Cisco :: Adding Device In CS But It Is Pending In RME With LMS 3.2
Nov 16, 2011
I have fresh installed the LMS 3.2.1 without any errors. Then I am adding device in CS, give it correct credentials. Its appears in RME automatically, but it always remain in Pending devices in RME.
I have run a job in RME to check the devices credentials and it's appearing that credentials for snmp are wrong but ssh/ telnet appears as "did not try". Although I have added the correct credentials in CS for device, but it appearing as wrong in RME.
Also when I add device in CS, it's not automatically picking it's device type, until in CS I define its device type manually.
View 2 Replies
ADVERTISEMENT
Oct 18, 2011
I have a machine which is connected to a PC using an ethernet cable to communicate information between the machne and computer.I am told that the machine uses the MAC address to communicate and the computer just needs an ip address in the same range as the machine and software aware of the machine's MAC address. Why I can't connect it though the network, I tried the manufacturer who couldn't explain
View 4 Replies
View Related
Jun 16, 2012
I am having some issues adding updated definitions for Cisco C3750X-48PS switches.
We have ciscoworks LMS 3.2 and I need to update the definition/device support for these switches. We are conducting a network refresh and are having some issues with ciscoworks polling these devices correctly.
I have looked through the various user guides and searched on google with not much luck as to how to actually do this, the links I have found breifly go into it, but not indepth, and the cisco links I have found, of course have redirects to new pages which bear to resemblance to what is in the original document. Is there a clear guide out there on how to update the switch definiton in ciscoworks? So I can i can try and do this correctly?
View 3 Replies
View Related
Oct 20, 2011
I'm trying to connect a latop (Packard Bell - Easy Note) onto a Netgear N300 wireless router (WNR2000v3).I have already connected a separate laptop which is working fine but the Packard Bell (about 6 years old) wont connect, it will detect my wireless network but then asks for a "Network Key".I'm assuming this the same password that I set up when I configured the router but when I enter it I get the following message:The network password needs to be 40bits or 104bits depending on your network configeration. This can be entered as 5 or 13ascii characters or 10 or 16 hexadecimal characters".
View 3 Replies
View Related
Oct 2, 2011
I had a problem with my laptop ICS.
1 Acer laptop with windows 7 home premium
1 MSI laptop with windows 7 ultimate
1 Hp Netbook with windows 7 starter
1 USB Broadband
First i had connect the USB Broadband using by acer laptop to make as wifi router/wifi host via ad hoc.MSI laptop and Hp Netbook was successfully connected and able to connected to the internet which share from Acer laptop.Second, after that i am trying to use MSI laptop to create as wifi router/wifi host just like the same way what i done with Acer laptop.My both Acer laptop and Hp Netbook successfully connect to MSI laptop but only the Acer laptop was unable to connect to internet and it was showing "No Internet access". and the "homegroup something it showing "Unidentified network" on the MSI laptop.I had tried to restart all the laptop and netbook to resetting it, unlucky it still unable to connecting to internet.Also i had set all to "Obtain an IP address automatically".And i found out that my laptop ICS on service didnt starting and on Firewall didnt have ICS on the list.When i try to click the start buttom it popping out this:"The Internet Connection Sharing (ICS) service on Local Computer started and then stopped. Some services stop automatically if they are not in use by other services or programs"
View 4 Replies
View Related
Jan 12, 2011
Running 5 PC's and a laptop on a wired/wireless network at home. One PC running Win XP Pro started dropping the network connection (so it appeared) during browsing. Have found the following:
1. MSN messenger runs fine, and doesn't drop out
2. AVG antivirus updates with no issues
3. Web Pages in Chrome and IE will load fine one minute, then cannot load or pause for 1-2 minutes while loading
4. Can ping web addresses/IP addresses from command prompt with no issue.
5. Have changed the network connection from Ethernet to Wireless, which makes no difference to the issue.
6. If I "repair" the connection, and the network refreshes the IP address, I can browse successfully, for about a minute, before the issue occurs again. "Repair connection" again and can browse again for a minute.
7. Checking connected devices to the Netgear router, shows the PC name sometimes, against the IP address, other times it shows the PC as "unknown" against the PC address (when this occurs, web browsing is lost)
8. All other PC's on the network are fine.
View 6 Replies
View Related
Jan 2, 2011
I'm trying to get my wife's new 'All Fine 7" netbook Windows' connected via wireless connection. I had a muted attempt at it but so did my daughter and her boyfriend. I've got as far as it saying 'connected' but as soon as it does I get a message; Error from RasDial. I think I have created some conflicts perhaps! In the control panel I have done the following:'Internet options' under 'Connection' I've highlighted 'USB 'Network & Dial-up connections I have a choice of 'My connection' 'Main Computer' 'RT28701' & 'ENC28J601' The connection I have so far seems to be using the RT28701.My other option to 'USB is to select 'Desktop @ 19200' but that didn't seem to work either.
