i have exchange with NLB cluster.
i want to PAT the cluster ip to access email from outside. i know i can add the static arp entry for multicast cluster ip.
my question is i can add static nat command to that same cluster ip for port 25 and 443 like normal way like we do for normal PAT?
I am trying to configure the NLB multicast for the Microsoft exchange. The moment I am enabling the NLB my core switch 6509 CPU is reaching 100% and whole network getting down. [code]
I thinking I am putting wrong command. I am not able to see the disable-snooping in 6509 Switch.
I am transitioning from a Microsoft ISA server to a Cisco ASA 5510. So far so good, until it comes to getting AAA functioning properly. I have a Microsoft IAS server that is functioning properly, however when I try to test it through the ASA's ASDM it errors out. When I run a packet trace it shows it's being blocked by the dreaded implicit ACL. The funny thing is that I can ping and traceroute to the IAS server from the ASA. I found numerous config examples for AAA using IAS, but still not working.
Could it possibly be behaving this way because my ASA and my IAS server are on two different internal netowrks? (172.31.1.x-ASA, 10.1.1.x-IAS)
We just set up the AnyConnect SSL vpn on our ASA. I am able to establish a connection fine using the Cisco AnyConnect client. I would like to use the native Windows VPN client though if possible. What configuration changes on either the firewall or the client I would need to make for this to happen?
View 1 Replies View RelatedWe have a ASA 5510 which was running 8.0.2, we recently upgraded it to 8.2.5 and since the upgrade remote users for exchange 2007 are not able to download any large email attachments(over or close to 1MB). This is only happening to Outlook anywhere users or OWA users who are connecting to the exchange server using https(443) externally. If the same users connects internally they do not face any issue. When i check the logs on ASA i am gettings lots of RESET-O and RESET-I entries. Looks like the connection between the client and the server gets reset.
View 14 Replies View RelatedWe are upgrading from a Pix 515e to a ASA 5510 with CSC SSM. We cannot send outbound email or receive any email from the outside world. I have placed a call with Cisco Support with no luck. [code]
View 1 Replies View RelatedOur ASA 5510 has been in place for nearly two years, we never have any issue what so ever with it. All along the ASA has been using the default policy. Lately, we beeen getting email deferred in our Barracuda Spam firewall. Google quickly reveals that ESMTP does not play nice with Barracuda witch i disabled eventhough we haven't had any issue with it before. However, the issue remains, we still getting email deferred in the barracuda.
While doing more troubleshooting on the ASA, I constated when issue the command show local-host + IP of the Barracuda, there is an IP address in outside of the interface that can get up to 96 UDP port 53 connections with the Barracuda, this connection never get lower than 20! However, when checking the default setup for the Barracuda, i have the values below:
Incoming SMTP Timeout: 20
Message per SMTP Session : 8
Maximum SMTP Error SMTP Session: 2
Maximum Connection per Client 30m:40
My question is if that ASA show up to 96 DNS session with an outside host to my barracuda, won't that push the barracuda to play email deferred timeout ? Should I change the barracuda default setting? Or should i change the connections limits for the Barracuda in the ASA?
I know that I've run into this before but I can't remember the fix. I have a 5510. The 3 interfaces involved are INSIDE, OUTSIDE, and GUEST. Corporate users are allowed to put their iPhones on the Guest network, but the problem is that their Exchange ActiveSync stops working. It is tied to the external DNS name of the OWA server (we'll say webmail.abc.com). So the users are funneled out one public IP on the OUTSIDE interface and are trying to communicate with the outside of the OWA server, which is NATed to another public IP on the same outside interface. What do I need to do on the ASA to allow users on the guest network (behind the GUEST interface) to access the mail server using its public IP (behind the INSIDE interface)
View 1 Replies View RelatedIs there any way to access a MS Exchange Server 2007 on Windows server 2008 through an ASA 5510 running 8.4 with a full MS Outlook client (not using OWA - web browser)? OWA is currently working fine but I was wondering if access via the full Outlook client is possible and more importantly...is it opening up too many ports on my 5510?
