Cisco Firewall :: 5585 Configuration BVI Transparent FW And VLAN

May 28, 2013

I have a problem whit the configuration of a Firewall ASA 5585 whit the BVI Interface and transparent Firewall, I have 2 VLAN that i want to interconnect.

The problem is whit the configuration of VLAN. The traffic does not cross the FW.

View 1 Replies


ADVERTISEMENT

Cisco Firewall :: 5585 / Have Context In Transparent And Routed Mode?

Apr 24, 2012

Is it possible to have context in transperant mode and routed mode. Means if i need three context then 2 of them is in routed mode and one of them is in transperant mode. If yes then how, i can 't find this info in cisco website.?I am havin 5585-x and asa version 8.4?

View 8 Replies View Related

Cisco Firewall :: ASA 5585 Transparent Mode With Multiple Contexts

May 6, 2013

We are deploying the Cisco ASA 5585 in transparent mode with multiple contexts, the port-channel was configured to connect to the core switches using  dot1q trunk. We are experiencing an issue which is the core switches are configured loop guard globally, therefore the port-channel connected to the firewalls will be put into inconsistent state when the failover happen, and the two firewalls' failover can not fulfill the failover at last.
 
I have two queries below: 

1. Does the firewall allow the BPDU passing through when it is in standby mode, for example, secondary firewall is active for group 2 and standby for  group 1.  does the secondary firewall block the BPDU from the vlans under group1 ?   
2. Can we disable the loop guard feature on the switch port-channel or is there any other way to solve this issue ?

View 1 Replies View Related

Cisco Firewall :: QOS Configuration On ASA 5585?

Nov 29, 2011

I want to configure Qos for 2 diffrent Vlan 2 , each vlan for 2 mbps bandwidth .(VLAN details VLAN 10 (10.10.x.x /24) and vlan 20(20.20.x.x/24) Is any difference regarding initials configuration B/w ASA 5520 and 5585

View 9 Replies View Related

Cisco Firewall :: Pass Management VLAN Traffic Through ASA 5510 In Transparent

Mar 10, 2013

We have a small cisco 1800 series workgroup router that seperates our network from the outside world.  The data coming into our network goes into the router on interface fa0/1 and comes out on interface fa0/0.  fa0/0 is split into 2 sub-interfaces (fa0/0.2 and 0/0.3).  These sub-interfaces correspond to a desktop and server vlan on our network.  The workgroup router is connected to a 3560G trunk port (we'll call it switch 1) and switch 1 connects to another 3560G (we'll call it switch 2). Recently I was asked to add another layer of security to our network by installing an ASA 5510 firewall and forcing certain types of traffic to authenticate using their domain credentials for our network.  The firewall was set up between the router and switch 1 in transparent, multi-context mode.  There are 2 security contexts, 1 for the desktop vlan and 1 for the server.  Both have the same security settings applied to them since we want the same behavior regardless of whether they are trying to access the servers or the workstations.

View 2 Replies View Related

Cisco Firewall :: ASA 5515 Transparent Mode / Multi Context And VLAN?

Jun 1, 2013

On ASA  5515  it shows it is in transparent mode  and it has multi context.As in transparent ASA  we know it has single Management IP address.This ASA is connected to  one switch  on two ports gi2 and gi3.One port carries vlan say 800  to the ASA.Other port carries vlan 500 from the ASA  to switch But when i log onto ASA  and do sh run it shows no VLan info there.

View 3 Replies View Related

Cisco Firewall :: Configuration Required For Transparent Firewall ASA 8.2?

Mar 31, 2013

I have one firewall need to be configured in transparent mode. I have inside and outside router. What is the configuration of transparent firewall ASA8.2. I didn't find the configuration on Cisco site.

View 17 Replies View Related

Cisco Firewall :: Transparent Firewall Configuration In PIX 515E

Nov 25, 2012

I am trying to set the PIX firewall to transparent mode.After I set it to transparent firewall, I allowed all icmp, tcp, udp traffics.Currently, any devices in the inside network can get the ip automatically from DHCP server in the outside network but cannot ping to any servers in the outside network either access the internet.Do I need additional confiration on the firewall?
 