View 9 Replies
View Related
Mar 19, 2013
Cisco ISE 1.1.3 is running in standalone mode, when I made any configuration it show me the notification that "Configuration changes has been recorded but remain pending" .
View 1 Replies
View Related
Oct 6, 2010
ACS 5.2 , in my Primary ACS under System Administration > Operations > Distributed System Management I see my Secondary but it shows "PENDING" under Replication Status.
View 3 Replies
View Related
Feb 15, 2011
im intending to setup a small office network through a sever at my work and would like to know if it is possible to have the network running with each pc having its own internet connection.in theory this should work by having the internet connected via usb which will leave my ethernet ports free for the network..i would just like to know if this route will work just like that or will i need to have a rethink.
View 13 Replies
View Related
Mar 19, 2011
Brand new MSI system using windows 7. we're using a wirless network in the house, and up until today it's been fine. Randomly, Windows is no longer detecting any networks.
I've confirmed there is no prob with the router or signal as I can detect the network in my room and connect to the internet (using a homeplug hardline). I've tried enabling and disabling both the router and wireless card, a system restore (windows made no changes), and when I came to use the windows 7 troubleshooter - it says the device is not enabled?
View 4 Replies
View Related
May 11, 2011
Okay, so our old computer took a dump & our friend rebuilt us a new one and he threw in a new router to go with it. Its a D-Link router, which is directly connected to our desktop. However, upon completion of a new desk installment, we put the router into the cabinet and my gateway laptop immediately stopped being able to connect to the internet or the router at all.
1) The router is connected to the internet and broadcasting.
2) I've reset and refreshed the router and my window of available networks on my laptop, which did not work.
3) I've pulled it out of the cabinet, which also had no affect.
4) I did a manual search for the router, and it says the network already exists and asks if i would like to connect and upon agreeing to this, it returns me to the page of available networks, which does not include my router.
View 11 Replies
View Related
May 16, 2011
i have recently added to a domain. The initial setup is a server running windows 2003 and several xp machines which logon to the domain using mandatory profiles. However, after adding windows 7 machines and logging them on to the system it doesnt load the profiles. (which is fine as I understand you cannot use the same profiles with windows 7+xp)The problem is it automatically creates a roaming profile when logging off and saves it back to the same path as the other profiles under user.V2 which is growing considerably and causing huge logoff and logon times.How can I get the windows 7 machines to not attempt roaming profiles back to the server and instead to just save the profiles locally when logging off.
View 14 Replies
View Related
Jan 3, 2013
We are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies
View Related
Nov 30, 2011
My BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies
View Related
Feb 11, 2013
The problem: I need to track a bus from city to city in real time.I'm thinking of a gps device without screen or apps, it only sends the current location to a server. Is this possible? What device can be useful?
View 1 Replies
View Related
Jan 24, 2013
I have an 1801w connected to ATT/Bellsouth FastAccess via its DSL port. The LAN connection is through FastEthernet1 trunked to an Extreme Networks Summit 450e. My 1801w configuration is attached and everything is working great.
My problem: DSL bandwidth is unfortunately limited to 3mbps/384kpbs in my area, so I'm considering adding a second DSL line and aggregating bandwidth (load balancing) between two.
1) Can this be acheived using the 1801w, perhaps by adding an external modem for the second DSL connection feeding the 1801's FastEthernet0 port?
2) If yes, then might anyone have a specific modem recommendation? If no, then what other equipment would I need?
3) Most importantly, what 1801 configurations changes required? (I expect my goal would be to equally share the WAN links between all connected VLANs/networks, but if necessary I suppose a workable alternative might be to dedicate a new VLAN/network (e.g., "office") to the new WAN link.
View 7 Replies
View Related
Sep 4, 2011
I've download free trial from cisco site Cisco LMS. I've installed and now I have a question. how to add a device ?
View 10 Replies
View Related
May 14, 2012
I've added a number of switches to NCS and some of the switches had the wrong snmp communities, etc so weren't added as switches but instead were put under unknown devices.
I've corrected the information for each unknown device and am now seeing the following inventory status:1951799867 (IP: 10.243.26.22) will not have its features collected due to , device SPT_ONLY
They're still unknown devices and there seems to be no way to get them to show up as switches.I've tried to remove these devices but without success (despite a message appearing below the devices I tried to remove saying "Selected device(s) removed successfully.")
View 1 Replies
View Related
Dec 21, 2012
I have E1 interface that supports 2Mbps and i need to connect Point to Point , my question is can i add 2 more E1 interface on my cisco router and configure it using channels on that link so i can increase my bandwidth up to 6Mbps.
View 5 Replies
View Related
Nov 1, 2012
I recently upgraded from WCS 7 to Cisco Prime Infrastructure 1.3 (1.3.0.20). I've successfully added my 5508 WLC, 7204 router, 4506 Switch and several other devices. The one problem I have not figured out is how to add my 50 + AIR-LAP1142N-A-K9 to Prime. I can see under Home > General > Overview that I have AP availability of: 53 but when I go to Device Group > ... > Unified AP > Cisco 1140 Series Unified Access Points there are no devices listed. I've tried to manually add them but they fail.
