Cisco Wireless :: WLC 5508 - Access Via SP
Jan 4, 2012
Today my wlc 5508 crash. after trying to get access via sp. It doesn't responds. so i rebooted. in the sh tech i saw this message which i guess indicates the RC of the failure.
Start Cisco Crash Handler Serv
Sys Name: usa-5354-wlc-02
Model: AIR-CT5508-K9
Version: 7.0.98.0
[code]...
Analysis of Failure: Software was stopped by the reaper for the following reason:
Reaper Reset: Task "locpRxServerTask" missed software watchdog
View 1 Replies
ADVERTISEMENT
Jan 28, 2012
Is it possible to provide wireless guest access over the WAN from another office via the WLC. I have WLC 5508 in a central office and have other remote offices that have one Access Point in each office that are autonomous; I will be converting these to LWAPP. Is it possible to route guest traffic back to the WLC then forward this traffic out to the internet? How would I route this traffic out as well? install a secondary WLC in the DMZ and use anchor points. I only have one WLC
View 7 Replies
View Related
Feb 1, 2012
i have configured 35 APs 3502i in 5508 WLC, now i want to get access to ap via radius. Currently i can connect to them via SSH with both user and password set in wireless> access point > global configuration, well, how do i configure the management AP user through RADIUS?
View 2 Replies
View Related
Feb 3, 2013
I'm looking to implement guest WiFi access with web authentication on one of our 5508 WLC (currently deployed within a sandbox environment), but looking for some assistance. The WLC currently has a single connection from port 1 to the 'Test Site 2' switch. This is a dot1q trunk. On the WLC, the interface (for port 1) is configured as follows: [code] Currently, I have one WLAN configured with the profile name 'Guest Test 1', it's enabled and broadcasting the SSID. Security is L3 only with web authentication configured. The WLAN is configured to use the interface names "guest_wifi".
The issue is that when a client connects to the WLAN, it receives an IP address okay (10.99.254.x address), but doesn't seem to be able to contact the WLC to get the web authentication page. Eventually, the WLC terminates the connection due to an authentication failure.does it sound like I'm taking the correct approach here? The idea is that clients connect to the guest WLAN, which puts them on VLAN 99 and routes traffic through to the ASA and then onto the internet.
View 13 Replies
View Related
Aug 7, 2012
wlc 5508 code 7.0.220.0
AIR-CAP3502E-N-K9
each time that for what ever reason my access point goes down(not that my access point resets by itself, if i have to move it), the setting in the vlan mapping resets to whatever my native vlan is, in this case 30.
View 3 Replies
View Related
Nov 21, 2010
I'm using a wireless controller 5508 and 1141 Ap.Ultimately all the AP is working as LWAP.Everything is working fine.But offen end user getting "Limited Access " .At that time network is connected but i cant ping even my gateway.
View 7 Replies
View Related
Aug 9, 2012
I am having an issue here. I have 2x 5508 that each have 100 AP license and a little under 200 access points. Basically all of the access points are using DNS to connect to the primary controller that has the DNS entry. Basically half of my access points need to be on the second controller and in order to do this I have been using the high availability mode of each access point to push them to the second controller IP address.It was working perfectly until now. I have pushed 28 access points to the second controller and the last two I need to push at this location just keep resetting on the primary controller. Neither controller is configured as master controller.
View 4 Replies
View Related
Jan 17, 2013
I have access points deployed across several buildings that each have a different IP scheme and their own T1 line. Is it possible to configure the 5508 controller to allow these access points to use the IP scheme assigned for that particular building or will dhcp always assign an IP address to the connecting client based on the IP scheme of the building that the controller resides in?
View 1 Replies
View Related
Jul 13, 2011
I need an official document from Cisco saying the APs models supported by the WLC 5508. Specially, I need to know if the AIR-AP1242AG-T-K9, converted from standalone, will be supported by the 5508.
View 1 Replies
View Related
Apr 11, 2012
I just got a new requirement for our wireless roll out and I need some help. Plan the best way to provide employee and guests wireless access w/ the guests separate from the production environment.
We have a 5508 controller w/ 1142 APs. I have two GBICs in the interfaces (only one is being used). I want to use a back haul connection for the guest access. I am having a hard time in visioning how to physically set up the cabling from the patch panel. Again, the requirement is to not allow guest users to connect to our production network but I still want/need to manage the AP. This will eventually need to be supported for remote sites tunneling back to the primary location.
View 7 Replies
View Related
Jan 16, 2013
After I've upgraded software to the v7.3 and applied AP-SSO it made imposible to access the controller's gui via Service-port. So we tried to access it by management-port, but there is some problem too. It is not working from another subnets. But default gateway on management vlan is set correctly and I even tried to turn of all acl's on switch. WLC is only accessible from the same network. But at the same time wlc is replying on ping fine.All other protocols cannot connect to the controller.
