Cisco Firewall :: ASA 5550 - Cannot Ping SITE 1 PIX From Internal IP
Oct 15, 2012
We have two networks HQ and Site1 and for some reason we can’t ping the inside IP for Site1 PIX device. We have site-site-VPN set up between the two and everything works fine except we can’t ping the Site1 PIX from internal IP. However, I can ASDM/SSH in from HQ to the external IP of the Site1 PIX.
HQ is using an ASA 5550 (172.1.0.1) PC from HQ (172.1.64.x) Site1 is using a PIX-515E (172.2.0.1) PC from Site1 (172.2.64.x)
Ping from HQ PC to Site1 PC (172.1.64.x to 172.2.64.x) works fine
Ping from Site1 PC to HQ PC (172.2.64.x to 172.1.64.x) works fine
[code]...
ASDM/SSH from any HQ PC to Site1 PIX internal IP (172.1.64.x to 172.2.0.1) doesn’t work
ASDM/SSH from any HQ PC to Site1 PIX external IP (172.1.64.x to Site1 external IP) works fine
Everything was working fine until we recently changed the outside IP address for Site1 because we switch to a different ISP. Nothing changed on the HQ ASA or Site1 PIX other than the outside IP address on Site1 PIX. I did rebuild the site-to-site VPN tunnel between Site1 and HQ.
View 5 Replies
ADVERTISEMENT
May 30, 2012
I have the following VPN site-2-site configuration.The trouble I'm having is host 172.168.88.3 in site A is not able to ping 172.168.200.3 in site B and visa versa. Think I have added the static routes and ACLs correctly on the 3560 switches (acting as gateways) and both PIX's to access the internal networks. Host 172.168.9.3 can ping 172.168.200.3 fine.
View 3 Replies
View Related
Jun 8, 2011
I am trying think of a better way to provide redundancy on some internally protected networks. We maintain our own WAN/backbone between our primary site and backup site. Is it possible to have two Cisco ASA 5550s in setup for failover at completely different sites as long the networks connected are available?
View 3 Replies
View Related
Mar 28, 2012
I just setup my home network with Pix 515 acting as my router/firewall but I can't seem to ping my internal PC from my ASA. I can access the internet and ping my Pix 515 inside interface from my pc but I can't ping my pc from my Pix 515. I can also renew/release IP's from my PC. I also did a packet tracer and it says that it was dropped due to an access list but I have one in place. Also my switch has the default config. Below is my config
Internet <----> Comcast modem <-----> Pix 515 <-------> Cisco switch <-----> PC
MYFIREWALL# sh run
: Saved
[Code].....
View 4 Replies
View Related
Jan 15, 2012
Cisco ASA 5505 Cannot Ping Secondary Internal Network.
View 9 Replies
View Related
Sep 12, 2011
I have configure Cisco 5505 as layer 2 firewall mode. I have vendor machine connected to Cisco ASA 5505 on port 2 as VLAN2 inside then VLAN1 outside connected to my internal network on layer 2 cisco 2960 switch. This machine needs access only to LOGMEIN then block all internal/internet traffic.
vendor machine on vlan 2 inside >> Cisco ASA 5505 vlan1 outside >> layer2 switch >> internal LAN >> Cisco 5520 main FW >>> INTERNET
View 1 Replies
View Related
Mar 17, 2013
I have created a VPN connection for ASA 5512-X by using the wizards and nothing seems to be wrong on the wizards's config.I am able to connect to the network by using the VPN but unable to ping internal network.Below is my config for your reference:
Result of the command: "sh run"
: Saved
:
ASA Version 8.6(1)2
!
hostname FAA-ASA-1
enable password crzcsirI44h2BHoz encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code].....
View 6 Replies
View Related
Oct 11, 2011
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies
View Related
Jun 11, 2013
We recently purchased an SRP527W router because of its capability to configure site-site VPN tunnels. The configuration of IKE and IPSEC is working and the tunnel comes up but the problem is that the router is passing our internal IP addresses through the tunnel. The remote end we are connecting to requires us to hide all traffic behind one IP address which would ideally be our external static IP address from our ISP.
View 1 Replies
View Related
Mar 3, 2011
I have 3 ASA 5505 Firewall, I am creating Site 2 Site Full mesh tunnel with each firewall, the problem i am facing is two of the firewalls internal schema are same, Like Site 1 has an Internal Schema: 192.168.0.0, Site 2 has an Internal Schema 192.168.0.0, Site has an Internal Schema 10.10.10.0
For that i have to create a policy static nat and access list??
I configurred a access-list like below,
access-list vpn_ih_site3_site1 permit ip 10.10.10.0 255.255.255.0 192.168.0.0 255.255.255.0access-list vpn_ih_site3_site2 permit ip 10.10.10.0 255.255.255.0 192.168.0.0 255.255.255.0
View 10 Replies
View Related
Jul 12, 2012
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies
View Related
Apr 3, 2013
I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
crypto isakmp policy 1
encr 3des
hash md5
[Code].....
View 9 Replies
View Related
Oct 28, 2012
I have a very basic lab site to site vpn setup where I have a ASA 5505 running v7.2(4) on one side and a cisco 2811 on the other side.
What's my issue?
I can't seem to ping from cisco router to the 'inside' network of ASA (see config below) and can't seem to ping from ASA packets leaving the 'inside' interface to cisco router even w/ an ICMP ACL permit outside in. However I'm able to ping within ASA inside network & ping cisco 2811 side w/ packets leaving ASA 'outside' interface just fine.
example:
-------
ciscoasa# ping inside 10.20.20.1 (to cisco loopback1 from ASA inside)
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.20.20.1, timeout is 2 seconds:
[Code].....
View 6 Replies
View Related
Oct 1, 2012
I just get it that I can make a VPN Site-to-Site IPSec. But if I try to send a ping from one PC (network 1) to the other PC (network 2) it failed.
PC (Network 1) <ASA5505> Switch <ASA5510> PC (Network 2)
between the two ASA I have a funkctional VPN IPSec tunnel, but I can`t get access from one to theother network.
That are the access-list on the ASA5505:
asa5505#
access-list cached ACL log flows: total 0, denied 0 (deny-flow-max 4096)
alert-interval 300
access-list Inside_ICMP; 4 elements
[Code].....
View 19 Replies
View Related
Jan 18, 2013
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies
View Related
Feb 20, 2013
I have two Cisco ASA routers and I have a site to site vpn set up between the two. The VPN link works but Site A can't ping anything on Site B. Site B can ping Site A. Site B can ping other pcs on it's own network. Site A has been in place for a while and has other site to site VPNs that work fine, so I think the problem is with Site B. Here is the config for Site B:
Result of the command: "show running-config"
: Saved
:
ASA Version 8.4(4)1
!
hostname SaskASA
enable password POgOWyKyb0jgJ1Hm encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
View 6 Replies
View Related
Mar 5, 2012
I am unable to ping any device on the internal lan from the opposite side of the tunnel. However, the tunnel connects successfully. I have the firewall disabled on both routers. Site A is using 192.168.3.1 and Site B is using 192.168.4.1. Any thoughts on why I cant ping one router from the other?
View 4 Replies
View Related
Mar 27, 2012
I've 3 Cisco 800 series routers and I needed to configure site-to-site vpn tunnel from branch2 to the main office(branch 1 VPN was already configured and working). I've managed to get the tunnel up and everything seemed OK as sh cry isa sa,sh cry session and sh cry ipsec sa didn't seem to have any problems.
Although the tunnel is up, I cannot ping PC-s on either side of the vpn tunnel.
View 8 Replies
View Related
Aug 15, 2012
we have the following setup for our network :
UserNetwork - ASA5550 - WAN Router 2911 - ISP Netowrk - Branch Routers 877s / 1941s
Since last week we started noticing this problem that the branch users started to complain of slow application response.. After verifying it with the ISP and middle network we noticed that if i ping from my machine (ie usernetwork) to the WAN Router interface (facing the ASA) , i get time outs.. which is strange cause this is directly connected to it via ethernet cable.
View 5 Replies
View Related
Jan 25, 2013
Site is not opening in any of my systems in the local network. but if i change ip to a real ip or if i use some other internet source like netsetter then it gets opened.
View 1 Replies
View Related
Feb 22, 2012
I'm running into a strange problem and cant seem to figure it out. I have an asa running 8.2(1). I have an ipsec vpn setup and working great. I can ping hosts on the inside of the network and everything seems to be fine. However there is one single ip address that i know for a fact is live, but i cannot ping through the vpn. If i ping the address from the asa i get a reply, if i ping the address from inside the network i get a reply, but if i ping when connected through the vpn no reply.
View 4 Replies
View Related
Nov 11, 2012
I have the connection working with my ASA 5505 but cannot ping the internal network. (Note external interface is getting the IP via DHCP)
View 4 Replies
View Related
Dec 6, 2012
I'm having an issue where internal hosts cannot access the internet but I am able to ping external hosts when I console into the router. The router is a 2800 series. [code]
View 3 Replies
View Related
Feb 6, 2011
I'm new to this cisco 5505 and I want to carry out a task as simple as a remote access VPN, in my case I did the wizard, with time on my test, I could connect to the VPN, but I can not ping any device internal network. [code]
View 6 Replies
View Related
Mar 3, 2011
i two 5550 firewall set up for redundance purpose . in failover we define two different ip add one for primary and one for secondary .interface Ethernet0/0 nameif outside security-level 0 ip address xxxx.0.0.0.1 255.255.255.0 standby xxxx.0.0.2!interface Ethernet1/0 nameif inside security-level 100 ip address 10.0.0.12 255.255.255.0 standby 10.0.0.11.default gateway for host will be 10.0.0.12 (primary fw address) however in case of failover , the secondary fw will be up with ip address that was assigned for primary .in this case the secondary ip add 10.0.0.11 is actually nerver used? similarly do i need to have two public ip address for outside (one for primary and one for secondary ) ? or in case if primary fails the secondary comes onlie and take the ip of primary fw . hence i only need to purchase just one ip address.
View 6 Replies
View Related
Feb 22, 2013
I have cisco 5550 Firewall, one messages appear in syslog server from Firewall, (warning) i want to stop this message from appearing syslog traps.
View 2 Replies
View Related
Apr 17, 2011
I am having two ASA 5550 firewall running in active/standby mode. With in last two months our secondary firewall got down automatically 3 times. Firewall is running with IOS version 7.1.2. how to proceed further troubleshooting because there are not any logs on firewall.
View 3 Replies
View Related
Dec 3, 2011
I've got a 2621 configured as my main gateway to the internet - right now it's obtaining a DHCP ip from a the ISP's proprietary router set to bridged mode.
As of now, I'm unable to ping the internal interface of the router. I can ping external IP's only, even though I have DNS servers listed, i am unable to resolve host names. I'm running a few servers to which people are able to connect to my web server, among other services. I even have a crypto map setup to another 2621 across the country and can ping all internal ips on the other end... I JUST CANNOT PING THE INTERNAL INTERFACE of the router!!
I've noticed that when I ping the router during it's boot process (using linux un-interupted) I get a response in a very short window, then dies again. I'll post my config below:
[code]....
View 9 Replies
View Related
May 30, 2013
I would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
1) what is the different to build site to site VPN between router and firewall ?
2) which is the best choice if using in site to site VPN connection ?
View 9 Replies
View Related
Jul 28, 2011
I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.
View 5 Replies
View Related
Aug 13, 2012
Got an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.
Currently the rules are as follows
Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny
[code].....
It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.
View 2 Replies
View Related
Mar 9, 2011
I am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .
i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).
View 6 Replies
View Related
Oct 10, 2012
I have a ASA 5510 at our corporate HQ that has one site to site VPN. I need to add 6 additional site to site VPN's to this ASA for our remote branches. How can I add them without affecting the existing site to site VPN? The 6 site to site VPN's will all have the same settings however these settings are different from the existing site to site that I already have set up. How can I set it up so the 6 additional VPN's use their own crypto map and all use the same settings?
View 1 Replies
View Related
