Cisco Firewall :: Crashplan Backup On Port 4242 Does Not Work With RV180
Jul 10, 2012
I have bought an RV180 Firewall/VPN and try to use the Backup Software Crashplan. As per the supplier it needs Port 443 and 4242 open. Port 443 is fine and allows me to use the service to backup to the Cloud. However when I want to allow other users to backup to my computer this traffic is blocked. I tried to open port 4242 on the firewall and forward the traffic to the computer that hosts the service but it does not work. I have tried to Telnet this port from the WAN but I don't get a response. When I check the Open Ports this port is not listed as a LISTEN port either.
View 1 Replies
ADVERTISEMENT
Aug 12, 2012
Today i installed an RV180 VPN router as replacement for a netscreen ns-5GT.Exactly the same configuration, everything works, except port forwarding from WAN to a host inside NAT.My ports are open (online port-scanner sees the ports as open), the hosts are accepting connections, but a connection can't be made.Probably a bug in the firmware.
View 30 Replies
View Related
Feb 15, 2012
I have a ASA 5510. I setup basic configuration to test internet with 2 ISPs. My first line works with out any problem. But my second line doesn't work. Even when i wipe the configuration, and setup only my second isp. Internet doesn't work. Can you tell me if there is anything wrong with this config?
CaaaA01# sh run
: Saved
:
ASA Version 8.3(1)
!
hostname CaaaA01
domain-name example.com
[code].....
View 2 Replies
View Related
Oct 18, 2012
I have an RV180 VPN router.I try to enable the VPN users with PPTP or QuickVPN but is not working.For PPTP sometimes my windows 7 connects to the router, sometimes doesn't connect with a random error message.When it connects, the windows 7 from outside the lan can see the computers from inside the lan but the computers from inside the lan cannot see the windows7 one. This is random also. When i succed to connect, from that computer, the internet is not working anymore.I tried to set the VPN in the same subnet as lan, i tried with different subnet. Is not working.I updated the last firmware. The same.Restore factory settings couple of times, the same.
View 6 Replies
View Related
Apr 20, 2013
I have been banging at this now for two days and just cannot get Inter-VLAN routing working to work on this router.
Upgraded to latest Cisco firmware (1.0.1.9).Starting with factory default settings, I added 2 VLANS as follows: [code]
BUT....PC2 cannot ping PC3 - NOT WORKINGPC3 cannot ping PC2 - NOT WORKING [code]
View 8 Replies
View Related
Mar 6, 2013
I have a server on the inside of my network (with a internet Routable IP). It has been requested to me that people from the internet access port 80, and that is translated at the firewall to port 7080. I have set up a temp Access rule to allow access to 7080 from the outside and it is accessable. I am not sure what I am doing wrong, but I am tion from 80 not able to get the translato 7080 to work.
View 1 Replies
View Related
Nov 20, 2012
I have a problems with one SA520W.The LAN port don't work correctly. If i connect PC directly via ethernet cable (i try 2 different cable and 2 different PC) the DHCP don't assign an IP. If i reset to factory default and manual insert IP (192.168.75.1) don't work.
View 2 Replies
View Related
Feb 23, 2013
how can I reset the port statitics on the RV180 router without rebooting the router? I have the latest firmware.
View 5 Replies
View Related
Dec 18, 2012
I just installed an RV180 at home. I can not get port forwarding to work - after reading in several forums I realize that I need a firmware 1.0.2.2 that currently is in a beta stage.
View 7 Replies
View Related
Feb 21, 2012
We have ACS 5.3, and trying to set up sftp backup on freesshd server. SSH connection works, but ACS cannot copy backup file to sftp server, we get following errors:
Acs.MGMT.ACSVIEW Backup failed: CARS_XM_SSH_CONNECT : -306 : SSH connect error
FTP backup works fine.
View 1 Replies
View Related
May 27, 2012
I have two servers behind the RV180 and a list of ports I would like to open to the public (80, 443, 21, 3389).In that case, I have to setup 8 Access Rules. I am OK in the first time setting up.But later on, if I would like to change the external IP <-> internal IP mapping, I have to change the Access Rules one by one for all related ports.
Does it has a setting for grouping the ports together so that I can set the Access Rules by one time only ?BTW, the summary view of the Access Rules in RV180 is not very clear, I can't differentiate the Rules for different Destination NATs ... I have to click into the details one by one ...