Here's the configuration:
 
PIX Version 7.0(1)
firewall transparent
names
!
interface Ethernet0
[Code]....

View 1 Replies View Related

Cisco Firewall :: ASA 5505 Transparent Firewall Configuration?

Sep 11, 2007

I want to configure an ASA 5505 in transparent mode (7.x). Somehow, I got it to work.. but i need some kind of step by step description. I just want to connect it with outside on a route .. inside in my LAN. Its working now with one ASA. But in the Web Interface the Interfaces inside and outside are down.. but its working.

View 5 Replies View Related

Cisco Firewall :: ASA 5550 Transparent Active / Standby Configuration

Dec 20, 2012

I am in the process of adding a new ASA 5550 as a standby box to an existing ASA 5550 running on transparent mode. Both are on version ASA 8.0(4) and ASDM 6.2(1). I have set the new ASA 5550 to transparent mode. The configurations are the following for the HA: [code]My questions are the following:

1. The management ip address is different than the ip used for the failover link. Since the firewalls are on transparent mode, does the failover ip needs to be the same as the management ip address?
 
2. Does any other additional config is needed for HA to work for basic active/stand-by failover?
 
3. Which is the best method to add the second box without disrupting the active box?

View 3 Replies View Related

Cisco Firewall :: 6509 / FWSM VLAN Configuration Mismatch And Some VLAN Deleted

Aug 12, 2012

We  have 6509 VSS with FWSM Module and we have created two context on it, one is INTERNALL CONTEXT othe is EXTERNALL Context? We have spanned various VLANS in switches and FWSM context level.  All VLAN Gateways are configured in context level.
 
Activity description : We had planned migration of these devices into a new Datacenter, it was a planned activity. During  migration of devices from one Dc to a new DC  we broke the VSS and kept the primary running and removed the secondary switch and migrated this secondary to new DC  and powered this device ON in the new DC and checked all the config was very much fine but this device was OFF network as secondary was brought to new DC just to limit the downtime during the primary switch movement.
 
During the activity ( Primary switch movement )We powered off the Primary switch  and mean time before shifting into new Data center  We had brought up secondary switch which was already existing in the DC was put live in the network and it was working fine without any issues.
 
Later  we had moved  Primary into new data center and tried to put into VSS with the secondary , during this period the secondary device into went into RECOVERY MODE  and  primary device was not responding and devices  went off network and immediatly we  removed the VSL link and brought up  primary into production network without secondary online in the network ( Without VSS just stand alone switch ) network started working, but bringing up the primary we found that some of the VLANS in the FWSM was deleted and some VLAN had misconfiguration ( example : say original  VLAN  ip 10.200.112.1 has become  10.300.13.1 ) also some of the access list as well as SVI was deleted making configuration mismatch.
 
Wanted to know while syncronization b/n primary and secondary switch in VSS if we pull out VSL link would create this type of issues.

View 1 Replies View Related

Cisco Firewall :: ASA 5515-X Vlan And IPS Configuration?

Oct 10, 2012

i need to configure a new ASA 5515-X with a 3 trunk port for vlans that become from switch, but i need turn on IPS in in-line mode, somebody has an example and limitations for this configuration type?

View 3 Replies View Related

Cisco Firewall :: Getting ASA 5505 Vlan Configuration?

Mar 14, 2013

I have IOS 8.0(4) and the base 50 User License...will this config work?  I have two networks; my home network, and my lab.  I want to split my Internet connection between them, but keep the networks separate for the most part.  Will my license allow this config since I can't do DMZ?
 
interface Ethernet0/0
switchport access vlan 3
!
interface Ethernet0/1
switchport access vlan 1
!
interface Ethernet0/2
switchport access vlan 2

[code]....

View 1 Replies View Related

Cisco Firewall :: ASA 5505 VLAN Or Trunk Configuration?

