Cisco Firewall :: 4500 ASA Dropping NAT-T Traffic

Sep 3, 2012

I have an issue where my customer is only using the ASA as their firewall. When their internal users try to connect to a partner's site using a 3rd party IPSec solution it seems as if the return NAT-T traffic is being dropped. However when looking at the traffic the udp500 communication goes through, but the 4500 traffic hits the outside interface and then gets dropped.
 
I used the packet tracer command and the output is set to Allow. Also after initiating the vpn connection I see two udp connections (one for 500 and the other for 4500.
 
I cleared the asp table drop, and didnt see to see anything, I am waiting on the running config, and the customer is running ASA 8.4.
 
I used the capture tool on both interfaces (inside using the client ip, outside using the interface ip, both destined to the 3rd party vpn Headend). Here are the screeshots for this.
 
I went ahead and color coded the ip address. Green is the pre-nat inside Red is the destination for the VPN headend, and Blue is the PAT ip going out.

View 10 Replies


ADVERTISEMENT

Cisco Firewall :: ASA 5505 Dropping UDP / 53 Traffic On Inside Interface?

Jul 21, 2012

We have a Cisco ASA 5505 (v7.2(3)) with a "fairly" normal configuration yet we have a problem where it appears UDP/53 traffic is denied on our inside network.
 
here is output from our sys log:

SyslogID   Source IP      Dest IP    Description
305006      172.18.22.3                   portmap translation creation failed for udp src inside:172.18.22.156/42013 dst inside:172.18.22.3/53
 
To give some clarification:

172.18.22.3      is one of our DNS servers
172.18.22.156  is a device we're experimenting with.
 
We've bypassed the Cisco by using a 4G wireless router with this same device - and it works flawlessly.Here is a [scrubbed] copy of our config. It is what I inherited from the previous admin - I'm not sure of all its finer points (I'm not Cisco certified -- perhaps I'm just certifiable.)
 
: Saved 
:
 ASA Version 7.2(3)
 !
 hostname [redacted]

[code].....

View 5 Replies View Related

Cisco Firewall :: ASA-5510 Dropping Outbound SMTP Traffic?

Aug 21, 2011

A recently added outbound rule has left my SMTP communications broken. I have since removed the rule, and had Cisco do some damage control, but it's still dropping some of the SMTP traffic. I get a number of NDR messages each day like the one below:Your message did not reach some or all of the intended recipients. Subject: RE: Christopher, Curt Sent: 8/19/2011 9:38 AM The following recipient(s) could not be reached:
  
[URL]
on 8/21/2011 9:49 AM
Could not deliver the message in the time limit specified. Please retry or contact your administrator.
<630.SM.Local #4.4.7>
 
Your message did not reach some or all of the intended recipients. Subject: RE: Christopher Curd Sent: 8/19/2011 9:38 AM The following recipient(s) could not be reached:   JWillar@email.com on 8/21/2011 9:49 AM  Could not deliver the message in the time limit specified. Please retry or contact your administrator.  <630.SM.Local #4.4.7>
 
I've attached an image of my configuration (ASDM GUI). The part of the image highlighted in green are the SMTP rules. The part highlighted in yellow is another rule that I added about a month ago to block a SYN attack. This rule may be part of the problem because of the order it is in the list. Not sure, though.
 
I have had two Cisco techs Putty into my ASA to check things out. I think they've done all they can. I wonder at this point if it be wise to just reload the last good running-config I have prior to the Outbound rule being added.

View 13 Replies View Related

Cisco Firewall :: ASA5505 Appears To Be Dropping Traffic For Internal Network?

Jan 10, 2013

we have a Cisco 2901 as a router on a stick for several vlans. Everything on the segment routes fine and accesses the internet just as they should. The 2901 connects to an ASA5505 on port 0/1. Any host connected to the ASA5505 can access the internet, but can not ping into any of the vlans off of the 2901. The strange thing is on either segement of the network I can ping all of the gateways. What is even more strange is when I run wireshark from behind the firewall going into the 2901 I can not see the packet on another wireshark instance behind the 2901. However if I start a ping for a host host behind the asa I can see the packet in wireshark on the host, which I am trying to ping, hit the gateway.

