Cabling / Cards :: Can Connect A Cat6 Cable To A Cat5 Wall Jack
Jan 28, 2012can i connect a cat6 cable to a cat5 wall jack
View 1 Replies
ADVERTISEMENT
Will Type Of Cable (cat5 / Cat6) Increase Internet Speeds
Jun 7, 2012at my house if i replaced a cat5 cable with a cat6 would i see increased download speeds?
View 5 Replies View RelatedCabling / Cards :: CAT5 Ethernet Cables Not Working
Jul 14, 2011I live in a frat and I am currently researching how to design and configure the most efficient network for the house. However, one of the other big problems we have is connectivity of our ethernet cables. We have an IT room with 2 switches that feed ethernet cables to all parts of the house and connect to an ethernet box in the wall where we can simply wire in our internet connection. We have wireless routers too but to keep the bandwidth usage across the WAP's I want to let people use the wired connections. However, many of the connection in the house do not work at all. I plug in my laptop to the wall jack and it gives me the No Internet Access notice. I don't understand why it works in some rooms and not others. All jacks seem to go into the same switches at the other end so I cannot figure out what the problem could be.
View 2 Replies View RelatedCabling / Cards :: Cat5 Not Working Past 25Ft
May 22, 2012We are setting up a network in our new house. We have the internet entering the garage. From there we have a 60 ft Cat 5 cables run through the crawl space. Orginally we had the wireless router attached to the end of the cat 5 and then attached to the computer. We could not get a connection through this wire. We then took out the cable, and ran a new one, same issue. We took the same cable, cut it down to 25 feet, installed the router in the garage and we have an excellant connection. We then ran a new wire through the crawl space from the router. Same issue, no connectivity. Taking that cable out, cutting it down we ran the wires from the router to our computers in the garage. why a Cat5 cable would not work at 60Ft.?
View 6 Replies View RelatedPhone Jack Wiring For DSL First Jack Through Outside Wall?
Dec 18, 2011I received Centurylink DSL modem with hardware but my phone jack wiring was ripped out of wall,no wiring intact.what kind of jack and how to wire them to the jack. The wiring came thru wall are new kind with 4 pairs and have stripes on them.
View 1 Replies View RelatedCabling / Cards :: CAT6 Cables Suddenly Not Working?
Dec 11, 2012Recently encountered this problem where one cable suddenly not working properly.We are using 568B as our standard cabling here, lines 1,2,4,and 5 are working as of checking,but lines 3,6,7, and 8 are not. Before it was working flawless. The cable are buried underground inclosed in a pvc hose.
View 11 Replies View RelatedCabling / Cards :: How To Connect CAT5e Cable To GE Wallplate
Dec 5, 2012I am trying to connect CAT5e riser cable to a GE #76536 network and phone wall plate.The problem I am having is the CAT5e cable has 4 twisted pairs of wires as follows: blue/white, green/white, orange/white and brown/white. The wall plate connection has 8 distinct colors; blue, white, green, orange, yellow, black, red and brown. (or at least that's what they look like to me)None of the white wires from the CAT5e cable have any striping. They are all solid white. I've found color charts for matching striped wires, but I am at a loss to figure out how to connect these white wires to the proper terminals
View 7 Replies View RelatedCabling / Cards :: Cannot Connect To Internet Using Ethernet Cable
Apr 3, 2012I can connect to the internet using my neighbors wireless router but when I try to use my ethernet cable it connects me to "network 16" but the internet doesnt work. Ive tried different cables and different wall ports and that didnt work. It has been working before but I disconnected it to go somewhere and when I came back I had this problem. I use Windows 7 and Im trying to connect using Marvell Yukon 88E8057 PCI-E Gigabit Ethernet Controller.
View 8 Replies View RelatedCabling / Cards :: Can't Connect To Internet With Ethernet Cable?
Jul 24, 2011i reformatted my computer 1 month ago, when i try to connect with ethernet cable it doesn't connect, but when i use the usb cable which i got with my modem it connects.btw i have a acer e389 which runs on XP(media center).
View 9 Replies View RelatedCabling / Cards :: Cannot Connect To Internet Through Ethernet Cable
Dec 12, 2012Ive been using an Ethernet cable to connect to the Internet for a while now, it was working fine up to yesterday where I left my desktop open for a few hours and came back to find that I have no Internet connection.
I used my laptop to test the cable out and it works fine, the wireless works fine too. There doesnt seem to be anything wrong with the modem since I still have Internet on the PS3. I used a different cable to test the modem again with my laptop and I had internet access. The desktop is still connected to the modem but it only gives me a network connection with no Internet.
I tried restarting the modem but it still wouldnt work and I also tried to disable then enable the connection.
Im using Realtek PCIe GBE Family Controller with the latest driver.
Cabling / Cards :: HP Pavilion A1483w / Can't Connect Through Ethernet Cable
Sep 12, 2011I am having a problem where I can't connect through a cable. I running on Windows XP SP2. My comp. is a HP Pavilion a1483w. I have just reformatted it.
View 3 Replies View RelatedCabling / Cards :: (epson Cx6600) Connect A Printer To Router Using A Usb To LAN Cable?
Aug 15, 2011I have a printer (epson cx6600) I wanted to connect to our router here so everyone can print to it. It only has a usb connector (which you would typically connect to your pc)... I did notice they have usb to lan cables out there and was going to buy one and connect it to the router that way.
View 1 Replies View RelatedCabling / Cards :: Belkin N+ Wireless USB Adapter / Can't Connect To The Internet With Ethernet Cable
Jan 30, 2011Everytime i plug the cable into my PC it doesn't detect it and the helper says to insert an ethernet cable.When I go to network sharing centre and check my connections it says network adaptor unplugged.im using wireless at the moment.My pc is a packard bell ipower x9810. it was windows vista but i upgraded to windows 7, i checked the packard bell website and can't find any networking adaptors. I have also checked device manager and it says - Belkin N+ wireless USB adapter #4 NVIDIA nForce 10/100/1000 Mbps Ethernet. there is no yellow exclamation mark.
View 17 Replies View RelatedHow To Set Up Router / Have A Jack In Wall Says Cat5e
Dec 14, 2011SO I am not a computer wiz... but I have this outlet in my upstairs wall which has a phone and Cat5e Jack. I would like to set up my wireless router up there but where does the modem go? there is no jack for the cable.
View 1 Replies View RelatedT568B Wall Jack Wiring?
Jan 4, 2011I'm wiring up the house with CAT6 (I've never done this before). Someone told me to use 'T568B' termination. Every configuration I see on net looks different, and I'm getting confused.
The jacks have double colour coding for each wire as pictured here:I take it 'A' is for T568A, and 'B' is for T568B?So this is how I should arrange the wires for T568B:
Hooking Up DSL Through CAT5 In The Wall?
Nov 15, 2011I have CAT5 cables run throughout my house to a few different jacks. They plug into my modem downstairs. I want to hook up my desktop internet through one of the wall jacks upstairs. The wall jack has CAT5 cable run to it but only accepts telephone wire sized jacks. How do I connect to the internet with this setup?
View 14 Replies View RelatedRunning Cat6 UTP In Same Wall Cavity
Mar 8, 2013I have done similar with cat5e in the past, but only operating at 100mb/s. The gigabit stuff I have done so far has had the power in a separate stud cavity.My structured wiring project will be installed in one stud cavity in the soon to be new home office. Not exactly using a structured wiring cabinet, but rather using a 7u wall mount relay rack bracket. The cabling will be entering using 2 separate header penetrations. One existing just inside on the right side of the stud cavity carries 110V 12/2 romex to a stud attached box / recepticle. The other side gets the new penetration, a minimum of 12" away. That's the one that the ethernet cable will pass through. The cable runs will run through the wall and through a brush plate, and then to the patch panel.
The Cat6 cable is UTP, and is marked for in wall use. This is the stuff with the spline if that matters.The romex, by code MUST be attached to the stud, and it is, the cat6 on the other hand is allowed to be loose in the wall. I do not plan on having enough slack in the wall for the cat6 to ever get closer than 8" from the romex, and no closer than 10" from the electrical box.Is that separation sufficient to avoid inductive noise on the ethernet cables? Like I said, I have done similar with Cat5e and no problems ever, but only attached to 10/100 networks. I can change stud cavities, but would rather stick with the one so that my ethernet, and power both can enter the rack cleanly.
Terminate CAT6 Home Runs With Male RJ45 Or Female Keystone Jack?