Sep 2, 2012

ASA 5505, I got a security plus license which allows multiple VLANs.I want to be able to configure the ASA to allow only RDP session (One way) to another Switch where all the VLANs are. I've attached a pic of what I want but I'm struggling.
 
I looked at documentation saying you should have inside and outside interface but I'm not sure on this scenario.I've configured inside interface on ASA e0/1 and interface VLANs but not sure what to do between ASA and Switch?

View 2 Replies View Related

Cisco Switching/Routing :: 3750 - VTP Transparent Configuration

Jan 28, 2012

We have a few stacked 3750 switches with vtp transparent configured...some plugged in a fiber from another network into our stacked switches...that network/switch has vtp server configured...once that switch connected to our stack of switches, it turned that stack switch into vtp server...causing the previous vlans configured to erase thus causing management issues with the stacked switches..

View 4 Replies View Related

Cisco Firewall :: ASA 5585 / Identity Firewall With Single Forest / Multi-Domain

Dec 28, 2011

I have a question with regard to setting up the ID firewall on the ASA 5585 in a single forest, multiple domain windows network.Currently I have a semi-operational IDF at the top level but can't find users on the lower other domains, here is the setup:I have 3 domains.

[URL]
 
Both domains have a two way parent-child trust and I can look for users in AD Users/Computer on both domains.  I initially setup the ASA to look at domain1.test.com using an LDAP aaa-server per the IDF instructions, and then proceeded to configure the ad-agent.  I installed the adagent on the domain1.test.com domain controller configured the settings on that system and had no problem adding users to the firewall and getting functionality within domain1.  I looked to see if I could see domain 2 and domain 3 users and found none.  I went ahead and added the domain2 system to the adagent on the DC and the system says that it is up, but when I search for users is not pulling them from domain2.  Instead, it shows domain1 users as domain2user1.  I also configured another adserver in the ASA to search ldap on domain 2 to no avail.The cisco documentation states the following:•Before you configure even a single domain controller machine using the adacfg dc create command, ensure that the AD Agent machine is first joined to a domain (for example, domain J) that has a trust relationship with each and every domain (for example, domain D[i]) that it will monitor for user authentications (through the domain controller machines that you will be configuring on the AD Agent machine). Single Forest, Multiple Domains—All the domains in a single forest already have an inherent two-way trust relationship with each other. Thus, the AD Agent must first be joined to one of the domains, J, in this forest, with this domain J not necessarily being identical to any of the domains D[i] corresponding to the domain controller machines. Because of the inherent trust relationship between domain J and each of the domains D[i], there is no need to explicitly configure any trust relationships.Reading that it sounds like it should just work.  I had everything properly configured before I installed the adagent, but I'm guessing that there is a chance that you can't have the adagent on the top level DC and get to communicate with the lower level domains. 

View 1 Replies View Related

Cisco Firewall :: 5585 - CSC And AIP

Oct 7, 2011

Does the 5585X supports BGP ? What if someone wants to use Antivirus + IPS feature in that . I have seen IPS modules for 5585X but looks like the antivirus module is not avaliable for 5585X

View 1 Replies View Related

Cisco Firewall :: ASA Firewall Positioning In Transparent Mode Between 6509 Core Switch And WLC

Apr 26, 2011

I do have the below setup,,
 
1. I have 6509 switch
 
2. I have 2 WLC configured in Active/Active mode connected in Trunk mode (L2 Port-Channel) connected with 6509 switch
 
3. On switch side i have configured the port as Trunk
 
4. L3 SVI for wireless users are created in 6509 switch (attached the diagram).
 
I would like to introduce a Cisco ASA 5520 firewall with AIp-SSM module so that all wirelees traffic can be inspected.
 
The issue is: Without changing any configuration in the network (switch & WLC) is it possible to introduce the firewall?

View 2 Replies View Related

Cisco Firewall :: ASA 5520 - Routed Management Interface On Transparent Firewall?

May 5, 2013

I have an asa 5520.  How would I configure my dedicated management interface to be able to route off subnet while the firewall is in transparent mode?

View 1 Replies View Related

Cisco Firewall :: ASA5512-X - ASDM In Firewall Transparent Mode

Dec 3, 2012

I would like to configure an ASA5512-X in firewall transparent mode, but I am having trouble getting ASDM to lauch when I do.
 
I have created a BVI interface with an IP address, and I hve enabled the mangement interface, but ASDM does not lauch when I enter the IP adress of the BVI I created.
 
Apprently you need to use the bridge-group command to assign an interfce to a bridge group. When I enter this command at the (config-if) prompt for Management 0/0, this command is not recognized.
 
What are the general steps for configuring the management interface to be able to launch ASDM in transparent mode?

View 1 Replies View Related

Cisco Firewall :: 5505 - Setting Transparent Firewall Ip Address?

Dec 22, 2011

Trying to set up a asa 5505 in transparent firewall mode. I cannot set the management ip address:
 
ciscoasa> enable
Password:
ciscoasa# config term

[Code].....

View 7 Replies View Related

Cisco Firewall :: ASA5540 - EAL4 Transparent Firewall Config

Mar 14, 2011

I am configuring an ASA5540 firewall for a client, only difference to usual being that it is to run in Transparent mode. I have looked through for an EAL4 transparent firewall config guide but found nothing and therefore assumed that the usual one would be used.The clients security bod has now come back and insisted MAC filtering should be used but I can find no reference of this anywhere. Does MAC filtering is required to make a transparent box EAL4 compliant and if so where I can find documentation supporting this?

View 1 Replies View Related

Cisco Firewall :: 5510 - Transparent Firewall Installation Using ASA Version 8.4(3)9

May 14, 2012

I'm trying to install an ASA 5510 transparent firewall using ASA version 8.4(3)9 but I don't understand how traffic will ever pass through my firewall if both interfaces are on the same sub net(V lan) as the host and it's default gateway? The reason I'm doing this is were installing UAG (or Direct Access) and the UAG appliance need to have public IP's but still be behind a firewall (see attached diagram).
 
Looking at the documentation (which all seems to be for 5505's running 8.2) it almost seems like i need to have the transparent firewall 'in-line' to the ISP router?, but this router services another IP address range on another v lan for other (routed) firewalls (not shown on diagram) so putting it 'in-line' is not possible. Surely this can't be the case can it? If not how is it supposed to be cabled up and configured so packets go through the firewall?

View 3 Replies View Related

Cisco Firewall :: 6509 - Is It Better To Setup Firewall As Transparent Or Routed

May 9, 2011

I am familiar with the PIX and ASA's.  We have two Cisco 6509's with a FWSM installed in both.  Our network is shown in the diagram.  We use Blue Coat Packetshapers and Barracuda Proxy appliances.  I plan on setting up HSRP on both 6509's for traffic coming from our ISP Cisco 2811's as well as use HSRP for our DMZ and internal network.  I would like to setup the firewalls for statefull failover.  We will be using PAT for our internal users and one-to-one static NAT for our DMZ. 

Is it better to setup the firewall's as transparent or routed?
 
Since the firewall is built into the switch, how do I insert the Barracuda proxies?  I can configure them as transparent or routed proxies.

View 2 Replies View Related

Cisco Firewall :: ASA 5505 Transparent Firewall With Web Sense Integration

Apr 27, 2011

I'm integrating a Cisco ASA5505 with a Websense proxy. I have a configuration setup where we have four routers which are used for Internet access. There are two VLAN's - Guest and Private. What I would like to achieve is making the use of available bandwidth by load distribution via GLBP, and filtering users web traffic. Two routers will be used for a GLBP group in one VLAN, and the other two routers will be used for GLBP in another VLAN.The users are connected to a Cisco 2960 switch and are in their respective VLAN's. I'm planning a 802.1q trunk to a Cisco ASA from the 2960 switch, carrying both VLAN's.What I would like to know is if there is a CSC module (or similar) which has Websense installed on it, and if it is possible to setup the ASA5505 in transparent mode to filter the traffic in this way? Hopefully this would allow multiple users to take advantage of the additional bandwidth, and not be restricted by using a traditional proxy setup which where all web traffic would be originating from a single MAC address.

View 1 Replies View Related

Cisco Firewall :: Setup ASA 5585 Out Of The Box?

Jan 29, 2012

Am not conversant with Firewalling. however i have need to set up CISCO ASA 5585 out of the box.

View 3 Replies View Related

Cisco Firewall :: Upgrading PIX 525 With ASA 5585-X / SSP-10

Jun 24, 2012

We are working for a client move from PIX 525 to ASA 5585-X, SSP10. This is a production environment and very critical migration. What are the gotchas which we should be aware off?

View 1 Replies View Related

Cisco Firewall :: 5585-x With IPS SSM 40 Module

Jun 2, 2013

We have installed 5585-x in active/active mode with transparent firewall. We have created two virtual sersors for vs1 and vs2 in IPS module and linked with ASA context C1(vs1), C2(vs2) and admin(vs0).

As firewall is working in transparent mode, we have bridge IP address for context C1 10.1.1.1 and for context C2 10.2.2.1.

I have added default routed for context C1 10.1.1.2 .It is in the outside of asa and SVI on switch.For the other context C2 10.2.2.2.

IP address range for the IPS module and what should be the gateway for IPS module.AS the traffic is coming from outside and going to inside interface of ASA.

View 1 Replies View Related

Cisco Firewall :: ASA 5585-X Licensing

May 6, 2012

I have registered the license purchased for the ASA 5585X appliances and have received the following listed as features.
 
> Failover : Enabled > Encryption-DES : Enabled > Encryption-3DES-AES : Enabled > Security Contexts : 20 > GTP/GPRS : Disabled > AnyConnect Premium Peers : Default > Other VPN Peers : Default > Advanced Endpoint Assessment : Disabled > AnyConnect for Mobile : Disabled > AnyConnect for Cisco VPN Phone : Disabled > Shared License : Disabled > UC Phone Proxy Sessions : Default > Total UC Proxy Sessions : Default > AnyConnect Essentials : Disabled > Botnet Traffic Filter : Disabled > Intercompany Media Engine : Disabled > 10GE I/O Plus : Disabled(code)

View 4 Replies View Related

Cisco Firewall :: ASA 5585 HA Failover?

Sep 24, 2012

I have a pair of ASA 5585 configured with 2 contexts, C1 & C2, C1 is active on ASA-1 & C2 is active on ASA-2 i did failover test, ping was initiated to host residing behind ASA-1 in context C1 i  powered of ASA-1 then both context became active on ASA-2, however during this failover.i saw 4 ping packets drop..

View 3 Replies View Related

Cisco Firewall :: ASA5510 Firewall Transparent Mode

Sep 10, 2012

i have a ASA5510 in the office, that already configured 3 context, namely, admin, user, server.in the server context, the last running config was not saved, and there was a power trip last friday night. 1 of the sub interface was affected, and i need to recreate that interface.I am getting the below error, it only allow me to do changes those pre-defined interface.how to I create extra sub interface?

View 3 Replies View Related

Cisco Firewall :: ASA 5510 Firewall Is In Transparent Mode

Apr 10, 2013

We've in our company a Cisco Asa 5510 v8.4(3), Asdm 6.4(7) and a SSM-CSC-10-K9. The firewall is in transparent mode. I get an exchange 2003 SP2 server behind. When users trying to send mailing lists with many recipients (above 300), the Exchange server didn't send these mails. I'm pretty sure that this problem come from the ASA Firewall, because when I plug my server directly on my Internet Connection, the mailing list is sent. I've search on the web, and disable "ESMTP Inspection", but it didn't work. [code]

View 4 Replies View Related

Cisco Firewall :: ASA 5585 ASDM Won't Load

Jan 28, 2013

I have a new 5585x with only basic ip information on it.  I can't get the ASDM to load from any interface.  Browser just says cannot load page.  I upgraded to 9.1 and ASDM 7.11-52. (Also did not work before I upgraded)  I can ping the managment 0 interface and can tftp data to and from it.  Also unable to telnet to the management interface. [code]

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved