Cabling / Cards :: Cannot Find 2x8pin PCI Express 2.0 Cable
Jan 19, 2011
I already have one 2x8pin PCI express power cable powering a GTX280 (along side its 6x6 pin cable). It has two male 8 pin ends (One is 6+2, the other is just 8).
I want to install my second GTX280 too but I only have a 6x6pin cable. I need a 8x8 aswell. The GTX280 requires one 6x6 and one 8x8 output. Where do I find one?
I CANNOT FIND ANOTHER 8+8 PCI EXPRESS CABLE ANYWHERE IN THE WORLD. Not EBAY, not any website on earth. Not my retailer or producer. ?
How else can i power the card properly? My PSU has no molex options. My PSU only accepts PCI express 2.0. My PSU is Everest 1200w with 4 of each type of socket.
View 2 Replies
ADVERTISEMENT
Jun 27, 2011
My Internet is down. I appear to be getting power from the modem as all the lights are lit up. I have a wireless router. On my desktop I clicked on the Network icon and it said "3WIRE***" is in range but requires a Network Key (also called a WEP Key or WPA Key)? Could this be the problem? I've never had to enter a password to access my internet before. Do you know how I can find (or reset) my password? It's a D-Link router.
View 2 Replies
View Related
Feb 18, 2012
My computer cannot find my Rosewill N PCI Adapter RNX-N360PC. I have used multiple slots on the motherboard, tried two adapters, and have reinstalled the software. the problem with software installation is that it cannot be installed because the computer can't find a driver. When i troubleshoot my internet connection, or my lack thereof, the problem is that "there is no adapter." How can i fix this?
View 1 Replies
View Related
Apr 10, 2013
I recently installed the above wireless card, but I can't get it to work. Under the Device Manager, it has this error:This device cannot find enough free resources that it can use. (Code 12)If you want to use this device, you will need to disable one of the other devices on this system.I've tried updating the driver, and disabling the little USB wireless device I was using before, but I still can't seem to get it working. [code]
View 9 Replies
View Related
Jan 13, 2013
I'm installing a wired network in the office, going to upgrade from a cat 5 to a cat 6. My question is cat 6 cables clipped same as cat 5 using same rj45 clips? And is coloring same, am going wg-g wo-b wb-o wbr-br.
View 1 Replies
View Related
Sep 7, 2011
I'm having an issue with my network adapter. It's not detecting the Ethernet cable, thus not able to connect to my home network. The trouble shooter (Windows 7 home 64) says it canning detect the cord. But the cable works fine on my other computer. The network adapter is a Nvdia nforce networking controller. All the drivers are up to date. The computer was completely formatted so it's a blank slate
View 8 Replies
View Related
Sep 11, 2012
I recently performed a windows 7 update and when I opened my computer the next morning, the wifi wouldn't work. All the other computers in the house work, but this one. The switch is turned on, have checked device manager and NOTHING is listed there. The green light won't even come on when the switch is activated. I am not computer literate, but have resorted to everything except cleaning the system and rebooting. I am currently using a usb wifi adapter?
View 5 Replies
View Related
Dec 5, 2012
I am trying to connect CAT5e riser cable to a GE #76536 network and phone wall plate.The problem I am having is the CAT5e cable has 4 twisted pairs of wires as follows: blue/white, green/white, orange/white and brown/white. The wall plate connection has 8 distinct colors; blue, white, green, orange, yellow, black, red and brown. (or at least that's what they look like to me)None of the white wires from the CAT5e cable have any striping. They are all solid white. I've found color charts for matching striped wires, but I am at a loss to figure out how to connect these white wires to the proper terminals
View 7 Replies
View Related
Apr 3, 2012
I can connect to the internet using my neighbors wireless router but when I try to use my ethernet cable it connects me to "network 16" but the internet doesnt work. Ive tried different cables and different wall ports and that didnt work. It has been working before but I disconnected it to go somewhere and when I came back I had this problem. I use Windows 7 and Im trying to connect using Marvell Yukon 88E8057 PCI-E Gigabit Ethernet Controller.
View 8 Replies
View Related
Jul 24, 2011
i reformatted my computer 1 month ago, when i try to connect with ethernet cable it doesn't connect, but when i use the usb cable which i got with my modem it connects.btw i have a acer e389 which runs on XP(media center).
View 9 Replies
View Related
Dec 12, 2012
Ive been using an Ethernet cable to connect to the Internet for a while now, it was working fine up to yesterday where I left my desktop open for a few hours and came back to find that I have no Internet connection.
I used my laptop to test the cable out and it works fine, the wireless works fine too. There doesnt seem to be anything wrong with the modem since I still have Internet on the PS3. I used a different cable to test the modem again with my laptop and I had internet access. The desktop is still connected to the modem but it only gives me a network connection with no Internet.
I tried restarting the modem but it still wouldnt work and I also tried to disable then enable the connection.
Im using Realtek PCIe GBE Family Controller with the latest driver.
View 16 Replies
View Related
Apr 12, 2011
Can't log on to computer running win xp sp3. I'm getting message that ethernet cable is unplugged but it's not unplugged. The modem/router was installed by Verizon (for FIOS connection) in February 2011. Internet was working fine until a couple of days ago. I have looked at other posts on this issue but have found nothing that would solve the problem. My old dial-up modem was still installed in the computer and had a question mark on it in device manager so I removed it. I thought maybe there was an IRQ conflict as the modem used to use IRQ 11 and the network card (linksys) uses that sometimes as well as IRQ 10 but that didn't work.
View 19 Replies
View Related
Aug 3, 2012
Computer keeps saying that the I need to plug in a ethernet cable but I already did. This is happening on my Windows 7 Ultimate partition. I also have have a Mac OSX partition and the internet is working fine on that partition.Here is what I get for ipconfig/all command:[CODE]
View 18 Replies
View Related
May 4, 2011
What can I do?
View 6 Replies
View Related
Sep 12, 2011
I am having a problem where I can't connect through a cable. I running on Windows XP SP2. My comp. is a HP Pavilion a1483w. I have just reformatted it.
View 3 Replies
View Related
May 16, 2011
I have Cordata 5e cable and noticed the wires inside are not the typical wire colors ie:green/ white. The colors of wires are all solid ie: green, yellow, tan, pink, etc...
View 1 Replies
View Related
Feb 9, 2012
easiest way to convert a cat 5e crossover cable to make it a straight? I have 2 PCs networked & am introducing a router & need to covert the cable without having to rewire it if possible.
View 1 Replies
View Related
May 19, 2012
I just bought a 30m CAT6 cable which I installed inside the house, now since my router is on the floor above me I bought a 30m cable to be able to have it downstairs. I don't really know if it has something to do with the PC or if it is the length of the cable that is the problem. But when I try the PC on the main floor the speed is 15-20mbit/s and when I try it on my PC downstairs, all I get is a maximum of 10mbit/s. The strange thing is that ping/jitter is the same both upstairs and downstairs?
View 5 Replies
View Related
Jul 28, 2011
I am designing a cabling system to interconnect all the buildings in my school.In one of the building, I have 2 patch panels and switch to interconnect cables that comes into the building with cables that runs to the rooms.From what I understand, connectivity should be something like this:
1. Exterior cables coming in through the entry point.
2. Exterior cables terminates at the back of patch panel.
3. Patch cables run from the front of patch panel to a switch.
4. Patch cables run from the switch to another patch panel which connects the interior cabling that runs to the wall socket in each room.
My question:
1. Which ports should I use on the switch to interconnect exterior cable to the interior cable? They should be a connection between the exterior cabling and the interior cabling and both terminates in the same switch, but different ports. How do you allow communication to happen?
2. How do connect all the buildings to the router that connects to the internet?
View 2 Replies
View Related
Aug 15, 2011
I have a printer (epson cx6600) I wanted to connect to our router here so everyone can print to it. It only has a usb connector (which you would typically connect to your pc)... I did notice they have usb to lan cables out there and was going to buy one and connect it to the router that way.
View 1 Replies
View Related
Jan 28, 2012
can i connect a cat6 cable to a cat5 wall jack
View 1 Replies
View Related
Jan 30, 2011
Everytime i plug the cable into my PC it doesn't detect it and the helper says to insert an ethernet cable.When I go to network sharing centre and check my connections it says network adaptor unplugged.im using wireless at the moment.My pc is a packard bell ipower x9810. it was windows vista but i upgraded to windows 7, i checked the packard bell website and can't find any networking adaptors. I have also checked device manager and it says - Belkin N+ wireless USB adapter #4 NVIDIA nForce 10/100/1000 Mbps Ethernet. there is no yellow exclamation mark.
View 17 Replies
View Related
Mar 1, 2011
A few days ago, I noticed that my computer wasn't picking up my wired connection anymore while the wireless connection was still working fine. I opened up my network adapters and my Local Area Connection adapter wasn't even showing anymore, only the Wireless adapter. I updated my drivers, tried different cables and even a different router but still no dice. This morning, when I booted up my system, Windows said it was installing driver software for Broadcom Gigabit Ethernet Controller. I got really excited when I saw Local Area Connection in my adapter menu and plugged in my ethernet cable. Nothing happened and my laptop refuses to recognize the ethernet cable plugged in to it. It's a Dell XPS 1640, Windows 7 x64 with Service Pack 1.