View 6 Replies
View Related
Mar 21, 2011
Seems that all solutions are null and void for us because we are not using SNMP v3 or H.
We are using SNMP v2, We have upgraded our WCS to latest version as well as the controllers. I have 6 controllers currently added although they are on WiSM blades.
We are unable to add the 5508 Controllers, we keep recieving this error -
No response from device, check SNMP communities, version or network for issues.
I have confirmed all connectivity is working, even with a debug on the controller you can see it sending SNMP packets to the WCS, although still same error.
View 8 Replies
View Related
Aug 15, 2012
We have a Cisco 1941 Router with two single HWIC cards supporting two T1 lines 3Mbps total bandwidth. We have a distance learning lab that takes atleast 2mb connection when in use so it realy kills our bandwidth. I was looking to possible add a thrid T1.
My question: Can I just buy a double wide HWIC card and replace the single port one. Would this require re-configuration or it's simply plug n play?
What other options can I try for more bandwidth instead of adding thrid T1.
View 4 Replies
View Related
Sep 13, 2012
How could I add an AP 1522 ag without DHCP. How do I setup the IP address configuration? For some electrical problem I lost 4 1522 APs. I have two controllers and a windows server running WCS. Now I have just one AP up and running. After booting a new AP I could not get in "config mode" via console so I tryied to setup the IP config as follows (pressing ESC key during the boot):
set IP_ADDR 10.1.1.100
set NETMASK 255.255.255.0
set DEFAULT_ROUTER 10.1.1.1.1
then: "boot"
*** I have authorized the new AP in "MAC address filtering" via WCS.
*WCS version 7.0.164.0
I think that is no request reaching the controllers.
View 5 Replies
View Related
Jul 11, 2011
I have a SG-300-52 port switch configured Layer 3 with mutiple VLANs. I have run out of ports. What is the best way (or easiest) to bring up a second SG-300-52 port switch with the same VLAN configuration?
View 1 Replies
View Related
Apr 15, 2013
I recently upgraded from WCS 7 to Cisco Prime Infrastructure 1.3 (1.3.0.20). I've successfully added my 5508 WLC, 7204 router, 4506 Switch and several other devices. The one problem I have not figured out is how to add my 50 + AIR-LAP1142N-A-K9 to Prime. I can see under Home > General > Overview that I have AP availability of: 53 but when I go to Device Group > ... > Unified AP > Cisco 1140 Series Unified Access Points there are no devices listed. I've tried to manually add them but they fail.
Not a lot of clear documentation about this and I'm not sure what to try next.
View 14 Replies
View Related
Sep 28, 2012
I'm a newb at this stuff and hope someone will take pity on me and point me in the right direction?In a nutshell, we run a SBS2008 server at work with 20 users. Our company has a domain name which, via DNS hosting is pointed to our static IP. Email address's are handled via the server using Exchange 2007. Documents and files are stored on a data drive on the server (lets call it Server 1). We have now setup a second business with a different domain. I now have 10 users who will need access to the files on Server 1, but will run under a different domain (and need different email addresses) and need to have access to files stored on Server 1 and the new Server 2. The current setup is simple. ADSL comes into the server room and goes to a modem/wireless. From there it goes to the server which handles the DHCP. The server is in turn connected to a 24 port switch which then feeds the workstationsI have access to purchase another server and whatever hardware is required. No amount of Googling matches my scenario hence my question. What I'm really after is a mudmap showing setup or the right way to set this up
View 8 Replies
View Related
Dec 22, 2012
If I did use the hub would I get full speed on the PC or PS3 as long as one or the other was switched off or would I always get half speed regardless?
View 5 Replies
View Related
Dec 22, 2012
I have recently purchased a PS3 and would like to add it to my network. I currently have router in an upstairs room and it is linked to my PC in the basement using an ethernet cable.My new PS3 will also go in the basement. Question: as there is only the single cable going to the basement could I link the PS3 using a hub? I have a small Netgear hub left over from years ago would this work? If I did use the hub would I get full speed on the PC or PS3 as long as one or the other was switched off or would I always get half speed regardless?
View 2 Replies
View Related
Jul 28, 2012
Im wanting to add an additional module in to my Cisco 4500. Is as simple as plug and play or is there some commands that I need to add or anything I should be aware of.
View 2 Replies
View Related
Mar 16, 2011
We have an ASA 5505 and I need to set up port forwarding for an unusual port number which will be used for FTP on an IIS server.It's a bit complex as there are 3 VLANs: these are called ISP, Server and LAN-side VPN. We need to add a TCP port 8521 forward from the server's IP in Server WAN to ISP WAN VLAN with public IP address.
View 1 Replies
View Related
Jan 17, 2013
I need to unlock IPSec to my 1941 router but I'm not sure which license(s) to purchase.
View 1 Replies
View Related
Aug 2, 2012
I currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies
View Related
