monitoring oracle database performance by JDBC connection from CSS11506?
if it is not possible to do so, if there is otherway the system do eitehr application server or DB server is performance is too low?
my SAM card always reach cpu 40%, few times reach more high, even to 100%.
my show chassis gives:
1 CSS5-SCM-2GE primary
2 CSS5-SAM primany
3 CSS5-SSL-K9 primany
can I limited the VIP? I really do not think the system is heavily used. could any configuration wrong cause problem could be possible the module has problem? if so, how can I confirm? could I add another SAM module?
I have installed anm 4.3 and is trying to setup monitoring my css11506. I have added the device and on the monitoring-setting-polling status, said the polling configuration is enabled, but the polling status time out.
The css11506 snmp configure as:
snmp trap-type enterprise
snmp cmmunity xxxxx read-only
snmp name "anm v4.3"
[code]...
How to correct it?
Currently using a CSS1506 for our reverse proxy SSL.I have a couple of questions
1 - Does the 11506 use an internal disk as well as the one in slot 0 ?
2 - I have a spare mem card in slot1, how can I copy all of the required boot files etc to slot 1 in case of a card failure in slot 0?
I am planning to perform a failover drill between active and standy CSS loadbalancers which are configured in a cluster pair. I am looking for help to know what show commands I can run to validate that the failover occurred successfully from primary to secondary load balancer and that the VIP's have failed over successfuly as well.
View 1 Replies View RelatedI recently installed the license ACE-SSL-05K-K9 on ACE10 with multicontext solution.The license provides 5000 Maximum number of SSL transactions per second (TPS).The customer would like to track this to find out the correct size and in the case of services https upgrade licenses.Can I do it so through particular output or it's necessary monitoring with snmp service? In the second case, can you tell me the oid string to use?
In case the module should receive a higher number of connections to that provided by the license, what's the issue for new https connections?
what is the OID for See the hit status of the spefic VIP and RIP coming under the VIP .apeart from this CSS box having any module to moniter the hit status or VIP's and RIP's
View 2 Replies View RelatedBelkin Setup / Router monitor application has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available.
View 1 Replies View RelatedI want to use MRTG to monitor my DSL connection bandwidth useage.
Should I monitor:
ATM 0/3/0 or
Dialer 1 or
Virtual-Access 2
ps. is the 'BW' aspect of show interfaces important? I have 56Kbit/sec on Dialer 1, 100,000 Kbit/sec on Dialer 1 and 1024Kbit/sec on ATM.
Any app i can install which will monitor my lan connection for dropouts? i have searched but can't find any that work. I just want a simple app that will note down each time the lan loses connection and keeps a log so i can be sure if its the computer or the network at fault.
View 1 Replies View RelatedI need an tool to monitor the internet connection and bandwidth at my windows xp desktop.
View 4 Replies View RelatedI have a dual wan router with a main cable modem for high speed and a backup adsl modem hooked just in case. The problem is that quite often it seems that my ISP loose his connection to the internet but communication is not lost between my ISP and my modem and router. Because of this, my router doesn´t do the automatic changeover from my WAN 1 to my WAN 2 hooked slower ADSL modem. My router has the ping to keep alive option checked on the WAN 1 setings using my Cable ISP provided IP address.How can I force my router to notice that my cable ISP lost his connection to the internet and do right away the changeover from his WAN 1 to his WAN 2 input?
View 1 Replies View RelatedAll my previous routers have allowed me to monitor my connection speeds however I can't find this in this router. I found the client table under "status" but I have not been able to find the connection speeds anywhere. I like to make sure that my devices are running at close to 300Mbps and not 54Mbps in case I have a connection setup wrong. I have searched in the forums without much luck.
View 9 Replies View RelatedI have been using a Linksys E3000 router for a few months now. Love it. But this last week, when ever I wake my monitor up after it's power saving mode kicks in, I lose my internet connection for about 15 seconds. If you look at the router before the monitor is on, I am connected. The light is on for port 1. But as soon as my monitor gets turned back on, it light just turns off and will reconnect after about 15 seconds. I've looked it up online and can only find things about when the entire system wakes up, and usually those people have to reboot their entire system to get a connection again, or turn the router off then back on. Using Windows 7?
View 4 Replies View RelatedWhy do my connection not clear when my service goes to a down state. The only way I can get the connections to clear is by bouncing my content rule. CSS11503 version 08.20.4.05s - SSL all the way to the server --- I also have flow permanent port3 443 configured, but I don't understand why the other two servers go to zero while server01 never goes to zero. If I remove the flow permanent port3 all the counters go to zero, but I would think if the servers goes down then the connections should go to zero regardless of the flow permanent port configuration. [code]
View 3 Replies View RelatedWe have a rather strange issue, and I'm not sure it's really a problem with the ACE or not. We created an HTTP parameter map called "TCPreuse" and applied it to a virtual server. A show conn detail displays "[ conn in reuse pool : FALSE]" for all connections pertaining to this virtual server. The rserver in question is Linux(Ubuntu) + Apache.Next we applied the HTTP parameter map to another virtual server - this time IIS7 + Windows Server 2008. There are plenty of entries "[ conn in reuse pool : TRUE ]" when I do a "show conn detail".What could the web servers be doing differently that would cause the connection reuse to work on one virtual server and not the other?