View 1 Replies
View Related
Jul 6, 2011
why Windows Backup in Windows 7 pro 64 would not backup over the network to a drive I have connected to the 4200s USB port? Everytime I run it I get a Access Denied error at the end, even though data has been transfered. After about 5 hours of searching both here and Microsoft's website, I just get lots of people with the same issue that hasnt been resolved anywhere consistantly.
View 1 Replies
View Related
Dec 17, 2011
We have a cisco 1941 with line t1 Symmetric, (Also have Cisco 1841 unused, but works) I would like to connect the Cisco 1841 to four Adsl Backup lines in case the T1 or the Main cisco 1941 go down I know a BGP is needed on our ISP site,
How can i connect four Adsl lines to The cisco 1841 (Backup) and make them work in a Load Balancing way.
View 2 Replies
View Related
Mar 14, 2012
My company uses Cisco 891's in replacement of the 1811 where we would have DBU used via an external modem and a triggered time of 3 minutes after a primary connection failure was identified. In testing the 891 in a Layer 2 failure environment, it is within milliseconds that the v.92 port is engaging after the layer 2 failure. Has anyone been able to get it to attempt at a more than millisecond rate?
Redacted config from router:
ip sla 1
icmp-echo <%= probeIP1 %> source-interface GigabitEthernet0
[Code].....
View 0 Replies
View Related
Apr 24, 2012
I have a question about 2504 deployment.Two WLC's , one will be acting as primary controller, second as secondary controller.
There will be two firewalls with High Availability between them. Ok, if primary controller will go down, we would need to wait about 2minutes, and AP's would join secondary controller.
But if there is a problem with firewall? Etc. FW 1 goes down. Is it possible with WLC 2504 to use it's second port as backup port ? And use the same IP address between them?
Because if we configure the second port with different IP address, we would need to wait about 2minutes, because AP's is in "rejoining" mode )(To use second port as backup, but have the same IP address on it ( like put these two interfaces into the same "vlan") , because this would be really great, if one Firewall goes down, we would still will be using the same wireless controller.)
View 3 Replies
View Related
Apr 25, 2012
On a WLC 5508 it lists an option to specify a "Backup Port" under the physical information section on an interface. We have two central switched SSID's which are connected to an internal firewall. We are looking at installing a backup/standby firewall and running a virtual firewall between them. Each SSID would have an additional patch from the WLC to the standby firewall.
Does the backup interface port function on the WLC allow traffic to be failed over from a centrally switched SSID via backup interfaces to an alternative device? If this does work will only physical link failure to the primary firewall cause the backup port to be activated or is there configuration parameters which can be specified for load, packet loss or latency which can be used as criteria to cause the backup port to be utilized?
View 1 Replies
View Related
Nov 26, 2012
I have a static IP block and need to route to various servers. I know I can use 1:1 NAT or Access Rules and have success with each. The problem is my mail server. When I use 1:1 NAT, the mail is sent from the correct IP - the address of my mail server - and there is no problem with reverse lookups. However, I cannot block any ports when I use 1:1 NAT. I have tried it every way I can think of and even some suggestions in the forums that did not work. No matter how I set access rules, all port stay open in 1:1 NAT.
If I delete the 1:1 NAT rule and use Access rules to open specific ports, the mail server sends out the mail from the WAN address. The reverse DNS does not match and mail server will bounce the mail.
View 11 Replies
View Related
Jul 10, 2012
I just purchased and installed the RV180 at my office. One of my clients requires that I use Cisco VPN Client to connect to their systems. Before I installed the RV180, everything worked just fine. After I installed the RV180, the VPN client disconnects after 5 to 15 minutes, every time.
What firewall settings on the RV180 do I need to enable/disable so that the VPN Client can work w/o disconnecting?
The RV180 is the router at my office. The VPN Client is on my computer, and I'm connecting to a client's system w/the VPN Client.
View 1 Replies
View Related
Sep 3, 2012
I purchased a RV180 router, and would like set the Firewall Access Rules as below
- Action: Always Allow
- Service: HTTP
- Source IP: Any
- Send to Local Server (DNAT IP): private ip (192.168.1.xx)
- Use Other WAN IP Address: Enable
- WAN Destination IP: one of public ip (different of the router WAN ip address)
- Action: Always Allow
- Service: FTP
- Source IP: Any
- Send to Local Server (DNAT IP): private ip (192.168.1.xx)
- Use Other WAN IP Address: Enable
- WAN Destination IP: one of public ip (different of the router WAN ip address)
The firewall access rules no problem within 1 hour after setting. I can access the http / ftp services by the WAN ip address. After several hours, I can't access the services.