P.S. Usually a little orange light appears in the ethernet port on my computer when a chord is plugged in. When I turned on my computer this morning with the chord in, the light was on. When Windows finished booting, the light went off.
View 6 Replies
View Related
Aug 13, 2012
i am having a problem with my desktop right now, just recently i re-installed Windows7, a clean format... but then i suddenly noticed that i cant connect to the internet, no network adapters are detected on the Network Connections, its empty i looked at the Device Manager and saw a yellow warning on realtek rtl8139/810x family fast ethernet nic, i download the driver using my laptop (wireless connection)... and installed that driver on my desktop pc then checked the device manager once again, but it still has a yellow warning.i dont know what to do anymore, and at the last screenshot theres this error message: This device cannot find enough free resources that it can use. (Code 12) If you want to use this device, you will need to disable one of the other devices on this system.i have two lan cards, one at the motherboard(not in use) and the other PCI-E lan card (tp-link ) ...im just wondering if that Realtek i just installed is the lan driver for the motherboard?
View 2 Replies
View Related
Mar 13, 2011
I have only windows computers at home, although for some reason i recently bought an Apple Airport express. Probably because its a lot faster than the old router Ive got now. But I have a problem when i try to set it up. When I plug in the Express and the cable from the cable modem then start Airport utility, it cant find the Express. Ive tried using my laptop and connecting it straight into the modem, but that doesn't seem to fix anything.
View 1 Replies
View Related
Sep 8, 2012
I've got on-board LAN but I don't know how to use it. Am I meant to be able to surf the internet just like that if i have got on-board LAN???
View 3 Replies
View Related
Apr 29, 2012
My hard drive crashed and had to reinstall my OS using manufacturers disk now everything works but the internet, the integrated ethernet card is not listed under network adapters in the device manager, its a clean install of windows xp media center edition 2005 sp2, the device manager shows no drivers missing.
View 5 Replies
View Related
Sep 17, 2012
i am using win7 64 bit on dell n5110 and my lan is not working properly. it wont even detect the cable . when i plug in the cable its like nothing happened. but when i uninstall and reinstall the driver, it sometimes resolves the issue. but i have to do this every time.
View 3 Replies
View Related
Aug 1, 2012
I have an Eee-PC and im trying to connect to the internet via my HUAWEI E173 MOBIEL INTERNET STICKWhen I plug it in it reds it, but only like a mass storage device.
View 3 Replies
View Related
Jul 6, 2012
I have network: 20 PC's conected to a switch (ordinary switch), from switch to a router (for DHCP and internet conection), Router is connected to a cable modem.
Lately an issue arised. One PC started having problem witch connection (PC is windows 7, up to date). PC instead of 192 addres is getting 169 (i need to highlight it is a problem with only one PC). That means the PC is connected to the Router but it is not getting proper IP addres. After changig the addres to static the connection ws fine for few days and then in networc connection icon (botom right) it came up with 'unidentified network' message. I changed the patchleeds, even changed the connection with known working line (from outlet to patchpanel) and the connection was coming and going. Then I changed network card with the same resoult. I noticed strange thing: While the IP is 169 or when 'unid net' when I unplug the cable from outlet then plug back and do so couple times in one moment the connection is back and stable but only for some period of time. Cables had been re terminated with new jacks and at the patch panel. Drivers for network card are up to date.
Why is the connection coming and going?
View 3 Replies
View Related
Nov 3, 2011
I'm currently volunteering at a children's group near me. They've just moved offices and are wanting a computer network in place. I have quite a bit of experience with hardware and software troubleshooting, but anything past the server is beyond me.They have a telecommunications box, as many places do, and the box has a set of patch boxes that are, according to the telecommunications people, plugged in and good to go. Each office has tunnelling on the wall with network sockets, again the norm.
View 4 Replies
View Related
Jun 23, 2012
I have found a great application that allows your PC to become a hotspot. It can also protect the wi-fi. Now remember whatever its your backend on the PC is what kind of network and speed you get such as, if my desktop connected through ethernet and I install the virtual router on the desktop than my laptop can connect to it depending on my Wi-Fi adapter on it. It could be B/G/N. B and G gives 54MBPS and N gives me 65MBPS.
View 1 Replies
View Related
Jun 6, 2012
Can I use ONE wireless usb adapter for two computers? Of course not at the same time but I was wondering if it is possible? Also, do I need to have the disc to install it or will the 2nd computer I want to use the wireless usb adapter for prompt me to install the software when I put it in the usb drive? I have misplaced the cd the usb adapter came with which is why I am askinit is a laptop and I know I can use ad hoc but I am trying to set up wireless on that laptop without ad hoc.
View 2 Replies
View Related