View 1 Replies View RelatedWhat exactly happens when the SSL connection rate is exceeded. Is the connection dropped, queued or what ?
Defined as the SSL TPS. In our case 1000 but upgradeable to 5000
In my lab I have only one ESX server. On this server I am running VSM and vCenter (appliance).I am trying to get 1000v working however everytime I try to migrate my ports I get the following error:Network configuration change disconnected the host '192.168.0.10' from vCenter server and has been rolled back.fault.NetworkDisruptedAndConfigRolledBack.summaryIt seems that it doesn't like the fact that vCenter lives on the same ESX host as I'm trying to migrate. How I could get this to work?
View 1 Replies View RelatedI have CSS CSS11501 which is working fine in single arm deployment. Now I want to have redudency so that in case the switch 1 where CSS is currenlty connected is down.I can reach the CSS through the second switch 2.Both the switch are trunk with each other and CSS has one port connected with Switch 2.
View 2 Replies View RelatedI require to connect a "css11501" two core switches to provide redundancy to the load balancing service and would like to verify this possible (Does the spanning-tree protocol officer for load balancing?)
View 2 Replies View RelatedI'm expecting some problems with ACE. I've configured it to loadbalance between 4 nodes with SSL termination at ACE.
Everything was working fine up to the identification of a problem using firefox browser. With Chrome and IE works fine.
The user is trying to upload a file to one of the 4 nodes. When the costumer click at the send button, the Firefox shows the following message: Connection Reset.
This problem just happens when the user try to upload the file. Whe he's just surfing through the system, works fine.
------ Configuration ------
ACE-01-SJPR/eproc4# sh run
Generating configuration....
logging enable
[Code].....
How do I apply the connection parameter map in a configuration like this to the service policy int827? Do I need to define the traffic? Can I specify only one source destination flow to apply the set tcp half-closed TCP normalization against?
policy-map type loadbalance first-match wss-1100-l7slb
class class-default
sticky-serverfarm sticky-srcip-1100
policy-map type loadbalance first-match wss-1101-l7slb
class class-default
sticky-serverfarm sticky-srcip-1101
[code].....
I'm running v4.3.5 in our WAAS environment. At the CLI of one of our 7341 WAEs, there are several connections that show up [code] However, in the Central Manager nothing shows up - not even empty graphs - when I click on a device and go to monitor/connections statistics. After a few minutes, I do get an error message that states "Error retrieving connection stats. Please ensure that the device is online and then refresh." By the way, I get all other statics in the GUI such as Optimization Details Report, Traffic Summary Report, etc. Another thing, these WAEs are behind a router and supposedly the ports to allow access to/from the WAEs and other data is allowed through the firewall.
Is there some special port that needs to be opened on the firewall to allow for 'connection statistics' information displayed, that doesn't need to be opened for the other statistics to display? Or could this be a bug in the software?
I have a ACE4710 setup to load balance a couple of web servers. The real servers all show as inservice as do the propbes and serverfarms/virtual servers. If I ping the Virtuual server ip address I get a reply but it I try to access VIP via telnet or web browser. I get a connection could not be open error on the client.The question is how do i determine where the error is comming from so far I can not tell if the client is getting through the acl or not.I have used the trouble shooting guide and nothing has worked to determine the cause so far. show service-policy int479 detail does not show an increase in the hit count when I try to connect.show stats conn does not show an increase in failed or timed out connections when i try to connect. [code]
View 3 Replies View Relateddefault inactivity connection time out for A3(1.0) So by defult any tcp connection(http or https) will be timed out in an hour. [code]Was this change in the A4(2.0) code or is it still the same? I heard a TAC engg say that default inactivity timeout for http and https are now 5 mins that is 300 seconds.
View 3 Replies View RelatedI have a ACE module A2(3.5) installed, I am having a connectivity problem between two servers in my network. I have captured some traffic on different points in my network and from capture it seems like the problem is with this ACE module or somehow it is closing the connection.
View 6 Replies View RelatedI've configure two ACE 4700 in a SLB modus http to a web server.To understand how the ACE works and to see if all are ok, I want to test it? but how?
How do I do to initiate a http connection between my test pc to the webserver through the ACE?
I Updated the 5508 from 7.0.230 to 7.4.100 and made it a cluster.Sinse the Update the handscanners loose the connection to the AS400 Application.Where to start troubleshooting?I did a debug client, I see the client is roaming but I can not say if there is a relation between roaming and loosing connection to the application.
View 19 Replies View RelatedCan i send "show conn" to syslog server? for example:
[code]...
ESTAB5082
can we make a bridge connection between cisco aironet 1400 series and cisco R5005?
In Root and Non Root Manner.
Everytime I make a config change to one of the contexts on our ACE20, I get this message: Config Application in Progress. This command is queued to the system
If I run show download info, I get:
context : context1
Interface Download-status
--------------------------------------------------------------
187 In Progress
199 Pending
Regex download optimization status : Couldn't get status[TNRPC Timed out]
It eventually seems to complete, but it takes a very, very long time. We are running Version A2(3.5) [build 3.0(0)A2(3.5)].
Report run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.
View 6 Replies View RelatedI am taking an introduction class to CCNA and we are focusing on the Application Layer,and I'm having some difficulty in understanding what is an Application Layer Service. Is the Application Layer Service the same as Application Layer Software?
View 3 Replies View Related