Cisco Firewall :: ASA 5520 With 9.0.1 IOS - Capture To Inside Interface Not Supported
Dec 9, 2012
I recently upgraded my 5520 to 9.0.1 IOS. Today I tried to apply a capture to my inside interface referencing a simple ACL and I get this error.
ERROR: Capture doesn't support access-list <capin> containing mixed policies
I also created a capture for the outside interface with a similar ACL and it worked just fine. I can't seem to find anything on the web that gives me a clue to resolving the error above.
I have inherited an ASA 5520. In doing some auditing of the setup, I have noticed a Static Route that has the inside interface of the ASA as the Gateway IP. I am trying to understand the purpose of this route or why a route would be setup this way.
Example Static Route: Inside 10.xx.31.0 255.255.255.0 10.xx.xx.10 (10.xx.xx.10 is the inside interface of ASA)
We already have a subnet defined to inside interface and is in produciton. the default gateway is this interface ip. In that setup now I have to add one more subnet and as the first subnet is been defined in ASA indside interface, I have to assign secondary Ip to the inside interface so that new subnet users can easily reach here and go outside.
I'm trying to attach tacacs server (ACS Version 5.2) in server group on ASA 5520 (Version 8.4). When I test connection in ASDM (Version 6.4) between ASA and ACS it fails. The log message on ASA is:
%ASA-2-106016: Deny IP spoof from (10.8.27.126) to 10.8.48.10 on interface inside.
I have a asa 5520 with an outside and backup interface. I am trying to configure two static nat statements from the inside to the outside and backup interface. Here is what I have configured so far.
We currently have a setup where users connect to the inside of a firewall using the ipsec client. We are moving them to the anyconnect client but are unable to get it to work, we cannot even get a webvpn page on the inside.
When trying to connect with anyconnect the ASA reports an IKE initiator fail on the inside. and no tcp connection flag. We cannot get any response with Webvpn either I have tried using a different tcp port on webvpn but then the asa denies the traffic even though there are no rules denying.
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80 Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53 Pix(config)#access-group outbound in interface inside
I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
I've recently upgraded my old firewall from a PIX to an ASA5505 and have been trying to match up the configuration settings to no avail. I have is that I can't ping the new firewall on it's inside interface, despite having "icmp permit any inside" in the running config. Secondly, the server I have on there ("Sar") can't connect out to the internet.I've included the ASA's running config incase anybody can see if something stands out. I have a feeling it's either not letting anything onto the inside interface, or there is no nat going on. Lastly (and possibly relevant), the firewall is actually going at the end of a vlan, which is different to the firewall's inside vlan number. I don't know if this is actually the problem because the server can't connect out even if connected directly into the firewall.
I have an ASA 5520 Cisco Adaptive Security Appliance Software Version 8.4(2)8 Device Manager Version 6.4(5)206. I am trying to add a nat for outside x.x.x.77 port going inside x.x.x.22 port 80 . the wan interface is .74 with subnet of 255.255.255.248 the rule will add but traffic wont pass in.
I am setting up a pair of 5520 in A/S mode but the traffic from inside to outside seems blocked somehow.
asa01# sh run : Saved ASA Version 8.3(1) host name asa01 enable password LFJ8dTG1HExu/pWQ encrypted password 2KFQnbNIdI.2KYOU encrypted names [code]......
Base on the above configuration, I still cannot ping or HTTP.
I am trying to configure a server(192.168.5.50) in DMZ(192.168.5.0/24) to be able to communicate with a domain controller(10.5.44.220) in the inside network(10.5.44.0/24). I made some configuration using ASDM(not familiar with the CLI) but not working and it caused existing NAT not to work, for example RDP(TCP 3389) connection to 38.96.179.220
The things I am trying to achieve are
1. two way commucation between 192.168.5.50 in DMZ and 10.5.44.220 in Inside for SecureAuthPorts and SecureAuthOutbound service groups
2. NAT for 192.168.5.50 mapping 38.96.179.50 for the service groups mentioned above
I am trying to make a basic config on my 5520. The first goal is to make trafic from inside to outside.The internet address is 64.28.29.200 and the default internet gw is 64.28.20.193What am I missing since I can not get trafic from inside to the internet? [code]
I have ASA 5520. I cannot ping the host(192.168.1.20) which is inside firewall from outside hosts. Inside host (192.168.1.20) is translated into (198.24.210.226) using static NAT.From outside host, I used "PING 198.24.210.226". Is it because I used dynamic PAT for inside hosts?
I am new in ASA, I have the DMZ (10.1.1.0/24) configured on ASA 5520 and I achieve the reach Internet from DMZ (10.1.1.0/24), but now need reach DMZ from inside (172.16.12.0/24) and inside (172.16.12.0/24) from DMZ (10.1.1.0/24), in other words round trip.
I am trying to upgrade a Cisco ASA over an IPSEC VPN tunnel. My FTP server is on the remote side of the VPN tunnel but I am initiating connections from the inside interface of the firewall. I am currently managing the Firewall over the VPN via it's inside interface (using the management-access inside) command. When I try and update via FTP, the connection is going straight out the outside interface (and not across the VPN tunnel) I have tried upgrading via TFTP but it keeps stopping randomly with (unspecified error) I normally upgrade via FTP though but it's not working in this instance. Essentially what I am asking, is is there an equivalent command for FTP that there is for TFTP: tftp-server interface ip anyconnect I need the connections to originate from the inside interface so they traverse the VPN. I am running 7.2.3?
I have a handheld device that will be used for inventory outside of our office. It has 3g capabilities. Is there anyway I can permit traffic from this device from the outside world coming into my network? I need to open a couple of ports so it can hit the server. But I have no intention to open these ports up to the entire world. I use an ASA 5520 with a managed router from our provider. I looked around on the Cisco site and the only information I found was for permitting and denying traffic from devices that are within the network.
I have a new ASA 5505 and all is working fine, I can CLI and ASDM into it, but just can't ping the inside interface, do I need to enable a feature to make this work somehow?
I am connecting the inside interface to an upstream switch and therefore will need to assign a static IP address to the inside address as I did below:
#sho int ip brief Vlan1 123.123.123.123 YES manual up up
I will also use this to manage the ASA. I am having a problem with the network configuration of the inside interface as I can't ping the gateway and/or the in IP of the inside interface.Do I need to add any routes?
I have a Cisco 5512 x Firewall connected with Cisco Layer 3 switch 3750.I have two different WAN connections, one for Data and one for voice. Cisco Layer 3 switch is configured with 2 different VLAN's one for data & other is Voice Vlan. Switch is providing DHCP to computers and IP phones. Voice Pool 192.168.10.0/24 Vlan10 and Data pool 192.168.20.0/24 Vlan20.I need to route my data & voice traffic separately. Cisco ASA is connected with two different ISP's. So, how can I do this configuration so that Voice and Data traffic will route separately.
I ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
the inside interface on our primary ASA seemed to "hang". It dropped all the packets it received. Because the interface didnt go down, failover didn't happen. Device's info;
-Cisco Adaptive Security Appliance Software Version 8.2(3) -Device Manager Version 6.3(3) -Hardware: ASA5550, 4096 MB RAM, CPU Pentium 4 3000 MHz -Internal ATA Compact Flash, 256MB -BIOS Flash Firmware Hub @ 0xffe00000, 1024KB
I attached a capture picture shows that traffic didnt go to the roof when the issue happened. Why the interface would "freeze" randomly?
I build a Config with a DMZ,INSIDE and OUTSIDE Interface. My Plan is to use the IP-Address of the OUTSIDE Interface with PORT to setup a HTTP Server In the DMZ
But my Config doesn't work. And I have no Plan why .....
The Inside Interface have to work normal. The Traffic to the Internet is TRiggert from Inside with Dynamic PAT
ciscoasa(config)# exit ciscoasa# show run : Saved : ASA Version 8.4(1)
I have an ASA 5505 that I'm trying to set up a guest network on. I've configured an interface as a trunk and allowed the 2 vlans but I'm not getting any layer 3 to it. The switch connected to it is a 3560 and port is configured as a trunk with the same vlans.
I can't ping the ASA inside interface but I see its MAC address in the swtich's table.
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
I did this on the PIX and it worked like a charm, but I am having some difficulty translating the configuration to an ASA.
In the PIX I performed NAT on outside traffic to a specific inside host (web server) to map to the inside interface so that return traffic would go to the same firewall the traffic came in through, The reason for this configuration was because the gateway of last resort was a different firewall and not the firewall the traffic came in through.
Now to further give you some history, the gateway of last resort is an ASA running 9.1 (Now), prior to that it was a PIX with v8.0(4), traffic to the aforementioned web server came in through the gateway of last resort), which at the time was the PIX.
However, for some reason after swapping the PIX for an ASA (same rules, updated NAT rules for 9.1) access to the same web server is slow. Not sure why, but it’s the case. To alleviate the slowness we experienced, and until I can figure out why this occurs on the ASA, I placed a PIX on the network that only listens for traffic for the web server in question. On this PIX I map to the inside interface so that traffic flow works and external clients can access the web server with no issues.
So two questions, one I would like to use the configuration I have for the web server on the PIX on the ASA to see if that setup on the ASA works better, but having difficulty translating the rules to the ASA.
Second question, (Slow access with ASA to a web server, but fast with PIX to the same web server)?
P.S. Addresses in attached picture config are not real, but I know what they translate to.
we have a server that has an outside IP and an inside IP. It's inside ip is 192.168.222.30/24 and it's outside IP is 199.204.50.2/29. The connection to this server from the outside is perfectly fine, but access from inside users to the NAT'd IP which is 199.204.50.2/29 is having issues, however, access to the inside IP works fine (this part makes sense)Will It be a must to set the inside DNS A record to the inside IP and not the outside IP, or can users on the inside interface access the NAT'd IP which is assigned to the server
LAN(192.168.222.0/24)<=====>InsideASAOutside<=====>(Server with NAT IP 192.168.222.30/24, it's also physicall assigned to this server).This is an ASA 5510 with 8.4.
I have a PIX 515e running version 7.2(4).I have 2 interfaces - DMZ3 (sec lvl 50) and LAB (sec lvl 100) behind the pix. There is also the OUTSIDE interface (sec lvl 0) which connects to the internet.In DMZ3 I have a webserver - x.x.124.217/24 (host is NATed via static command to public IP)In LAB I have a server - x.x.1.203/24 (entire range is NATed via NAT/Global statements to public IP)The server in LAB needs to access a webserver in DMZ3. From the internet both of these hosts have public addresses that are NATed into the inside addresses. I can reach the webserver from the internet, but not from the LAB interface.I think I have to add a static command so that the LAB host can access the DMZ3 host without accessing the internet.
I need to configure a Cisco ASA5510.Connencted the a single interface I have a switch. To this switch (same VLAN) there are connected:
1. The Subnet of the main office (192.168.1.253)
2. A router (IP 192.168.1.254) that routes the traffic to a remote location (Subnet 192.168.8.0/24)
I have so allowed any traffic incoming to the inside interface as follows:access-list inside_access_in extended permit ip any any and I have permitted traffic intra interface as follows: same-security-traffic permit intra-interface. [code]Unfortunately I cannot RDP into that server. When I simulate the connection via Packet tracer, it tells me that the implicit deny on the bottom of the connections from "inside" (firewall) does not allow the connection. It sounds to me like that "same-security-traffic permit intra-interface" does work only if there are 2 interfaces and not a single one.Unfortunately I cannot just unplug the cable and connect it into another port as the ip is on the same subnet and I cannot configure the other end router.
I have ASA5505 configured with internal network as 192.168.15.0 and default gateway 192.168.15.1 From the inside network, i'm able to access internet and able to ping all website (enabled ping). and all internel network devices can ping each other. Except i cannot ping my gateway (ASA5505) 192.168.15.1. I'm continously seeing this message on the log, when i tried to ping.. How to fix this?
Denied ICMP type=8, code=0 from 192.168.15.xxx on interface inside
replace xxx with my network devices that try to ping the gateway..I dont want outsiders ping my gateway, i need ping for inside internal network only.
