I have a Cisco ASA 5505 in my home office which has a few PCs behind it with a linux web server running some websites. I can access the websites from outside no problem (i.e. on my iPhone using a 3G connection). However, I struggle to access the websites from within the network. The ASA gives me this error: [code]
View 3 RepliesWe have Cisco ASA 5505 with ASDM 5.2 We have one Proxy server in our Local Lab and pointed to Hosted service(Simple Signal)issue is, When our proxy server send register to hosted server, ASA change private IP and post with outside IP and src port as 1063 every time.
Here is debug log on real time monitoring.
Aug 24 2011 05:21:19 302015 203.xxx.xxx.226 192.168.1.51 Built outbound UDP connection 3774 for outside:203.xxx.xxx.226/5060 (203.xxx.xxx.226/5060) to inside:192.168.1.51/27014 (99.119.161.107/1142)
Aug 24 2011 05:21:19 607001 203.xxx.xxx.226 Pre- allocate SIP Via UDP secondary channel for inside:192.168.1.51/27014 to outside:203.xxx.xxx.226 from REGISTER message
Aug 24 2011 05:21:19 710005 203.xxx.xxx.226 99.xxx.xxx.107 UDP request discarded from 203.xxx.xxx.226/5060 to outside:99.xxx.xxx.107/1063
Here 99.xxx.xxx.107 is Our ASA Outside IP address 203.xxx.xxx.226 is Hosted server IP address. My ASA config is attached.
I need configuring RDP access to my local server from a remote location on my Cisco ASA 5505 Firewall.I have attempted to configure rdp access but it does not seem to be working for me. How to modify my current configuration to allow this? I need to allow the following IP addresses to have RDP access to my server: [code] The other server shows up as 99.89.69.334 but is working fine.
I already added one server for Static route and RDP but when I try to put in same commands it doesnt allow me to for this new one. My configuration file and what are the commands i need in order to put this through. Also, if there are any bad/conflicting entries. Also I have modified IP information so that its not the ACTUAL ip info for my server/network etc... lol for security reasons of course.Also the bolded lines are the modifications I made but that arent working. [code]
I like the ASA 5505 for SMB and Home Offices very much, but I'm missing sadly a DNS Server or at least the ability of the DHCP Server to use static addresses for certain MAC's. In SOHO's the ASA is the only thing always powerded on and often even a Server where a DNS Server could be installed is missing.So is there a chance to see such a feature (DNS Server and/or static DHCP) in the next SW Release? how name resolution in a small LAN can be done without a local DNS Server?
View 3 Replies View RelatedI am configuring remote access vpn on ASA5505.Everything is working fine so far, except when the client got connected, it still used the local DNS server provided by the ISP. How do I force the client to use the DNS server configured on ASA?
View 7 Replies View Related I ran into a very interesting problem that occurred today and I'm trying to figure out why it happened. If it was one ASA 5505 that just required the reboot, then I'd have just chalked it up to a glitch, but when we built a new AD/ DNS server on the main network at the main site and changed the 3 Remote site ASAs to point to the new DNS server in the DHCPD options, none of them could ping any local host names to the DNS server at the main site they were now pointing too, but external host names { URL} all translated and pinged fine.
From a laptop on one of the remote sites, we could ping the new AD/DNS server(192.168.0.3) and the old AD/DNS server(192.168.0.2) and everything else at the main site, and telnet to port 53 showed successful across the Easy VPN from the Remote site to the new server at the main site. When wire shark was added to the new DNS server at the main site, the DNS request and replies for {URL}, for example, came and worked fine, but any requests for local resources never made it to the server from the remote sites.
A reboot of one of the Remote Site ASA's corrected the issue. Then I rebooted the other two remote site ASAs, and now DNS was working fine for everybody. I had also tried clearing the ARP cache on the ASAs before resorting to rebooting them. I also tried rebooting the laptop thinking the local DNS cache needed cleared before resorting to rebooting the ASAs. I'm struggling to understand why external, public host names made it through and resolved from the remote sites to the new server at the main site, but anything local failed before even reaching the new server(The new DNS server could resolve requests made by computers at the main site, but the remote sites that traverse the Easy VPN from the ASAs failed). The new AD/DNS server is the only server configured for DNS for all remote site computers.
Is any of this making sense? I'm wondering if clearing the x late or local host tables would have corrected it without having to reboot. I'm just trying to grasp the understanding here and figure out what happened.
Here's my setup:
- Cisco 1841 connected to the internet on fa0/1
- LAN connected to fa0/0/1 (switch port, connected to Vlan1)
On my LAN I have a web server that houses different websites. Those websites have DNS records that point to my public IP address, located on fa0/1. From the outside I can reach the websites perfectly, but I can't reach them from the inside. So it looks like I can't seem to connect from my local LAN address to the public ip address on the Cisco (who then should NAT it to the correct server)
Here is a snippet from my config:
--NAT--
ip nat inside source static tcp 192.168.0.3 80 interface FastEthernet0/1 80
ip nat inside source route-map Internet interface FastEthernet0/1 overload
--OUTSIDE INTERFACE--
interface FastEthernet0/1
description WAN
ip address dhcp
ip access-group WAN-IN in
[ code]...
--INSIDE INTERFACE--
interface Vlan1
description LAN
ip address 192.168.0.254 255.255.255.0
ip access-group LAN-IN in
[Code]....
I have a customer who is going to host a VOICE services like providing SIP services to its customers. What specific ports required to be opened up for this on ASA 5515X. I would rate it ASAP.
View 3 Replies View RelatedI found an interesting manual at this forum for blocking websites whits local content filtering. After I've modified the variables to get more details, I stopped at on question. My current Problem is "zone-pair.
zone security Z-SECRUTIY-SOURCE
zone security Z-SECRUTIY-DESTINATION
zone-pair security ZP-SECURITY source Z-SECRUTIY-SOURCE destination Z-SECRUTIY-DESTINATION
service-policy type inspect CM-INSPECT-TRAFFIC
[code]...
We have a Cisco ASA 5505. As of yesterday we could no longer access our web server (the web server is hosted off-site). Pinging the DNS address and direct IP (from the firewall and a PC) both return no response. Pinging the IP from the T1 router responds properly, meaning the router can access the web server, but the firewall cannot. Accessing the web server has never been a problem, and no configuration changes have been made to the network/firewall. Other locations can access the web server just fine.
View 1 Replies View RelatedI have a cisco asa 5505 firewall. Is it possible to block secure websites in it like [URL]? I have already tried regular expression filtering but it filters only http traffic.
View 4 Replies View RelatedI would like to allow users from network 10.132.23.0/24, 10.132.33.0/24, 10.132.24.0/24 access to our SQL server(192.168.1.7) located on the inside interface(192.168.1.0/24 network) Those networks (10.132.0.0/16) come from the DMZ interface.
View 12 Replies View RelatedI tried the solution posted at [URL] however it did not work on my ASA5505 8.4(2). I thought that it may be because I only have a single public address so the web server is responding to port forwarding through the one public IP already. looking in ASDM it appears to indicate that a configured access list is blocking the server from responding to the internal hosts.
object network Private_IP
host 192.168.1.15
object network Public_IP
host 1.1.1.1
object-group network internal_net
[code]....
Can I fix an access list (or something) to make this work or am I wishing for too much with only one public IP? This worked by default on my Netgear firewall.
I would like to allow remote access to a windows server through a ASA (5505) firewall. Users will use the vpn connection in order to connect to a private network. Is there any link that describes the steps for ASDM?
View 3 Replies View RelatedI just purchased a domain name, that I have forwarding to my WAN address. I want to be able to access my home websie via this route. I have an ASA 5505, how do I get the ASA to point to the home server when the WAN IP address is entered?
View 16 Replies View RelatedI'm having trouble setting up the correct rules on an ASA 5505 I'm using in my home office. I have a couple of IP Cams I need to access remotely.
I've tried setting up simple NAT(PAT) and/or Access Rules, but it hasn't worked. I have a single dynamic IP for the Outside interface. Call it 77.76.88.10 and I am using PAT. The CAM is setup to connect on port 80, but could be configured if necessary. I've tried setting up NAT Rules using ASDM as follows:
Match Criteria: Original Packet
Source Intf = outside
Dest Intf = inside
[Code]....
I'm afraid to use CLI only because I am not confident I'll know how to remove changes if I make a mistake.
When I start a VPN-session my server looses internet access. The server is host for a few virtual machines and they have internet access.using 5505 and asa is version 8.4(2). [code]
View 6 Replies View RelatedIm trying to configure remote access VPN on ASA5505. I configured it as local CA server, installed digital certificate on remote station and everything looks fine as far as i can see. I'm using cisco VPN client 5.0 on remote station. when i initiate VPN session it fails while trying to connect. Looks like im missing some configuration but i cannot figure out what it is. Currently i have firewall configured to use group authentication and everything works fine. I want to switch it to use certificate authentication, and if possible, confiure firewall to use main mode instead of aggressive mode for better security.
View 4 Replies View RelatedI just installed a Cisco ASA 5505 in my company's network,however the network became so slow and many websites cannot be opened or it takes toolong to open (yahoo, hotmail etc.) resulting to a request time out sometimes.
Here is my configuration:
ASA Version 8.2(1) !hostname xxxxxxenable password xxxxxx encryptedpasswd xxxxx encryptednames!interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 !interface Vlan2 nameif outside security-level 0 ip address
[Code].....
I was using a wrt54g previously, and host my own webserver, including my own DNS server. I used port forwarding to forward the web traffic to that computer. Well my family got me a new EA3500 as my old one would continually stop working.Since changing router when I duplicate the port forwarding setup from old to new, all the web browsing dies. My web server has now been offline for a few days, and I'm frustrated beyond belief now. I know I've seen the previous posts saying to never forward port 53 (DNS), but I'm at a loss why I could with my old router, but it's now the end of the world with this new one.
View 9 Replies View RelatedWe have 2mbps leased line and have Cisco 1841 which is managed by our ISP. I have hooked up another 1841 (please find basic config below, it will get more complex lateron) Now when I connect my laptop I am able to browse Internet. But when I conect VOIP phone, it is not able to contact it's Hosted Server on Internet.
VOIP phone is Polycom SoundPoint 550 and I get URL call disabed message. If I try netgear Firewall everything seems to work.that the voip provider needs following ports UDP Range 16384 - 32766, TCP 5060 & UDP 5060. But in my config all outbound traffic is allowed. [code]
I have a PIX 501 with 6.2 FW. The firewall inside network is connected to a Windows server (Mailserver). I can get access to most websites on all clients as well as on the server. However, there are some particular websites, such as facebook.com that the server and all but one client cannot access. I get a "cannot display the webpage" in internet explorer.
I have disabled the Windows firewall and AV. I have also scanned for any malware and no malware was found.
I found on the forums a "fixup protocol dns" solution, but my PIX version does not support it.
Below is my config:
PIX Version 6.2(2)
nameif ethernet0 outside security0
nameif ethernet1 inside security100
[Code]......
i have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration
ASA Version 8.2(1)
!
!
interface Vlan1
[Code].....
i have configuration my network infrastructure with the asa5505 like on image. i want that my users from lan 10.13.10.0/24 can to access to my LAN 192.168.0.0/24. can i use just routing or i must to use site to site VPN. how can i do it? how configure my asa 5505.on my LAN1 there's DHCP. From LAN side of my asa5505 i must disable DHCP.In my LAN1 i have DNS,Domain Controller. The users from my LAN3 need to access to LAN1 because of authentication and access to resources and programs. i attached my picture with configurtion.
View 2 Replies View RelatedI have, what I believe to be, a simple issue - I must be missing something. Site to Site VPN with Cisco ASA's. VPN is up, and remote hosts can ping the inside int of ASA (10.51.253.209). There is a PC (10.51.253.210) plugged into e0/1.
I know the PC is configured correctly with Windows firewall tuned off. The PC cannot get to the ouside world, and the ASA cannot ping 10.51.253.210.
I have seen this before, and I deleted VLAN 1, recreated it, and I could ping the local host without issue. Basically, the VPN is up and running but PC 10.51.253.210 cannot get out
ASA Version 7.2(4)
!
hostname *****
domain-name *****
enable password N7FecZuSHJlVZC2P encrypted
[Code]...
We've a Cisco ASA 5505 connected directly to Verizon FiOS Circuit (ONT) box using Ethernet cable. As per the existing documention that I have, the previous configured this as a dedicated router to establish a seperate VPN connection our software provider. They assigned both Public Static and Local Static IP address. When I try to ping the public IP address, it says request time out; so the public IP address is no longer working.
When I ping the local IP address of 192.168.100.11, it responds. The SolarWind tool also shows Always UP signal. How can I login into this router either from remotely or locally to check the configuration, backup and do the fimrware upgrade?
I also tried to connect my laptop directly to the ASA 5505 router LAN port. After 3 minutes, I'm able to connect to Internet without any issues. However I don't know the IP address to use to login.
I'm having trouble setting up local LAN (reach inside network when VPN connected) and Internet access (reach internet when VPN connected) for my VPN CLients when they are connected to my VPN, They can connect, no problem there, but I can't reach any resources when connected. My pings time out, both to my inside network and to public ip adresses, the only thing I'm able to ping is my ASA (172.16.30.1), and I don't se any routes under "Status/Statistics/Route Details" in my cisco VPN Client (when connected).
Here's my config
ASA Version 8.0(3) !hostname KardesASAdomain-name default.domain.invalidenable password XXXX encryptednames!interface Vlan1 nameif inside security-level 100 ip address 172.16.30.1 255.255.255.0 !interface Vlan10
[Code]....
Has ASA5510-K8 as firewall, has access rules setup for restricted PCs: [code] permitOn those PCs, users can only browse the websites that are in favorites, but some of them are working, some are not.Test on unrestricted PC, websites that can’t be accessed from public PCs can be access on regular PCs , either by address or IP.Checked GPO setting, don’t see anything wrong there.
View 4 Replies View RelatedI am having an issue where I cannot access certain files on websites. It looks as though the files are accessed via ftp. Could my router be blocking it. I have a Cisco 2801 router acting as a firewall.
View 13 Replies View RelatedI have a problem with PIX 506E that meets the version 6.1, and in an simple computer network equipment seems to behave in strange ways because some web sites do not open or very open slow thereby its operation impracticable. On the other hand other web sites open normally.
Querying the web site of the Cisco, I found several documents discussing the same problem but in a later version ( 7.0 ), not in this version 6.1.
I've tried removing the pix from the network , not the error occurred, again insert pix however tested only with a machine, without the rest of the network and the problem persists
We are using several Cisco ASA 5505 with the 8.05 OS on it. The problem is that the SMTP traffic of my ISP(Telenet) isn't passtrough the ASA, I'm using outlook 2010. Before there was also a problem with our local exchange server but I solved this by disabling ESMTP checking in the policies, but it didn't worked for my local ISP.
View 4 Replies View RelatedWe have a Cisco ASA 5520 and Web sense. I added a filter but it seems like it is still not allowing us to access a certain website from most of the machines however some machines with the same configuration work on the DMZ. Accessing website tells us:
"Firefox has detected that the server is redirecting the request for this address in a way that will never complete".
Filter I applied on the firewall:
filter url except 0.0.0.0 0.0.0.0 64.18.218.0 255.255.255.0 allow
filter https except 0.0.0.0 0.0.0.0 64.18.218.0 255.255.255.0 allow
I have an configuration of ASA 5510:
ASA5510# show run
: Saved
:
ASA Version 8.3(1)
!
hostname ASA5510
domain-name lohoi.local
[Code]..
When i configure to block websites it's ok, but websites unblock to access very slowly, sometime i can't access. My company has 50 users, all most them can't access unblock sites. How can i configure it better?