Wireless Options Powerline Or Usb?
Jun 18, 2012
After moving my PC for the 3rd over the past year ive decided that having a more wire-"less" option may be the better option as supposed my previous method of having a 10m ethernet cable from my switch to my PC. ive looked at two options, first the powerline HD (was drawn toward the belkin 1gigabit ones as i have a gigabit switch) or to remove the cable completely and using a USB wireless dongle (similar to the Edimax EW-7811UN Wireless 802.11b/g/n 150Mbps Nano USB Adaptor) . i havent had much experience with these USB wireless things as i used be put off by the compatibility and config (software stuff). i have a 3com wireless 54mbps.. PCI card but i cannot install the drivers for it on my xp 64bit machine.
View 2 Replies
ADVERTISEMENT
Jan 6, 2012
Add a second wireless access point via Powerline.Broadband cable modem to wireless router.Current wireless router provides coverage to part of the house. I purchased a powerline adapter to extend the network.Powerline works well when hardwired to the remote adapter. However, for the life of me, I can not get the 2nd wireless AP to work when plugged into the powerline.I understand that the 2nd AP should be plugged into the Powerline via a LAN port and not the WAN port. I have also read that the DHCP should be turned off on the 2nd wireless AP. My second wireless AP is a E2500. There are 2 references to the DHCP - one is connection type and the other is DHCP server. Do I need to turn the DHCP server off and make the connection type static instead of DHCP?Also, when I change the connection type to static vs. DHCP, I am asked for an IP address, subnet, gateway, and DNS entries. What entries should I be using for the gateway and DNS?The DHCP pool on the 1st wireless router is 192.168.2.2 to 192.168.2.100 and the LAN IP address is 192.168.2.1
View 8 Replies
View Related
Apr 30, 2011
if it would be possible to use a powerline adapter to connect a to second router? I'm currently hardwired like this, but I'm just wondering if powerline would work the same way, as I'd like to switch which room the wireless is running from.
View 3 Replies
View Related
Jul 10, 2011
Just got a e4200. However I also have a cisco av power line adapter which worked fine. However when connecting to the 4200 it doesn't recognize the Internet. Have rebooted, reset switched ports etc. But it still doesn't work. It sees the network but not the Internet. Have tried everything ikon but no luck. Cannot connect my directive to the Internet. If I can't get it to work will have to run a 50 foot cable.
View 5 Replies
View Related
Feb 3, 2012
my goal is to share my cable modem signal over my two story house using two wireless routers. The delima is that the routers don't support wireless bridging and if they did, the signal is too weak to make it worth while.
The remedy I came up with... buy a pair of powerline network adapters and connect one router to the other so I could have a good signal upstairs and then a good signal downstairs.
Downstairs, I have the cable modem connected to the Linksys WRT54G router, which has a line out to my blu ray player, wirelessly feeds a PC downstairs and then has a cable run to the powerline adapter.
Upstairs, I have a cat5 connecting the powerline adapter (which was tested and works with laptop) to the data input port on my second wireless router, the netgear wndr3400.
I can't get the netgear upstairs to pull an IP address from the linksys router downstairs over the powerline network.
View 6 Replies
View Related
Sep 27, 2012
I'm putting together a design for a new office with the following requirements:
10 VPN users.For Ethernet – 24 ports POE 10/100/1000
Probably go with VZ FIOS so EthernetAbout 2000 square feet so 2 WAP's should do it I'm thinking a CISCO881W-GN-A-K9 ISR with a SRW224G4P-K9-NA switch should do the trick. This will give me an integrated AP but I need a second one. Do I need to order an autonomous one or does the 881W do some sort of WLC function?
View 1 Replies
View Related
Jul 25, 2011
Our company is moving to a new location temporarily and we will be looking to do wireless for our network instead of wired. We have a dell power edge 2900 server running windows SBS 2008 and a switch with more than enough ports for what we need.What i need to know is how exactly to do the wireless and what hardware would work best for us. We plan to have approximately 45 computers hooked into the server and have some wired but for the most part wireless. Also we would want to look into advanced security options for our wireless set up as we will be in the same building as a few other companies.
View 5 Replies
View Related
Jan 3, 2013
I cannot seem to locate a good document for SAP (standalone AP) security options to authenticate a connecting device at layer2 and/or at layer3. What the highest level of security I can use with BYOD such as Tablet devices (Samsung) and/or laptops.
View 2 Replies
View Related
May 16, 2013
What are the new external antenna options?
