Cisco ISE 1.1.3 is running in standalone mode, when I made any configuration it show me the notification that "Configuration changes has been recorded but remain pending" .
View 1 RepliesACS 5.2 , in my Primary ACS under System Administration > Operations > Distributed System Management I see my Secondary but it shows "PENDING" under Replication Status.
View 3 Replies View RelatedI am using the router DIR-825 together with a modem-router DSL-526B. After reading many posts, I understand that I have to bridge the DSL-526B and use the more complete DIR-825 under PPOE to connect to Internet. However, when bridging the DSL-526B, the settings are showing after setup that the firewall and NAT are enabled whereas, when looking at the quick bridging setup in the manual, it seems that they should be disabled. My questions are therefore:
In bridging mode, can the firewall and NAT remain enabled, what can possibly create a conflict with those of the DIR-825 or create complication? If yes, how to disable them, as no option for doing it in the briging quick set up?
My PC is hardwired to a Comcast all in one Internet/Phone Modem/Wireless Router. I have installed new software on my Android Phone that can control my music recording software over Wi-Fi. Here is the rub: Recording software and the Internet don't play nicely together. They are in constant conflict for resources. I used to simply disable my network connection when working in my recording software. This obviously won't allow my phone to connect to my computer . Is there a way to disable my Internet connection yet remain connected to my network? I don't want to disable the entire networks Internet connection since there are other Internet users on the network.
View 5 Replies View RelatedI have just purchased 3 DCS-932L'S and installed 3.11 D-ViewCam software. I have done my best to configure the mainconsole correctly so that my cam's will record on motion based occurances on a weekly schedule of 24 hours a day everyday. I have a lot of evidence that the system is recording as when I have the console open that there is motion detected and there are 3 folders in my nas unit that has tons of .dat files in them. My problem comes in when using the playback system. When I select the search by date/time button and locate the folder that is for a the camera I am interested in playing video for the results never show up!
View 1 Replies View RelatedI have latest 3.3 dlink d-view cam software and a dcs-932l ip camera.I noticed the remote streaming and remote recorded viewing (ports 5150 and 5160) as part of the server software. I know if i browse to my ip of my pc it allows me to view both services on html via windows plugin visual basic addon. My question is what iOS app and Mac OS X app will allow me to remotely monitor my dviewcam softwares network service for both live view and recorded view.
View 1 Replies View RelatedI have fresh installed the LMS 3.2.1 without any errors. Then I am adding device in CS, give it correct credentials. Its appears in RME automatically, but it always remain in Pending devices in RME.
I have run a job in RME to check the devices credentials and it's appearing that credentials for snmp are wrong but ssh/ telnet appears as "did not try". Although I have added the correct credentials in CS for device, but it appearing as wrong in RME.
Also when I add device in CS, it's not automatically picking it's device type, until in CS I define its device type manually.
I had a problem with my laptop ICS.
1 Acer laptop with windows 7 home premium
1 MSI laptop with windows 7 ultimate
1 Hp Netbook with windows 7 starter
1 USB Broadband
First i had connect the USB Broadband using by acer laptop to make as wifi router/wifi host via ad hoc.MSI laptop and Hp Netbook was successfully connected and able to connected to the internet which share from Acer laptop.Second, after that i am trying to use MSI laptop to create as wifi router/wifi host just like the same way what i done with Acer laptop.My both Acer laptop and Hp Netbook successfully connect to MSI laptop but only the Acer laptop was unable to connect to internet and it was showing "No Internet access". and the "homegroup something it showing "Unidentified network" on the MSI laptop.I had tried to restart all the laptop and netbook to resetting it, unlucky it still unable to connecting to internet.Also i had set all to "Obtain an IP address automatically".And i found out that my laptop ICS on service didnt starting and on Firewall didnt have ICS on the list.When i try to click the start buttom it popping out this:"The Internet Connection Sharing (ICS) service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs"
Running 5 PC's and a laptop on a wired/wireless network at home. One PC running Win XP Pro started dropping the network connection (so it appeared) during browsing. Have found the following:
1. MSN messenger runs fine, and doesn't drop out
2. AVG antivirus updates with no issues
3. Web Pages in Chrome and IE will load fine one minute, then cannot load or pause for 1-2 minutes while loading
4. Can ping web addresses/IP addresses from command prompt with no issue.
5. Have changed the network connection from Ethernet to Wireless, which makes no difference to the issue.
6. If I "repair" the connection, and the network refreshes the IP address, I can browse successfully, for about a minute, before the issue occurs again. "Repair connection" again and can browse again for a minute.
