Cisco :: Cannot Access One WLC 5508 Via Wired Interface

Feb 8, 2013

I have 2 WLCs (Cisco 5508) in my network. The primary has 16 Aironet 1261 APs connected. Secondary WLC is just staying there and no APs are associated with it. Everything works fine. I was accessing the controller via a wireless client all this time through the management interface 10.74.15.2 using https. It was working fine.But when I tried to access the primary using the wireled network, I can access the seconday but cannot access the primary. They are in the same subnet and I can ping both of them.

View 2 Replies


ADVERTISEMENT

Cisco Wireless :: WLC 5508 7.3 Management Interface Access To GUI?

Jan 16, 2013

After I've upgraded software to the v7.3 and applied AP-SSO it made imposible to access the controller's gui via Service-port. So we tried to access it by management-port, but there is some problem too. It is not working from another subnets. But default gateway on management vlan is set correctly and I even tried to turn of all acl's on switch. WLC is only accessible from the same network. But at the same time wlc is replying on ping fine.All other protocols cannot connect to the controller.

View 3 Replies View Related

Cisco :: 5508 - Unable To Access Controller Using Management Interface

Apr 3, 2013

I configure IP address on the management interface port 1 of 5508 controller when i connect it direct to my laptop i can't ping or access controller from my laptop even i connect through layer 2 switch still i can't not.
 
IP Address of management interface : 10.21.0.50
Laptop IP Address : 10.21.0,51

View 13 Replies View Related

Cisco Wireless :: 5508 Internet Both Wired And Wireless / Access To Server Everything Dead

Oct 24, 2011

have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network.  All internet both wired and wireless, access to server everything dead.  I then have to directly connect to the service port and disable the global multicast mode.  Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled.  I have it enabled on our wired network and it works OK there.  ted.

View 10 Replies View Related

Cisco Wireless :: Windows Sharing From WLC 5508 To Wired LAN

Mar 4, 2012

I'm having problem with windows sharing (file/printer sharing) from Wireless lan client which is connected to AP3500 and WLC 5508 then to Nexus 7010. It's already using ip command, for example \192.168.84.65 WLC os version 7.0.116.0 (using AP groups) Nexus os version 4.2(6) The weird thing is i can connect using windows sharing from wired LAN to wireless user however not vice versa. f

-Wireless lan to wired LAN using windows sharing - failed

-Wired LAN to Wireless lan using windows sharing - success.
 
I've been analyzing by making sure that all the to end, there would be no firewall within source pc(s) and destination pc(s) and also the ACL inside Nexus. Been dying here to find solution for this, due to the customer is using it for file and printer sharing service.

View 2 Replies View Related

Cisco Wireless :: Wired Guest Network On WLC 5508?

Oct 3, 2012

Could I setup wired guest Internet connection without layer 3 web authentication and how?I want guest users access Internet without going through web authentication.

View 2 Replies View Related

Cisco :: 5508 - SSH And HTTPS On Controller Interface?

Jan 9, 2013

I have a wireless controller 5508 and all my interfaces can be accessed via https or ssh from a wireless client. Management access from a wireless client is disabled so I don't understand why this is happening.

View 10 Replies View Related

Cisco Wireless :: 5508 - Cannot Connect To Web Interface Of New AP

Mar 13, 2012

I am in the process of upgrading our wireless infrastructure from a series of APs centrally managing the infrastructure centrally with the WLC 5508 and new APs (1142). All seems to be going well, the APs see the controller and are downloading the latest information/changes and I can connect to a test network. The current issue I am having is that I cannot connect to the AP via the web interface.
 
The config for the management interface of the 5508 is:
interface GigabitEthernet4/0/20
description ** Connection to WLC-5508-01 **

[Code].....

View 2 Replies View Related

Cisco Wireless :: 5508 To Use Same VLAN And WLANs For Wired Guests

Jan 2, 2013

We created a VLAN interface and a WLAN on the wireless controller (5508) and using it for Guest Wireless (Web auth), can we use the same VLAN and WLAN s for Wired Guests also?

View 5 Replies View Related

Cisco Wireless :: WLC 5508 Interface Addressing - Limitations?

Aug 26, 2012

Is there any limitations of network size for an interface in a WLC 5508? Any recomendations of netmask size? Maximum /24, maximun /21?

View 5 Replies View Related

Cisco Wireless :: WLC 5508 Cannot Create AP-manager Interface

Aug 9, 2012

Yesterday I was in one of our client premises configuring a WLC 5508 with software 7.2, went through the initial configuration wizard with no problem whatsoever, my issue began when trying to configure a ap-manager interface.In many WLC configuration guides cisco states that for 5508 it is not required to configure an ap-manager interface because the management will suffice, but then they put a side note recommending it's configuration for best practices and better performance. OK so I saw that in an earlier version document and now they do not make the recommendation but the still use the word required and for me that's still is not a limitation. I can't create the ap manager interface because when I put the VLAN ID it says the it is being used by another interface.