View 15 Replies View Related

Cisco Firewall :: ASA 5505 - Http Inspection Dropping All Http Traffic

May 9, 2012

I am testing out some inspection options on an ASA 5505, and I am running into a situation in which applying a http inspection is dropping all outbound http traffic. I get a "protocol violation" error in the logs.
 
Here is the setup: I'm not sure why the web traffic is getting dropped.
 
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto

[Code].....

View 2 Replies View Related

Cisco WAN :: 4500 / How To Monitor IP Traffic On Switch

Mar 30, 2011

i have a core switch of 4500 series. some system are generating the traffic Extra LAN traffic. how i can monitor on switch that which system is generating the traffic,

View 1 Replies View Related

Cisco Switching/Routing :: 4500 - STM-4 (622) / How To Limit FTP Traffic

Mar 10, 2012

I have the attached setup. now i would like to limit my ftp transfer to 10 mb  from a specific vlan to ftp server on the STM-4 (622) link.  what would be the best way to limit ftp traffic to 10 mb .
 
following is  my switch deatils
 
Video_Main#sh verCisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)Technical Support:

[URL]
 
Cisco IOS-XE software, Copyright (c) 2005-2010 by cisco Systems, Inc.All rights reserved.  Certain components of Cisco IOS-XE software arelicensed under the GNU General Public License ("GPL") Version 2.0.  Thesoftware code licensed under GPL Version 2.0 is free software that comeswith ABSOLUTELY NO WARRANTY.  You can redistribute and/or modify suchGPL code under the terms of GPL Version 2.0.  For more details, see thedocumentation or "License Notice" file accompanying the IOS-XE software,or the applicable URL provided on the flyer accompanying the IOS-XEsoftware.

[code]....

View 2 Replies View Related

Cisco Switching/Routing :: Filter IP Traffic By MAC Address On Catalyst 4500?

Dec 19, 2012

We want to filter IP traffic by MAC address on Catalyst 4500. Since we are using bonding (active-backup mode) we need those mac addresses appear on different ports. Below are solutions that we have tried: ACL but it does not   work since mac acls only match non ip traffic (We CAN NOT use ip acl). Use a static mac address-table entry to ALLOW specific mac addresses. It does not work  either since the same MAC address needs to be seen on a different port. Catalyst 4500 does not support auto-learn option (as e.g. Nexus 5000). 

View 3 Replies View Related

Cisco WAN :: 7609 Dropping Ping Traffic?

Jun 28, 2011

I have a cisco 7609 running IOS version c7600rsp72043-advipservicesk9-mz.122-33.SRE0a.bin with the following modules..
 
sh mod
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  3   20  7600 ES+                               7600-ES+20G3CXL   

[Code]....

The circuit has been tested as clean , so for the moment we have to assume that it is not a circuit issue  We also have another idential 7600 in another POP with similar config that does not display the same problem

View 3 Replies View Related

Cisco Routers :: RV220W - Dropping Parts Of Traffic

May 14, 2013

I have following issue with RV220W - the router seems to be dropping parts of traffic coming through it. The unit is brand new, the firewall is turned off, there are about 20 computers and 15 VOIP phones connected to it via Zyxel GS1910-48; all IPs are set to static DHCP records, in the last 3 hours the router rebooted about 3 times, then I turned on the log in. The router is producing insane number of warnings, as you may see from the log attached. I found this thread [URL] but no answer regarding this issue.
 
Wed May 15 13:03:10 2013(GMT) [rv220w][Kernel][KERNEL] cvm_ipfwd_cache_flow: Failed to allocate flow info buffer
Wed May 15 13:03:10 2013(GMT) [rv220w][Kernel][KERNEL] WARNING:cvmx_ptr_to_phys() passed a NULL pointer
Wed May 15 13:03:10 2013(GMT) [rv220w][Kernel][KERNEL] cvm_ipfwd_cache_flow: Failed to allocate flow info buffer
[Code]....