View 3 Replies
View Related
Oct 28, 2011
I am running a 5508 WLC with 10 Access Point. we need to allow Internet Access to Guest. 10MB DSL Internet is dedicated for Guest. This link is terminated on a regular ADSL modem without being part of our network. We want all Guest Internet traffic to reach the ADSL Router. where should I create the Guest VLAN / where the DHCP for Guest users should be created. what is the best practise for similar setup.
Our Network is simple
ISP_Reuter-------ASA_Firewall--------------4505------------LAN-switch 2950
ADSL_modem------------ users connect via wireless but restricted to certain area only.
View 9 Replies
View Related
Feb 19, 2012
What is the OID for the count of the APs connected (and Status UP) to a WLC 5508?
View 2 Replies
View Related
Jul 25, 2011
I have a wireless lan controller (5508) broadcasting 2 SSID's, once is a secure vlan grabbing an ip address from a local dhcp server and getting access to the internal network, and the other ssid is for a guest vlan where the dhcp server is in a remote site and internet access is off a circuit in our data center which is accessed over a wan. The secure ssid's vlan is defined on the local switch, but the guest vlan is not defined on the local switch.the ap's in the respective sites are trunked to the core switch and the switchport config is : [code] it's trunked b/c we have both vlans going across this physical connection.I would like get the guest vlan a wired connection, ie. off a switchhub, but not sure how to do that as this guest vlan is not defined on our local network.
View 1 Replies
View Related
Mar 6, 2013
I would like to start setting up a Cisco Wireless Lan Controller 5508 with some Cisco 1262n AP's. How to start setting this to take advantage of having this wireless lan controller? I have a DHCP server, a Cisco 6509, and Cisco 3750g that connects the access points. I have Vlan 50 for wireless access points.
View 7 Replies
View Related
May 10, 2012
I moved 1242 access point to my new buliding which i have 5508 wlc and 3500 acess point are working. i connected 1242 ap in network it got registered and download new ios and downlaoded the configuration and working fine. But i open the WLC tha 1242 ap are not visible in ap list.
View 3 Replies
View Related
Sep 2, 2010
Access points 1142 controller 5508 running code 6.0.196.0 When you set the access point port speed with "config ap duplex full speed 1000 all" the access points leave the controlle and do not rejoin. I have had to reset the the access points manually with a power down and hold the reset button.
View 13 Replies
View Related
Feb 23, 2012
In my Wireless network, I have two appliances WLC 5508 running version 7.0.116.0.I have a WCS running version 7.0.172.0, deployed on a windows 2003 server.I've imported the two WLCs in my WCS in order to centralize the monitoring and the configuration tasks.Now I'm facing an issue when I want to create a guest user from the WCS, rather than creating this user access on each WLC. The creation of the user account is working good, the replication is done on the both WLCs, but on one of my WLC the guest user account is deleted after one hour(around).On the second WLC, the same user account remains during all its life time.In attachment a screen shot of the advanced parameter of the guest user.You can see that the user was created on the both WLC but is only active on one ... and unfortunately the wrong because the AP is associated with the other WLC.
View 2 Replies
View Related
Apr 22, 2013
Subject: FlexConnect compatibility with Access Point? We have today one Cisco 5508 and those access point on remote sites
o CISCO AIR-LAP-1131AG-E-K9
o CISCO AIR-LAP-1231G-E-K9
o CISCO AIR-LAP-1142N-E-K9
We plan to use redundancy on the controller and implement Flexconnect on the remote site. What we need to know is if I can implement Flexconnect on all actual access point - I think it is possible on 1142N + 1131G but do not know on 1231AG - is it correct or I'm wrong ? We plan to install the latest SW version for 5508 controller.
View 1 Replies
View Related
Mar 10, 2013
I'm having an issue in one open space area with a wifi network.I currently have 5 access points and around 100 users connected to the WiFi.There are desktops, Ipads and Mobile users connected to it.13,24,16,41,9 are the associated users to each access point. The one with 41 and 9 are only 10meters away from each other.
I read on some posts before having issues with APPLE and WIFI so cisco advised to disable the load balancing.I setup the client windown size to 10.On the networks the client roaming is with the default value.On the WLAN the Client Load Balancing is not checked.
View 4 Replies
View Related
Apr 11, 2013
We have an MPLS (layer 3) network 4 offices and a Data center. We are planning to install about 10 Access Points(3600 series) per office and have a controller(5508 series) in the Data center.
Questions:
1- Is this design possible, in other words, just one controller centralizing all Access point traffic in one controller in the Data center?