View 1 Replies View RelatedIs there any way to access a MS Exchange Server 2007 on Windows server 2008 through an ASA 5510 running 8.4 with a full MS Outlook client (not using OWA - web browser)? OWA is currently working fine but I was wondering if access via the full Outlook client is possible and more importantly...is it opening up too many ports on my 5510?
View 2 Replies View RelatedI am trying to issue command "ssh key-exchange group dhgroup14" on several of my ASA firewalls. The key-exchange command is failing on 3 of 4 ASA firewalls. According to Cisco documentation, this command was introducted in 8.4. My ASA's are running version 8.6.1.10, 9.1.1.8, 9.1.1.10 and 9.1.2. The command is available only with 9.1.2.
Example from one my ASA.
lbjinetfw# show version | in Version
Cisco Adaptive Security Appliance Software Version 8.6(1)10
Device Manager Version 7.1(2)
Baseboard Management Controller (revision 0x1) Firmware Version: 2.4
lbjinetfw# config t
lbjinetfw(config)# ssh
[code]....
We have the following setup on our Cisco ASA version 8.6.1 One to one NAT rule from outside to our Exchange 2010 cluster IP address (DAG group). This is working fine for clients on the internet accessing their emails via Exchange using their phones. The ASA has the MAC address of the active node from the cluster but when the cluster failover it cache the IP address and are not updating the new MAC when the cluster failover. So users from the outside are unable to connect to the new node from outside the ASA as the MAC address from the passive node is in the MAC table. The MAC address on all the switches update within 2 seconds on the internal network and users don't notice any outage.
View 4 Replies View RelatedWe have a ASA5510 with a webserver in the DMZ network 10.2.2.0/24. We now want this web server to be able to access the Exchange server in the Inside network 10.1.1.0/24. I researched this and it seemed straight forward according the the Cisco document below:
[URL]
I'm looking to do this with smtp so I added these lines to the config:
static (inside,DMZ) 10.2.2.30 10.1.1.11 netmask 255.255.255.255
access-list dmz extended permit tcp host 10.2.2.2 host 10.2.2.30 eq smtp
The configuration line:access-group DMZ in interface DMZ Already existed in the configuration so didn't need to be re-entered.
ASA Version 8.0(4)
!
hostname xxxx
domain-name xxxx.com
enable password xxxxxxxxxxxx encrypted
passwd xxxxxxxxxxxxxx encrypted
names
[code]....
I have the following scenario.
INET
(205.50.50.1)
|
|
(205.50.50.2)
[CISCO ASA 5540]
(10.10.10.1)
|
|
+ ---------------------------------------------+
(10.10.10.2) (10.10.10.3)
[BARRACUDA] [Exchange SRV]
Mail Domain: mail.domain.com (205.50.50.50)
Ok so the mail flows to the Barracuda using a static 1:1 NAT configuration and then gets delivered from the Barracuda to the Exchange server. I want to implement active sync (Direct Push) for Windows mobile devices. They need to communicate with mail.domain.com over port 443. The problem is I want mail to continue to flow to the Barracuda, but direct Direct Push traffic to the Exchange server.I cnow I can't implement two 1:1 NAT mappings from the same external hostname to 2 different servers.
I am trying to port forwarding Exchange 2010 OWA using ASA5505, wherever I used object NAT or Twice NAT it just doesn't work.... here is my config:
access-list outside-access remark "Exchange Server Access Rules"
access-list outside-access extended permit tcp any host <public x.x.x.11> eq smtp
access-list outside-access extended permit tcp any host <public x.x.x.11> eq https
[code]...
note that i use public ip <public x.x.x.9> on the outside interface for PAT, so all hosts in the same private can access internet
I have some users from another company who are visiting my company. The use outlook to access their mail. I think it is via RPC over https (ssl). When there are on my network they are unable to send messages but when the connect to an ISP directly they are able to send. I have a cisco 2821 as my internet router and an ASA5505 (8.0.5...i downgraded it from 8.2.3) as my firewall. I have not blocked anything from going out. Of note is that when other users use window live configured for gmail....which uses tls they are unable to send emails with atachements. Regular emails go though no problem. Hotmail can send atachments without a problem (there is no encrytion there). I have narrowed the issue down to how the firewall treats esmtp or tls traffic passing though it. I have already diabled inspect esmtp on the firewall.
View 2 Replies View RelatedI picked up a rather nasty bit of malware which resulted in a format and installation of Windows Ultimate 64, all well now except i cant get the wireless to work, downloaded assorted drivers from the dell support directory but to no avail, so questions are-:am i missing something obvious (windows function button for wireless does nothing)what is the correct driver for the N5040 and are there any tricks in getting it to work.
View 1 Replies View RelatedWe have a setup where clients on the internal network send/receive their emails through Microsoft Outlook client, while the Exchange server is hosted on the internet, outside the organization.The clients are connected to a Cisco switch, behind an ASA5510 Firewall. The Firewall is connected to an internet router, with double NAT (On the ASA and Router).
the outlook clients disconnect from the Exchange server, sometimes for hours, and then reconnect again. During these disconnections, the same client PCs are able to browse the internet normally. There are no restrictions for the traffic going from the inside to the outside. During the disconnections, if we try to connect using a public IP bypassing the ASA & router,.
I am running ASA ver. 8.2(2) and all users are configured in the ASA. This ASA is uses as a VPN ASA and we are using it for remote access for external users. When a user is logged in, he gets all parameters that are need to continue working from outside, such as, IP, assigned to special group with special permissions and so on. All the parameters that are needed are configured under user attribute. See example below:
username username1 password xxxxxx == nt-encrypted
username username1 attributes
vpn-group-policy Basic
vpn-access-hours none
vpn-simultaneous-logins 1
vpn-idle-timeout 30
[code]....
Is it possible to live the user attributes as is and to force the users to authenticate via LDAP servers only?
I am trying to implement Microsoft LDAP server with our ASA 5520. The client is using Cisco VPN client and when I am trying to connect I am receiving the following error message:
"Secure VPN connection terminated locally by the client. Reason 413:User authentication failed"
I triggered the debug on the ASA 5520 and everything looks fine .The LDAP server is sending the right information without any error message.
Googled this error message and I found that I need to enable the simultaneous logins to enable. I enabled it but I got the same error message. This configuration is under remote access vpn>group-policies>General>more options.
I have an ASA 5505 with the base license,When I setup the DMZ interface I had to add the deny access to the inside VLAN. The DMZ works fine with WiFi on it, but user's iPhones can't get email unless they turn WiFi off.Is there a simple way to allow HTTPS traffic through the DMZ interface to our internal Exchange server which is NAT'd on the 5505's external IP?
View 3 Replies View RelatedI have a computer behind the ASA 5505 firewall. The computer needs to access Microsoft Activation Server. Reading some website information, I need to allow a huge list of servers that basically points to www and https traffic. Therefore, looking at this heavy requirements, I prefer to allow this computer to navigate to any https or http (www) server outside of the firewall.I have included my current asa 5505 configuration. [code]
View 3 Replies View RelatedI ve configures an asa 5505 for remote vpn with anyconnect. it works just fíne - from remote i can ping the Clients and Server inside, i can do RDP or Connect via SSH to any machine, map some volumes local and so on but: I can not connect microsoft sql server. It uses port 1433 for the first connect and establishes then a dynamic connection. So i am a Newbie - what rules or configs do i miss?
View 3 Replies View Relatedmy client wants to make videoconference call thorugh Microsoft Office Communicator, this should be operating between host from one site to another one, but we already configured some rules in the firewalls, and making some test I see that the videoconference use dynamic ports (1024 to 65535) and if we let to operate the videoconference we should remove all the rules in the firewall and that's not the point.