View 5 Replies View Related

Cisco Switching/Routing :: ASA 5505 Dropping Port 443 Traffic?

May 10, 2012

Networking is not my gig, but it has to be at this very moment.  We have an ASA 5505. Let me explain what's going on.
  
On Tuesday I wanted to be able to use the ASDM since there is less room for error.  But we only had a console set up.  So I ran the following commands...
 
in ($config)   
http      of course didn't do anything incomplete command
http 192.168.1.2 255.255.255.255        didn't anything incomplete command
http 192.168.200.254 255.255.255.255 inside 

[Code]....

Everything started working after that.  Everything worked fine all of wednesday and thursday.  Then this morning it stopped processing again.  When I traceroute it gets to the machine that is hooked up to the console and stops.  So I'm guessing its actually getting to the ASA router and being swallowed up again...

View 23 Replies View Related

Cisco Firewall :: 4500 Enable VPN IPSec Through Firewall

Apr 16, 2011

if y need to enable VPN IPSec through the firewall. y just need to need to allow the port 4500?

View 2 Replies View Related

Cisco Firewall :: ASA5550 - Implement Traffic Shaping / Policing Primarily For P2P Traffic?

Mar 10, 2011

We are looking to implement traffic shaping/policing primarily for P2P traffic. As natively the ASA5550 is only capable of p2p inspection if the traffic is tunneled via port 80 is the AIP-SSM the way forward? We have 2 5550s in active/active failover config. As a side note we are also looking to implement an IDS/IPS system so could this module cover all?Is this module going to provide the desired outcome or is there another module/device out there better suited for this? I would prefer to use the ASA5550s as opposed to implementing another product if only that we can make use of the investment we already made on these devices.

View 1 Replies View Related

Cisco Firewall :: Traffic Limit For Internet Traffic Usig ASA 8.2

Nov 27, 2012

I am testing limit bandwith using my ASA 8.2, i am trying to limit internet access for certains users , i order to save Bandwith for the important things but i can´t get any limitation  
 
My configuration is the following, the acces list is just for my pc in order to test, and the service policy is  applied to outside interface (called internet in my case)  for incoming traffic
  
access-list Internet_mpc_1 extended permit ip host 172.16.127.70 any class-map Internet-class-TEST match access-list Internet_mpc_1 policy-map Internet-policy-web class Internet-class-TEST police output 1024000 1500
  
service-policy Internet-policy-web interface Internet
 
With show service policy i can´t see any activity on the policy , but if i do a similar configuration for inside interface outgoing traffic i can see packets allowed and dropped

View 3 Replies View Related

Cisco Firewall :: ASA 5520 - Allow Traffic From DMZ To Internet And Block Traffic?

Apr 29, 2012

I have an ASA 5520 with the below config
 
Gi0/0: outside (Internet)
Gi0/1: inside (Internal users)
Gi0/2: DMZ (web servers, ftp, Mail etc..)
 
I have a SMTP relay deployed on the DMZ for mailing. I have also a mail servers installed in the internal lan,
 
I want to allow trafic from dmz to reach internal lan, and i want normally also allow stmp relay from dmz to reach Internet.
 
How can i block trafic from DMZ to reach Internal Lan (instead of smtp) if the to allow trafic from dmz to internet i must put ANY in the policy?
 
For allowing trafic from DMZ to reach Internet, the policy must be DMZ -----> ANY ----->Services., this policy means DMZ can implicity reach Internal Lan?

View 2 Replies View Related

Cisco Firewall :: Cat 4500 Translation Creation Failed Message

Aug 1, 2012

Two Vlans (ID1 and 100)are on a Cat 4500, which connects to an ASA, interface DMZ. On 4500, there is default route point to the ASA DMZ interface Issue, server on vlan 100 cannot ping a server on Vlan 1, vice verse. When I enable the realtime log, it gives me a “Translation creation failed” message, please see the attached files.

