Cisco VPN :: One Router On ASA 5505 Site To Site VPN Can't Ping Other
Feb 20, 2013
I have two Cisco ASA routers and I have a site to site vpn set up between the two. The VPN link works but Site A can't ping anything on Site B. Site B can ping Site A. Site B can ping other pcs on it's own network. Site A has been in place for a while and has other site to site VPNs that work fine, so I think the problem is with Site B. Here is the config for Site B:
Result of the command: "show running-config"
: Saved
:
ASA Version 8.4(4)1
!
hostname SaskASA
enable password POgOWyKyb0jgJ1Hm encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
View 6 Replies
ADVERTISEMENT
Oct 11, 2011
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies
View Related
Oct 28, 2012
I have a very basic lab site to site vpn setup where I have a ASA 5505 running v7.2(4) on one side and a cisco 2811 on the other side.
What's my issue?
I can't seem to ping from cisco router to the 'inside' network of ASA (see config below) and can't seem to ping from ASA packets leaving the 'inside' interface to cisco router even w/ an ICMP ACL permit outside in. However I'm able to ping within ASA inside network & ping cisco 2811 side w/ packets leaving ASA 'outside' interface just fine.
example:
-------
ciscoasa# ping inside 10.20.20.1 (to cisco loopback1 from ASA inside)
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.20.20.1, timeout is 2 seconds:
[Code].....
View 6 Replies
View Related
Feb 7, 2011
I have ASA 5505, i configured site to site vpn between central site and remote site and is working. Now the problem is we use remote site for troubleshooting purpose, so we need to create a tunnel from remote site to central site. I need to configure such a way that remote site can craete a tunnel to central site, but central site not able to create a tunnel, it just respond to remote site.
View 3 Replies
View Related
Mar 6, 2011
i have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies
View Related
May 30, 2013
I would like to know both Cisco 2901 or 2921 router and Cisco 5505 ASA can build site to site VPN.
1) what is the different to build site to site VPN between router and firewall ?
2) which is the best choice if using in site to site VPN connection ?
View 9 Replies
View Related
Mar 31, 2011
Just now my boss asked me to prepare to set up site-to-site VPN on Cisco 881 Integrated Services router to ASA 5505 router which is now running at the HQ side. I am now learning pdf file from Cisco which mention how to setup site-to-site VPN between Cisco 1812 IOS router and ASA 5505 router by using ASDM V6.1 and SDM V2.5. Can't find the paper for that Cisco 881 device.
View 4 Replies
View Related
Nov 25, 2012
I have an offsite employee at an apartment complex where she uses the leasing offices internet connection. I have an ASA 5505 but I don't know how to make this work behind the leasing offices router and other network equipment. Is there any way to have her connect back to our corporate network using site to site vpn without touching the leasing office devices? She needs VoIP and corporate server access.
View 3 Replies
View Related
Nov 21, 2011
Hoping that someboy can see the error of my ways. It seems very like the problem that i read here: URL
We have a cisco 800 in a remote site which we wanted to use for a site to site vpn. Went through the steps on the ASA 5505 and the 800 and have got to the stage were the tunnel is up and connected. Getting traffic through it is another matter. Remote network is 172.20.224.0/20 and the server network behind the ASA is 192.168.168.0/24. The tunnel does intiate when you send traffic from 172 ......to 192....... Both the ASA and 800 report the tunnel is up. If i look at the stats using ccp on the 800 i can see the encapsulation packets graph shooting up but nothing cominbg back. I did packet captures on the 5505 and could not see anything coming from the tunnel so i dont belive its making it to the ASA. Here is the config from the 800:
Building configuration...
Current configuration : 6488 bytes
!
version 12.4
no service pad
service timestamps debug uptime
service timestamps log uptime
[Code]....
View 9 Replies
View Related
Jul 12, 2012
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies
View Related
Apr 3, 2013
I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
crypto isakmp policy 1
encr 3des
hash md5
[Code].....
View 9 Replies
View Related
May 30, 2012
I have the following VPN site-2-site configuration.The trouble I'm having is host 172.168.88.3 in site A is not able to ping 172.168.200.3 in site B and visa versa. Think I have added the static routes and ACLs correctly on the 3560 switches (acting as gateways) and both PIX's to access the internal networks. Host 172.168.9.3 can ping 172.168.200.3 fine.
View 3 Replies
View Related
Oct 1, 2012
I just get it that I can make a VPN Site-to-Site IPSec. But if I try to send a ping from one PC (network 1) to the other PC (network 2) it failed.
PC (Network 1) <ASA5505> Switch <ASA5510> PC (Network 2)
between the two ASA I have a funkctional VPN IPSec tunnel, but I can`t get access from one to theother network.
That are the access-list on the ASA5505:
asa5505#
access-list cached ACL log flows: total 0, denied 0 (deny-flow-max 4096)
alert-interval 300
access-list Inside_ICMP; 4 elements
[Code].....
View 19 Replies
View Related
Mar 5, 2012
I am unable to ping any device on the internal lan from the opposite side of the tunnel. However, the tunnel connects successfully. I have the firewall disabled on both routers. Site A is using 192.168.3.1 and Site B is using 192.168.4.1. Any thoughts on why I cant ping one router from the other?
View 4 Replies
View Related
Nov 27, 2011
We've just deployed a site-to-site VPN using a 5505 ASA on the client's site and a checkpoint Nokia FW on our site. Everything seems to be fine except that the user's connections to their file shares seem to be intermittently dropping. One minute the connection to the shares is there, next thing it's lost. There is no logic to it because no two users are experiencing issues at the same time, as a matter of fact even on the same PC where a user has access to 3 shares on 3 different servers, one could be showing as connected whereas the other two be dropping. [code]
As you can see the Duplex and Speed are set to auto, I've rectified this since then and I'm keeping a close eye on the output errors, and collisions. However, I'm afraid that this did not rectify the issue and the users are still experiencing intermittent connection dropping to their file shares over the VPN!
View 1 Replies
View Related
Jul 28, 2011
I have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.
View 5 Replies
View Related
Aug 13, 2012
Got an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.
Currently the rules are as follows
Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny
[code].....
It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.
View 2 Replies
View Related
Aug 14, 2012
Got an ASA5505 connected to another endpoint running IPsec and being NAT'd at each end to a 10.0.0.0/24 network. I can pass other types of traffic through the ASA 5505 but not RTP traffic. The moment it is NAT'd and hits the firewall rules it gets denied by the default deny at the bottom of the list.
Currently the rules are as follows
Incoming External
allow ip any any
allow tcp any any
allow udp any any
default deny
[code]....
It wont allow us to setup a voip call...however when the same call manager sets up a voip call NOT using this ipsec tunnel it works just fine.
View 3 Replies
View Related
Jan 16, 2013
We have a client that has a Cisco 1801W Firewall that is setup as a site to site VPN terminating to a Cisco ASA 5505. The tunnel is up and established, I can ping from both sides of the tunnel.
The problem is the clients behind the Cisco ASA (192.168.2.x) cannot reach certain ports behind the Router (192.168.1.x). The main thing we're trying to do is browse via UNC path (ex: \192.168.1.120 from a 192.168.2.x machine).
I got 3389 working after I changed the - ip nat inside source static tcp 192.168.1.120 3389 y.y.x.x 3389 route-map DM_RMAP_1 extendable Modified the command to include the public IP instead of interface FastEthernet0
I believe it has something to do with the way NAT and route-maps are setup currently but I'm not familar enough with them to make the changes. I worked with Cisco to ensure the VPN tunnel was fine and it's something security related on the Router.
Here is the configuration (removed a few lines not necessary. y.y.x.x = WAN IP of Router x.x.y.y = WAN IP of ASA).
Building configuration...
Current configuration : 23648 bytes
!
version 12.4
no service pad
[Code].....
View 1 Replies
View Related
Aug 8, 2011
im drawing a blank trying to setup a site to site connection with a 5505 ASA using ipsec and isakmp.i have the pre shared key as well as the external address of the other end of the tunnel but do not remember what the commands are to setup the crypto map and isakmp.
View 7 Replies
View Related
Apr 30, 2012
Need to know the step by step procedure for monitoring site-to-site VPN tunnel (up/down) using SNMP on Cisco ASA 5505.
View 1 Replies
View Related
Dec 12, 2012
I have tried Cisco presales but got bounced - go Cisco !So, i have a small customer who requires a single device which will provide .....
1/ Leased Line connection @ 10mb
2/ ADSL failover onbox (so configurable from CLI, unlike the 860’s which I see only have one ‘active’ wan port)
3/ IOS based
4/ integrated 4 ports (min) switch
5/ site to site VPN
6/ up to 10 x SSLVPN remote users
I did pitch in with ASA5505 with external ADSL router but he is “space-constrained”.It worries me when Cisco doc's say only one WAN port is 'active' - since it doesn't say the second port automatically comes up if the first goes down so I can't take a gamble on that being the case.
View 3 Replies
View Related
Dec 19, 2012
I've set up a standard site-to-site VPN between 2 ASA 5505s and the VPN is working fine for traffic between these ASAs and computers which are in the same LANs.but when I'm trying to connect to computers which are in another VLAN I have a problem.
View 1 Replies
View Related
Nov 20, 2012
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
All these remote networks are at the Main Site Clavister Firewall.
View 1 Replies
View Related
Sep 6, 2011
I have an ASA5505 running which is on a static IP. I have just got an SRP527W for a remote worker and want to create a site-to-site VPN into the ASA. I have a number of other router of non-cisco brand which just all dial-in and connect no problem.
On other routers I have been abloe to specify the DDNS hostname in the VPN setup so that the ASA can identify it. I'm not sure how I setup the SRP527 to connect to the ASA.
View 3 Replies
View Related
Mar 13, 2011
I have 2 ASA 5505 Firewall, I Configured Site 2 Site VPN no both the fitrewall, as i have a dual ISP, i am able to create the tunnel with primary but once my primary is down i am not able to create the tunnel with back up ISP. During the troobleshoothing by typing Show isakmp sa and Show ipsec sa, i can see my tunnel is up, but not able to decap the packets.
As it will look like
#pkts encaps: 15, #pkts encrypt: 15, #pkts digest: 15 #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 15, #pkts comp failed: 0, #pkts decomp failed: 0 #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0 #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0 #send errors: 0, #recv errors: 0
View 4 Replies
View Related
Aug 15, 2012
I wanted to know the maximum VPN client sessions (using the Cisco VPN client) and Site-to-Site VPN tunnels that I can connect to my ASA 5505 simultaneously.
In other words, if I have x VPN clients and y Site-to-Site tunnels, at any time, does x + y have to be <= 10 (Total VPN Peers)? If yes, can I upgrade to the security plus license to increase the Total VPN Peers to 25?
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
[Code]...
View 3 Replies
View Related
May 21, 2011
Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24
View 5 Replies
View Related
Mar 27, 2012
I've 3 Cisco 800 series routers and I needed to configure site-to-site vpn tunnel from branch2 to the main office(branch 1 VPN was already configured and working). I've managed to get the tunnel up and everything seemed OK as sh cry isa sa,sh cry session and sh cry ipsec sa didn't seem to have any problems.
Although the tunnel is up, I cannot ping PC-s on either side of the vpn tunnel.
View 8 Replies
View Related
Dec 27, 2012
Last week, I was able to establish a site-to-site VPN tunnel between an ASA 5505 and Cisco C881 router just fine. The tunnel was up and and running for a number of days but today the tunnel is no longer up. I was wondering how, if there are any commands to re-establish or re-initiate the tunnel.
View 3 Replies
View Related
Nov 13, 2012
I have a 5505 asa code version 8.3(2). Trying to set up a site to site tunnel with someone and he is asking if I can use ike v2. How do I go about setting up the tunnel to use ikev2? Is ikev2 an option with site to site tunnels?
View 5 Replies
View Related
Oct 17, 2012
ASA is configured with the VPN site to site using the wizard, created the Public IP of contivity, local and remote LAN . I attached the configuration. In contivity have the following settings: Not able to communicate both subnets.Do I need to configure IP subnets and published in the contivity as was done in the ASA?
View 3 Replies
View Related
Apr 18, 2013
I am not very experienced with Cisco networking.
Here is the situation.
Site A - headquarters 192.168.1.x
Site B - remote office 192.168.20.x
Site C - remote office 192.168.30.x
Site A - ASA 5510
Site B - ASA 5505
Site C - ASA 5505
Site-to-site VPN is established and works between A and B, A and C. Users would like to establish a tunnel between B and C to work on a common project and the data is on Site B.
I tried configuring the S2S VPN with pre-shared keys on both firewalls at sites B and C but in the end it is not established (I cannot ping either side). I used the Wizard interface multiple times and one time the CLI. I generally followed the settings chosen between the headquarter and the individual remote sites and tried to replicate them. Obviously I have made a mistake somewhere.
Could there be any limitation on the ASA 5505 in terms of licensing and the number of S2S tunnels?
View 7 Replies
View Related