7. Checking connected devices to the Netgear router, shows the PC name sometimes, against the IP address, other times it shows the PC as "unknown" against the PC address (when this occurs, web browsing is lost)
8. All other PC's on the network are fine.
I'm trying to get my wife's new 'All Fine 7" netbook Windows' connected via wireless connection. I had a muted attempt at it but so did my daughter and her boyfriend. I've got as far as it saying 'connected' but as soon as it does I get a message; Error from RasDial. I think I have created some conflicts perhaps! In the control panel I have done the following:'Internet options' under 'Connection' I've highlighted 'USB 'Network & Dial-up connections I have a choice of 'My connection' 'Main Computer' 'RT28701' & 'ENC28J601' The connection I have so far seems to be using the RT28701.My other option to 'USB is to select 'Desktop @ 19200' but that didn't seem to work either.
View 9 Replies View Relatedim intending to setup a small office network through a sever at my work and would like to know if it is possible to have the network running with each pc having its own internet connection.in theory this should work by having the internet connected via usb which will leave my ethernet ports free for the network..i would just like to know if this route will work just like that or will i need to have a rethink.
View 13 Replies View RelatedBrand new MSI system using windows 7. we're using a wirless network in the house, and up until today it's been fine. Randomly, Windows is no longer detecting any networks.
I've confirmed there is no prob with the router or signal as I can detect the network in my room and connect to the internet (using a homeplug hardline). I've tried enabling and disabling both the router and wireless card, a system restore (windows made no changes), and when I came to use the windows 7 troubleshooter - it says the device is not enabled?
Okay, so our old computer took a dump & our friend rebuilt us a new one and he threw in a new router to go with it. Its a D-Link router, which is directly connected to our desktop. However, upon completion of a new desk installment, we put the router into the cabinet and my gateway laptop immediately stopped being able to connect to the internet or the router at all.
1) The router is connected to the internet and broadcasting.
2) I've reset and refreshed the router and my window of available networks on my laptop, which did not work.
3) I've pulled it out of the cabinet, which also had no affect.
4) I did a manual search for the router, and it says the network already exists and asks if i would like to connect and upon agreeing to this, it returns me to the page of available networks, which does not include my router.
i have recently added to a domain. The initial setup is a server running windows 2003 and several xp machines which logon to the domain using mandatory profiles. However, after adding windows 7 machines and logging them on to the system it doesnt load the profiles. (which is fine as I understand you cannot use the same profiles with windows 7+xp)The problem is it automatically creates a roaming profile when logging off and saves it back to the same path as the other profiles under user.V2 which is growing considerably and causing huge logoff and logon times.How can I get the windows 7 machines to not attempt roaming profiles back to the server and instead to just save the profiles locally when logging off.
View 14 Replies View RelatedAny good link to find how to configure MAB table on acs 5.3? I cannot find one by myself. If it is possible a guide with picture in it.
View 7 Replies View Relatedstep by step ACS 5.1's basic configuration through CLI?
View 2 Replies View RelatedHow to backup the configuration on cisco acs 5.2 and how to restore it , if some thing wrong happened
View 7 Replies View RelatedI need to configure RADIUS VSA configuration for a my alvarion device. Following are the attributes that need to be configured.
- Packet Data Flow ID (ID 1, integer16)
- Direction (ID 4, integer8)
- Transport Type (ID 6, integer8)
- UplinkQoSID (ID 7, integer8)
- DownlinkQoSID (ID 8, integer8)
[code]....
I was able to configure the first 6 attributes, how can I add the Sub - TLV's ClassifiedID, Priority, VLAN-ID and Classifier Direction which come under Classifier. Don't see any option for that in ACS 5.x
Cisco ACS 5.x appliance?How to back up Config?What is best way, via TFTP? COPY Startup-config tftp:?COPY Running-config tftp:?I currently use Solarwinds CatTolls to back my Cisco Switches, can I use this for Cisco ACS also?
View 3 Replies View RelatedI am trying to do a query, according to chapter 4 in the ACS 5.3 Secure Access Control System 5.3
doing a PUT request have a header of Content-Type: application/xml and my payload is: [code] All I want to do is get a list of users who belong to that group?
I want send ACS logs to a syslog server .I have configured syslog under System Administration --> Configuration -->Remote Log Targets .
Name : Syslog Server
IP : x.x.x.x
Port : 514
Facility Code:Local 6
Maximum length :1024
I have open the respective ports also in firewall .But Syslog server is not getting any logs from ACS .I have another log target ,which is ACS secondary server to collect the log from primary and secondary with below config.whch is working fine
Name :Logcollector
IP : x.x.x.x
Port : 20514
Facility Code:Local 6
Maximum length :1024
I'm having trouble getting Tacacs+ to work correctly with ACS5.1 and a simple catalyst 3750 switch.I can authenticate with AAA, however i cannot get a single command to work once i'm in; "Command authorization failed" even on "enable".
Any useful resource that will walk me through the process?
configure AAA (Radius server, access list) There are two devices An access point and cisco 881w. It is necessary to set up authentication through a radius server. You can configure detailed how to do this?
View 3 Replies View RelatedACS 5.2 , and I can't find document about how to configure remote access vpn authentication in ACS 5.2.
View 6 Replies View RelatedI am writting in response to MAB issue which I noticed a few days ago and I am still not able to undestand what exactly happend. First of all I would like to say that I configured MAB authentication and according to the MAC the ISE configure a VLAN. All worked well: the test computer can change VLAN based on its MAC. The problem appear when I cut the connection to ISE server. Accourding to configuration the switch authorize the new device to VLAN 11 (critical VLAN) That is fine ! When the ISE server is up again I had a configuration which should reauthorize all ports assign in critical VLAN. But why that is not happend ??? It looks as the switch didn't notice that the RADIUS (ISE) was up and working again. [code]
View 1 Replies View RelatedI encountered some strange issues with one of our appliances in the field. Reinstalled and encountered the strange issues. No errors.. did some memory test and the seagate harddisk test and encountered SMART errors. The device didn't log those errors anywhere.. First reason to check the second harddisk. The appliance is shipped with two so the first thing I was thinking of was RAID. I saw that raid wasn't configured. Try to boot the second harddisk and saw that nothing was on that disk.. so what is the mean reason you got two of those? Got the new machine and try some options to configure RAID.You got two options.. didn't see this before, most of the time you got only one option. Raid driver on or no RAID configuration at all. First tried the intel storage matrix, configured both of the disks for mirror and install the ACS 5.2. The machine boots after installs and rejects the DVD. Result: The installation doesn't boot! Checked the partition with gparted but the partition is active (or flagged as boot) Second option was LSI, got the raid configured for mirror and the installation was also completed. Result: working installation. Tried to test if the installation is still working after removing one of the disks. Appliance is complaining the the RAID is missing one disk (so this works). After that the machine tries to boot, result: no working ACS.
View 1 Replies View RelatedACS and i would like to know how to enable the "Configuration Audit" for someone login to my network devices using their ACS login and i can monitor what they did on it.
ACS Version : 5.2.0.26
I would like to configure limited internet access to olnly a select group of Windows AD users.
I beleive cut-through proxy will allow me to do this, just not sure how to configure it on a Cisco ASA-5510
Are there any recommendations for configuring the VM for the ACS 5.x? What are the required minimum CPU-Cycles to dedicate and also the minimum RAM to dedicate?
View 1 Replies View RelatedWe are a Small company with 400-Users and currently we are using ACS 4.2 at our company.we want to upgrade and use Cisco ISE Appliance instead.
I want to know is there any major changes in configuration between ACS 4.2 and the ISE Latest Verizon.?
Is there any Hardware (Switch or Cisco AP ) compatibility issues with using Cisco ISE. (we are currently using Cisco Cat 3550 and Cisco Aironet 2600 APs with the existing ACS4.2) What ISE Series & what Soft version are the latest so i can order ?
We have a configuration that work fine but one of the combinations it don´t work. When we connect a guest laptop, the first time work fine. The configuration is when the laptop don´t authenticates with radius, the dhcp server assigned vlan guest and ip guest. The first time was ok. After, We connect a laptop with users authenticates work ok, the radius asigned vlan of users and dhcp server assigned ip users. The problem was when we connect for two time a guest laptop, radius didn´t validate and laptop didn´t negociate ip with dhcp server. In this time, the administrator of dhcp server, tell us that they didn´t see nothing traffic of my mac. and anymore run fine. If Whe change the port of switch , the laptup start working again.
Radius=NPS
Server dhcp: is typical.
Our scenario is with a ip cisco phone. the ip phone don´t have the authentication. The administrator of radius tell us that the configuratation is fine and the configuration of dhcp is fine. When we connect only laptop, everything run ok.
Configuration Port.
interface GigabitEthernet1/0/3
switchport access vlan 202
switchport mode access
[Code]...
I am having the Cisco NAC enviroment (Software Version is 4.9.1) and OOB VG.
We are getting the below and attached Error while deploying on some machines.
"Invalid switch configuration-OOB Error:OOB client "mac/ip" not found."
Some users on same switches are working fine but some are not....
What would be the possibilities and any work around? other than keeping the port shudown for long time means that atleast 10 - 20 secs or more or a PC restart. Customer is not feeling comfortable with the current situation.
i have installed system (Windows Server 2003) and i have configure Active directory for testing and configure one user under it ( TEST01)now on the same machine i have installed Cisco ACS 4.2.i'm trying to Authenticate (TEST01) using ACS but it's not working, i can't even see the logs under EVENTVIWER. simple and easy to configure since both AD and ACS is on the same machine.
View 4 Replies View Related