I can set the one-to-one NAT rather than use the firewall access rules, but I would like block all other ports, and one-to-one NAT will forward all ports to the private ip address. Administrator > Logging > Firewall Logs , when I enable the settings, where can I get the log of the firewall?
View 4 Replies
View Related
Sep 8, 2012
Since WLC5508 MGMT interface is configured a AP-Mgr at the same time, can I set a Backup Port to WLC5508 MGMT interface? Refer to WLC configuration Guide:
In the Backup Port text box, enter the number of the backup port assigned to the management interface. If the primary port for the management interface fails, the interface automatically moves to the backup port.
Note Do not define a backup port for an AP-manager interface. Port redundancy is not supported for AP-manager interfaces. If the AP-manager interface fails, all of the access points connected to the controller through that interface are evenly distributed among the other configured AP-manager interfaces
if I need to configure the backup port for MGMT interface, i need to remove the AP-manager on MGMT interface and create a network dynamic interface for AP-Manager ?
View 2 Replies
View Related
Sep 30, 2012
I have 2 RV180's connected via Gateway to Gateway. It works fine when I have the Windows Firewall turned off on both PC's. Obviously this means that I need to have an exception rule in the Windows Firewall in order to use the Windows Firewall. What exception (inbound/outbound) rules that I need to set in order to use the Gateway to Gateway?
View 4 Replies
View Related
Jan 20, 2013
Here's my problem. I'm going to be using Cisco 1941 routers at a bunch of remote sites. All of these sites have 2 comm paths out. Some of them have 2 IP/VHF radios and some have 1 IP/VHF radio and a copper link using Patton ethernet extenders. From the VHF radios the data hit our MPLS network back to our HQ and the sites with copper go directly back to our HQ. Everything ends up at a Cisco 4948 switch. The problem I'm having is that I want the routers at the remote site to use one ethernet port (G0/0) as the primary and the other (G0/1) as the backup interface. I've tried the backup interface command but the problem is that depending on where an outage occurs the ethernet link to either the radio or Patton stays up so it never switches over. We're using OSPF as our routing protocol and I'm sure there's something that can be done with it but I'm not sure what.
View 4 Replies
View Related
May 8, 2012
I am working with a client that currently has an ASA 5505 with two ISPs for failover using a tracked interface. I would like to configure logging so that the ASA will email us when the Primary ISP goes down and fails over to the backup. Here is what I have so far...
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
switchport access vlan 12
[code]....
The primary interface is Outside and the backup is obviously Backup
View 2 Replies
View Related
Jun 13, 2011
I'm having problems configuring an asa 8.2(1) with a backup isp. I followed the asdm instructions in this document: [URL]
I have my backup interface configured as DHCP and the static routes set. Pinging the gateway and other external IP address from the backup interfaces works normally. I have also tried configuring the backup interface as a static address but got the same results.
When removing the primary wan link, all traffic stops. When I ping a external DNS, I get these errors in the log: portmap translation creation failed for udp src inside: 192.168.13.23 dst backup:208.67.222.222_type 8, code0)
I though this type of error is related to a NAT problem, not sure where to look though.
View 4 Replies
View Related
Dec 19, 2012
ASA5510 ios v8.4.I've setup dual ISPs and I'm trying to get ipsec VPN client access to work on the backup interface (outside-backup). The goal is to have outbound traffic on the inside subnet NAT'd through the main interface (outside) while inbound ipsec VPN clients connect and operate off of outside-backup.crypto map is applied to 'interface outside-backup,' however clients are unable to connect. If I switch the default route to go through outside-backup everything starts to work again.
View 1 Replies
View Related
Nov 21, 2011
I have setup ASA 5505 with 2 ISP, named outside (primary) and backup, the scenario is if outside down, then backup will take over, it works now. But it is not working when the primary connection cannot reach the gateway with the interface still up.
Is it possible when the primary connection cannot reach the gateway then backup automatically take over?
My configuration is:
ASA Version 8.2(1)
!
hostname cisco
[Code].....
View 4 Replies
View Related
Jun 3, 2012
I installed a new ASA 5512-X over the weekend for a client. Their backup ISP connection is DHCP based. I need to use the 'dhcp client route track' command on the interface, but it is not available. However according the all the documentation I am looking at and even the ASDM says it should be available.
This is the version of ASA and ASDM they are running:
Cisco Adaptive Security Appliance Software Version 8.6(1)1
Device Manager Version 6.6(1)
I did upgrade to the latest ASA software, so has this command been removed? If I do a '?' in the interface, there isn't a 'dchp' option.
View 2 Replies
View Related
Jun 12, 2013
I have a production ASA 5505 that is working perfectly. I wanted to take a spare ASA 5505 and copy the running config to it so that I would have a backup unit that could be swapped out if the production unit went down.
Both units have security plus and running 8.2(1). The only difference is that the production ASA has 512MB of RAM while the backup ASA has 256MB. Also the backup has anyconnect and the production unit does not.
I copied the running-config to my tftp server and then copied the running config from my tftp server to the backup ASA as startup-config. After reload the device booted with an identical configuration to my production ASA, but after swapping out the units to test it, I have no access to the WAN or DMZ from my LAN. Swapping back to the production unit and all works as it should.
I printed out the running config from both devices and compared them line by line. They are identical except for the anyconnect line on the backup ASAs config file.
View 5 Replies
View Related
Apr 5, 2011
I would like to setup backup ISP in our ASA5510. Right now the the firewall has for default gateway following command:
"route outside 0.0.0.0 0.0.0.0 114.324.321.33 1" i am changing this to route outside 0.0.0.0 0.0.0.0 114.324.321.33 10 track 1 ...so i can setup sla monitoring. As soon as i do the above command and remove the original "route outside 0.0.0.0 0.0.0.0 114.324.321.33 1" from asa then internet connection drops. Right now asa interface Ethernet0/0 has main isp configured and configuring interface Ethernet0/3 as backup. interface Ethernet0/3 name if backup security-level 0 ip address 114.324.321.34 255.255.255.252 no shut global (backup) 1 interface.
route outside 0.0.0.0 0.0.0.0 114.324.321.33 10 track 1 ( Right now in firewall i have" route outside 0.0.0.0 0.0.0.0 114.324.321.33 1 " ) route backup 0.0.0.0 0.0.0.0 115.283.212.23 20 track 2
track 1 rtr 1 reach ability
track 2 rtr 2 reach ability
sla monitor 1type echo protocol ipIcmpEcho 114.324.321.33 interface outside sla monitor schedule 1 life forever start-time now sla monitor 2type echo protocol ip Icmp Echo 115.283.212.23 interface backup sla monitor schedule 2 life forever start-time now. Also our firewall has site to site vpn and 1 main ip configured for exchange and remote access.
View 4 Replies
View Related
Sep 13, 2011
I need to implement the backup between two sites I have router 2800 which is having a point to point connectivity with the far end.At the far end there is no router ,only one firewall is there on that firewall one access-list is there to allow the traffic .To implement the back up link i have created a site to site vpn .But the problem is as soon as the tunnel is establised .For the time being i have removed by site to site config from both firewall.
View 7 Replies
View Related
May 29, 2012
ow to backup Cisco ASA-5510 from a Linux server via TFTP?I do know how to backup a switch or a router. Basically creating an access list such as:
access-list 55 remark PERMIT hosts requesting TFTP access
access-list 55 permit host 172.16.0.27
and allowing access to
tftp-server nvram:startup-config 55
all this inside the router or the switch. From the Linux box just running a simple command such as:
tftp 172.16.0.3 -c get startup-config newbackup.conf
where 172.16.0.3 is the IP address of the switch and newbackup.conf is the name of the config file stored on the Linux machine.So, how do I do that with an ASA box? how to backup ASA from inside it.
View 1 Replies
View Related
Jan 28, 2013
I'm working on setting up a backup link for our ASA 5505 and I've followed these directions: [URL]
The backup ISP gives us a dynamic address, however, when I enable the backup ISP's interface on the ASA, my vpn tunnels drop. As soon as I disable the backup interface, the tunnels come back up. I'm attempting to configure this across one of these tunnels, so obviously this is an issue, as is the fact that other people need the tunnels as well. I'm not sure what I did to make this happen, but I've been over the config many times and can't see anything different from the instructions in the link above.
I thought it might be trying to route traffic across the backup interface, but my primary interface is tracked and has SLA running on it, so I would assume it wouldn't roll over onto the backup interface.
View 1 Replies
View Related
Nov 15, 2011
On our cisco 3750 switches we can take config backups with the archive command. After every "write mem" it rights the config to our backup server. We would like to do this also for our asa 5520 with version 8.2(2). I also searched in the command reference guide, but I can't seem to find the proper command to do it.
View 2 Replies
View Related
