Cisco :: LMS 3.2 / Device Not In DCR But Shows Up In Object Finder?
Oct 26, 2011
Environment: Solaris 10(Sparc)
LMS 3.2
RME 4.3.1
CS 3.3.0
CM 5.2
I need to delete a device from CiscoWorks but I cannot find it in the Common Services->Device Management search. I can find it by IP address using the Network->Object Finder . It has an IP address, hostname, display name, and "managed by" information in the search results. Supposedly its managed by:
RME
IPM
DFM(listed twice)
However, when I click on the device link , it has almost no tools available (limited to ping) and no device information. I'm hard pressed on how to delete the item withouth having it in Common Services so that I can select it and then click on "delete" . how I can purge this device?
View 2 Replies
ADVERTISEMENT
Dec 17, 2007
When ever I create a network object in ASDM 6.0(3) the UI also wants to send the command 'asdm location (network object IP address)' to the device.What is the purpose of 'asdm locaction ....'? Is it telling the ASA-5540 that the IP address is allowed to connect to the device using ASDM?If that is the case why does 'asdm location xxx.xxx.xxx.xxx'get denerated for every network object I create?
View 3 Replies
View Related
Apr 7, 2013
Does the ASA treat an object-group with a network-object containing a range of IP addresses as a netmask? For example, I can apply this configuration without the ASA throwing any errors though the configuration calls for a 'net mask':
object-group network test
network-object 192.168.0.0 192.168.63.255
?
network-object-group mode commands/options:
A.B.C.D Enter an IPv4 network mask
sh run ob id test
object-group network test
network-object 192.168.0.0 192.168.63.255
I found that in the documentation it requires a netmask as oppose to a range. Is this a bug in the code? I am running code version 8.0(5)23 on a 5520. If this is not a bug how does the ASA treat this type of configuration when applied to an access list? When I ran a quick packet trace and denied access from that range it looks like the ASA doesn't read that configuration properly.
View 5 Replies
View Related
Jan 12, 2013
On rv110w, I have 4 vlans. vlan3 feeds a dumb switch and a Wireless AP. When looking at router DHCP leases, it shows devices connected that are not connected. Kinda like it doesn't refresh the list. Set to 50 leases. Questions: Is this normal? How often should it refresh? Is the DHCP time put in as minutes???
View 11 Replies
View Related
Feb 17, 2012
trying to connect to my wifi i set up a password but to enter it wont come up to connect to it
View 1 Replies
View Related
Dec 25, 2011
so many wifi hotspot arround my place, but I can't get all, because need some password for it acces, how to know those wifi hotspot password without asking the provider, and or what kind of powerfull software of the password finder I can use?
View 2 Replies
View Related
Oct 30, 2012
Never seen that before so why is it there and is there a way to get rid of it showing..... tried a couple of "apple" forums with no luck.
View 4 Replies
View Related
Dec 26, 2010
Old Macs had windows locations automatically shown in the Finder under Network. New Macs doesn't. How come and how can I change it?
View 1 Replies
View Related
Oct 15, 2012
I Have asa 5520 with the code 8.0, the mem shows 94% and the CPU shows 85%
View 5 Replies
View Related
Jan 6, 2013
I am using a Belkin AC1000 DB Wifi Dual-band AC+ Gigabit Router with the Belkin Router Monitor on a Macbook Pro (mid 2012) running OS X 10.8.2. I recently installed the router and the Belkin Router Monitor and everything works very well. I have one concern, however: the menu button on the finder bar is not illuminated blue, as it should be, but gray.
View 1 Replies
View Related
Jan 6, 2012
Just planning my move to 8.4(2) and I'm looking for some input. In the past, I have a text file with name commands for every host on my network that I know about. I would then deploy this list to all ASAs so that I could create ACLs on any firewall using a name, which would correlate to the same IP on any firewall.Now, the names from the name command no longer work as a host entry in ACLs, therefore I'm required to switch all of my active name command entries over to objects.My question is, have any of you found an easy way to change all name commands to objects? Since the name command doesn't specify the mask of the entry, I think this may not be possible without manually updating thousands of records. I know that once I migrate, there will be some objects auto-created, but those will only be host and or networks which have NATs associated with them.
View 7 Replies
View Related
Jun 8, 2011
Is it possible somehow to define externally administred DNS namese in ASA 8.4 in within object groups?i know that we can use name XXX, but some idea popped up using this kind of configuration.
