Windows 7 sp1
The two computers can communicate on the network. Can ping back and fourth with ip and computername. Computer B can access from what I can tell the whole C:/ drive from computer A. Doesnt ask for a password or anything like that. Just works the way it should.
However, I cant figure out how to share the C: drive from Computer B with Computer A.
Computer B
Click on C: >> Properties >> Sharing
And this is what i see on the sharing tab
It looks like its shared cause i see the \inteli5c. But when i go onto the other computer I cant access it. This picture doesnt seem to want to work. But that link is the screen that comes up when i try to access the C: from the opposite computer.
When I was using my Linksys router, I had no difficulties setting up Windows File Sharing on my computers but since I upgraded to the DIR-655, file sharing have hardly worked. Sometimes I could get one of the computers access files on another, but not the other away around. Most of the time, none of the computers have access to the files on any of the other computers. Two of the computers run Windows XP and another one runs Windows Vista. All computers are on the same workgroup and able to connect to the internet through the router. When calling D-Link tech support, I am told that they dont support file sharing and that I had to contact each computer's manufacture's tech support on the instructions on setting up the file sharing (each computer is from a different manufacture). One of the tech supports did drop the slight hint that I needed to recreate the home network, but when I tried to do that, all I could find is the settings to connect to the router (which I had set up when I installed the new router) and to enable file sharing (which is already done) and to assign the workgroup, which they were all are already assigned to the same group.
View 8 Replies View RelatedI want to get the ability to share folders between my PC using a Wireless router. One of the pc's is a Desktop running using XP SP3 and the other is a laptop running Vista SP1. how to set up away to just share certain folders between the two machines?
View 1 Replies View RelatedI have a desktop and a laptop each using xp. Each is set up to connect to the internet wirelessly, through different networks. I do not wish to disturb those settings.I want to set up a third, ethernet network, linking the desktop and laptop, for file sharing only, no internet.
View 11 Replies View RelatedBoth computers run xp. Desktop is had wired to router, laptop is wireless.If router is password protected, is the work group I created safe as well?
View 3 Replies View RelatedHome Group on Windows 7. I have added a room mate to my home group (just two of us in group). I don't want either of us to be able to view or share files, folders, etc. I think I've done everything on my end: turned off Network Discovery; turned off file and printer sharing; turned off Public Folder sharing. Also turned off automatic file/printer sharing in Norton firewall.
1) do I need to do anything else, and;
2) what does room mate have to do on his computer (if anything)?
I've spent quite a bit of time trying to figure this out on my own but somehow I don't feel quite sure that all my files/folders are not viewable by anyone else.
I finally got my 2 computers networked and seeing each other but when I try to share a file from comp B to comp A all I get is the data files, no .exe or application files. Can I not run a game stored on another network computer?
View 3 Replies View RelatedI run a home private server on Centos 5.5 I believe. A while ago, a surge destroyed a different computer with pictures on it that my parents would like to access. The hard drive itself is just fine, and I've backed up those files on an external hard drive. What I would like to do is allow my parents to access them through Samba. Samba has already been in long time use, but it is configured to only allow access in a jail inside each user's home folder on the root hard drive. I have a suitable hard drive already formatted and mounted that can fit all the pictures that they wish to have access too. What I'd like to do, is change the path that one of my users use to the mounted hard drive.
View 3 Replies View Relatedwe have a router with voip phones but no wifi, so i installed a separate wifi router but its ip is 192 range while the LAN is 10.1.1x range, how can i set it up so wirelessley connected PC's have access the file share and internet?
View 5 Replies View RelatedUsing the host file to block inappropriate websites on a pc works great.But i was wondering can you do the same on a wireless router.for some reason i can not find the option to do this on my netopia router.
View 2 Replies View Related