Cisco Infrastructure :: 3750 - Delay Of Connection
Apr 15, 2012
Actually i have problem with my connection and i would like to find that problem. i have 3 sites(1,2,3) connected together through fiber multi mode cable. The site 1 having the control room, the maximum distance between site (1 and 3) is 1.8 Km, the other distance(1 and 2) is 1.2 km and i already used 3750X switch and GIBIC GLC-FE 100Fx with support MM cable up to 2 KM.
i have in site (2 and 3) 10 cctv 3 mega pixel cameras and i check for the bandwidth is less than 100Mbps when i connected the 2 switches(2 and 3)to the switch in the site 1 there is a delay i thought maybe because of the bandwidth so i tried to connect only 1 camera but the same problem(delay). i did not make any configuration for the switches.
View 12 Replies
ADVERTISEMENT
Jan 26, 2012
actually i have problems with the connection between a Cisco 3750 and P750 server, the Cisco Gbic is X2-10G-SR and the card of the server is 10 Gigabit Ethernet-SR PCI Express Adapter, both uses 850 nm wavelength but i cant see link between the two cards, the physical connection is with a fiber cable with a conector SC in the server and LC (cable adapter) in the switch.
View 1 Replies
View Related
Aug 25, 2012
I had setup a lan infrastructure with 5 3750 stack swithes. In these 3 of them are in one stack which is acting as access switch, 2 of them in another stack which is as core switch where all the SVI is configured. Now, when i tried to ping from our edge pc which is connected in access switch to default gaeway, which is configured in core switch, the ICMP is getting delayed . But when try to ping from the same edge pc to another user PC, it is getting less tahn 1 millisecond icmp replies.
why icmp is delaying to default gateway , but working with another edge to edge pcs without any delays?
View 1 Replies
View Related
Sep 10, 2012
i am facing a problem when the client vlan is commmunicating with the default gateway on the core 3750-x.
ios in 3750-x core is 3750e-universalk9-mz.150-2.SE.bin. But, client to client communication is happening without any dealy and icmp is less than 1 ms always.
When try to ping default gateway of client vlan, it is getting delayed (variable icmp delays). Is this an ios bug?
View 2 Replies
View Related
Apr 18, 2010
Having trouble resetting the baud rate to 9600 on a 3750-E. Basically the device cannot be set to anything other than 115200 baud rate. I have changed this via startup-config (which lost connection) reconnected and saved config but after reload was back to 115200. Tried via bootloader to 'set 9600' but the termial program paused for a bit then the switch prompt returned. Tried the same to 'unset baud' but the same thing as above happened. I have erased and reloaded flash etc
View 8 Replies
View Related
Oct 26, 2011
I've put a C3KX-NM-1G module into a 3750x but can only get ports 1,3 to stand up, ports 2 and 4 dont operate. ports 2,4 are not shutdown and dont come up with working SFPs etc in another switch.
View 1 Replies
View Related
Jul 27, 2011
A customer is expanding their network into another wing, and they have a good number of existing Small Business switches (specifically the SGE-2010P - [URL] that they're interested in possibly deploying. They have a full-blown Cisco infrastructure and voice deployment (Cat 6500 core switches, 3750 switch stacks, Communications Manager w/ over 1,000 phones, etc.).
The general concern is whether there is ANY known issues or concerns with trying to mix/integrate the Small Business equipment with non-SMB infrastructure. Looking at the datasheet for this switch, it's clearly PoE, supports QoS, although it doesn't specifically indicate it can provide a voice/auxiliary VLAN for a phone detected by CDP - that would be a big deal. So basically, "a switch is a switch", and I'm just posing this question to make sure there's no reason (technically or from a support standpoint) that we would not recommend integrating these.
View 1 Replies
View Related
Jan 20, 2013
We have a data center with servers set up for different projects, some servers from partner companies and several small LANs. The traffic between all those needs to be controlled and firewalled. The servers and LANs are divided into different subnets and VLANs. Physically, their traffic is aggregated on a couple of 4506 and then sent to a FreeBSD server, where the logical gateways are set up and traffic is filtered between them.The BSD server is dying and having it there is incorrect in the first place, so we are planning to replace it with two ASA (5520) in failover.The question that arises is how to correctly implement firewalling between VLANs. Originally we thought to set up the firewalls in transparent mode and logically terminate VLANs on a stack of 3750 switches behind them, but would that filter the traffic between the VLANs? Then we thought to perhaps terminate the VLANs on the ASAs, use routing mode, and do filtering there, as well. Or should we implement multiple contexts? We have about 20 VLANs and all of them differ in rules of what should go there. None of this can be concidered an "inside" - trusted - zone, nor "outside". Internet and external links are connected and filtered in a different place.
View 1 Replies
View Related
Nov 14, 2012
I have a 3750 stack as our core switch. On the core switch I have 2 VLANs. One VLAN is for WAN and one is for LAN. The WAN VLAN has our internet router, and the outside interfaces of two ASA's set up as failover. The LAN VLAN has everything else, including our MPLS router for the remote offices. Execs are cheap and want to increase internet bandwidth by purchasing a local home internet service like COX or Time Warner cable to add to our Business internet service with TelePacific which is a bonded T1 at 3 meg. Execs dont seem to care about SLA's and simply will not spend big dollars to increase the pipe. I was looking at those Mushroom Networks appliances but its too expensive for us also. Any way to add additional low cost bandwidth with out current setup? Maybe prefer to keep important internet traffic to the SLA circuit, and then put low priority traffic to the cheap non SLA cable modem if possible.
View 5 Replies
View Related
Mar 29, 2011
I have a very basic networking question If I have, say, 3750's (or any L3 switch, capable of routing) at the edge and a 4500 at the core, where should I route? At the edge? At the Core? Both?
View 4 Replies
View Related
Jul 8, 2012
I would like to limit the bandwidth available to a different target machine. I have been trying to do this on a Cisco 3750, but first I came across this message:
% QoS: policy-map with police action at parent level not supported ...
Then this:
% QoS: policy-map child ... ClassMap BackLimit only support MATCH-INPUT INTERFACE
Is there any documentation, I searched the forum but all I see are complex solutions, I just wanted to limit the bandwidth for a machine that is in a different site. I wanted to apply the policy on an interface SVI.
View 7 Replies
View Related
Jul 10, 2011
We have the next Settings in our SW. We crate an ACL and aplied to a SVI for Incomming Traffic, I understand that is not necesasry to allow the returning traffic in ACL, but we can't access to rdp for example when we add the ACL, if we remove it, the acces is ok, buet when we add again the access is deny, even we have a log entry, and the ACL i just for Incomming traffic. There is no another ACL.
See attached file
[code]...
View 1 Replies
View Related
Sep 28, 2011
Am not finding the resolution to my infrastucture and getting output drops. Sw1 is connected Sw2 as below stated
Please find the conf:
Sw 2 3750 conf:
interface GigabitEthernet1/0/46
no switchport
ip address 172.16.100.81 255.255.255.248(code )
View 5 Replies
View Related
Apr 7, 2011
I have set up an ACL on my 3750 switch to deny icmp from PC A on our inside network to PC B on a different VLAN on our inside network using the following ACLs:
deny icmp host 10.1.17.15 host 10.3.10.4
deny icmp host 10.3.10.4 host 10.1.17.15
-- or --
deny icmp host 10.1.17.15 host 10.3.10.4 echo-replydeny icmp host 10.3.10.4 host 10.1.17.15 echo-reply
These ACLs belong to an access-list that also limits ip traffic to a few specific machines.When I try pinging from PC A I receive a reply message back from PC B. Shouldn't this configuration block any ICMP from PC A to PC B and from PC B to PC A? I would have expected the first ACL statement to block any packets associated with ICMP and when that didn't work I tried the second configuration.
View 6 Replies
View Related
Feb 3, 2013
I need to recover the passwords for my 3750 stack (2 switches), I have the password recovery documentation but it seems to be referring to recovery for one switch. How do I go about recovery when in a stack, should I remove the links on the switches and recover each one separately?Alternatively can I do a factory reset on them
View 1 Replies
View Related
Aug 25, 2012
I have been experiencing a strange problem i have a switch stack of 3750 in which 4 switches are cascaded. there is one one switch shows PROVISIONED status when I run "show switch". i have verified the stack cable connectivity its OK.
now when i try to console that particular switch i am unable to access it as well. I tried to reboot that switch and on reboot it only shows one LED syst blink once and after that remains constant and nothing happens to other LEDS. from the back of the switch FAN is working fine.
