Cisco Application :: Monitor TPS Value For ACE-SSL-05K-K9 Module
Sep 1, 2011
I recently installed the license ACE-SSL-05K-K9 on ACE10 with multicontext solution.The license provides 5000 Maximum number of SSL transactions per second (TPS).The customer would like to track this to find out the correct size and in the case of services https upgrade licenses.Can I do it so through particular output or it's necessary monitoring with snmp service? In the second case, can you tell me the oid string to use?
In case the module should receive a higher number of connections to that provided by the license, what's the issue for new https connections?
We are using a Ace module running version 3.0?We do have a service which can now be reached by a url like https://www.xxx.com/yyy/ < notice the last /This is running via the Ace which terminates SSL and so on..
So now our client wants an url like https://www.yyy.com . The backend realservers and place of virtual dirs on IIS stays the same.
So now /yyy/ needs to be added to the backend realserver request, so the correct virtual dir is used. Therfore I need to add this Uri towards the realserver.
I Just deployed some of these new modules and running A4.x code. How to configure an ACE with the maximum context?
We run in tranparrent mode with 110 Contexts, we found that with a base config for each context(80 lines of code) this would only leave us with 7% of available RAM. The Device begins to shut down services @ 5%. like SSH and others.
So, Is this even possible to configure 250 contexts and still manage the device.
I am currently stuck to setup an automated configuration backup for ACE Blades. I found a script to backup the ACE from the Cisco ANM box but unfortunately I am not very familiar with Linux. (script) in place, to "pull" the ACE config from a Microsoft system ?
Whatever a NAT is supported for ACE-20 module? I do need to convert working CSM(SLB) config to ACE configuration and I am not quite sure if the configuration below is correct. ACE module should be configured in bridge mode with two vlans - vlan 36 (client) and vlan 436 (server) - bridged with interface bvi 36. NAT on ACE configurad as "nat dynamic 1025 vlan 436" into corresponding "policy-map type loadbalance". Check two parts of configs and if the ACE config is properly converted from CSM and will be working in the same way (especialy for NAT). [code]
I have an ACE20-MOD-K9 with version A2_3_6a, and i am having problems in cookie persistency. the setup contains 4 servers using round-robin algorithm and cookie persistency and that receive http traffic on port 9090. I have been receiving complains that the users are getting disconnected randomly while accessing the web application through ACE. Below is part of the config, when setting the timeout of the cookie to default or something equal to hours, the disconnection/complains gets worse.
I wanted to find out how many times can I apply a healthcheck in a single context. I have 50 farms that are using the same port and instead of creating 50 different healthchecks, I want to just create 1 healthcheck for the 50 farms and apply it to each farm. I also need to know if the same limitations (whatever they may be) is the same for the 4710, ACE20 and ACE30.
We have a 6509 with an ACE module. For reasons I don't fully understand the ACE is running using a BVI in bridge mode. It has loads of secondary interfaces.
I can ping all of the IPs on the BVI, but only servers in Subnet 10.7.42/42 can ping out of the the layer 3 on the 6509. I have all the routes configured properly on the 6509 pointing to the ACE for these subnets. The question is though the config has been excepted, is there a limit to the number of secondary on a BVI.
we use ACE30 module, ver. A4(1.0) for access to intranet application. The https connection from client is terminated on ACE module, LB algorithm is used and new SSL connection is initiated to the server. Standard operation works without problems.
But when user generates a .xls od .pdf report in the application, it should open in a new popup window. Problem is, that it does not (but on the server, the report is generated and stored). The PC and browser are configured fine, when accessing the application from the same PC directly (bypassing the ACE module), the popup window appears.
i have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?
I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
Does ACE service module support SHA2(256) certificates? I see that private key generation defaults to SHA1 and does not provide any option, also the cipher suites in SSL parameters map do not show SHA2 options. Can it handle SHA2 in any software release? I am currently running A2(2.3) build 3.00
I am desiging a topology with two Cat 6509 and Two ACE Module, one ACE per Catalyst. I am thinking to use bridge mode for the customer contexts, I would like to know if the Bridged mode is an Assymetric topology.
The server gateway is the ip address of the ACE or the Router?
I have a ACE module A2(3.5) installed, I am having a connectivity problem between two servers in my network. I have captured some traffic on different points in my network and from capture it seems like the problem is with this ACE module or somehow it is closing the connection.
I am in the process of configuring load balancing on ACE module but struggling to configure virtual IP address for ACE module. I'm working on ACE30 module and using software version A5 (1.2). ACE module is in slot of Catalyst 6504 switch.
I trying configure ASN traffic load balance, but doesn't works.I have one Cisco Catalyst 6509 and onde Cisco Ace10 module, in my context "PanWEB" i have the interfaces above: [code] If i try to establish a telnet session(telnet 10.96.202.10 80) i see the SYN packet passing through the ACE and going to the real server, but, the server do not response the SYN packet. I done a capture in the server using wireshark and could see that the IP address of the destination is the VIP and not the rserver ip address , this is a problem? Why can not I have the SYN + ACK from the server?
We are facing a strange issue, our ACE 20 got failed due to power issue , after RMA once we are installing ACE 20 to 6509 , the status LED is showing ORANGE . The sh module shows it as " Others " ... The IOS is same as it was previously in 6509 .
I am trying to get documentation on how to integrate an ACE30 module in a service chassis design integrated with the Nexus 7000 in routed mode. Only documentation I could find shows this design with the ACE30 module in a one arm mode. Any documentation that shows this implementation of this design?
What are the maximum number of real servers, server farms and virtual servers i can configure on ACE30 module,Is there any documentation available on cisco site where i can check this? Does it depend on the hardware or does it depend on the software version?