View 1 Replies View Related

Cisco Firewall :: SSM-4GE Firewall Has 5 DMZ Segments And Specific Segment For Internet Traffic

May 23, 2013

I was asked to enable netflow in an ASA Firewall for Orion/Solarwinds server monitoration. Firewall is a 5550, with 4G RAM, and no extra modules but SSM-4GE. This firewall has 5 DMZ segments and ans specific segment for internet traffic.There are segments as unique subinterfaces in physical interfaces. Other segments as individual subinterfaces in the same physical interface (but individual VLANs)Usually firewall CPU flows between 30% to 40%. Rarely to 50%.
 
1 - How dangerous or risky could be implement netflow in this firewall?...This firewall is very critical for the customer. My concern is regrading CPU, traffic generated, memory, etc
 
2 - In a month, firewall will be migrated from 8.2 software version to 8.4 software version. Is there any incompatibility in some commands?...Would be recommended to perform netflow configuration after software upgrade?
 
3 - How could it be implemented for Orion monitoring, regarding each individual sub-interface (and so, each VLAN assigned)?I there any recommendation regarding configuration, best practices?

View 6 Replies View Related

Cisco Firewall :: 6500 - FWSM - Not Passing Traffic Through Firewall

May 3, 2011

We have 2 FWSM modules in each 6500 switches. 1st module is having 04 firewall vlan groups with 18 vlan interfaces in a single context firewall. All are working fine with no issues. Recently we create one more vlan on MFSC and add into the same firewall module. However newly created vlan inside the FW is not able to communicate with outside and also outside users not able to reach newly created subnet. But within the firewall zones (other interfaces) it can communicate. Once we did packet capture we noticed that its hitting firewall outside interface only and when we ping we got TTL expired error. we have default routes to outside and there's no any route inside as new segment is within the firewall (no any hop).
 
I guess there's no limitation on number of vlans that we can assign on one firewall eventhough there is a limitation for number of vlan-group which is 16 max (but we are within that limit).

View 2 Replies View Related

Cisco Firewall :: Pix 501 Dropping Devices From Network?

Nov 18, 2012

Recently I've pulled a PIX 501 out of a closet (having never been used) and configured it for a VPN with my PIX 506e at an offsite location. This offsite location has a PC, Printer, Access Point, and remote VOIP phone. The VPN itself works great, but periodically the PIX just drops some network devices, specifically the Access Point and the Firewall. Both devices stay off until I reboot it (through an SSH connection) they then spring back to life.
 
PIX Version 6.3(5)
interface ethernet0 auto
interface ethernet1 100full

[Code].....

View 2 Replies View Related

Cisco Firewall :: VPN Setting Keep Dropping On ASA 5510?

Jan 23, 2012

I have a Cisco ASA 5510 firewall, my problem is that when the first VPN connections is established everything is good.  But when that connections is cancel or terminated due to non connectivity.  No one can connect to that firewall through that VPN unless that firewall is restarted.

View 1 Replies View Related

Cisco Firewall :: ASA5505 Dropping Packets

Apr 30, 2013

I am  having an issue where the ASA is dropping packets on the vlan  interfaces. I have it as a dedicated router/firewall for a 100mb connection .
 
Vlan1 is the internal networkVlan2 is the network to cable modem
 
Eth 0/1 is connected to a 2960G switch with hard coded 100mb Full  Duplex at each end, this is the inside interface. Eth 0/0 is the  connection to the cable modem, this is the outside interface, set at  auto at both ends.
 
Im getting on the vlans eg. 51253 packets dropped however network  traffic isnt impacted and everything runs fine, as well as 46532 switch  ingress policy drops.
 
Example;
 
ciscoasa# sh int vlan1Interface Vlan1 "inside", is up, line protocol is up Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec MAC address 70ca.9b36.ab80, MTU 1500 IP address 10.x.x.x, subnet mask 255.255.255.0 Traffic Statistics for "inside": 43250588

[Code]......

View 1 Replies View Related

Cisco Firewall :: 5510 / L2L Tunnel Keeps Dropping?