View 5 Replies View Related

Cisco Wireless :: WLC 5508 Management Interface Connection

Aug 1, 2010

I'm setting up a new 5508.  I've used the config from a 4402, have successfully connected to the Service port to manage the device, but for some reason cannot connect to the Management interface.  In this case, port 1.
 
The service port is connected to a Catalyst switch and grabbed an ip address (10.2.x.x subnet) no problem.  I can access the 5508 via https using the SP.  However, port 1 is connected to the same Catalyst switch, but on a different vlan (subnet 10.20.x.x).  Both ends show that the interfaces are up, I can ping the interface from any other host on the network, but when I try to manage the device via https I cannot connect.  We are using WCS and I cannot add the device from the WCS.  About all I can do is ping that interface.

View 6 Replies View Related

Cisco :: WLC 5508 / Failed To Get DHCP Response On Interface

Jul 10, 2012

i have WLC 5508 showing the below Logs , which prevent the users from connecting to the SSIDs , also its disconnecting the associted users DHCP Socket Task: Jul 11 09:54:08.992: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'interface-02'. Marking interface dirty.*mmListen: Jul 11 09:54:08.638: %MM-3-INVALID_PKT_RECVD: mm_listen.c:7671 Received an invalid packet from 10.21.1.25. Source member:0.0.0.0. source member unknown.it shows 3 to 4 times durring 1 hour ,

View 2 Replies View Related

Cisco Wireless :: Additional AP-Manager Interface On WLC 5508

Aug 25, 2011

at the moment we are using as default the manager interface as ap-manager interface.
 
Now I have to change the IP. I would like to change that very smooth with all our locations. My question, is it possible to add a ap-manager interface with a new vlan and IP Range, so that I can move the AP's to the second interface as as soon as it is planed with the location. Sometimes in special cases we have hard coded the WLC IP oder we just need to change the DHCP option but this needs to be planed and I see problem to do that in a hard cut.

View 11 Replies View Related

Cisco :: 5508 Controller Setup - Management Interface

Jan 2, 2012

I'm trying to verify some behaviors I'm seeing with my 5508 controller setup, I've zero experience with this hardware and clueless on the best practices. With that said... out of the box I ran through the AutoInstall process.

I gave my service port an IP address on my subnet, 10.10.8.0/24 vlan 100 and gave the management interface the ip address 10.10.30.5/24 vlan 130
 
From my host I can ping the management interace 10.10.30.5 and the interface gateway 10.10.30.1
I cannot connect to the controller via 10.10.30.5 either through the web GUI or telnet
I can connect to the controller via 10.10.8.200 both through the web interface and telnet
while connected to the service port, I can ping the management port IP but I cannot ping the 10.10.30.1 gateway.
 
We have attached two test 3502I AP's and they found the controller and pulled correct ip addresses, clients can authenticate and access network resources as well as the Internet so for the most part, things are working but it concerns me that the management interface can't ping its own gateway.

View 8 Replies View Related

Cisco Wireless :: 5508 - Maximum Number Of Wired Guest Clients?

Jul 10, 2011

which is the maximum number of simultaneous wired guest clients on a 5508? And in a 2112 controller?
 
Wired clients count as wireless clients??
 
What about anchoring limitations, what is the effect of wired guest clients on the anchor controller?

View 2 Replies View Related

Cisco Wireless :: 5508 Static IP Address For Guest Wired Network

Dec 4, 2012

I setup a guest wired network on the WLC 5508 with 7.2.110.  A postage machine can only be setup for static IP address over guest wired network.  Is any one how to get it configure on the WLC 5508?

View 3 Replies View Related

Cisco Wireless :: AIR-LAP1242AG-E-K9 Shutting Radio Interface (WLC 5508)

May 31, 2013

I am wondering if anyone has seen this before. We have about 50 AIR-LAP1242AG-E-K9 access points connected to a WLC5508 running 7.4.100.0. These were all being used as autonomous APs previously and were converted when the controller was installed. About 12 of these have a lovely feature where their radio interface goes down at random. The radio is still in enable mode but the opertational status is DOWN. It seems to happen particularly when there has been a power outage and the AP rejoins the controller. All of the other 1242s are fine and never sees this problem. The APs are all on power injectors.
 
