I have a belkin N300 router that works decent most of the time, but anytime my roommate connects with her macbook pro the whole network becomes slow to the point of uselessness. If i block her computer using mac address filtering, the latency and download speeds are right where they should be, but as soon as i allow her back on ping jumps to 800-1000 and DL speeds drop to under 1mb.
View 1 RepliesThe main router is Belkin N300 and the new one is D-Link N300 DIR-651 for extended range.
View 1 Replies View RelatedI've just hooked up my previously used N300 router. The router is showing a solid green light, and the laptop recognizes that a solid Belkin wireless connection is out there. I cannot for the life of me remember the network key and/ or pass phrase I originally set. No, I did not tape this info to the underside of the router as suggested in Belkin instructions.
View 6 Replies View RelatedWe have 12 PC connected through a Switch(D-Link 10/100 mbps) with Configtured with Manual IP Address. the IP address range is 192.168.1.1 subnet mask 255.255.0.0 default gateway 192.168.1.1.Internet Cable Connected from Modem to Switch Directly & all the computer access internet by filling DNS with 202.56.224.153 other 59.144.127.17, We fill this DNS only where we want Internet access allowed by limiting that pc with Limited User access. How to configure Belkin Surf N300 Router with this network.
View 1 Replies View RelatedI have a belkin surf n300 usb wireless N micro adapter. No problems installing this adapter on a HP Desktop running windows 7. I have tried to install on a gateway laptop also running windows y 64 bit. In device manager it show that the product is working. It will not connect to any network. The adapter is an F7D2102 az ver. 2011az
View 2 Replies View RelatedAs per settings menu, I tried to give it an IP address but the new address is not accessible for further configuration. When I connected to the router it status changes to "unidentified network".
My primary network address range is 192.168.1.1 to 192.168.1.10. So I gave address to belkin as 192.168.1.100. But I can not access this address from both primary and belkin network.
Can I put more than one N300 Dual-Band Wi-Fi Range Extender on my home network?
View 4 Replies View RelatedFSD 7632-4 Router.Have this 2006 router which has started dropping the connection and/or slowing it down intermittently. Before I replace it, would like to update the firmware. Have downloaded the update but cannot log-in on the setup utility page as I cannot remeber my password (apparently it is not set to blank!).
View 1 Replies View RelatedAt the recommendation of a tech, I ran a speed test (speedtest.net) on my system with my N600 in place. The upload speeds averaged out to 0.21mbps. I took the router out of the system and the speed climbed to an average of 0.37. What is the problem with the router and what need I do to boost the upload speed with it in place?
View 1 Replies View RelatedI have a the aforementioned router set up with one PC laptop connected via ethernet cable and two to five other devices (PC laptops, iPhone, iPad, Linux Laptop) connected at any given time. About once or twice a week the router drops the network. I can still see the SSID, but can't connect on any device. The wired laptop gets dropped as well. I tried to ping its IP, but it says the device is unreachable. The only solution is to walk upstairs and unplug the router, which fixes it every time until a few days later when it happens again. I've restored factory settings a number of times.
View 8 Replies View RelatedCan't get internet.I can plug laptop directly into modem and works fine. When I plug modem into brand new wireless router (N300) the light glows amber. I've been through the set-up 10 times. Actually the same reason I replaced old router with this one.
View 2 Replies View RelatedWhy I cannot find "Wireless Bridging" under "Wireless" of my belkin n300. Its model is F9k1002v1.
View 2 Replies View RelatedI have two matching N300 Belkin routers. The cable modem feeds into modem1 and modem1 feeds into modem2. I get a good wireless connection on modem1. Modem2 shows up on a wireless scan and it accepts the password. It however will not connect.
View 1 Replies View RelatedThis morning I lost wifi connectivity. I reset the router and powered off and on the modem along with the router but to no avail. The blue stripe no longer shows on the top corner of the machine.I am able to connect to the internet using the ethernet ports on the router. I also tried to get into programming using 192.168.2.1 but it is timing out.
View 1 Replies View RelatedI'm trying to resolve an issue I've been having with Google Chrome. I've found a possible fix but i need to confirm the MTU settings on my router and was unable to locate the setting using the web interface for the router.
View 3 Replies View RelatedCan I set-up the N300 wireless router without a modem, this I want to use for wireless printer connections only for several PCs
View 2 Replies View Relatedmy neighbors cant pick up my signal unless they are outside. can i boost the signal from my router?
View 1 Replies View RelatedCan the Surf N300 be used as a WiFi repeater? Can the Surf N300 be used as a WiFi Access Point?
View 1 Replies View RelatedI have a belkin n300 and it whilst the modem itself is showing a static blue light, its coming up as an explanation mark on the wifi symbol on my macbook. This has been happening since yesterday when I was fiddling around with the settings on the IP address (192.168.2.1) to get the printer to work wirelessly which it did once then the wifi network went down.
View 1 Replies View RelatedIve Tried to use Facetime on my iphone 4 but connection does not go through I alost notice on my ps3 it noted NAT type 3 does this affect gaming online as well video conferencing?
View 1 Replies View RelatedCannot get wireless from any computers in home or room even the computer that I have installed the Belkin N300 on. When I click on the Belkin Icon on task bar get message "Wireless hardware not found" followed by comments about wireless radio not turned on and then how to recognize it with wireless radio icons. Now what do I do?
View 1 Replies View RelatedBelkin N300 - bought two weeks ago and have had very slow internet connection since.
View 1 Replies View RelatedI have a Belkin Surf N300 wireless Modem-Router, but cannot get it to connect to my Android phone. I can connect it to my Nexus tablet, to my desk-top and my lap-top, so I know there is nothing wrong with the router itself. Every time I try to connect the phone, it locates the network, scans, authenticates, but then says "Disabled" and the message: "Secured with WPA/WPA2 PSK" with "locked network" symbol. What does this mean? This is on the label that came with the router: "Security Type WPA/WPA2" but I don't know what to do in order to remove the lock. The phone is a Vodafone Smart Chat and I bought it specifically to be able to connect to Wi-Fi networks.
View 1 Replies View Relatedhow to change the password (security key) to limit who can use your wireless connection? I have the N300 wireless router.
View 1 Replies View RelatedI have a N300 f9k1002v1 router and would like to add guest access. Unfortuantely I can't find any info on how to do this. The user guide alludes to it but has no details. I also checked out this link: [URL]
since my router setp does not show "guest access" under "wireless" I skipped to #6 as stated. However when I get to #9 there is no "guest settings" dropdown for me to use.
I have a N300 router I would like to put in another part of my house to repeat the signal from my N600 at the other end of the house. Is this possible? If so, how do I set up the N300?
View 2 Replies View RelatedI just purchased a Belkin N300 and it's advertised as being able to video chat as well as have two computers connected to it. I can't even watch youtube videos with just one laptop connected because the ads take 5 minutes to load. Is this normal behavior for this router? Do I need to upgrade to be able to Skype?
View 2 Replies View RelatedN300 F9K1002v3 not loading some websites , other websites load just fine.Brand new just arrived yesterday afternoon.I have restarted the router.I have updated the firmware.I have reset the router by holding in the button on the back of the router. When I plug my computer directly into my modem everything works fine.
View 3 Replies View RelatedI purchased a Belkin N-300 router, model F9K1002V4, about 6 months ago, and recently upgraded my cable internet service to a 20+ mbps level, in hopes of improving the speed of my wireless devices. The speed on all of my wireless devices (a new laptop, ipad, and iphone) is still below 1mbps, even when I'm in the same room with the router. The speed on my wired computer registers above 20mbps, so I don't think the problem lies with the cable internet. I have tried to download the firmware update on Belkin's site, but my computer says it doesn't have the right program to run it, and it can't find the program on the web. I sent an e-mail to Belkin customer service, but they just sent me an automated reply, referring me back to their website, with the firmware update that I can't access.
View 4 Replies View RelatedThe instructions say to power off the modem but the modem is also for the phone and has a battery backup. How do i proceed? model N300 wireless router
View 1 Replies View RelatedI need to reset the channel on my N300 router but in order to do so, I need to log in. The log in screen does not take my existing password. How do I get my current password or reset my password? It should be the simplest thing, but I have found this to be extremely difficult with Belkin.
View 1 Replies View RelatedI can't find any parental control options on the sidebar but have read that it is an option with this modem-router.
View 1 Replies View RelatedMy N300 Wifi Range Extender does not let me connect to Internet. I can access other systems connected on the main WIfi network, but I cannot access Internet.I observe as well that all systems connected to the Extender appear, from the main Wifi network, having the same Mac address. I believe that my ISP (Telenet) does not accept that, and that this is the reason I cannot connect to Internet. Is there any way to change that behaviour ?
View 9 Replies View Related