View 1 Replies
View Related
Nov 27, 2011
as per reading documentation, i only see the dual-band antenna option for this device. i am planning to use this for mulch-site bridging. can i substitute the dual-band antenna with a single-band high gain antenna for such deployment?
View 2 Replies
View Related
Apr 10, 2012
I'm using the e4200 in a big old house with lots of walls, including rooms separated with brick. Wiring access points would be difficult given the problem of pulling wires. I do have lots of kids and devices connected including DirecTv, iphones, ipads, laptops, and PS3. Is there a range extender? Do I care if an extender only supports 2.4Mhz if I use the same SSID anyway?
View 5 Replies
View Related
May 10, 2012
Can the EA4500 be wall mounted? I don't see any provisions on the underside EA4500 to support securing to a wall.
View 9 Replies
View Related
Jul 11, 2012
I've got a number of 3502i's that I need to mount in a new classroom that does not have any ceiling (except the floor decking above). Ceiling is roughly 30-50' up. Contractors are going to run several 2" (or whatever we want) metal pipes from the ceiling down to a more reasonable level to mount the access points on and get below the hvac ducts/etc in the ceiling.
Problem is I can't find any bracket or mounting options for this! What are others using in this situation for mounting one of these access points onto a metal pipe such as this? I've checked Oberon Wireless, Terrawave and I don't see anything glancing through the product catalogs. Anyone mounting access points this way?
View 4 Replies
View Related
Jun 19, 2012
I'm configuring a 2504 wireless controller with # of 1142 APs, wondering is there an option to turn off the WLC/ APs during after ofice hours? such as turn off power/RF options etc
View 5 Replies
View Related
May 23, 2012
I own an AG214 ADSL2 router that I use for my desktop PC. I now however also have a WRT54GL for wireless connection. I connected the WRT54GL to my AG214 via ethernet. Everything works fine, I have wifi and I can use it to connect to the internet. However when I go to my router (192.168.x.x) I can't seem to be able to find a wireless tab to configure my wifi settings. The network right now is unsecure and has a default name (linksys). How do I access my wireless settings? When I access my router it does go to the AG214, do I need to access the WRT54GL? If so, how do I do that?
View 4 Replies
View Related
Oct 11, 2012
just wondering whether getting a 500Mbps powerline kit over a 200 Mbps kit would be much of a benefit, seeing that comcast internet speeds only advertise 50Mbps or 105Mbps speeds.
View 2 Replies
View Related
Nov 30, 2012
I have two powerline adapters of teh same type (bought in a kit). The user manual says "plug them in and they will recognise each other". Well I did, and they don't. I tried plugging in computer to the far one via ethernet cable, and my wireless internet router to the near one by ethernet cable, and I cant get Internet on the far computer. It does get internet through a wireless dongle on the far computer, so Internet is definitely working. but when wirless dongle is out, no Net..So how do I know what is going on in this closed system of the powerline adapters? Should I be able to see the network on the main ("near") computer next to the Internet wirless router? it runs Windows 7.
View 1 Replies
View Related
Aug 22, 2012
I want to add a cisco or netgear powerline adapter to a building.I have read that for home it works really good, but i am going to add it to a building--A 5 floors building.So i would like to know if anyone has done this before and it works. This is a commercial building.And it is not easy to run cables, that would be the second option if the powerline do not work well.
View 3 Replies
View Related
Apr 29, 2012
Here is what a wired portion of my network looks like:
internet---dsl modem---airport extreme---powerline ethernet adapter****powerline ethernet adapter---5 port switch---(ip camera & ioBridge 204)
The airport extreme is also hardwired to a PC that I use to view the IP camera.The issue I'm having is with the connection to the IP Camera.The connection to the camera worked for a long time, then starting dropping periodically and now it doesn't work at all.The ioBridge connected to the same switch as the camera connects to my network and the internet just fine.
Here's what I've done to troubleshoot: I plugged the camera in to my airport extreme and it worked fine. When I plug my camera into the other end of the powerline ethernet adapters, though, it doesn't work (even though the ioBridge does). I replaced the powerline adapters today (because they had worked before, so I guessed something had fried in them) but the connection still doesn't work.
When I ping the camera (when it's on the other side of powerline adapters and "not working") the response time is around 3ms (good) but there is about a 33% loss rate (bad).I'm guessing it's the loss rate that is keeping it from displaying the video stream on the computer...but I can't think of what changed between when it was working and when it stopped working that would cause it lose packets like that.
View 2 Replies
View Related
Jun 16, 2011
I'm planning to network using powerline adapter for gaming. I know it's not the best solution but i don't have any other choice. My doubt is to buy whether a 500Mbps or 200Mbps. Will this 500 Mbps increase performance ?
View 2 Replies
View Related
Sep 20, 2012
I am looking at using a TP-Link Powerline Adapter (TL-PA211 Starter Kit) and a Trendnet 4-Port Broadband Router Tw100-S4@1CA (both listed on Amazon) to connect my Hitachi L32A402 HDMI television and a Roku XD|S to the internet to use Netflix. And also to connect my housemate's new laptop.
I believe the setup would be from my Dell Vostro desktop to the Trendnet router to one of the TP-Link Powerline Adapters. This would be on the second floor. Then in the basement I would need to plug in two additional adapters ... I would connect one to the Roku and then to the Hitachi tv and connect the other one to my housemate's computer.
My questions are:
Can I keep the computers not visible to each other? We would both like to maintain our privacy ... and I don't know if we connect everything up this way if our computers will be open to each other. Is this called putting them on a separate network?
I saw something in the documentation in this manual [URL]. I think on page 20 it is telling me I can give one adapter a different name to put it on another network, but I am not sure. And I also see that it also says for there to be connectivity they need to have all the same name "HomePlugAV".
So, if the tv and the main adapter have "HomePlugAV" as a name, and my housemate's adapter has a different name ... then they will all work (get on the internet) - but my housemate and I will have privacy?
Are there any issues about anyone being able to access my computer through the tv ...
View 4 Replies
View Related
May 20, 2012
I had an old Belkin wireless USB adapter that I used with it for the first few days, but I got tired of the slow speeds that I had always known to be associated with that card. So today I went and bought a CISCO PLEK400 powerline networking adapater. Brought it home, plugged it in to my router in my living room, plugged it into my PC in my bedroom, gave it a quick little test drive. First I went to speakeasy to test the up/down speed. Never more than 1.5Mbps down/1Mbps up. My laptop, running wirelessly through the same router, generally hits 20Mbps down and ~2Mbps up. So I plugged the ethernet cable into my laptop, to see if maybe it was the network card in my desktop that was faulty. Speakeasy speed test showed 1.5down/1up wired for laptop as well. Pinging google through command prompt, on either laptop OR desktop while wired, nets a ~300ms response time.
View 1 Replies
View Related
Oct 4, 2012
A friend of mine runs a small hotel, and would like to enable Wi-Fi in the guest rooms. (One thing to know is the hotel is an old farm house, the walls of which are made of clay/mud/brick/cow poo/thatch etc etc) url...The pink area is a rough guide to the current Wi-Fi coverage. This is broadcast from a 3 antenna Wi-Fi transmitter. (Mostly happy with it's performance.)The transmitter is attached, via an ethernet, to a Powerline adaptor (Blue dot).The other end of the Powerline system is in an office, above the kitchens (Red dot). This is attached via ethernet to the main router.The Blue area's are the guest rooms. This is where he want's to supply a signal to.
1) Buy 6 or so powerline adaptors, that have built-in WiFi, and sign them out on a requested basis. Something like this: ZyXEL WRE2205 Powerline Wireless-N300 Range Extender | Ebuyer.com
2) Buy 3 or 4 basic Powerline adaptors, connect via ethernet to 3 or 4 dedicated transmitters. Because of the risk of theft, all this would be wired up in the loft space, out of sight. Plug extensions would have to be wired up into the loft areas for the Powerlines to plug in to.
3) Dispense using the Powerline network completely. Run an ethernet from the office to room 5/6, then connect up to 3 or 4 dedicated transmitters set up in loft areas.
View 1 Replies
View Related
Nov 29, 2011
I have a duplex home in an urban setting that seems too vast for a single wifi router. Additionally, it seems that there is significant speed degradation through wifi. According to my speed tests, I can lose up to 70% of my contracted internet speeds (of 15 mbps) via the router (which I am hoping that the Apple TC can fix although I'm sure that sometimes it's the cable co's fault!)I have read that if I can add a wifi router to the second floor that would work with the signal, however that speed would be the same degraded one.So, I have been doing lots of reading on the Powerline devices and I'd like to know if I can do the following and if so, how:
1. Connect the wifi router (soon to be an Apple TC) to the cable modem, as I do now, but then run the ethernet cable through the TC to the Powerline and Powerline network that way.
2. Connect my iMac to the internet via Powerline
2a. Can I then use Powerline fo Home Sharing, Air Play, and so on?
