under ASA Version 8.0:Are NAT's processed from top to bottom or general to specific?I have a many-to-many NAT that is taking precedence over a one-to one-NAT. In what order are they processed?
View 1 RepliesMy router is the WRT160N, and it doesn't display the version number on the bottom which according to your website means my router is a VERSION 1.SO, why is it that my router says it has:
Firmware Version: v1.53.0 Dec 19, 2007
And the latest firmware is
Firmware 11/08/2010 Ver.1.02.11
That looks like an EARLIER firmware version to me judging by the firmware version yet it is dated later. **bleep**. If you want, I can upload a photo of my router's model no. for all to see.My question is, am I safe to 'upgrade' to this 'earlier but dated later' firmware version or not? Why is mine showing as having a later version.
Is the Cisco IOS version specific to the number of ports?IE, would a 24pt 2960 switch use the same IOS version as an 8 pt 2960 switch? Or is there a different IOS for each number of ports?
View 5 Replies View Relatedprovide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View Relatedi am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View Relatedwe have some problem with GRE traffic which is processed by CPU and not by CEF.In sniffed packets I can see a lot of "TCP window update" packets. I found that some kind of GRE traffic are forwarded to CPU, like packets with IP options or TTL=0 but non of those are seen in the sniffed packets.
View 2 Replies View RelatedI am implementing traffic export on the WAN interface of my 3725 router. I use a dialer interface for PPPoE which is applied to the Fa0/0 interface. This dialer WAN interface has Zone Based Firewall, NAT Outside, ACLs applied to it, as well as IP Traffic Export for an IPS. In what order would each of these items process a packet? In other words, is the order something like ZBF, ACL, IP Traffic Export, then NAT? How would QoS fit into something like this as well? I am asking because I am wondering how much processing the packets receive before they are mirrored over to my IPS.
View 1 Replies View Relatedi'm working on a QoS troubleshooting issue, I want to know the order how the QoS ACLs will be getting processed.For example I have configured the ACLs AF11, AF12 and AF13, in what order switch will process the ACL? does it in a ascending order fashion?
View 1 Replies View RelatedIf i have 3 x 3560s do i need 3 cables connect one to each other then the top one to the bottom one - like the 3750s stacking stacks -- or is it just one cable between each device no cable between top and bottom
View 3 Replies View RelatedWe have the problem that MPLS labeled packets are not being processed on EHWIC-1GE-SFP-CU if L3PDU + Shim-Header exceeds 1500 bytes.When we move the config exactly to the on-board Interface Gi0/0 it works with put any problems. [code]
View 1 Replies View RelatedI was asked to enable netflow in an ASA Firewall for Orion/Solarwinds server monitoration. Firewall is a 5550, with 4G RAM, and no extra modules but SSM-4GE. This firewall has 5 DMZ segments and ans specific segment for internet traffic.There are segments as unique subinterfaces in physical interfaces. Other segments as individual subinterfaces in the same physical interface (but individual VLANs)Usually firewall CPU flows between 30% to 40%. Rarely to 50%.
1 - How dangerous or risky could be implement netflow in this firewall?...This firewall is very critical for the customer. My concern is regrading CPU, traffic generated, memory, etc
2 - In a month, firewall will be migrated from 8.2 software version to 8.4 software version. Is there any incompatibility in some commands?...Would be recommended to perform netflow configuration after software upgrade?
3 - How could it be implemented for Orion monitoring, regarding each individual sub-interface (and so, each VLAN assigned)?I there any recommendation regarding configuration, best practices?
I recently bought a new XPS One 2710. No problems except that when on the internet the web pages will suddenly drop to the bottom of the page and it is almost impossible to scroll back to the top. This is intermittent. It didn't happen the first week I had it and I have never had that problem with my laptop. Also, the cursor seems to want to move around when in areas that I am going to type in, like to do a search or put in the site name or such. All security is in place, Dell facilitated me with that via the phone.
View 1 Replies View RelatedI reset my E1550 wireless router with the red button under it. Ever since then I can not connect to internet.
View 3 Replies View RelatedYesterday I installed my new E3000 router. After an hour I noticed that de temperature of the bottom was very high and it stil is . Is that normal?
View 7 Replies View RelatedMcAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies View RelatedI own a Dell Latitude D600 that I purchased off of Ebay a few months ago. For the past month I have been having an issue with my wireless card. My problem started when I turned on my computer and booted up and when my desktop loaded, no wireless icon or signal strength showed on the bottom right hand corner where are the other icons are. I went to Device Manager and in the Network adapter section was an exclamation point next to the Dell Wireless 1450 Dual Band WLan mini pci card which showed that there is a code 10 error. I have tried uninstalling it but then I would always get the BSOD with the BCMWL5.sys error. I have tried updating the driver as well but it would tell me that it already is up to date. I have also tried reinstalling my OS but my code 10 error always returns. When I opened up my laptop to see if the card is the cables are loose (which they weren't), I noticed that my wireless card is the Broadcom 4309.
I would also like to ask exactly what order am I suppose to have all of my drivers installed? I am almost positive that I am not installing them correctly. I have seen websites that say to install the Intel Chipset and O2 Smart Card first and then the NSS and so on.
I am currently migrating a netscreen firewall to a asa 5515 version 8.6 The issue is setting up the management connectivity.
basically the management IP of the cisco asa is not advertised. But, we want to route a management IP through the management interface to interface Gi0/2.
so IP of management interface is say - 216.10.100.10. and the IP of the inside interface is say - 198.1.1.10/24 on our router we have a static route sending 198.1.1.0/24 to next hop of 216.10.100.10 (management interface of cisco asa).
On the Cisco ASA can I send the traffic to the inside interface and manage the firewall via ssh that way?
I'm trying to install an ASA 5510 transparent firewall using ASA version 8.4(3)9 but I don't understand how traffic will ever pass through my firewall if both interfaces are on the same sub net(V lan) as the host and it's default gateway? The reason I'm doing this is were installing UAG (or Direct Access) and the UAG appliance need to have public IP's but still be behind a firewall (see attached diagram).
Looking at the documentation (which all seems to be for 5505's running 8.2) it almost seems like i need to have the transparent firewall 'in-line' to the ISP router?, but this router services another IP address range on another v lan for other (routed) firewalls (not shown on diagram) so putting it 'in-line' is not possible. Surely this can't be the case can it? If not how is it supposed to be cabled up and configured so packets go through the firewall?
I use a router RV082 with load balancing. My problem is when I try to access a specific site, I get the error message that my IP address changes and I can not use 2 ip address. I want to specify an ip range to always use the same WAN port.
View 2 Replies View RelatedASA 5520 running 8.0.4
ASDM v.6.1
Need assistance understanding how in ASDM/Configuration/Site-to-Site VPN/Connection Profiles/ "Any Entry" I can specify that I only want to offer an IKE Proposal of pre-share-aes-256-sha?
The IKE Proposal field has a number of possible options including: pre-share-aes-256-md5, pre-share-3des-md5, pre-share-aes-256-sha, pre-share-aes-192-sha, pre-share-3des-md5, pre-share-aes-sha and pre-share-3des-sha.
I am able to pick a specific IPSec Proposal w/o issue but when I attempt to do the same for the IKE Proposal, and click OK the choice does not "stick" but rather returns to the entire list as defined above.
How are asa5540 in high availability mode upgraded for their versions.
View 1 Replies View Relatedconfiguring NAT on intranet firewall. here is the my topology:
DMZ Network - - - - - - - - - External Firewall - - - - - - - - - Internet
|
|
|
Internal Network - - - - - - - - - Internal Firewall
1) I can Ping the intneral host from external firewall, internet firewall and DMZ network
2) Both ASA's are running OS Version 9.0(1)
3) ACL used permit IP any any, on both (i.e inside and outside)
NAT configuration on Internal Firewall (Identity NAT)
object network MGMT-SRV-INSIDE subnet 10.10.10.0 255.255.255.192
object network MGMT-SRV-identity
subnet10.10.10.0 255.255.255.192
object network MGMT-SRV-INSIDE nat (Inside,Outside) static MGMT-SRV-identity
[code]....
I would like to know how can I block a ip address from the CLI at the Cisco PIX Firewall Version 6.3(4)
View 4 Replies View RelatedIs it possible to enable an absolute value rate limit using QOS on a HP ProCurve 5406 switch for a particular IP range on a specific port? Is there a way to configure our HP 5406 with an absolute rate limit on "WAN" port for that server's IP range? I would like to limit it to only being capable of sending 1Mbps worth of traffic over the head end at once.Everything in the documentation points towards priority queues, which as far as I can tell, isn't really what I want.Baring accomplishing this goal using rate limiting is there a better way to prevent our services from accidentally saturating this connection?i thimkong about somthing like that:
class ipv4 rate-limit-port-A1
match ip 10.136.0.0/16 any
exit
policy qos port-a1-ratelimit
class servers-to-be-slowed action rate-limit kbps 1000
exit
interface A1 service-policy port-a1-ratelimit inI'm not sure about this.
I have a Router 2801 with the run conf :
!
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1 192.168.1.63
ip dhcp excluded-address 192.168.1.192 192.168.1.254
!
[code]....
I want to assign a specific IP to a specifig host by MAC .. for example i want the ip 192.168.1.10 to be assign to the host "client1" by mac.I've been creating a new dhcp pool static:
!
ip dhcp pool static
host 192.168.1.10 255.255.255.0
hardware-address xxxx.xxxx.xxxx
client-name client1
!
but the "client1" is still taking other ip.
I have a situation, where I dont need email and where is no SMTP server in this network, but I need CCO-access for EoX/PSIRT from LMS. Because both settings are in the same menu and LMS4.0.1 does real TCP:25 checking for given SMTP-server before can apply, I cant save my CCO-credentials. What can I do?
View 1 Replies View RelatedI wish to set up a ASA5505 with QoS, and to allow specific port numbers to have priority going through compared to rest of the traffic. Eg ports 21, 80, 443. So for example if im maxing out a torrent, it doesnt impact web traffic etc.The current link its connected to is 100mbit/2.5mbit connection..
View 1 Replies View RelatedI need configure destination NAT in my ASA 8.2 version only for a specific origin.
Today, the network 10.84.25.0/24 access the web server with IP 172.17.3.150, i need Nat the IP 172.17.3.150 to 10.96.202.10 only for
10.84.25.0/24 network.
How i can configure this in 8.2 version?
I have Cisco ASA 8.0(5) and I need to block specific url to acees my https server in dmz ?I read about websence technology, but I think it's not free right? Also I read abotu policy inspection map's but in my case is HTTPS not http ..
View 1 Replies View RelatedI have ASA 5510 8.4 Firewall where more than 20 Site to Site VPN Clients are configured on it. how to see the traffic for one Specific Site to Site VPN.Actually this site to site vpn is always keep dropping for every minute. I'm sure its a problem at the other end.The remaining 19 VPNS are UP and working without any problem. How to see the traffic for specific vlan.More over we dont have any syslog server in our network. Is their any chance we can check the traffic on the firewall?
View 6 Replies View RelatedI do have one other question first. What's the effect of the crypto key zeroize rsa command, and then crypto key generate rsa modulus 1024 while I'm SSH'd to the ASA? Can I do it? Or do i need to be consoled in or connected a different way?
ASA 5510:
ASA Version 8.4(1)
asdm image disk0:/asdm-641.bin
asdm history enable
http server enable
http 10.1.1.83 255.255.255.255 inside
http 10.1.1.82 255.255.255.255 inside
Shouldn't that right there be enough to access ASDM from either host .82 or .83? Because I cannot. But if I add http 0.0.0.0 0.0.0.0 inside, then I of course can.
I got a Problem on a customer which is using a Failover ASA 5510 pair with SSM-CSC-10-K9 modules.The clients have to connect to a webserver where they are doing some calculations.If they prepare everything and want to calculate everything what takes a couple of time the session is after about 3 minutes timedout.My first idea was to set session specific timeouts which are a bit longer then the normal but this setting did not work. I created a policy which did not work for me. How to set connection specific timeout's? [code]
View 3 Replies View RelatedWe have an ASA 5510 version 8.3 (2) that we accept VPN users via a radius server. Is there a way to lock down a specific user that connects to the ASA as a SSL client or IPSEC VPN user? If the specific user were to connect to the ASA, we would want the user to have minimal to not access to our system.
View 1 Replies View Related