Is it possible somehow to define externally administred DNS namese in ASA 8.4 in within object groups?i know that we can use name XXX, but some idea popped up using this kind of configuration.
View 3 RepliesI have an ASA5510 where I have defined object-groups and then associated them with a specific ACL. Our ISP is pulling their point of presence from where I live and I am force to move to a new ISP. I am in the process of setting up another interface for the ASA5510 to connect to the new ISP.
My questions is can I create a new ACL lets call it new_access_in and use it with the same object groups that I have already defined? I know that I can only have one ACL bound to an interface, and will bind this new ACL to the new interface I am setting up, but I wasn't sure if I could use the same object groups and connect them to a different ACL. I really don't want to have to create new object groups if I don't have to.
I have an ASA 5510 and have just started using object-groups which are super handy in theory, but not working in reality. I have a service object-group with a mix of tcp, icmp, and udp ports. Let's call it Sample_Port_Group. I'm trying to apply it to my dmz_access_in ACL. Here's the line giving me problems:
access-list dmz_access_in extended permit object-group Sample_Port_Group 192.168.1.1 any
The asa throws up an error between 192.168.1.1 and any. When I put up a ? after Sample_Port_Group, it gives me the option of putting in an IP address, any, etc. When I put in a ? after 192.168.1.1, it only gives me the option of putting in an IP address.URL
Those posts gave me the impression my line was possible, especially the "access-list outsideacl extended permit object-group myaclog interface inside any" line, which is at the end of the 2nd article linked.
We are facing the problem in ASDM 5.x creates duplicate network object groups in the configuration when PIX with software 7.0.7 is used.
Audit report its showing below commands :
asdm group SALES_ref dmz2 reference SALES object-group network SALES_ref network-object 172.20.7.8 network-object 172.20.10.3 network-object 172.20.11.2
no access-list dmz2_access_in extended permit tcp object-group Network_10.10.1.0 object-group SALES object-group SALES_Ports access-list dmz2_access_in line 200 extended permit tcp object-group Network_10.10.1.0 object-group SALES_ref object-group SALES_Ports
i was created SALES object group 2 month back after that ASDM Automatically created the duplicate object with SALES_ref name and changed the old ACL.
After reading the post titled "ASA 5520 nat access-list query for internet access" I realized the object-group command could and should be used to make a more efficient and cleaner configuration. My current environment is very small and straight forward consisting of one FTP server in the DMZ. Though the guide: [URL] is straight forward, my inexperience hinders me from seeing how to use the commands effectively. A summary of the configuration is at the bottom of this post
Question: How can I clean up my current configuration? I have two references to the same server, dmz-rdp and dmz-ftp, created for port forwarding ports 3389 and ftp through the outside interface. I can combine them into one object statement, right? for each port I want to forward through the outside interface?
object network dmz-rdp
host 10.10.10.4
nat (DMZ,outside) static interface service tcp 3389 3389
[Code]....
Just planning my move to 8.4(2) and I'm looking for some input. In the past, I have a text file with name commands for every host on my network that I know about. I would then deploy this list to all ASAs so that I could create ACLs on any firewall using a name, which would correlate to the same IP on any firewall.Now, the names from the name command no longer work as a host entry in ACLs, therefore I'm required to switch all of my active name command entries over to objects.My question is, have any of you found an easy way to change all name commands to objects? Since the name command doesn't specify the mask of the entry, I think this may not be possible without manually updating thousands of records. I know that once I migrate, there will be some objects auto-created, but those will only be host and or networks which have NATs associated with them.
View 7 Replies View RelatedAny way of doing named objects or object groups for ACLs on the ASRs? (1000 series in this case.) I'm setting up an ASR with a zone-based firewall and writing out all the addresses, ports and protocols for the ACLs associated with the various zones is creating huge, unwieldy ACLs in the config.
View 11 Replies View RelatedI have started to use ip extended access-lists on several 3750X-switches to filter inbound and outbond traffic on the VLANs. But it seems that the use of object-groups is not supported, is this correct? Is it really no way to group different ip-addresses into groups and then use these groups in the access-lists?
I am running sw version 15.0(1)SE2.
Does the ASA treat an object-group with a network-object containing a range of IP addresses as a netmask? For example, I can apply this configuration without the ASA throwing any errors though the configuration calls for a 'net mask':
object-group network test
network-object 192.168.0.0 192.168.63.255
?
network-object-group mode commands/options:
A.B.C.D Enter an IPv4 network mask
sh run ob id test
object-group network test
network-object 192.168.0.0 192.168.63.255
I found that in the documentation it requires a netmask as oppose to a range. Is this a bug in the code? I am running code version 8.0(5)23 on a 5520. If this is not a bug how does the ASA treat this type of configuration when applied to an access list? When I ran a quick packet trace and denied access from that range it looks like the ASA doesn't read that configuration properly.
I created some User Defined Groups in LMS 4.1, now I want to apply certain fault notification groups to Event Sets.
Unfortunately the Groups I configured are not in the Group Selector of the Fault Notification Group: Admin > Network > Notification and Action Settings > Fault Notification Group
We have an ASA5505 that we need to enable hairpinning on.... In the old firmware versions, we used to be able to configure a public to private static mapping along with hairpinning by using
static (inside,outside) outside_ip inside_ip netmask 255.255.255.255
static (inside,inside) outside_ip inside_ip netmask 255.255.255.255
In 8.4, if I use object nat, the hairpin functionality works perfectly,
object network obj-insideip
nat (inside,inside) static publicip
however, since object nat only allows a single nat statement, I was attempting to use a twice nat to enable the hairpin functionality, but have been unsuccessful in coming up with the right combination of parameters for the functionality.
nat (inside,inside) source static private_object public_object destination static public_object private_object
allows hairpinning to successully work from the same machine. Meaning on any given host, I can ping itself using the private or public ip, but I can't get the right combination for hairpinning from any private host to another private host via the public ip. Other combinations have yielded icmp responses, however, they specify the private IP as the source of the reply instead of the public ip.
There is something wrong with the ordering of our NAT-rules.We are running ASA Version 8.4(2)8 and the nat config is pasted below.
I want outgoing smtp-traffic to be translated to xxx.yyy.zzz.18, but instead it's translated to xxx.yyy.zzz.20 (the outside-interface address).The same goes for ftp-traffic, according to packettracer this is also translated to the xxx.yyy.zzz.20.
Ciscos manual states that static nat rules takes precedence over dynamic nat but that doesn't seem to work for us. [code]
I have recently upgraded my ASA 5510 to 8.3 code and honestly I am confused on the best and most efficient way to do many nat translations through it. I have a group of about 100 IP's that need http/https/and sqlnet allowed through for our web farm.
I have a text file with the real and translated IP addresses and in 8.2 I could simply modify it and dump the thing in and make the NAT rules and access-lists. Now with the new object based model I am having a hard time wrapping my brain around how to do this using as few lines of code as possible.
Do I have to create an network object for each and every IP i want to nat through?
I just tried to do a quick privilege level setup for a user to limit access to asa. User should be able to add nat's to configuration.ASA 8.4 is in question and trying the following does not seem to work:
privilege configure level 3 command object,gives me ,ERROR: specified command 'object' not found in any mode.It looks like localy this cannot be done or I am doing something wrong?
How to configure ASA 5520 to resolve names in ASA's. We are currently using ASDM to configure network objects with the hostnames in the internet and then specifying the IP address . But this is done manually. Is there a different way of setting it up on ASA. Also when getting reports from ASA, we see the IP's but is there a way that we could add an identity to the IP's (reverse lookup)
View 1 Replies View Relatedi have an ASA 5520 8.4(1) with following config
interface GigabitEthernet0/0
nameif WAN
security-level 0
ip address 216.52.185.33 255.255.255.240 standby 216.52.185.34
!
i need traffic (port 9350) from DMZ and WAN forwarded to object Production_23 port 3389, how do i achieve this ?
We have Cisco ASA 5510, I am about to add another 2 Objectgroup network groups on the firewall to our already growing list. Under this Object-group Network xxxx , we are planning to add about about 500 network-object host xxx.xxx.xxx.xxx . This objectgroup will then be applied to an ACL. Just wanted to know if thats possible - meaning addnig 500 hosts? If it is whats the limit?
Also are there any other things to keep in mind before i go-ahead with this huge object group?
We are in the process of migrating to the ASA service modules on both our 6509E switches from our current FWSM. We have used the Cisco conversion tool and applied that to the service module. When viewing the context in ASDM we are unable to view the object names in the right hand pane.
On the FWSM I would see the following under Network Objects:
Network Objects
- JQ-Test
- JQ-Test2
- JQ-Test3
Network Object Group
+ JQ Group
- JQ-Test
- JQ-Test2
- JQ-Test3
Now I have run the conversion tool and applied that to the ASA's I now get the following results.
Network Objects
- 10.1.1.1
- 10.2.2.2
- 10.3.3.3
Network Object Group
+ JQ Group
- 10.1.1.1
- 10.2.2.2
- 10.3.3.3
I am aware that the naming convention on the ASA's are different to the FWSM as you can no longer use the "name 1.1.1.1 JQ-Test1" format but I was hoping that the conversion tool would do this for me.
Is there any way I can get the names of the object back without having to script something that takes the old FWSM format and convert it into an ASA format?
I'm migrating our network objects from our current firewall to a new ASA 5520 configuration. I'm using ASDM 6.4 for configuration.
We have a range of IP addresses for hosts that we need to add to a firewall rule/ACL. In the previous FW software I could create an object that was a range of IP address. For example there is an object called emailservers that is defined as 192.168.2.25-192.168.2.50.
Is there a way to do a similar thing on the ASA 5520?
I can see how to create subnets, but in this case I only have a range of IP addresses, no subnet mask.
I am troubleshooting a s2s vpn between an ISR871 and my ASA5520 and I suspect a problem with my crypto-maps.
Is there a way I can display an access-list on the ASA and have the object names substituted with their IP addresses?
I have a 5540, and i am trying to allow access to internet for an specific network object group, who has inside a bunch of users, who needs direct internet access without any restrictions, i have tried with dynamic NAT, but that configuration ask for a specific IP o a Network range, and is not permitted to configure an object group as a source
The group is located in LAN zone, so a permission from one zone to another zone is needed i think, but i can allow the internet acess to that group Is there another way to get that , different from NAT ?
this is ASA5520 associate with 8.4(1). very simple scenario , three ports: inside . outside . DMZ my problem is how to use network object NAT to perform Regular Dynamic PAT and Identity NAT.
for example, this is my configuration
**** first i configured Regular Dynamic PAT****
object network myinside
subnet 10.200.11.0 255.255.255.0
nat (inside,outside) dynamic interface
**** then , i met problem when i want to make identity NAT between inside and DMZ****
**** if i add below CLI , the first nat line will be replaced ****
**** SO IF I ADD THIS****
[code]......
I ran into a very interesting problem that occurred today and I'm trying to figure out why it happened. If it was one ASA 5505 that just required the reboot, then I'd have just chalked it up to a glitch, but when we built a new AD/ DNS server on the main network at the main site and changed the 3 Remote site ASAs to point to the new DNS server in the DHCPD options, none of them could ping any local host names to the DNS server at the main site they were now pointing too, but external host names { URL} all translated and pinged fine.
From a laptop on one of the remote sites, we could ping the new AD/DNS server(192.168.0.3) and the old AD/DNS server(192.168.0.2) and everything else at the main site, and telnet to port 53 showed successful across the Easy VPN from the Remote site to the new server at the main site. When wire shark was added to the new DNS server at the main site, the DNS request and replies for {URL}, for example, came and worked fine, but any requests for local resources never made it to the server from the remote sites.
A reboot of one of the Remote Site ASA's corrected the issue. Then I rebooted the other two remote site ASAs, and now DNS was working fine for everybody. I had also tried clearing the ARP cache on the ASAs before resorting to rebooting them. I also tried rebooting the laptop thinking the local DNS cache needed cleared before resorting to rebooting the ASAs. I'm struggling to understand why external, public host names made it through and resolved from the remote sites to the new server at the main site, but anything local failed before even reaching the new server(The new DNS server could resolve requests made by computers at the main site, but the remote sites that traverse the Easy VPN from the ASAs failed). The new AD/DNS server is the only server configured for DNS for all remote site computers.
Is any of this making sense? I'm wondering if clearing the x late or local host tables would have corrected it without having to reboot. I'm just trying to grasp the understanding here and figure out what happened.
how to change the order of the groups that are displayed at the SSL VPN sign in page? I am using an ASA-5520. Right now the anyconnect client group displays above the clientless SSL intranet group and I want it reversed.
View 6 Replies View Relatedwhen I migrated the ASA config from 8.2 to 8.3, in all groups the group members has been replaced by the IP address object. However, the "name" for this object has been migrated, but there is the "object network name" configuration missing.
What I can do now is that I can open the new created object in the ASDM, search for the object with this IP address and then enter the object name I had before. When I apply the config, ASDM then creates the object and replaces all affected objects in all groups, by replacing the object group memeber "network-object host hostname" with "network-object object hostname".
Do you know if there exists an automated way, which checks all the groups for members "network-object host", creates the "object network" and replaces the "network-object hosts" with "network-object object" within the group? As long we have a lot of groups which contains partially > 50 members?
it is possible to create a Windows Active Directory group of users which I can use to permit access through the ASA (5520) firewall? I only can find vpn authentication with Radius but nog specific information about granting AD groups internet access via the ASA.
View 1 Replies View Relatedit is possible to create a Windows Active Directory group of users which I can use to permit access through the ASA (5520) firewall? I only can find vpn authentication with Radius but nog specific information about granting AD groups internet access via the ASA.
View 1 Replies View RelatedHow would I go about configuring RADIUS based AAA for remote access VPN users? I have an OSX RADIUS server and an ASA 5510
(I want to keep console and SSH using LOCAL, so I keep this: "aaa authentication ssh console LOCAL", right?)What does the rest of the config look like to get RADIUS based AAA for remote access VPN users?
When I create a service object or group and add the object to a new rule it never works.I mean the traffic match not the rule. I see not hits.I placed the rule on top of my access list to check if I do somethink wrong but it is not working. When I place only a service for example tcp/23 it is working.
my ip service object
object-group service g-as400 description access client 2 as400 machine service-object tcp-udp destination eq 397 service-object tcp destination eq 137 service-object tcp destination eq 2001 service-object tcp destination eq 3000 service-object tcp destination eq 445 service-object tcp destination range 446 447 service-object tcp destination eq 449 service-object tcp destination eq 5010 service-object tcp destination eq 5544 service-object tcp destination eq 5555 service-object tcp destination range 8470 8476 service-object tcp destination eq 8480 service-object tcp destination eq
[code]...
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
I have a asa 5510 vpn client groups configured and connected to the internal network DHCP server stops giving network service dhcp and the network goes down.
View 6 Replies View RelatedI have an issue with LMS 4.1 where the DCR names of several devices repeatedly revert to the IP address. I am trying to stage some devices for deployment. The initial 5 devices were staged and are now off-line. A subsequent set of 6 devices is on-line and accessible from LMS4.1. The device names on the off-line devices are stable. The device names of the on-line devices revert back to an IP address every day. From device management, I go in and change the display name and the host name from the IP address to an alphabetic host name. When I go back and look at it the next day, it has reverted to the IP address.
View 2 Replies View RelatedIs it possible to give me NAS and Xbox 360 Host names so that they show up in my DHCP Client list? Currently there are 13 devices connected, 11 of which have a host name but these two do not. It also shows the IP and MAC addresses of each connected device.I just want to make sure that all of the devices that are connected are what I would expect.
View 1 Replies View Related