Jul 8, 2013I'm going to be running CAT6 throughout my house (once I figure out all the paths and buy the cable) with the home runs going to a patch panel in the basement.
I've been wondering if I should terminate each cable with a male RJ45 end and use a patch panel with RJ45 female-female keystone couplers or; terminate each cable with a female RJ45 keystone jack and snap it into a keystone patch panel.
I'm just wondering if there are any pros and cons to each, each method seems to be exactly the same, just buying different pieces.
Cabling / Cards :: Is Clipping Cat 5 And Cat 6 Cable The Same
Jan 13, 2013I'm installing a wired network in the office, going to upgrade from a cat 5 to a cat 6. My question is cat 6 cables clipped same as cat 5 using same rj45 clips? And is coloring same, am going wg-g wo-b wb-o wbr-br.
View 1 Replies View RelatedCabling / Cards :: Can't Detect Ethernet Cable?
Sep 7, 2011I'm having an issue with my network adapter. It's not detecting the Ethernet cable, thus not able to connect to my home network. The trouble shooter (Windows 7 home 64) says it canning detect the cord. But the cable works fine on my other computer. The network adapter is a Nvdia nforce networking controller. All the drivers are up to date. The computer was completely formatted so it's a blank slate
View 8 Replies View RelatedCabling / Cards :: Cannot Find 2x8pin PCI Express 2.0 Cable
Jan 19, 2011I already have one 2x8pin PCI express power cable powering a GTX280 (along side its 6x6 pin cable). It has two male 8 pin ends (One is 6+2, the other is just 8).
I want to install my second GTX280 too but I only have a 6x6pin cable. I need a 8x8 aswell. The GTX280 requires one 6x6 and one 8x8 output. Where do I find one?
I CANNOT FIND ANOTHER 8+8 PCI EXPRESS CABLE ANYWHERE IN THE WORLD. Not EBAY, not any website on earth. Not my retailer or producer. ?
How else can i power the card properly? My PSU has no molex options. My PSU only accepts PCI express 2.0. My PSU is Everest 1200w with 4 of each type of socket.
Cabling / Cards :: Ethernet Cable Unplugged Message But It's Not
Apr 12, 2011Can't log on to computer running win xp sp3. I'm getting message that ethernet cable is unplugged but it's not unplugged. The modem/router was installed by Verizon (for FIOS connection) in February 2011. Internet was working fine until a couple of days ago. I have looked at other posts on this issue but have found nothing that would solve the problem. My old dial-up modem was still installed in the computer and had a question mark on it in device manager so I removed it. I thought maybe there was an IRQ conflict as the modem used to use IRQ 11 and the network card (linksys) uses that sometimes as well as IRQ 10 but that didn't work.
View 19 Replies View RelatedCabling / Cards :: Computer Can't Detect Ethernet Cable?
Aug 3, 2012Computer keeps saying that the I need to plug in a ethernet cable but I already did. This is happening on my Windows 7 Ultimate partition. I also have have a Mac OSX partition and the internet is working fine on that partition.Here is what I get for ipconfig/all command:[CODE]
View 18 Replies View RelatedCabling / Cards :: Computer Doesn't Recognise WLAN Cable?
May 4, 2011What can I do?
View 6 Replies View RelatedCabling / Cards :: Cat5e Cable Wrong Wire Color?
May 16, 2011I have Cordata 5e cable and noticed the wires inside are not the typical wire colors ie:green/ white. The colors of wires are all solid ie: green, yellow, tan, pink, etc...
View 1 Replies View RelatedCabling / Cards :: Convert A Cat 5e Crossover Cable To Make It A Straight?
Feb 9, 2012easiest way to convert a cat 5e crossover cable to make it a straight? I have 2 PCs networked & am introducing a router & need to covert the cable without having to rewire it if possible.
View 1 Replies View RelatedCabling / Cards :: ADSL Speeds Slower With Long Cable?
May 19, 2012I just bought a 30m CAT6 cable which I installed inside the house, now since my router is on the floor above me I bought a 30m cable to be able to have it downstairs. I don't really know if it has something to do with the PC or if it is the length of the cable that is the problem. But when I try the PC on the main floor the speed is 15-20mbit/s and when I try it on my PC downstairs, all I get is a maximum of 10mbit/s. The strange thing is that ping/jitter is the same both upstairs and downstairs?
View 5 Replies View RelatedCabling / Cards :: Switch To Interconnect Exterior Cable To Interior One
Jul 28, 2011I am designing a cabling system to interconnect all the buildings in my school.In one of the building, I have 2 patch panels and switch to interconnect cables that comes into the building with cables that runs to the rooms.From what I understand, connectivity should be something like this:
1. Exterior cables coming in through the entry point.
2. Exterior cables terminates at the back of patch panel.
3. Patch cables run from the front of patch panel to a switch.
4. Patch cables run from the switch to another patch panel which connects the interior cabling that runs to the wall socket in each room.
My question:
1. Which ports should I use on the switch to interconnect exterior cable to the interior cable? They should be a connection between the exterior cabling and the interior cabling and both terminates in the same switch, but different ports. How do you allow communication to happen?
2. How do connect all the buildings to the router that connects to the internet?
Cabling / Cards :: Broadcom Gigabit Controller Won't Recognize Cable (Dell XPS 1640)
Mar 1, 2011A few days ago, I noticed that my computer wasn't picking up my wired connection anymore while the wireless connection was still working fine. I opened up my network adapters and my Local Area Connection adapter wasn't even showing anymore, only the Wireless adapter. I updated my drivers, tried different cables and even a different router but still no dice. This morning, when I booted up my system, Windows said it was installing driver software for Broadcom Gigabit Ethernet Controller. I got really excited when I saw Local Area Connection in my adapter menu and plugged in my ethernet cable. Nothing happened and my laptop refuses to recognize the ethernet cable plugged in to it. It's a Dell XPS 1640, Windows 7 x64 with Service Pack 1.
P.S. Usually a little orange light appears in the ethernet port on my computer when a chord is plugged in. When I turned on my computer this morning with the chord in, the light was on. When Windows finished booting, the light went off.
Connect Cat6 Cable From Ext Nte To ADSL Nexuslink 5631 Router?
Feb 28, 2013I am trying to connect a cat 6 cable from the Ext Nte to the adsl nexuslink 5631 router but i couldn't make the router works for the 2 line i only get one line led on i tried to change the wires colors on the rj11 (4 pins) and even so i cloud not get both led light goes on for tho line and this only for the cat 6 if i hook the old wire i dont know whats kind of wire i think its for inercom or mebe cat3 its works in the ext Bt only 2 wires connected and on the modem side 4 wires is o nthe rj11 plug i tried to do it the same way with cat6 i only get single line and i do it now with (white-orange=pin 1) (blue-white=pin 2) (white-blue=pin 3) (orange-white=pin 4 ) on the plug , on the bt side i tried to but white -blue with blue-white not working even the opposite.i just want to know how to wire from ext-Bt to router using rj11-4pin cua thats what my router use on bonding to lines, btw i have only 2 wire on the bt side because i got 2 line phones on a phone line in the bt?
View 5 Replies View RelatedCabling / Cards :: Can't Connect To The Internet Eee-PC?
Aug 1, 2012I have an Eee-PC and im trying to connect to the internet via my HUAWEI E173 MOBIEL INTERNET STICKWhen I plug it in it reds it, but only like a mass storage device.
View 3 Replies View RelatedCabling / Cards :: Not Able To Connect To Internet
Apr 1, 2013I have a fee pcs at home...all are able to connect to the internet but theres only one thats not able to...the network and connection centre keeps and changing from identifying to not connected. The cable itself is fine.
View 13 Replies View RelatedCabling / Cards :: New PC Won't Connect To Internet
Dec 30, 2011I can open files, play videos, run programs, etc. Windows installed without a problem.However, I can't connect to the Internet. At all. I can't even register my version of Windows because I can't contact Microsoft for verification, because the connection won't get through. No Internet devices can be detected.That was with a long cable wired directly to our router, which is next to our modem.So, today, I bought a D-Link Xtreme N Desktop PCI adapter to connect. Still no connection... I don't think the PC even detects the adapter, because the drivers coming with the adapter can't detect it, and the light on the adapter doesn't turn on.That shouldn't happen. Both the cable and adapter go directly into the motherboard. My operating system is Windows 7 Ultimate 64-Bit, and my motherboard is an Asus P8Z68-V PRO.My ISP is Cogeco. All other computers and wireless devices in the house work perfectly fine.
View 2 Replies View Related