2- We would like to accomplish this in two phases:
A- install access points without controller handling authentication thru Microsoft IAS servers (current configuration with 1200 series)
B- Deploy wireless Controller in Data center and start migrating orphan AP to Controllers one office at a time.
View 7 Replies
View Related
Oct 24, 2011
have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to directly connect to the service port and disable the global multicast mode. Then two reasons for enabling it are Docs2Go and LanSchool both require multicast to be enabled. I have it enabled on our wired network and it works OK there. ted.
View 10 Replies
View Related
Apr 15, 2012
Interface management on WCL 5508 is assigned ip 192.168.255.200 and from a PC ( on different subnet), i can ping but cannot access https to WCL but From a PC ( in the same subnet) i can ping and https.
View 11 Replies
View Related
Nov 26, 2012
I have problems with an AP AIR-CAP1552C-E-K9 (MAC: 2c:36:f8:73:e8:a0 )this AP cannot join to WLC 5508 software version 7.2.110.0.The AP ever gets associated to WLC.
I saw timeout messages and this error message:
%CAPWAP-3-ECHO_ERR: capwap_ac_sm.c:5656 Did not receive heartbeat reply; AP: 2c:36:f8:73:e8:a0
I don´t see any connectivity issues between the AP and WLC thorugh HFC network.One time the AP join to WLC and I saw this messages in debug CAPWAP:
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Change State Event Response sent to 10.64.128.165:16012
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 CAPWAP State: Run
*spamApTask1: Nov 27 09:01:06.316: 2c:36:f8:73:e8:a0 Sending the remaining config to AP 10.64.128.165:16012
[code].....
View 2 Replies
View Related
Jun 13, 2012
I'm using a Cisco Wireless LAN Controller 5508, 14x Access Points 1041 and 6x Access Points 1031 in combination with a NCS 1.0.
Is it possible to broadcast SSID'S only on defined Access Points, e.g. AP 1-3,7-10,18? If yes, what have I to do?
View 8 Replies
View Related
Sep 17, 2012
In our current Setup we have one WLC 4404 with 100 Access point license, now we have bought 3 number of 5508 WLC each supporting 100 Access point. Our plan is to Migrate all the Access point assosiation from 4404 to 5508. [code]
View 4 Replies
View Related
Sep 24, 2012
I am beginning to get many emails from users who have recently upgraded to OS6 and saying now they cannot connect to our open access wireless network. We use a separate server that users must agree to a user agreement page and they say they get it, but after agreeing, it goes blank and they cannot connect. I am using mostly Cisco 3502's with the 5508 controller using 7.0.112.0 IOS version. Nobody in our IT department has yet to test OS6 yet.
View 9 Replies
View Related
Jan 25, 2013
Installed a new 5508 WLC last week, and finished bringing 68 new 3602i access points online in our College Dorms. We are seeing a lot of "Client De-authenticated" errors "Reason: Unspecified Reason: Code 1. Years ago I asked about error code 1. The reply from Cisco was: "The programers put the code in. It basically means we don't know what the problem is."Got a call from one of the dorms stating that students were getting knocked off the network while going to sites. If a student is wired, network is solid.Walked the dorm in question and was getting full bars of signals at all times, and was able to stream a movie from my Ultraviolet account without any break or slowdown as I moved from access point to access point. So.. my device, an iPad, was fully mobile and did not experience any disconnects.Did observe one student using a MacBook Pro. This student was constantly loosing connection to the access point. Checked the controller for the MAC of the student's computer. I did find deauthentication errors. BUT... this student's error was the computer was receiving an IP address from the DHCP that was already in use. At the computer the error message was a timeout issue.I am just learning the ropes on the 5508. Have used 3 4404s for the past six years.
View 2 Replies
View Related
Aug 30, 2012
I have 50 WAP connected to a WLC 5508. When I backup the config I don't see the custom settings I put in some WAP. Where are the WAP settings saved at ?
View 17 Replies
View Related
Apr 9, 2012
We are having 5508 controller with Lightweight access points 1142, IS it possible to disable 802.11a on certain access points before turning it off completely on the controllers?? Could you provide steps for doing so on WCS?
View 5 Replies
View Related
Mar 13, 2013
I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point? My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
AP001d.4513.dd68#reloadProceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,
[code].....
View 6 Replies
View Related
Oct 31, 2012
I have the wireless controller 5508 and many AP1261 registered on site. It detects a lot of rogue access points around. I would like to find out geographic location of these rogue access points. Is it possible?
View 2 Replies
View Related
Feb 24, 2013
i have a wlc 5508 and 40 access point 1141n there are 1500 users connected with this controller 5508. but when i ping at my gateway ,there is a disturbance in the temp response. [code]
View 1 Replies
View Related