2b. Back up my iMac to TC?
3. Connect my internet ready TV via Powerline (currently conencted via wifi).
4. Connect a second wifi router on the second floor via Powerline and it be on the same wifi network as if I am using the second router as an extender.
5. There is a tenant on the 3rd floor who receives a separate electric bill. Can I assume that they would be shut out of my Powerlined network?
6. Lastly, connect my iOS devices to wifi?
View 2 Replies
View Related
Aug 11, 2012
I have setup Powerline Adaptors connected to a BT ADSL Broadband Modem and to a Humax Freesat box, but I keep getting a message telling me that there is no internet connection.
View 4 Replies
View Related
Jan 8, 2012
I have recently bought a homeplug to connect to the internet since my broadband is downstairs from my pc. I have plugged in the two homeplugs and connected them to my pc and broadband with a ethernet cable. When i turn on my pc the ethernet light turns on (same for downstairs) but after installing the software and trying to search for my wifi a message pops up saying "The homeplug adapter has NOT BEEN DETECTED. Please check your computer cables". So i did so, i chnaged the sockect moved the ethernet cable to a diffrent slot and still it says it has not been detected. This is very annoying and i really want to get it fixed.
View 17 Replies
View Related
Aug 17, 2012
I recently factory restored my new PC and we also got a new Virgin Media Superhub (Super Fast - My dad is getting download speeds of up to 4mb/s) but I tried using my powerline adapter thingy and I am getting crappy speeds and it says I am connected to a homegroup, and not my internet like it used too.
View 1 Replies
View Related
Mar 11, 2011
I would like to set up a TV in my spare room which does not have a coax plug. Because of the set of my house running coax cable to this room, although possible, is something I am hoping to avoid. This is because if I was to run the cable on the outside of the wall it would get in my way and it will cost $300 to $400 for a tech to come out and run it through the wall.My first thought was to set up an old computer in my living room and have it connect to a cable box. Then I would send the video signal over the wireless network. The problem is that I cannot change channels on the other end. I have been reading up on power-line networking and it looks like a good option for my problem. I was hoping to find a device that will allow me to plug coax cable into it in the living room send the signal through the power-line to another device in my spare room where my TV receiver would be located. Is there anything like this out there on the market? If not are there any other options I can look at?
View 1 Replies
View Related
Feb 4, 2011
I'm planning to build a network in a office and I've decided to do that with powerline AV network adapters.I
1. what is the real limit of numbers of powerline AV adapters in one network?
2. what if my neighbours are planning to build their own network and total number of adapters in building exceeds the maximum possible number. How to filter powerline networks from each other?
View 5 Replies
View Related
Jan 3, 2013
I recently upgraded my wireless router to a Netgear R6300 and have had no problem with the wireless speeds,35mbps down and 6mbps up according to speedtest.net. I experience similar speeds from my direct wired connection as well but I am having an issue with my speeds running through my Linksys PLE300 powerline adapter I am getting speeds of 4mbps down and 6mbps up. My PC is running Vista Home Premium SP2 (I know). Prior to the upgrade I was using a Netgear N600 and I was getting much faster speeds through the powerline. My NIC is a Intel 82566DC -2gigabit. I checked all the cables, I am using a CAT6 from router to Powerline and when I run router stats it shows WAN as 1000M/full and LAN1 (powerline) as 100M/Full.
View 3 Replies
View Related
Jan 15, 2013
Unfortunately, my new PC is about as far away from the router as possible, which makes my wireless solution (£5 802.11n USB dongle) ineffective. I was looking into powerline Ethernet to solve this but then it occurred to me that my solar panels may interfere with its signal.Is this true? is it possible to get a strong wireless signal through 30m of stairs, walls and doors?
View 1 Replies
View Related
Jan 18, 2013
Is there an easy way to test the throughput speed of 2 powerline adapters? I want to know if they are underperforming so I want to rule out my router/internet in this test.
View 5 Replies
View Related
Aug 30, 2011
I have two netgear powerline AV 500 ethernet adapters that give me near ideal internet access on my media computer (FIOS 25/25mpbs tests out at 8ms 25.4/24.7) and perhaps 100-140mbps to my router, printer, drive, etc. I now want to add a few wifi points and instead of having the mess of a powerline adapter + a wifi router I think it will be neater to have an all in one solution. Most of the ones that I find are 200mbps, however. I know that 500 is backwards compatible, but will a mixed solution slow everything down like it can for a mixed wireless g/n network?
View 2 Replies
View Related