View 4 Replies
View Related
Nov 15, 2011
I have a question if I Stack a Catalyst 3750 L3 with a Catalyst just L2, will we able to use all L3 capabilities?
Switches are
WS-C3750G-24TS-E1U
WS-C3750V2-24PS-S
View 4 Replies
View Related
Jul 10, 2012
I have a 1941 Cisco router with WIC-!AM-V2 card that is uning pots( regural phone ) line for data traffic.the problem I am having is the line is establishing connection but it intermittently dropos.The router is configured to dial to Centraal office and I have more that 100 other locations with the same setup that are working fine. The only differene on htis one is it is going thru a PBX line.
View 1 Replies
View Related
Jan 7, 2012
I have a DLSW connectivity between 2800 series router and 7206 router. AS 400 is directly connected to 2800 series router and other server is connected directly to 7206 router. now i want to add one more server which will work as backup for the server connected to 7206 . What would be the connectivity/configuration to make it working in case primary server connected to 7206 is down or connection would automatically needs to shift on its backup server.
View 1 Replies
View Related
Oct 2, 2003
I have at the core a CISCO 4503 and need to connect various 3COM 3300/4400/4900 access switches thru fiber. The problem is that the Cisco core 4503 switch fails to recognize only the 4900 3com switches ie the link status shows down. The fiber multitude link is tested and OK.The modules on both the switches ie 1000baseSX are also tested and ok.
The Cisco switch has a 6port gb ic with 1000baseSX moules and the 3COM 4900 has a 4-port 1000baseSX module.
View 3 Replies
View Related
Jul 2, 2012
I have Cisco Catalyst 6500 with IOS Version 12.2(17r)SX5I need real-time monitornig of failed interface, to shut it administratively down and after 5 minutes "no shutdown" it.I think is good idea to use Cisco EEM for this task.My algorithm is below:
1. EEM script is looking for event about failed interface.
2. EEM script is shutting interface down.
3. EEM script is waiting 5 minutes.
4. EEM script is enabling interface.
I know how to configure EEM for steps 1, 2 and 4, but step 3 I do not.
View 2 Replies
View Related
Jul 11, 2012
I have a big problem with my Cisco 1841 and the WIC-1AM-V2 in Slot 0.I got the task, to test if it is possible, to build up a connection (Dial on Demand Routing) to a remote modem, which is connected to a console port of another Cisco 1841, with the integrated modem card over POTS from the CLI of the router. My router will only dial out to the remote modems and only if its needed.I am connected to the router with the integrated modem card over a console cable on the console port. The remote modem is also connected to the console port of the remote Cisco 1841.
I found out, with my Dialer Profile configuration, it is possible to build up a connection. I configured a dialer list, that specifies that all ip traffic is permitted an interesting for my dialer interface. So a telnet or ping brings up my dialer, which brings up my Async interface. With the "show line" command, I can see that the TTY line, connected with the Async0/0/0 Interface is in use for 5 minutes, because of the "exec-timeout 5 0", which is configured on the remote router. Now the problem is, in this 5 minutes, I can not use a remote telnet on this line with my loopback interface, because the line is already in use and I get a "connection refused". The first telnet I use runs in a timeout, because the remote host is not responding. When I dial out directly from the modem card and not from the CLI with the AT-commands, I get also the connection and with a return i get the login prompt. I will post my actual config, so that you can see maybe a mistake I did or which command I must use, to get a working connection. [code]
View 6 Replies
View Related
Jun 17, 2012
I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
View 5 Replies
View Related
Jan 8, 2012
i want to know the definition of "Routing Delay in a network".
View 1 Replies
View Related
Jan 24, 2011
I am encountering delays when making any calls using VOIP. I understand that there is always a delay using VOIP but not as much. I've done a bandwidth test on my network and everything seems to be Ok, we have 4 T1s with 55 Reps using it. There is nothing choking up the network.
View 3 Replies
View Related
Sep 17, 2011
I've got a strange problem with my internet connection. I have recently moved and brought my desktop with me. While I am able to connect to the internet in my new place, a weird problem arises: whenever I try to access a new webpage, there is a consistent 5-10 seconds delay before the page actually loads. After the initial delay however, the webpage will load quickly. This problem will repeat itself whenever I try to access a site that is not cached. I have tried switching ethernet cables/wireless adaptars and this problem persists. I have also tried scanning and cleaning my computer yet nothing works. Speedtest.net show that my ping, d/l and upload speed are all fine.
PS: Just to add some information, my new place comes with its own existing router (the building includes internet into its rent), and I am simply plugging an ethernet cable from my computer to it. In addition, my roomates and my laptop seem to be able to access the itnernet fine with this problem. Since this sounds a lot like a DNS problem, I have also tried using OpenDNS and that doesn't work either. In addition, the delay persists regardless whether I am trying to access a website via its domain name or numerical IP address.
View 3 Replies
View Related
Apr 23, 2013
Any good way to force a serial link to delay packets to simulate a hi latency WAN link? Found this command so far:
Router(config-if)# transmitter-delay hdlc-flags
I can dial the speed up/down via clock rate all good but I need to also simulate latency. This is for simulating a WAN bonding scenario so I was going to aggregate a 10M ethernet port with a 2M serial and a 512k serial. But I need to also ensure varying latency.
View 2 Replies
View Related
Jun 6, 2012
I have an issue with a Cisco ASA 5520. It seems to block some emails incoming from some recipients. The sender's mail server clearly reports my ASA as cause of the problem (see attached image). Unfortunately I have not the logs about that event and the time frame to close this issue is very narrow.
View 5 Replies
View Related
Mar 11, 2013
Core Internal Network -> Cisco ASA 5510 -> DMZ Switch.If i send a ping reguest from internal network to servers in DMZ Switch over the ASA 5510, i can see a delay in response, some times this delay can be more than 80ms, this is a problem for the web applications in http traffic.How i can find what's happening on my ASA? I disable the inspect traffic over the IPS, disable the policy maps below, reload the two boxes, but doesn't works, the problem still persists. [code]
View 2 Replies
View Related
Oct 1, 2011
The wan routers are 2600 and 1700. Conversions between the two? Pros/Cons of one versus the other? Regrets or horror stories for one versus the other?
View 3 Replies
View Related
Jan 8, 2013
i'm having some problems to configure.i have two sites, a primary site and the secundary site, in both sites every switches are layer two. I configured and activated the RSTP (802.1W) in every switch, but about every 30 minutes the topology change and happening a delay in network and loss some ping (ICMP).
[Code]...
View 2 Replies
View Related
Jul 16, 2011
I have one problem with our windows 2008 server when any user want to log in the domain from his computer, it takes long time. it takes around 5 minutes. I have installed DNS on the same AD Domain. Is that OK ?Secondly i have around 70 users and 4 ISPs.. Each ISP is used for specific data transfer. Each of the ISP is connected via ADSL Router to our switch?
View 3 Replies
View Related
Nov 6, 2011
I have a wierd "2 second delay" issue with audio generation on a SRP527w.When in a call, with myself on both ends of the setup DECTphone - FXSport on SRP527w - VOIPprovider <> PSTN/GSM - Mobile I can hear my voice on the mobile immediately, as expected. However, the same words i speak (having both the DECT and the Mobile at my ears), are heared on the DECT with 2 seconds delay. Trust me when I say that this is the base for a poor rated telephone call and misunderstandings therein.
This issue is the same when calling to other mobiles and even land-lines, both in being called and being the calling party... Every time the voice from the other side is heard "delayed" on the DECT. Testing the DECT on a normal non-voip connection results in a normal conversation, as far as this is possible with me talking to myself I do have a separate CBR pvc for the voice on the SRP and to investigate the issue I've put the SIP user on a soft client, using a UBR pvc on the same SRP, both pvc's do use the same provider but diverend gateways. And with the UBR + softphone i do not have this "2sec delay" issue.
So, ruffly said this seems to locate the issue in the SIP>FXS DSP, with specific only the digital>analog decoding/generation (not with the analog>digital encoding, as i hear myself normally on the mobile, with no/normal msecs delay).
View 4 Replies
View Related
