TP-Link 150Mbps Wireless :: WR743ND WAN-Port Fried / Possible To Re-configure?
Mar 15, 2013
Region : Argentina
Model : TL-WR743ND
Hardware Version : V2
My 743ND v2, connected to a Ubiquity AirGrid M5, got its WAN port fried due to a power surge. Lightning struck our desolate Paraguayan power grid close to my location, and I guess the power surge went throught the PoE adaptor of the AirGrid into the WAN port of the 743ND. ethernet ports and Wifi work fine, just the WAN is dead.
Is there any way to tell the router to use one of the 4 ethernet ports as uplink instead of the dead WAN port?Can't find such an option in the router administration, and the only hint I found on the web so far leads to a wildly experimental version of Open-WRT, which I would love to avoid...
View 11 Replies
ADVERTISEMENT
Feb 18, 2013
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4.23
Firmware Version : TL-WR740N_V4_130104
ISP :
not getting advertised 150Mbps speed , only getting 72Mbps installed the latest firmware TL-WR740N_V4_130104 and the performance is so bad that i cant even use skype anymore , the main reason to buy this router was to move from 54Mbps to 150Mbps but not sure what is wrong , how to achieve that 150Mbps speed
View 12 Replies
View Related
Dec 3, 2012
I have TL-WR740N router. ISP should provide me up to 100Mb/s internet speed. Actual measurements shows me about 80 Mb/s. The problem is when I enable 3389 port in Port Triggering my internet speed drops to 2,5 Mb/s. When I disable port triggering, speed become normal again.
View 3 Replies
View Related
Mar 25, 2013
Region : India
Model : TL-WR941ND
Hardware Version : V3
Firmware Version : 3.6
ISP :
We need to configure the AP in such a way, only 1 antenna to be used & not other two, to meet some mounting requirements/limitations. Will I be able to do this using any test/debug commands?
Essentially I want this AP to be operating in 1x1 spatial stream, & with no antenna diversity, so that I can connect only 1 antenna & be deterministic about AP using only connected Antenna RF port & not others
With out configuring anything, when I connect only 1 Antenna, I observed that signal is fluctuating on Client Application & causing the applications traffic stream disconnect.
View 1 Replies
View Related
May 13, 2013
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
View 3 Replies
View Related
Feb 16, 2013
Region : India
Model : TL-WR740N
Hardware Version : Not Clear
ISP : BSNL BB
I have a BSNL BB connection. When I use the connection directly, without adding TP Link router, all the websites open flawlessly. Once when I connect the wireless router, certain websites for example Yahoomail, pepperfry.com, yepme.com don't open at all. These are just examples, but I'm unable to access many sites which is a bit annoying. But sites such as gmail, youtube, facebook open clean, there are no issues. I didn't make any configuration changes too. I tried it more than three or four times, but there is a restricted access only.
View 4 Replies
View Related
Oct 11, 2012
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V3
Firmware Version : not sure
ISP : Talk Talk
My network is like this: ISP TalkTalk---ADSL modem-----TP-LINK TL-WR740N---Windows XP computer. I have configured the device by running the CD but it says failed to verify.Then I tried to refers to Quick Installation Guide (Manual) , there have offer a address 192.168.1.1 to go to web based quick setup wizard. But this site is not available.Other Wi-Fi devices are catching its signals even they are getting connected to it after enter the set up password and username but internet access has not been made so far.
View 4 Replies
View Related
May 13, 2013
Region : Hongkong
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP : PCCW
Just bought the router in Hong Kong to connect to my Mac. Typed in [URL] and everything is in Chinese with no link that I can see to change it to English. Is it possible to change the language?
View 4 Replies
View Related
Jan 5, 2013
Region : Argentina
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version : 3.12.4 Build 100910 Rel.57694n
I did a hard reset and after that, when i power on the router, it works for aprox. 15 seconds, so i can access the interface at 192.168.1.1, but after those 15 seconds it doesnt respond. The lights are on as if it was perfect, but cant go on admins interface and ping doesnt work either. I did several resets, did the 30/30/30, and clicked on reset to factory defaults on those 15 seconds but nothing happens.