May 15, 2013

I have our main site using a Cisco 5510 running 8.4.2 code and a remote site using a Cisco 5505 running 8.4.2 code.  The main site has a T1 and the remote site is using a DSL connection.  About every other day I have to reset the connection at the remote site.  The process that I have found that works is to remove the nat statement, clear the cry ips sa and then add back the  nat statement.  The connection usually comes back up and a few minutes.  I am trying to see what is causing this to drop.

View 5 Replies View Related

Cisco Firewall :: ASA 5505 Connection Dropping

Jun 23, 2012

I have a Cisco ASA 5505 - 50 VPN edition.  I have baffling network issues that I have not been able to pinpoint and I recently started to think it may have something to do with my ASA.  I'm a network administrator and I have a Cisco ASA 5505 in my home network so I can learn how to manage Cisco ASA's and utilize the Easy VPN feature so I have a always on VPN connection into work to log into servers, etc.  I've been using the ASA for almost 6 months with the EasyVPN feature with no issues.  My ISP is Comcast.
 
Within the last week my connections have been randomly dropping for about 20 seconds and then reconnecting.  I have two computers on the network that have a direct ethernet run to the switch ports on the back of the ASA.  When the connection drops, I see my LAN icons completely lose connectively (yellow exclamation warning) then after 20 seconds, reconnect.  This is very random.  I was able to get it to happen every time I connected to XBOX live and play a online game.  It would almost on cue drop after 30 minutes of online gamming.  Here are the steps I have taken:
 
1. Replaced 10/100 switch to a brand new 10/100/1000 switch from computer run in my office to the ASA.
no joy
 
2. I upgraded the ASA to the most recent firmware: ASA Version 8.4, ASDM Version 6.4
no joy
 
3. I had an ethernet run under my carpet to the office, I started to  think that maybe one of the cables had an issue after walking on it and  vacumming causing a short.  I removed all the ethernet under the carpet and installed power line over ethernet adapter from the ASA to my office.
no joy
 
4. I checked both computers on the network for viruses.  All computers came back clean after scanning wth Malwarebytes and SuperAntispyware.
 
5. I've watched the logs on the ASA as the LAN connection drops and I don't see error messages to troubleshoot this issue.
 
The only thing left to replace is the Comcast modem or the Cisco ASA.  The Comcast modem is newer and only about 1 year old (rented from Comcast).  Since my actual LAN connection drops and I lose connectively I believe there may be some issue with the ASA or the ASA switch ports or some sort of internal hardware issue on the ASA.

View 4 Replies View Related

Cisco Firewall :: ASA 8.2.4(4) Seems To Be Dropping Valid TCP SYN Packets?

Feb 28, 2012

We have a setup with a MS-TMG - ASA (8.2.4(4) in routing mode) - (internal) Router - FWSM - Router - Exchange with NLB.  We have now the problem that IMAPS is not really working through this setup. It works from internal (without ASA and TMG inbetween), but not reliably through the internet. There is a rule on the ASA which permits the ports from the TMG to the Exchange NLB address.We opened a case with Microsoft and they told us that not all tcp-syn packets are received by the Exchange server which were sent by the TMG.Thus I sniffed on the ASA with a packet capture and indeed, a lot of syn packets were on the interface to the TMG, but not anymore on the interface to the internal router.This ASA also filters all other internet<->company traffic, so there's a lot of stuff running.
 
Maybe it's dropped in the ASP, or is the capture maybe not valid?Here the show asp drop:

ASA01-Internet# sh asp drop
Frame drop:  Invalid TCP Length (invalid-tcp-hdr-length)                                  1  Reverse-path verify failed (rpf-violated)                                  319  Flow is denied by configured rule (acl-drop)                            477077  First TCP packet not SYN (tcp-not-syn)                                   10212  TCP data send after FIN (tcp-data-past-fin)                                 41  TCP failed 3 way handshake (tcp-3whs-failed)                               824  TCP RST/FIN out of order (tcp-rstfin-ooo)                                 1419  TCP SEQ in SYN/SYNACK invalid (tcp-seq-syn-diff)                             6  TCP SYNACK on established conn (tcp-synack-ooo)                              1  TCP packet SEQ past window (tcp-seq-past-win)                              821  TCP invalid ACK

[code]....