View 6 Replies View RelatedWe have a Cisco secure VPN site to site tunnel between the 2 locations.Which ports are need to open on tunnel so that users can successfully use OCS over the site to site VPN tunnel.All the users are havning the main brach AD account.Using Wireshark captured the packets, found only port TCP 5060, after allowing this port over tunnel I can see the authentication window.The user authentication fails. Already port 3389, 80, 443 are allowed.The main requirement is to only have the Chat, Group Chat and file transfer. Not require AV traffic.OCS is using TCP. no TLS is configured.
View 1 Replies View RelatedI have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 4.2.2.2 i dont get any reply.The runing config is below for ur ref :
HQ-ASA-01# show running-config
: Saved
:
[Code]......
I need to create a firewalled segment that not only separates hosts from general population, but also from each other. The solitary confinement of firewalled segments.I know that I could create a bunch of sub-interfaces, one for each host or group that needs to be isolated, but I'd really rather not have to do that if possible. 1) It could become a management nightmare between ACLs and sub-interfaces and 2) it's a waste of IP addresses.s there any way that I can create a bunch of separate VLANs behind the firewall and have them all terminate at the firewall, using a single firewall IP address for the gateway?
VLAN 1 - hosts 1.1.1.5 and 1.1.1.6VLAN 2 - hosts 1.1.1.7
Firewall DMZ Interface - 1.1.1.1VLAN 3 - hosts 1.1.1.8 and 1.1.1.9
This way, the hosts are isolated and can't talk to each other unless they're on the same VLAN.I'm working with an ASA 5510 running 8.2.4(4).
I have a ASA 5510 firewall with CSC module and Security Plus license for CSC module.Will you tell me how to configure my firewall to send emails to particular mail ID when someone login into the firewall or any virus attacks from outside.
View 6 Replies View RelatedWe were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies View RelatedI would just like to to open UDP port 123 in the ASA 5510 Firewall so that our Primary Domain Controller could use this port to sync time with an external time source. We have already added an access rule for this port under the firewall configuration in ASDM 6.4 and this port was also allowed in the inbound and outbound rule of the PDC's Firewall but it seems that it was still blocked.
View 23 Replies View RelatedI am quite new to firewall, in my company one asa 5510 firewall is there.I configured inside, outside, dns, dhcp and nating.I need to config bandwidth limit (1Mbps) for inside port and I restruct like facebook, youtube and pornsites..And I heard that some subscription is required, really is it required?
View 1 Replies View RelatedI have an ASA 5510 in a live environment. Up til a short while ago I could access this via the ASDM and ssh. However I can no longer connect to it via eithier. When I access It via SSH I get a disclaimer saying the following
*** You have entered a restricted zone! Authorized access only!!! Disconnect immediately if you are not authorized user! ***
It then cuts me off.
When I try to access the ASDM I get the following
The firewall is running all its services without a problem and I can ping the device without any issues. Also none of the config (to my knpowledge has been changed). I set up a console session and http server enable is still there with
http 192.168.200.0 255.255.255.0 inside
I have just configured identity firewall on our ASA 5510.I have 3 nodes that authenticates against Active Directory, using the Windows Server 2008 R2 builtin Network Policy Server: A laptop, a stationary PC, and a Android Phone. All 3 nodes are authenticated using the same user/password.
Now, in ASDM -> Monitoring -> Properties -> Identity -> Users, I can see two of the nodes with my user name attached to it, namely the laptop and the stationary PC.But not the Android phone.
Then it dawned on me. To set up the ADAgent properly, you have to apply 2 group policy entries. Unfortunately, those 2 entries are applied to the Computer Configuraton part of the Group Policy.This means that your COMPUTER has to be a member of your domain for USER IDENTITY to work.So my Android phone and other nodes not a member of the AD Machine Store will never be detected by identity rules, and can roam the network free.