Once the radio is down, the only way I can get the to come back online is by doing the following:
 
1. Set the radio admin status to "disable" and apply

2. Turn off CDP

3. Reboot the AP Wait until the AP is back online and registered on the controller
 
4. Enable the radio admin status and CDP.
 
If I do not remove the CDP setting I cannot bring the radio back to "UP". I know we had previous issues with autonomous 1242 APs that did not like CDP being enabled. Have I perhaps got a bunch that are like that? Despite these having operated as autonomous APs they are AIR-LAP1242 from the factory.

View 6 Replies View Related

Cisco Wireless :: 5508 / WLC Management Interface Not Bound To Port

May 6, 2013

I have 2 x 5508 Wireless Controllers, 1 mgmt port on each as standard. I noticied something different between these controllers running the same code.I can bound a physical port to the mgmt interface on one controller but not the other (both interfaces are untagged)see below, this config appears on one controller but not the other? Is this something to do with the initial setup? How can I add Phyiscal information to the other controller mgmt interface, I cannot delete the mgmt interface. Physical InformationPort Number Backup Port Active Port Enable Dynamic AP Management?

View 2 Replies View Related

Cisco Wireless :: WLC 5508 / Cannot Create Interface As Same Vlan Id And Subnet

Aug 12, 2012

I have got a wireless project with WLC  main office and have 10 sites where ap's are there and ap's getting registerd .we need 4 ssid in all branches same .

ssid guest
ssid scanner
ssid user
vlan 600 main office for scanner 192.168.1.0
in branch
vlan 600 for scanner but ip is 172.16.1.0

and bgp is running . And customer is asking me not to edit the ip range or vlan or create new vlan . but in wlc am not able to create branch network 172.16.1.0 range interface and vlan 600 as vlan 600 i already created for scanner main office 192.168.1.0 So is there a way to do that .
 
Temprarly one site i did like created vlan 610 in branch no ip . And in main office interface vlan 610 given another ip range . and i created interface in wlc . from branch i can connect the ssid and getting ip . But they dont want to create any aditional vlan or another network . Customer dont have a smartnet contract . They recently baught 2 wlc 5508 and 40 ap 1142.

View 4 Replies View Related

Cisco Wireless :: Backup Port Of WLC 5508 MGMT Interface

Sep 8, 2012

Since WLC5508 MGMT interface is configured a AP-Mgr at the same time, can I set a Backup Port to WLC5508 MGMT interface? Refer to WLC configuration Guide:
 
In the Backup Port text box, enter the number of the backup port assigned to the management interface. If the primary port for the management interface fails, the interface automatically moves to the backup port.
 
Note Do not define a backup port for an AP-manager interface. Port redundancy is not supported for AP-manager interfaces. If the AP-manager interface fails, all of the access points connected to the controller through that interface are evenly distributed among the other configured AP-manager interfaces
 
if I need to configure the backup port for MGMT interface, i need to remove the AP-manager on MGMT interface and create a network dynamic interface for AP-Manager ?

View 2 Replies View Related

Cisco Switching/Routing :: VLAN Interface Quantity Of WLC 5508?

Apr 25, 2013

How many VLAN Interface can be create on a WLC Interface, e.g. GigabitEthernet 1?

View 2 Replies View Related

Cisco Wireless :: WLC 5508 - Ignoring Primary Discovery Request Received On Interface

Jan 13, 2013

Im receving this error on my syslog server: capwap_ac_sm.c:1443 Ignoring Primary discovery request received on non-management interface (2) from APalready checked the configuration and everything seems ok. They are registered and with clients associated.What could be the cause?

View 2 Replies View Related

Linksys Wired Router :: RV042 - Remote Management Disabled But Interface Remotely Accessible

Feb 2, 2007

We have a RV042. remote management is set to DISABLE - but even after restarting the router i can access the interface remotely over the internet.even when i enable it and change the port to say 5555 i can connect to the web interface using either port 5555 but ALSO on port 80.what's wrong here?the only way to stop that was to create a rule that blocks port 80 on the WAN interface. (btw. could this rule affect LAN users when browsing the web?)

View 7 Replies View Related

Cisco Wireless :: Configure A Wired Guest Network With A Combination Of 5508 And 2504 Wireless Controllers?

Apr 7, 2013

Is there any way to configure a wired guest network with a combination of 5508 and 2504 wireless controllers? I am aware that the 2504 does not have wired guest functionality, however is it possible to set up a wired guest on the 5508 and using mobility anchors, transmit the l2 information through eoip to communicate with the remote vlan?Home built NAC solution, using 802.1x authentication on switchports for public areas. If user is an employee, communicates with the supplicant on their machine, and places them on an internal vlan.If user is a guest, user fails 802.1x check and is placed on a "guest" vlan with an ACL and external DNS.If placed on the guest vlan, the user has to accept a terms of use form.This is working currently with our 5508s without any issue, however we have some remote offices we'd like to roll this out to that are using 2504 controllers. I'm hoping there's a way that I can use the 5508 as an anchor or vice versa to make this work.