View 9 Replies View Related

Cisco Firewall :: 515e / Traffic Not Passing Through Firewall?

Jan 16, 2013

Ive got a problem with passing traffic through a Cisco 515e firewall.im trying to telnet to devices on the inside net, 172.16.x.x fom an outside net 10.x.x.x? ive configured a group called infrastructure and added the 10.x.x.x addresses.ive configured acl 101 inbound on the outside interface:

access-list 101 permit tcp object-group INFRASTRUCTURE any eq telnet
 
theres a route to the inside net:

inside 172.16.0.0 255.255.0.0 172.16.163.1
 
and theres a translation:

static (inside,outside) 10.4.4.34 10.4.4.34 netmask 255.255.255.255
 
when i try and connect, using a packet capture  I can see traffic from 10.4.4.34 to the inside device 172.x.x.x on the inside interface but i cant see the traffic leave the outside interface ive used the same group infrastructure group before to connect to VM machines on the 172.x.x.x net on RDP and this wrks ok. access-list 101 permit tcp object-group INFRASTRUCTURE object-group VMs eq 3389

View 8 Replies View Related

Cisco Firewall :: 172.16.10.1 / Allow Traffic Through Firewall To DHCP Server

Jun 11, 2013

My setup is as below
 
inside host--> ASA1--Outside interface- layer_ 2_Switch1--outside interface--> ASA2--inside interface-DHCP SERVER.
 
We want that inside host should get ip from subnet 192.168.10.0 /24. This ip pool is configured in DHCP server (ip 172.16.10.1) which is connected to ASA2. There is no routing issue as we are able to ping DHCP srever 172.16.10.1 from ASA1. to do config needed on  ASA1 and ASA2 , so that host connected to ASA1 inside interface can get ip from DHCP srever. We have configured 192.168.10.1 /24 to ASA1 inside interface which will be gateway to inside host of ASA1.

View 6 Replies View Related

Cisco Firewall :: ASA 5520 - VPN Traffic Is Getting Dropped Through Firewall

Apr 8, 2011

Our Local Network is behind the CISCO ASA Firewall.Whenever we are accessing to Client VPN server,it is getting connected but after few Minutes (May be 5/10/30 Min),the sessions are terminating. The same traffic through PIX is no issue , only with ASA Firewall. See the following Error and request you give the possible root cause for this.
 
2011-04-09 16:15:09    Local4.Info    172.16.1.68    %ASA-6-302016: Tear down UDP connection 87447908 for OUTSIDE:68.22.26.66/4500 to inside:172.16.9.10/4410 duration 0:27:49 bytes 18653

View 1 Replies View Related

Cisco Firewall :: Dropping Important Connections On 887VAMG?

Mar 5, 2012

I've got a problem on 887VAMG router. It drops important connections. As customer wants to have a firewall I created ACL and ip inspect rules ,but the router drops their connections to cloud and some websites are not opening. So I removed ACL and most ip inspect rules just to test if it effects that. And left only ip inspect http urlfilter. But still they have those problems, so I'm really stuck how to configure that firewall. The below some dropping connection review:
 
%FW-6-DROP_PKT: Dropping tcp session  due to  RST inside current window with ip ident 13968 tcpflags 0x5014 seq.no 1629693318 ack 1687676045
000049: Mar  6 11:49:21.324: %FW-6-DROP_PKT: Dropping http session <ip>:1766 69.171.242.12:80    with ip ident 26247 tcpflags 0x5018 seq.no 264144210 ack 642133125
000050: Mar  6 11:50:00.774: %FW-6-DROP_PKT: Dropping http session <ip>:4708 69.171.242.12:80    with ip ident 2425 tcpflags 0x5018 seq.no 3819869211 ack 1862176018
000051: Mar  6 11:50:52.515: %FW-6-DROP_PKT: Dropping http session <ip>:2599 173.194.34.90:80  due to  RST inside current window with ip ident 22909 tcpflags 0x5014 seq.no 899975979 ack 92642430

[code]....

View 1 Replies View Related

Cisco Firewall :: 871 - Default Class Map Is Dropping All Packets

Aug 21, 2012

I have a Cisco 871 router that used to have Access list based security. now I am trying the ZBFW for the first time.  I thought I had a pretty good program until I found all my traffic was getting dropped. This is my first stab at ZBFWs and I am a bit confused esp with the default class part.
 
The router is for my house and thus also has to have priority for gaming. I will add the gaming and voice QOS once I get it working,
 
Guest VLAN has access to 2 IP's in Data for printing. Cisco871#sh run

Building configuration...
  
Current configuration : 8005 bytes
!
version 12.4
no service pad

[Code].....

View 1 Replies View Related

Cisco Firewall :: ASA5505 Dropping TCP Connections For Email With Attachments?

Jun 23, 2011

6Jun 24 201118:08:44209.85.213.5458623174.141.xx.xx25Deny TCP (no connection) from 209.85.213.54/58623 to 174.141.xx.xx/25 flags RST on interface outside I am getting this error in my asdm logs whenever I try to send an email with an attachment. Regular email go through fine. If I send a 1mb file it seems to go through after several attempts. If I send a 5mb file it might go through anywhere between 4-15 hours. It doesn't matter where I send from. Sometimes it will say ACK or RST ACK on interface instead of RST. The ASA is running 8.3.1 code. I have tried inspect ESMTP and removed it, tried sysopt connection timewait. I am at a loss.

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Dropping Internet Connection Randomly

May 24, 2012

One of our hospitals keeps reporting that their internet is going out for a while than comes back up, sometimes they even have to reset the ISP modem for this it to work again. I upgraded and switched ISP to Time Warner Cable and figured it would essentially solve the issue, but there are still reports of internet outage and our new ISP has confirmed multiple times that their end is still up. Our ASA 5505 was configured by a previous employee, but when looking at the running config I noticed that the Interface for our ISP is NOT set to Duplex Full and Speed 100.

interface Ethernet0/5

switchport access vlan 2

View 3 Replies View Related

Cisco Firewall :: ASA 5505 - Dropping TCP Connections On Inside Interface

Feb 12, 2013

Trying to add inside routes on an ASA 5505 to point traffic to another gateway for other connected networks is resulting in the following error 6Sep 16200 819:13:5810601510.184.236.1265003810.170.54.1823389Deny TCP (no connection) from 10.184.236.126/50038 to 10.170.54.182/3389 flags RST on interface insideI believe the problem is due to the Asymetric tcp connection and the ASA is dropping the connection because it only see one half of the traffic.Is there a way we can stop the firewall dropping the TCP connections on the inside interface? i've tried removing the threat managment which didnt work.Annoying thing is were putting the ASA 5505's in to replace old Watchguard soho firewalls only the watchguards forwarded the traffic no problem at all.

View 1 Replies View Related

Cisco Firewall :: PIX 525 - Windows Server 2008 And PIX Packet Dropping?

Sep 6, 2011

I came across a situation where a client had an old PIX 525 running PIX 6.2.  There was a Windows 2008 R2 server running Exchange 2010 that was having trouble delivering email to a handful of email servers.  We then found out that we could telnet to these servers on port 25 but got no return traffic.  We then went back the old email server that was running Windows 2003 Server and could telnet to port 25 on these email servers and got a response, saw the banner and could issue commands.  The first thought was reverse DNS which we thoroughly checked and it was not.  I turned off the smtp fixup protocol and that didn't fix it either.  From workstations on the network running XP or Windows 7 or Linux you could telnet to these servers and you would get a response but just not with 2008 server.  I spent hours on the phone with Cisco support and it was determined that the packets were returning and we could capture the packets on the outside interface but they were then dropped by the firewall.  Using the 6.2 version of PIX we could not determine why the packets were being dropped.  I suggested upgrading to the next major version to be able to troubleshoot the issue further.  We then upgraded the PIX to version 7.0(8).  After the upgrade we were able to telnet to the problem mail servers from Windows 2008 Server and there were no issues. Is there a know issue with Windows 2008 Server and PIX 6.2? 

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved