There is something wrong with the ordering of our NAT-rules.We are running ASA Version 8.4(2)8 and the nat config is pasted below.
I want outgoing smtp-traffic to be translated to xxx.yyy.zzz.18, but instead it's translated to xxx.yyy.zzz.20 (the outside-interface address).The same goes for ftp-traffic, according to packettracer this is also translated to the xxx.yyy.zzz.20.
Ciscos manual states that static nat rules takes precedence over dynamic nat but that doesn't seem to work for us. [code]
Does the ASA treat an object-group with a network-object containing a range of IP addresses as a netmask? For example, I can apply this configuration without the ASA throwing any errors though the configuration calls for a 'net mask':
object-group network test network-object 192.168.0.0 192.168.63.255 ? network-object-group mode commands/options: A.B.C.D Enter an IPv4 network mask sh run ob id test object-group network test network-object 192.168.0.0 192.168.63.255
I found that in the documentation it requires a netmask as oppose to a range. Is this a bug in the code? I am running code version 8.0(5)23 on a 5520. If this is not a bug how does the ASA treat this type of configuration when applied to an access list? When I ran a quick packet trace and denied access from that range it looks like the ASA doesn't read that configuration properly.
I have recently upgraded my ASA 5510 to 8.3 code and honestly I am confused on the best and most efficient way to do many nat translations through it. I have a group of about 100 IP's that need http/https/and sqlnet allowed through for our web farm.
I have a text file with the real and translated IP addresses and in 8.2 I could simply modify it and dump the thing in and make the NAT rules and access-lists. Now with the new object based model I am having a hard time wrapping my brain around how to do this using as few lines of code as possible.
Do I have to create an network object for each and every IP i want to nat through?
I just tried to do a quick privilege level setup for a user to limit access to asa. User should be able to add nat's to configuration.ASA 8.4 is in question and trying the following does not seem to work:
privilege configure level 3 command object,gives me ,ERROR: specified command 'object' not found in any mode.It looks like localy this cannot be done or I am doing something wrong?
We have Cisco ASA 5510, I am about to add another 2 Objectgroup network groups on the firewall to our already growing list. Under this Object-group Network xxxx , we are planning to add about about 500 network-object host xxx.xxx.xxx.xxx . This objectgroup will then be applied to an ACL. Just wanted to know if thats possible - meaning addnig 500 hosts? If it is whats the limit?
Also are there any other things to keep in mind before i go-ahead with this huge object group?
We are facing the problem in ASDM 5.x creates duplicate network object groups in the configuration when PIX with software 7.0.7 is used. Audit report its showing below commands :
I'm migrating our network objects from our current firewall to a new ASA 5520 configuration. I'm using ASDM 6.4 for configuration.
We have a range of IP addresses for hosts that we need to add to a firewall rule/ACL. In the previous FW software I could create an object that was a range of IP address. For example there is an object called emailservers that is defined as 192.168.2.25-192.168.2.50.
Is there a way to do a similar thing on the ASA 5520?
I can see how to create subnets, but in this case I only have a range of IP addresses, no subnet mask.
I have a 5540, and i am trying to allow access to internet for an specific network object group, who has inside a bunch of users, who needs direct internet access without any restrictions, i have tried with dynamic NAT, but that configuration ask for a specific IP o a Network range, and is not permitted to configure an object group as a source
The group is located in LAN zone, so a permission from one zone to another zone is needed i think, but i can allow the internet acess to that group Is there another way to get that , different from NAT ?
this is ASA5520 associate with 8.4(1). very simple scenario , three ports: inside . outside . DMZ my problem is how to use network object NAT to perform Regular Dynamic PAT and Identity NAT.
for example, this is my configuration
**** first i configured Regular Dynamic PAT****
object network myinside subnet 10.200.11.0 255.255.255.0 nat (inside,outside) dynamic interface **** then , i met problem when i want to make identity NAT between inside and DMZ**** **** if i add below CLI , the first nat line will be replaced **** **** SO IF I ADD THIS****
Is it possible somehow to define externally administred DNS namese in ASA 8.4 in within object groups?i know that we can use name XXX, but some idea popped up using this kind of configuration.
We have an ASA5505 that we need to enable hairpinning on.... In the old firmware versions, we used to be able to configure a public to private static mapping along with hairpinning by using
however, since object nat only allows a single nat statement, I was attempting to use a twice nat to enable the hairpin functionality, but have been unsuccessful in coming up with the right combination of parameters for the functionality.
allows hairpinning to successully work from the same machine. Meaning on any given host, I can ping itself using the private or public ip, but I can't get the right combination for hairpinning from any private host to another private host via the public ip. Other combinations have yielded icmp responses, however, they specify the private IP as the source of the reply instead of the public ip.
I have an ASA5510 where I have defined object-groups and then associated them with a specific ACL. Our ISP is pulling their point of presence from where I live and I am force to move to a new ISP. I am in the process of setting up another interface for the ASA5510 to connect to the new ISP.
My questions is can I create a new ACL lets call it new_access_in and use it with the same object groups that I have already defined? I know that I can only have one ACL bound to an interface, and will bind this new ACL to the new interface I am setting up, but I wasn't sure if I could use the same object groups and connect them to a different ACL. I really don't want to have to create new object groups if I don't have to.
I have an ASA 5510 and have just started using object-groups which are super handy in theory, but not working in reality. I have a service object-group with a mix of tcp, icmp, and udp ports. Let's call it Sample_Port_Group. I'm trying to apply it to my dmz_access_in ACL. Here's the line giving me problems:
access-list dmz_access_in extended permit object-group Sample_Port_Group 192.168.1.1 any
The asa throws up an error between 192.168.1.1 and any. When I put up a ? after Sample_Port_Group, it gives me the option of putting in an IP address, any, etc. When I put in a ? after 192.168.1.1, it only gives me the option of putting in an IP address.URL
Those posts gave me the impression my line was possible, especially the "access-list outsideacl extended permit object-group myaclog interface inside any" line, which is at the end of the 2nd article linked.
We are in the process of migrating to the ASA service modules on both our 6509E switches from our current FWSM. We have used the Cisco conversion tool and applied that to the service module. When viewing the context in ASDM we are unable to view the object names in the right hand pane.
On the FWSM I would see the following under Network Objects:
Network Objects - JQ-Test - JQ-Test2 - JQ-Test3
Network Object Group + JQ Group - JQ-Test - JQ-Test2 - JQ-Test3
Now I have run the conversion tool and applied that to the ASA's I now get the following results.
Network Objects - 10.1.1.1 - 10.2.2.2 - 10.3.3.3
Network Object Group + JQ Group - 10.1.1.1 - 10.2.2.2 - 10.3.3.3
I am aware that the naming convention on the ASA's are different to the FWSM as you can no longer use the "name 1.1.1.1 JQ-Test1" format but I was hoping that the conversion tool would do this for me.
Is there any way I can get the names of the object back without having to script something that takes the old FWSM format and convert it into an ASA format?
After reading the post titled "ASA 5520 nat access-list query for internet access" I realized the object-group command could and should be used to make a more efficient and cleaner configuration. My current environment is very small and straight forward consisting of one FTP server in the DMZ. Though the guide: [URL] is straight forward, my inexperience hinders me from seeing how to use the commands effectively. A summary of the configuration is at the bottom of this post
Question: How can I clean up my current configuration? I have two references to the same server, dmz-rdp and dmz-ftp, created for port forwarding ports 3389 and ftp through the outside interface. I can combine them into one object statement, right? for each port I want to forward through the outside interface?
When ever I create a network object in ASDM 6.0(3) the UI also wants to send the command 'asdm location (network object IP address)' to the device.What is the purpose of 'asdm locaction ....'? Is it telling the ASA-5540 that the IP address is allowed to connect to the device using ASDM?If that is the case why does 'asdm location xxx.xxx.xxx.xxx'get denerated for every network object I create?
When I create a service object or group and add the object to a new rule it never works.I mean the traffic match not the rule. I see not hits.I placed the rule on top of my access list to check if I do somethink wrong but it is not working. When I place only a service for example tcp/23 it is working.
Just planning my move to 8.4(2) and I'm looking for some input. In the past, I have a text file with name commands for every host on my network that I know about. I would then deploy this list to all ASAs so that I could create ACLs on any firewall using a name, which would correlate to the same IP on any firewall.Now, the names from the name command no longer work as a host entry in ACLs, therefore I'm required to switch all of my active name command entries over to objects.My question is, have any of you found an easy way to change all name commands to objects? Since the name command doesn't specify the mask of the entry, I think this may not be possible without manually updating thousands of records. I know that once I migrate, there will be some objects auto-created, but those will only be host and or networks which have NATs associated with them.
Environment: Solaris 10(Sparc) LMS 3.2 RME 4.3.1 CS 3.3.0 CM 5.2
I need to delete a device from CiscoWorks but I cannot find it in the Common Services->Device Management search. I can find it by IP address using the Network->Object Finder . It has an IP address, hostname, display name, and "managed by" information in the search results. Supposedly its managed by: RME IPM DFM(listed twice) However, when I click on the device link , it has almost no tools available (limited to ping) and no device information. I'm hard pressed on how to delete the item withouth having it in Common Services so that I can select it and then click on "delete" . how I can purge this device?
I'm trying to determine who's throttling our 'Outside' interface because it's being hogged.Is there an easy way to see what data is assigned to what object on our ASA5510
On one of my computer i'm having multiple issues. when I am on most websites it pops up " TypeError: object unexpected" or just "object unexpected" and I have to refresh the page for them to go away, but if I hit the back button or go to another section of the web page they pop back up. The same computer is now having connection issues and only has "unidentified network no internet access" as the only option, and after everything I have tried it will not budge on the wifi.
Any way of doing named objects or object groups for ACLs on the ASRs? (1000 series in this case.) I'm setting up an ASR with a zone-based firewall and writing out all the addresses, ports and protocols for the ACLs associated with the various zones is creating huge, unwieldy ACLs in the config.
i have 3560 switch located in warehouse environments . i need to monitor the temperate of this switch . i am looking for OID value that serves this purpose .
kindly provide me how to look for all OID that give me real time status for FAN .. CPU UTILIZATION ...TEMPERATURE ...OR ANY MAJOR EVENT THAT CAN DISRUPT MY PRODUCT IN .
I have 3 ASA 5510s; two of which are in production and the 3rd one is new. I inherited the two in production and was trying to configure that 3rd one using some of the existing object-group network statements. The problem is that when I try to create a range of IPs in one of the object-groups; the range command is not available. Here is one of the statements extracted from one of the production ASAs: object network REMOTE range 62.77.130.14 62.77.130.208.Both ASAs have the same image ver (asa842-k8). Is there something that I am missing to be able to enable the range option on the new ASA?
I'd like to use IP SLAs and object tracking to define static routes for specific source/destination traffic across some WAN links we have. I've done this in IOS and it's worked fantastically, but I've not found where/how to do this on the Nexus 7010 platform (or any Nexus platform) as of yet. I could have sworn that this was going to be introduced in the 6.x code? Below is an example of how we do this in the IOS world:
track 11 ip sla 1 reachability delay down 15 up 15 ip sla 1
[Code]....
Esentially this gives us the option of using a "failover" default route. I've attached a basic diagram to explain what we are trying to do with IP SLAs and object checking. The tracking should be configured against an SLA that uses icmp and the static routes should be configured against the tracking.
In cisco router 2911 how to creat a network object with port permission on ACL. herz what i have done but couldnt succeed in port 22 and 24 should be denied and rest all port services are allowed to outside interface. [code]
I have started to use ip extended access-lists on several 3750X-switches to filter inbound and outbond traffic on the VLANs. But it seems that the use of object-groups is not supported, is this correct? Is it really no way to group different ip-addresses into groups and then use these groups in the access-lists?