View 3 Replies
View Related
Dec 18, 2011
We have an ASA5505 that we need to enable hairpinning on.... In the old firmware versions, we used to be able to configure a public to private static mapping along with hairpinning by using
static (inside,outside) outside_ip inside_ip netmask 255.255.255.255
static (inside,inside) outside_ip inside_ip netmask 255.255.255.255
In 8.4, if I use object nat, the hairpin functionality works perfectly,
object network obj-insideip
nat (inside,inside) static publicip
however, since object nat only allows a single nat statement, I was attempting to use a twice nat to enable the hairpin functionality, but have been unsuccessful in coming up with the right combination of parameters for the functionality.
nat (inside,inside) source static private_object public_object destination static public_object private_object
allows hairpinning to successully work from the same machine. Meaning on any given host, I can ping itself using the private or public ip, but I can't get the right combination for hairpinning from any private host to another private host via the public ip. Other combinations have yielded icmp responses, however, they specify the private IP as the source of the reply instead of the public ip.
View 1 Replies
View Related
Aug 19, 2012
There is something wrong with the ordering of our NAT-rules.We are running ASA Version 8.4(2)8 and the nat config is pasted below.
I want outgoing smtp-traffic to be translated to xxx.yyy.zzz.18, but instead it's translated to xxx.yyy.zzz.20 (the outside-interface address).The same goes for ftp-traffic, according to packettracer this is also translated to the xxx.yyy.zzz.20.
Ciscos manual states that static nat rules takes precedence over dynamic nat but that doesn't seem to work for us. [code]
View 7 Replies
View Related
Jul 17, 2011
I'm trying to determine who's throttling our 'Outside' interface because it's being hogged.Is there an easy way to see what data is assigned to what object on our ASA5510
View 2 Replies
View Related
Jan 3, 2013
On one of my computer i'm having multiple issues. when I am on most websites it pops up " TypeError: object unexpected" or just "object unexpected" and I have to refresh the page for them to go away, but if I hit the back button or go to another section of the web page they pop back up. The same computer is now having connection issues and only has "unidentified network no internet access" as the only option, and after everything I have tried it will not budge on the wifi.
View 1 Replies
View Related
Mar 5, 2012
Any way of doing named objects or object groups for ACLs on the ASRs? (1000 series in this case.) I'm setting up an ASR with a zone-based firewall and writing out all the addresses, ports and protocols for the ACLs associated with the various zones is creating huge, unwieldy ACLs in the config.
View 11 Replies
View Related
Oct 30, 2011
I'm going to replace a Cat6513 with a Nexus 7018. In my Cat6513, there are object tracking config as follows:
ip sla monitor 1
type echo protocol ipIcmpEcho 112.78.254.249
timeout 3000
frequency 6
ip sla monitor schedule 1 life forever start-time now
ip route 172.17.7.0 255.255.255.0 165.202.51.46 name VPN-1 track 123
Is there similar feature in Nexus platform? Because from Nx-OS command ref, I only found:
ip route ip-prefix/mask {[interface] next-hop} [preference] [tag id]
Seems can't associate a track object to a static route in Nx-OS?
View 4 Replies
View Related
Jul 28, 2011
i have 3560 switch located in warehouse environments . i need to monitor the temperate of this switch . i am looking for OID value that serves this purpose .
kindly provide me how to look for all OID that give me real time status for FAN .. CPU UTILIZATION ...TEMPERATURE ...OR ANY MAJOR EVENT THAT CAN DISRUPT MY PRODUCT IN .
View 3 Replies
View Related
Jul 20, 2011
I have an ASA5510 where I have defined object-groups and then associated them with a specific ACL. Our ISP is pulling their point of presence from where I live and I am force to move to a new ISP. I am in the process of setting up another interface for the ASA5510 to connect to the new ISP.
My questions is can I create a new ACL lets call it new_access_in and use it with the same object groups that I have already defined? I know that I can only have one ACL bound to an interface, and will bind this new ACL to the new interface I am setting up, but I wasn't sure if I could use the same object groups and connect them to a different ACL. I really don't want to have to create new object groups if I don't have to.
View 2 Replies
View Related
Jan 30, 2012
I have recently upgraded my ASA 5510 to 8.3 code and honestly I am confused on the best and most efficient way to do many nat translations through it. I have a group of about 100 IP's that need http/https/and sqlnet allowed through for our web farm.
I have a text file with the real and translated IP addresses and in 8.2 I could simply modify it and dump the thing in and make the NAT rules and access-lists. Now with the new object based model I am having a hard time wrapping my brain around how to do this using as few lines of code as possible.
Do I have to create an network object for each and every IP i want to nat through?
View 1 Replies
View Related
May 9, 2012
I have an ASA 5510 and have just started using object-groups which are super handy in theory, but not working in reality. I have a service object-group with a mix of tcp, icmp, and udp ports. Let's call it Sample_Port_Group. I'm trying to apply it to my dmz_access_in ACL. Here's the line giving me problems:
access-list dmz_access_in extended permit object-group Sample_Port_Group 192.168.1.1 any
The asa throws up an error between 192.168.1.1 and any. When I put up a ? after Sample_Port_Group, it gives me the option of putting in an IP address, any, etc. When I put in a ? after 192.168.1.1, it only gives me the option of putting in an IP address.URL
Those posts gave me the impression my line was possible, especially the "access-list outsideacl extended permit object-group myaclog interface inside any" line, which is at the end of the 2nd article linked.
View 2 Replies
View Related
Apr 28, 2012
I just tried to do a quick privilege level setup for a user to limit access to asa. User should be able to add nat's to configuration.ASA 8.4 is in question and trying the following does not seem to work:
privilege configure level 3 command object,gives me ,ERROR: specified command 'object' not found in any mode.It looks like localy this cannot be done or I am doing something wrong?
View 1 Replies
View Related
Apr 6, 2011
webpage error details object required
View 1 Replies
View Related
Feb 5, 2013
Any one know when object-group ACLs will be supported in cat4500 IOS-XE ?? Doesnt seem to be supported now.
View 1 Replies
View Related
Feb 6, 2013
I have 3 ASA 5510s; two of which are in production and the 3rd one is new. I inherited the two in production and was trying to configure that 3rd one using some of the existing object-group network statements. The problem is that when I try to create a range of IPs in one of the object-groups; the range command is not available. Here is one of the statements extracted from one of the production ASAs: object network REMOTE range 62.77.130.14 62.77.130.208.Both ASAs have the same image ver (asa842-k8). Is there something that I am missing to be able to enable the range option on the new ASA?
View 2 Replies
View Related
Sep 26, 2011
i have an ASA 5520 8.4(1) with following config
interface GigabitEthernet0/0
nameif WAN
security-level 0
ip address 216.52.185.33 255.255.255.240 standby 216.52.185.34
!
i need traffic (port 9350) from DMZ and WAN forwarded to object Production_23 port 3389, how do i achieve this ?
View 1 Replies
View Related
Oct 30, 2012
Received Error:Object "Dot11BandSelect" does not exist. when configuring the 802.11 settings on a 4400 WLC runing ver. 6.0.196.0
View 1 Replies
View Related
Mar 18, 2013
We have a Nexus 7010 running version 6.1(2).
I'd like to use IP SLAs and object tracking to define static routes for specific source/destination traffic across some WAN links we have. I've done this in IOS and it's worked fantastically, but I've not found where/how to do this on the Nexus 7010 platform (or any Nexus platform) as of yet. I could have sworn that this was going to be introduced in the 6.x code? Below is an example of how we do this in the IOS world:
track 11 ip sla 1 reachability
delay down 15 up 15
ip sla 1
[Code]....
Esentially this gives us the option of using a "failover" default route. I've attached a basic diagram to explain what we are trying to do with IP SLAs and object checking. The tracking should be configured against an SLA that uses icmp and the static routes should be configured against the tracking.
View 3 Replies
View Related
Jan 2, 2012
In cisco router 2911 how to creat a network object with port permission on ACL. herz what i have done but couldnt succeed in port 22 and 24 should be denied and rest all port services are allowed to outside interface. [code]
View 3 Replies
View Related
Oct 29, 2012
We have Cisco ASA 5510, I am about to add another 2 Objectgroup network groups on the firewall to our already growing list. Under this Object-group Network xxxx , we are planning to add about about 500 network-object host xxx.xxx.xxx.xxx . This objectgroup will then be applied to an ACL. Just wanted to know if thats possible - meaning addnig 500 hosts? If it is whats the limit?
Also are there any other things to keep in mind before i go-ahead with this huge object group?
View 3 Replies
View Related
Nov 4, 2012
We are in the process of migrating to the ASA service modules on both our 6509E switches from our current FWSM. We have used the Cisco conversion tool and applied that to the service module. When viewing the context in ASDM we are unable to view the object names in the right hand pane.
On the FWSM I would see the following under Network Objects:
Network Objects
- JQ-Test
- JQ-Test2
- JQ-Test3
Network Object Group
+ JQ Group
- JQ-Test
- JQ-Test2
- JQ-Test3
Now I have run the conversion tool and applied that to the ASA's I now get the following results.
Network Objects
- 10.1.1.1
- 10.2.2.2
- 10.3.3.3
Network Object Group
+ JQ Group
- 10.1.1.1
- 10.2.2.2
- 10.3.3.3
I am aware that the naming convention on the ASA's are different to the FWSM as you can no longer use the "name 1.1.1.1 JQ-Test1" format but I was hoping that the conversion tool would do this for me.
Is there any way I can get the names of the object back without having to script something that takes the old FWSM format and convert it into an ASA format?
View 1 Replies
View Related
May 29, 2013
I have started to use ip extended access-lists on several 3750X-switches to filter inbound and outbond traffic on the VLANs. But it seems that the use of object-groups is not supported, is this correct? Is it really no way to group different ip-addresses into groups and then use these groups in the access-lists?
I am running sw version 15.0(1)SE2.
View 1 Replies
View Related