View 1 Replies View Related

Cisco :: Guest Access On A 5508?

Jan 25, 2012

We currently tunnel guests to a 4402 that sits behind our firewall and it's been working well for a few years but I am aware that the 4402 is now EoL so I am exploring alternatives:
 
We also have several 5508s deployed and I'm wondering if - in any new guest access config - I can allocate one of its free h/w ports to connect to the firewall, even though the 5508 is configured to use LAG.
 
To put it another way can I configure a new port to a seperate VLAN and not be part of the the LAG'd ports or are you tied to having all ports acting as a group if LAG is switched on?

View 6 Replies View Related

Cisco :: 5508 - MAC Access Control

Nov 29, 2012

We are forced to rush a installation of a WLC 5508 various reasons in a testing lab. I eventually want to configure RADIUS and such but cannot do it at this immediate time. What I would like to do is implement straight forward MAC filtering. The problem I am having is the controller allows either any W LAN or only one W LAN, and a interface setting. I need to have each MAC be able to access several W LAN's but not all of them. Can anyone point me to a article or give me a quick idea of what I can do.I have basic W LAN's configured and have MAC filtering generally working. I cannot just use a user authentication because each user may have 20-30 devices, but not all of these devices should be allowed on all W LAN's and I do not want to rely on the user.

View 8 Replies View Related

Cisco Wireless :: WLC 5508 - Access Via SP

Jan 4, 2012

Today my wlc 5508 crash. after trying to get access via sp. It doesn't responds. so i rebooted. in the sh tech i saw this message which i guess indicates the RC of the failure.   

             Start Cisco Crash Handler Serv              
Sys Name:       usa-5354-wlc-02
Model:          AIR-CT5508-K9
Version:        7.0.98.0
[code]...

Analysis of Failure:   Software was stopped by the reaper for the following reason:
Reaper Reset: Task "locpRxServerTask" missed software watchdog

View 1 Replies View Related

Cisco Wireless :: WLC 5508 Guest Access Via WAN?

Jan 28, 2012

Is it possible to provide wireless guest access over the WAN from another office via the WLC. I have WLC 5508 in a central office and have other remote offices that have one Access Point in each office that are autonomous; I will be converting these to LWAPP. Is it possible to route guest traffic back to the WLC then forward this traffic out to the internet? How would I route this traffic out as well? install a secondary WLC in the DMZ and use anchor points. I only have one WLC

View 7 Replies View Related

Cisco Wireless :: 5508 Get Access To AP Via Radius

Feb 1, 2012

i have configured 35 APs 3502i in 5508 WLC, now i want to get access to ap via radius. Currently i can connect to them via SSH with both user and password set in wireless> access point > global configuration, well, how do i configure the management AP user  through RADIUS?

View 2 Replies View Related

Cisco Wireless :: Guest Access On 5508 WLC

Feb 3, 2013

I'm looking to implement guest WiFi access with web authentication on one of our 5508 WLC (currently deployed within a sandbox environment), but looking for some assistance. The WLC currently has a single connection from port 1 to the 'Test Site 2' switch. This is a dot1q trunk. On the WLC, the interface (for port 1) is configured as follows: [code] Currently, I have one WLAN configured with the profile name 'Guest Test 1', it's enabled and broadcasting the SSID. Security is L3 only with web authentication configured. The WLAN is configured to use the interface names "guest_wifi".
 
The issue is that when a client connects to the WLAN, it receives an IP address okay (10.99.254.x address), but doesn't seem to be able to contact the WLC to get the web authentication page. Eventually, the WLC terminates the connection due to an authentication failure.does it sound like I'm taking the correct approach here? The idea is that clients connect to the guest WLAN, which puts them on VLAN 99 and routes traffic through to the ASA and then onto the internet.

View 13 Replies View Related

Cisco Wireless :: 5508 Access Point Goes Down

Aug 7, 2012

wlc 5508 code 7.0.220.0
AIR-CAP3502E-N-K9
 
each time that for what ever reason my access point goes down(not that my access point resets by itself, if i have to move it), the setting in the vlan mapping  resets to  whatever my native vlan is, in this case 30.

View 3 Replies View Related

Cisco :: 5508 NCS 1.1 Not Showing Any Access Points

Jul 16, 2012

I have NCS 1.1 appliance and added a 5508 WLC running 6.0.199.4 code using snmpv3. Controller is added to NCS, but it doesnt show any AP's which are there on the controller. AP count is zero. I have another controller with code 7.0.230 added and showing AP's though. AP model is 1252.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved