We are having ASA 5550 running on 8.0(5)23 IOS. We are having 2 failover groups group1 & group2. currently all contexts are on group1 & its active & Group2 is in BulkSync mode but from last 2 days the failover for group 2 is happning, i am not able to find anything in logs. Its happing daily from 2 days.
View 4 RepliesWe have ASA 5520 configured for failover and it was working fine. When we wanted to reload the firewall and inactive( Primary) to become Active , we saw that it is in Failed state. The DMZ2 interface in the capture below is the logical sub-interface , but is in Failed State. The other sub-interface on the physical interface Gig0/2 are all fine for the Failed Firewall.
[Code] .............
I am setting up a new pair of ASA 5585's in a multi-context, active/active failover design. I cannot create management SSH connection to the contexts that are assigned to failover group 2. With all the security contexts that are assigned to failover group 1 I can SSH to the inside interface IP and login without a problem. When I try to do that to the group 2 contexts there is no response from the firewall at all, PuTTY just times out.
My firewalls are running version 8.2(4). The contexts seem to be functioning normally in all other respects.
I am looking at deploying a pair of 5585X's in an active/active multiple context state. I am creating Mulitple contexts that need to be able to route to each other. I was going to deploy a type of Gateway context that has a shared interface to all of the other contexts, instead of sharing interfaces directly between the contexts, i beleive this will work as basically i am just cascadng the contexts and sharing interfaces.
The main problem i have come across, is that if i deploy active/active across two appliances using 2 failover groups i can not see a way to route between them, for example.
I have Context 1, Context 2 and Context GW A including the shared interfaces of Con1 and Con2 in failover group 1 on appliance A with the respective standbys on Appliance 2. I have Context 2, Context 4 and Context GW B including the shared interfaces of Con 3 and Con 4 in failover group 2 on appliance B with the respective standbys on Appliance 1.
I need to be able to route traffic between Context GW A and GW B so that the contexts can communicate in normal operation and in failover. I do not beleive that I can share an interface between contexts in two separate failover groups and to be honest without adding a L3 device between the appliances i am not sure if this is possible.
We have three Cisco ASA 5520 with 8.2 code in each tower. There are many configuration on the device hence we are using ip to Name to identify the naming conversion. Out of three one firewall naming conversion is not working, I mean after adding name for a IP it is not reflecting vpn tunnels or access lists or Nat config.
View 1 Replies View Relatedwe have ASA 5510 Configured. this is regarding site-to-site VPN.
View 1 Replies View RelatedWe have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
View 14 Replies View RelatedI am having two ASA 5550 firewall running in active/standby mode. With in last two months our secondary firewall got down automatically 3 times. Firewall is running with IOS version 7.1.2. how to proceed further troubleshooting because there are not any logs on firewall.
View 3 Replies View RelatedOn my old server which I've run Minecraft on for two years now, I've finally shut that down, and am now starting three FPS servers (or trying to) - CoD4, Four Delta One MW2, and Urban Terror... CoD4 is meant to be running though 28960, MW2 through 28961, and UrT through 27960... Although the Four Delta One server seems to be binding to ports and connecting properly, the other two don't. I've tried running the CoD4 server through 28961 as well, but it doesn't seem to show through there either, even though MW2 does. The error is 'WARNING: UDP_OpenSocket: bind: WSAEADDRNOTAVAIL' on both servers.The ports are definitely forwarded.. [code]
View 4 Replies View RelatedIs there any significance to the parameter "firewall-group" in the command
firewall vlan-group <firewall-group> <vlan-id>…<vlan-id>?
In other words is the series of commands
firewall switch 1 module 3 vlan-group 1,2
firewall vlan-group 1 100,101,102
firewall vlan-group 2 200,201,202
exactly equivalent to
firewall switch 1 module 3 vlan-group 3
firewall vlan-group 3 100,101,102,200,201,202
or
firewall switch 1 module 3 vlan-group 1,2,3
firewall vlan-group 1 100,200
firewall vlan-group 2 101,201
firewall vlan-group 3 102,202
All three of these options associate the same set of vlans to the FWSM but using different groupings. As far as I can tell, these groupings have no functional significance either on the switch side or the FWSM side. These are simply three different ways of specifying exactly the same thing? Am I correct?
I want to add new vlan in existing firewall group in 6500. I am confused if it will add new vlan or overwrite.. I am using ASASM module with 6500.
View 3 Replies View RelatedI added this wlc in lms and tried to collect inventory. But it is failing after taking long hours.(LMS Version 3.2.1,WLC 4404 -Version 7.0.116)(SNMP walk is successful & using SNMP V2c)I hope the specific package is available in LMS as i could find the WLC 4404 in Device update->Sys Obj ID -> <id of 4404 WLC> Any bug could be the reson for this...?
View 6 Replies View Relatedvrf ping is not happening between two pe devices in 7609 router having VS-S-2T-10G modules with 15.1 SY1 IOS version? Is there any commands need to add? between pe devides ldp is running properly and ibgp too. I am doubtful about VS-S-2T module.
View 2 Replies View RelatedI have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies View RelatedFor ASA v8.3 and above we don't need to use nat-controll, traffic from high security interface can go to low security interface without matching NAT statements.So does the ASA automatically NAT s the outgoing traffic to the outside interface by default?
For example
ASA inside int---10.1.1.1
outside int---120.11.1.1
when the inside hosts try to go out they will be NATed to 120.11.1.1 by default on version 8.3 and later.is that right?
I try to map LDAP Group to ASA Group policy following documentation:
[URL]
This is a config for ASA 8.0. I would have expected it to work on 8.4 as well but I do run into problems. The mapping as shown in LDAP Debug and ASA Log will actually happen but it is overwritten by the "GPnoAccess" Group Policy configured locally in the Tunnel Group. From earlier works with RADIUS I would have expected the user specific Attribute to be "stronger"?
ASA Log:
AAA retrieved user specific group policy (correct Policy) for user = XXX
AAA retrieved default group policy (GPnoAccess) for user = XXX
I am trying to issue command "ssh key-exchange group dhgroup14" on several of my ASA firewalls. The key-exchange command is failing on 3 of 4 ASA firewalls. According to Cisco documentation, this command was introducted in 8.4. My ASA's are running version 8.6.1.10, 9.1.1.8, 9.1.1.10 and 9.1.2. The command is available only with 9.1.2.
Example from one my ASA.
lbjinetfw# show version | in Version
Cisco Adaptive Security Appliance Software Version 8.6(1)10
Device Manager Version 7.1(2)
Baseboard Management Controller (revision 0x1) Firmware Version: 2.4
lbjinetfw# config t
lbjinetfw(config)# ssh
[code]....
i have been facing strange issue on FWSM (6509 switch). we have created a vlan inteface for server farm on fwsm and its stop responding automatically and we need to give shut/ no shut command under that interface to back into normal .
View 11 Replies View RelatedI have some problem to get working ACLs. The main purpose of this ACLs is to control what is going out from vlan to internet. (For example, i want that only my proxy can access to the web.) So, i use Cisco Packet Tracer and test new rules in lab without any problem.
interface Vlan1
ip address x.x.x.x x.x.x.x
ip flow ingress
ip flow egress
ip nat inside
[Code]...
But it doesn't work on my Cisco 1811w and i dont uderstand why and i'm not sure to have sufficient knowledge to aolve my problem by my own.
My ASA5505 has an external address of x.x.x.13. We have got another 2 spare ip addresses: x.x.x.10 and x.x.x.11.We also have 2 internal hosts, which we need to provide with internet access using NAT. y.y.y.146 and y.y.y.70.
We recently updated our ASA to software version 8.3(1). I was thinking that I could do it using network objects and groups, but didn't understand quite good how this should be done.
The goal is to set up ASA in the way, that if either of the abovementioned 2 hosts will connect to the internet, it needs take one of 2 external addresses. All other hosts should use PAT through x.x.x.13.
I can not have "dns server-group" on my asa 5510, could you tell me how to get this command in my ASA 5510.
View 3 Replies View RelatedI got PIX 525 with failover. Due to power issue one Unit was offline for a while. During this time couple of changes was done on the Firewall.
Which Unit becomes active when I plug the Firewall unit which was offline for a while now. Each Unit has 4 Ethernet Connection
E 0/0 - connects ISP Router
E 0/1 - connects to Lan switch
E 1/0 - connects to DMZ port
E 2/0 - connects to failover unit PIX
Recently i bought asa 5505 to practice for my exams and i failed to connect to internet since my internet provider binds IP and mac for every users and supports only 6 group mac address (xx-xx-xx-xx-xx-xx) format. because asa 5505 has 3 groups (xxx-xxx-xxx) mac address they are unable to provide me the connection.So my question is how can i assign 6 group mac address to asa5505.
View 2 Replies View Relatedi wounder why i'm getting such log message whenever i'm trying to reach my remote site: No translation group found for tcp src outside XXXX dst dmz ZZZZ, i have a Cisco PIX515E firewall and that message is captured there, the traffic is going through a VPN tunnel (the VPN are up on both ends)
View 2 Replies View Relatedi have fwsm in cat6500, i have one firewall vlan group which is in firewall module 1 vlan group 10. I need tocreate another vlan group and add to firewall module 1 vlan group 10, 20. i need to have zero downtime.
View 2 Replies View RelatedCurrently we have one ISP1 and all traffic goes to this way. Suppose our isp1 goes down, our outside user cant get the server. All servers are nated to this ISP1.We planned to purchase a another ISP2. Shall we Configure same inside server to map this ISP2? so that one primary ISP1 goes down it will take place the outside trafficISP2.
View 1 Replies View RelatedHow to configure ASA failover for 8.4.
View 1 Replies View Relateda customer have 2 pix 525 with ver 7.0.1 in a failover configuration with serial cable and 2 sc fiber interface and 2 fastethernet 1 used for failover. the strange behaviour is that when i try to do traffic from inside to dmz or dmz to inside the maximum transfer is 862Kb/s to 1MB/s not more.... i don't understand what's happened. the show mem and show cpu are normal 7% mem used and 1-2% cpu used. attached you will find the configuration.
View 5 Replies View RelatedIs it possible to setup 2 x Cisco ASA 5520 that are in an Active/Standby failover using sla monitoring?
For example ASA1 outside interface connects to an upstream switch and you setup sla monitor with icmp echo to ping that switch. The switch goes down and you need the other ASA2 to become the Active ASA. Can the sla monitor be automatically integrated with the failover commands for this to happen?
I have a ASA 5505 which is connected to a remote site which also has a ASA 5505 over a L2L VPN tunel. One of the sites has a WAN failover configured with two ISP which is working successfully.
But, when the WAN connection fails over to the backup connection the VPN link breaks as the peer site IP address has changed and the VPN can not establish a connection.
Would it be possible to configure a VPN failover so that when the connection failovers so will the VPN tunnel?
There are 2x Cisco ASA 5505 in an active/standby failover config. The primary asa 5505 has been reset and the secondary is now running as active. I would like to reintroduce the primary again but need to know how to do this.
Ideally I would like to remove the failover config and start from scratch. Do I just need to enter the following to disable failover on the active secondary box?
no failover
no failover lan unit secondary
no failover lan interface failover Vlan999
no failover interface ip failover 192.168.254.1 255.255.255.252 standby 192.168.254.2
I have a pair of ASA 5585 configured with 2 contexts, C1 & C2, C1 is active on ASA-1 & C2 is active on ASA-2 i did failover test, ping was initiated to host residing behind ASA-1 in context C1 i powered of ASA-1 then both context became active on ASA-2, however during this failover.i saw 4 ping packets drop..
View 3 Replies View RelatedConfigured ASA 5510 ISP failover and working fine.My ASA as configured as DHCP server also. So its serves IP addressing details including mask,default-gateway, DNS server IPs.Here my issue is whenever my ISP failover occurs my ASA sends previous ISP DNS server IPs to my inside clients.
Here i like to configure my ASA to serve IP addresses dynamically.Or is there any global DNS IP addresses which will work for all ISPs?