View 3 Replies
View Related
Mar 3, 2013
-Region : Others
-Model : TL-WR740N
I am using TP-Link TL-WR740N as mentioned.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
View 2 Replies
View Related
Apr 12, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
wan led on my router is not illuminating. My internet connection is fine.I have pppoe connection. What may be the reason ?
View 1 Replies
View Related
Jan 26, 2013
Region : Australia
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
I am posting this in the wrong place but thats only because I cant find the forum for the TL-WR642G ver 3.6 device.Basically I am unable to see any QOS configuration and I wanted to know if this is available to this model ?I know the ver 4.0 firmware update states that QOS is added but can I update a 3.6 device using a ver 4.0 firmware ?
View 2 Replies
View Related
Mar 29, 2013
Region : Others
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP :
Going to a hotel where they'll charge me (a lot) for WiFi in the room, for only 1 device. Will the TL-WR702N let me share this 1-device internet connection among several devices?
View 1 Replies
View Related
Apr 25, 2013
Region : Colombia
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 110915 Rel.40896n
ISP :
i have a TL-WR740N router.I need connect 2 networks.
network 1 => 192.168.1.x connected to WAN port.
network 2 => 10.0.0.0.x connected to LANS port.
Router
assigned address:
192.168.1.101 WAN
10.0.0.225 LAN
[code]....
i can't connect to 10.0.0X network (pcs connected to router lans ports)I need bidirectional connection to networks.
View 3 Replies
View Related
Feb 19, 2013
Region : China
Model : TL-WR741N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am American living in China. My Chinese reading is not so good, I am still learning. The interface for my router comes up in Chinese. Is there a way to change the language to English? So far, all I can do is get the set-up interface through IE, but I can not set it up!
View 1 Replies
View Related
Jan 26, 2013
Region : Australia
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I have TL-WR740N router. I dont know how to stop and start wifi signals.
View 4 Replies
View Related
Feb 8, 2013
Region : Romania
Model : TL-WR740N
Hardware Version : V3
Firmware Version : 3.8.2 Build 080628 Rel.37228n
ISP :
I have a problem with my tplink router. In first of all I can't find my model in this forum. I have TL-WR641G [108M] and I cant upgrade my firmware.
My current firmware is:
Firmware version: 3.8.2 Build 080628 Rel.37228n
Hardware Version: WR641G/642G v3 081520C2
I tried to download the latest firmware from this page (V4) [URL] I press browse button from web interface, I select wr641gv4-en-up.bin and I press Upgrade but nothings happened. I read on other forums this router have 1MB internal memory and wr641gv4-en-up.bin have 1.07MB.
View 3 Replies
View Related
Apr 28, 2013
Region : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
how to change my router password?
View 2 Replies
View Related
Mar 12, 2013
Region : Bangladesh
Model : TL-WR720N
Hardware Version : V1
Firmware Version :
ISP : Is pros
After i bought the router it was working perfectly. But after using 1 week it freezes now and then. Happens around 10-30 times a day. The one or two led lights stops flashing and no device can connect to the router or asses internet. Another issue is that sometimes i cant connect any device through wifi (tried with android phone and ipod) and and but works perfectly on my pc. If i restart my router is works perfectly but after 1 min-3 hours sames problem happens either router freezes or cant connect though wifi
View 14 Replies
View Related
Dec 27, 2012
Region : Canada
Model : TL-WR700N
Hardware Version : V1
Firmware Version : latest
ISP : Cogeco
I have a WR700N set up in bridge mode so as to provide a wifi signal in far end of our home. I used Bridge so we can tell which router we are connecting to. So we have two SSIDs (MySSID1 and MySSID2) Both with secure log-in. This works fine for about a day, and then disconnects. I then have to mess with the WR700N by plugging it in and out, maybe logging into it and changing something. Then it will work again - for a day
I updated the firmware with no change. Main router is a Dlink 615 with IP of 192.168.0.1. connected to cable modem. TP-LINK is set at default of 192.168.0.254 and gets a wireless signal from dlink.In an attempt to improve situation, I now have both units set to channel 11 and with fixed 20Mhz channel width. b/g/n on TP and g/n on dlink.
View 6 Replies
View Related
Mar 23, 2013
Region : Philippines
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am having troubles configuring TL-WR740N. After I connect everything and turned in on, the system Light is ON and the power light is also ON and nothing else. I Connected my laptop to the 1 of 4 LAN ports and the WAN to my modem.
View 2 Replies
View Related
Dec 29, 2012
Region : UnitedStates
Model : TL-WR720N
Hardware Version : V1
Firmware Version :
ISP :
Just bought a new TP-Link TL-WR720N router. Hooked it up and got internet access just fine. However, when I go to [URL] or http://192.198.0.1 to try and login to setup the router, I just get the standard message:
Username or Password is incorrect. Please refer to the troubleshooting below:
Is the "Caps Lock" enabled on your keyboard? The username and password must be lowercase, please ensure that the "Caps Lock" LED is disabled on your keyboard and try again.Forgot your username or password? Please reset the device to the factory default settings if you have forgotten your username or password. The default username and password are both set as "admin". Note: The settings will be restored to factory default after the resetting.How to restore the device to the factory default settings? Firstly locate the reset button on the rear panel of the unit, whilst the device is powered on press and hold the reset button for more than 5 seconds, the device will then reboot and restore itself to the factory default settings. I am using a Cat 5e ethernet cable, I don't have NOD32 or any other antivirus or firewall blocking access, I even changed the settings and disabled IPv6 via ethernet since that was also suggested in the FAQ, but I still don't get a login screen.
I reset the router, rebooted my computer, unplugged the modem/router, reset everything again, double checked the IP address and pinged the router with excellent results, but nothing makes it so the login screen appears.I then hooked up the router to a PC running Windows XP with Internet Explorer 8 and the login screen works fine like you would expect. Went in, adjusted settings, everything works ok. This router is very new, it should support Windows 7 and Internet Explorer 9, shouldn't it? I don't want to have to keep old computers around just to login and change settings on my router.There must be some default setting in Windows 7 or in IE9 that causes this issue with the TL-WR720N router. I've tried everything that seems to cause the same issue on other routers, both TP-Link and other brands, and none of those seem to be what's causing this. TP-Link might want to address this ASAP and fix whatever causes it, otherwise this router is not going to do very well in the marketplace if setting it up with Windows 7 PCs with IE9 is a problem. It should work with default settings, same as it seems to with Windows XP and IE8.
View 7 Replies
View Related
Feb 7, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : BSNL
how to get a graph of the router statistics like upload and download speeds - both total and per device? Something like MRTG. The closest I came to getting data from the router was with RouterStats-Lite, but I was unable to get it to work.
View 6 Replies
View Related
Dec 29, 2012
Region : Canada
Model : TL-WR700N
Hardware Version : V1
Firmware Version :
ISP : ShawCable
I have just bought the device. I works fine as a AP out of the box. I want to use it as a repeater of my wireless network which uses a Linksys Simultaneous Dual Band N Router WRT400N
1. To do the setup, I have tried to login at 192.168.0.254 I cannot do this (a) using a wireless connection to a Linksys router which is connected to the cable modem and (b) wired connection to the router which is connected to the cable modem. The attempts get a timeout messaage.
2. The default gateway is 192.168.1.1. The DHCP server has the same address. My computer is using 192.168.1.101.
3. I use McAfee Internet Security software.
View 1 Replies
View Related
Feb 18, 2013
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
i m experiencing wireless disconnects every 5 or 10 minutes and all i have to do is too disconnect from the router in windows from Wireless connections panel , and reconnect and it ggets fixed for some time again . i got so frustrated that i changed to openwrt , the disconnection problem is gone but not getting the 150Mbps.
View 7 Replies
View Related
Jan 23, 2013
I have high speed internet connection. The following image shows how my ISP provides internet connections:
ISP.jpg
I am required to put IP address in my computer network settings. This IP is used to go to login page to put username/password. It is a web based authentication(kind of captive portal you can call). Done! I am connected to the internet. Super fast!Now, I would like to share this internet connection between two computers using WR741ND router. So, what I am doing is having both these two computers connected to the router using LAN ports whereas my ISP cable to the WAN port of the router. IP settings of both the computers are set to: Obtain IP address automatically.Configuration in the router:
Logged into the router--->Network--->WAN--->Static IP--->Settings saved
I am able to connect to the internet using any of the PCs. The problem is I am unable to access the internet simultaneously using both the computers. When one computer is in the process of loading website and I try to open a website on second computer the second computer does not start loading website at all and even the first computer stops opening the website.What change do I need to make in the router configuration? Can this internet connection be shared at all?
View 2 Replies
View Related
Mar 13, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version : 3.16.3 Build 130104 Rel.55864n
I have upgraded to the openwrt firmware in my router. I am having some problem to use it because I dont have the GUI access. Anyway I want to revert back to my original firmware. I cant use the internet through my router. How to revert back to the original firmware
View 14 Replies
View Related
Feb 20, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.16.3 Build 130104 Rel.55864n
ISP : ISP
My Wireless setting
Wireless Radio:Enable
Name (SSID):Trojan_Horse
Channel:8
Mode:11bgn mixed
Channel Width:Automatic
MAC Address:A0-F3-C1-97-87-FA
WDS Status:Disable
I cannot access the WiFi signal beyond 20m....There is no obstacle in the path. My receiver also supports 802.11n. There is also no local network interference.
View 11 Replies
View Related
May 1, 2013
Region : Ireland
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP : Three Mobile
I have recently purchased a new desktop computer that does not have an internal WiFi card. To remedy this I bought the TP Link TL-WR702N. Currently my access to the internet is provided by a mobile WiFi router (one of these: { URL}, that spreads a wireless signal throughout my house for things like my phone and laptop to connect to. I was under the impression that the WR702N would be able to connect to this network and let my new computer run on it (I believe it's called client mode?)
Now so far I have not been able to get my computer to recognize the existence of the TP Link modem, despite both Ethernet and USB cables being plugged into the computer. I think I need both logging in and changing the mode from AP to client mode.
I emailed support and was given the instruction to read this FAQ [URL], however, when following those instructions, after clicking on "Change adapter settings" instead of reading the router, all I get is a blank screen.
View 1 Replies
View Related
Feb 7, 2013
Region : Others
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
I bought today new TP-Link TL-WR740N and I connected it with my cable modem as it is in manual instructed. There is problem with outgoing signal from router. It is about 1/10 from it should be (it is around 2Mbps from 20 Mbps). Same speeds are going out from router through LAN port and WiFI signal.
View 6 Replies
View Related
Dec 5, 2012
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP : CenturyLink
I've just received my new TL-WR702N that I want to use as a repeater (downstairs) for my router (upstairs). I've tried the configurations listed on the TP-Link website, but none of them give me internet access. In fact, the local area connection shows the TL-WR702N as an "unidentified network".
View 2 Replies
View Related
Apr 8, 2013
Region : Brazil
Model : TL-WR470N
Hardware version: v2 Firmware version
latest (updated yesterday)
ISP:
My Iphone doesnt recognize my printer (HP Photosmart D110a) when I try to print something from it by AIRPRINT. After updated my printers and routers firmwares, the problem continues. Ive been read a lot and seems that the problem is caused by a problem with IGMP or Multitasking protocol.... But I dont find these in my routers page even after updated my firmware.
View 3 Replies
View Related
Apr 21, 2013
Region : Others
Model : TL-WR741ND
Hardware Version : Not Clear
Firmware Version :
ISP :
after year and a half of using TL-WR741 ND router, it suddenly stop working during the night. I have no problems with router before this happened (I think only one or two reset in 1 year and 6 months). System led light does not flash (some sytem error) and I can't access to 192.168.1.1 router setup site. I tried almost everything, unplug power, reset etc. for almost 100 times, reconnect the router with modem and PC in all posible ways, but still can't establish connection or even access to router's setup. Obviusly internet works fine?
View 3 Replies
View Related