Cisco Routers :: RV042G Difference Between Bandwidth Protocol Binding For WAN

Oct 15, 2012

What the differences are between bandwidth management on WAN ports and protocol bindings?

If you can specify in each section which protocol should go where why having two places to configure this?Or are there some things to remind when using one of them?                  

View 3 Replies


ADVERTISEMENT

Cisco Routers :: RV042G - Protocol Binding And VPN With Load Balancing

Oct 6, 2012

I have dual WAN connections on rv042G in "office 1". LAN is 192.168.10.x
 
A gateway to gateway VPN is made with another "office 2" on rv042G too.
 
The goal is to reach the LAN of the other "office 2" : 192.168.5.x
 
Working good. Now I need to use protocol binding : One LAN ip need to use WAN 2 : All traffic :192.168.10.77~77(0.0.0.0~0.0.0.0)WAN2 -> Working
 
The rest of LAN should use WAN 1 (same as the VPN) When I create this rules, I can't reach the "office 2" LAN : All traffic : 192.168.10.100~150(0.0.0.0~0.0.0.0)WAN1

What should I do to make it works ?

View 13 Replies View Related

Cisco Routers :: RV042 Protocol Binding For SIP And RTP (VoIP)

Jun 26, 2012

I have a RV042 with a DSL (WAN1) and cable (WAN2) internet connection in Load Balance Mode. The DSL provider also provides internet telephony when registered via his line. When I disable the WAN2 port, my IP phone successully registers with the registration server of the DSL provider. I also defined protocol bindings for SIP (port 5060) and RTP (ports 5004 to 5020) to be bound to WAN1. My IP phone is set up to listen on only these ports. [code] With these protocol bindings in place when I re-enable WAN2, then after some time the phone reports "registration failed".Do I need to set something else apart from protocol binding to force the VoIP traffic to go via WAN1?

View 23 Replies View Related

Cisco Routers :: RV042 Protocol Binding Multiple LAN Subnets?

Aug 16, 2011

We have Point to point T1 environment where 3 additional WAN sites get internet access through our RV042. When we setup load balancing we have problems with https traffic, so we setup protocol binding for https and everything worked great from the local LAN. When trying to access https content from the remote LAN across the WAN the sites failed and I see no option to add additional subnets to the protocol binding. Is there a command line feature that supports adding additional subnets for protocol binding or is the local LAN the only option?

View 7 Replies View Related

Cisco Routers :: ICMP (ping) Protocol Binding With The RV042?

Aug 7, 2011

Is it possible to use protocol binding to route pings only over the WAN1 connection, even if WAN1 fails? It seems like the protocol binding feature of the Linksys RV042 is ignored once WAN1 fails.  I would like to use a ping from the LAN to an external IP to verify if the WAN1 connection is down, or is up and then use that information to power up, or power down a secondary communications system (WAN2).  However, if the protocol binding is ignored when WAN1 fails, then I will not be able to use the ping to establish the state of WAN1 connection. Addtionally, is it possible to use protocol binding to only route pings and allow all other traffic to use either WAN connection? I have seen these feautures on a different brand of router that failsover to a cell connection, but it is not a true dual WAN router. It would be nice if the RV042 would allow this kind of control. Are there any other dual WAN routers out there that have this kind of protocol binding feature?

View 1 Replies View Related

Cisco Routers :: Dual WAN Router And Protocol Binding RV042/G

Jan 7, 2013

I'm in the process of finding a dual WAN router with VPN support, that allow me to redirect some traffic to one specific WAN port and do load balancing of that specific traffic in case of that WAN failing (this last requirement is preferably but isn't fully needed).
 
Does the RV042/G could work with that? In that case, does it allow protocol redirect only? What about ip/ports redirecting? Or some kind of packet filtering to redirect to specific WAN ports?

View 6 Replies View Related

Cisco Routers :: RV042 Load Balance Protocol Binding Not Failing Back

Mar 6, 2013

I am trying to make this router prefer Wan1 for outbound while listening to both WAN ports for Inbound. I set it to Load Balance mode and added in a rule for Protocol binding:
 
All Traffic( TCP & UDP/1-65535)>192.168.1.1~192.168.1.254(0.0.0.0~0.0.0.0)WAN1 ENABLED
 
This says bind all Outbound traffic  to anybody to WAN1
 
My Wan 2 connection is over satellite so it is easy to tell if a ping is going over Wan2 because the latency is >600mS
 
If I start a continuous ping to outside site - eg Yahoo.com then if I Fail WAN1 I see the ping latency Jump from 30mS to 700mS  as it starts to use Wan2. If I restore the Connection to Wan 1 then the pings stay on WAN2 - seemingly forever. If I stop pinging for 30 mins then a restart of pinging does use Wan1 - so it fails back eventually If I restore Wan1 and then remove Wan2, it fails back right away
 
My problem is with our VOIP which uses a connection keepalive  so there is no real downtime for the router to release the path to WAN2 should it fail over how I can force the router to fail back to Wan1 without removing Wan2?

View 3 Replies View Related

Cisco Routers :: RV082 V3 Load Balancing (Protocol Binding) With IPsec Tunnel?

Mar 14, 2013

We have tried a variety of options in an attempt to use Load Balancing (Protocol Binding) with an RV082 that has a site to site IPsec tunnel with another RV082. Both are v3.
 
Here is the issue. We have dual ISPs, one has great bandwidth, but we incur overages. The other has mediocre bandwidth, but has unlimited usage.
 
GROUP1 - We want most PCs to use the "unlimited" ISP for general surfing, email, etc. (Bound all ports for range of internal IPs to ANY dest to WAN1)
 
GROUP2 - We want to use the "faster" ISP for our VPN tunnel (mostly RDP and SIP traffic). (Bound all ports for range of internal IPs to ANY dest to WAN2)
 
So far everything works. The router will route traffic appropriately and GROUP 1 uses WAN1 and GROUP 2 uses WAN2.
 
Unfortunately, sometimes GROUP1 users need access to resources over the VPN (WAN2).
 
There is something not right with the routing. For example GROUP1 can ping and receive responses from devices on the other side of the tunnel, but GROUP1 can't access intranet sites on the other side of the tunnel. They also can't RDP to PCs on the other side of the tunnel.
 
Why does the router correctly route ICMP, but not RDP?
 
We've tried adding additional protocol binding rules for specific ports(80, 3389, etc) and ip ranges (both local and remote) to see if we could force GROUP1 traffic destined via VPN through WAN2, but it doesn't work.
 
Shouldn't VPN tunnels created and configured in the RVs not adhere to protocol binding? It just seems logical to me, but maybe I am missing something.

View 7 Replies View Related

Cisco Routers :: Server Access Through RV042G With SMB Protocol On MAC 10.6.8

Sep 4, 2012

Our lab recently purchased a RV042G to setup a subnet (I don't know if this is the correct term) within our company's network. Eventually we like to put a dozen computers on this subnet along with a 24TB NAS drive for data storage. We like the computers in the subnet to be able to access the company's numerous servers.
 
To test the router setup before going all out, I have a WinXP SP3 computer and a MAC OSX 10.6.8 computer hooked up to it. Both computers can access the Internet just fine. The WinXP computer can access company servers thru the RUN command ("\servernameshare"), but the MAC is having issues with the SMB protocol ("smb://servername/share"). The same MAC if plugged directly to the network has no issues connecting to the company server.
 
Is this not working because the RV042G doesn't support SMB? or did I do something wrong with setting up the router? By the way, firewall is turned off, since the company already has its own firewall.

View 1 Replies View Related

Cisco Routers :: RV042G V3 Protocol Bind All HTTPS Traffic To Wan1

Jun 12, 2013

If you are using load balancing how do you bind i.e. all HTTPS traffic to i.e. wan1. RV042G V2 you can inter 0.0.0.0~0.0.0.0 as Source IP to forward from all IPs, how do you do that with a V3?

View 2 Replies View Related

Cisco Routers :: RV042G WAN Bandwidth Has Only 100Mps?

Jul 8, 2012

I just got the RV042G today.  I found the router can only accept 100000 Kbit/sec as bandwith, which is 100Mps only.  According to the specification, it should have 1000Mps WAN.  I have a internet link of 1000Mps, which is now limited by this router. 

View 30 Replies View Related

Cisco Routers :: Dual WAN RV042G Unreachable After Configuring Bandwidth

Mar 17, 2013

I bought a RV042G router some days ago to manage 2 adsl lines at my home. Everything works correctly except one thing : i can't configure the bandwidth management. When i go to "Bandwidth Management" menu, then "Bandwidth Management Type" then i choose rate control or priority and i a had some rules to priorize http protocol for example, then i click on save button. After a few seconds of internet usage i loss connectivity to the router and internet and 192.168.1.1 became unreachable to ping. I had to unplung the power cord to restart the router, the same problem still occurs until i remove all the rules ! Some times i even had to do a factory reset because my adsl modems are unreachable behind the router (unable to ping the gateway).

View 4 Replies View Related

ARP List And Binding Setting Under IP And Binding In Router

Mar 21, 2011

There are list of ips and corresponding mac address in ARP list and Binding setting page of the routers in our company.

I would like to know what it is meant for. This was done by our network admin. I would like to learn about it.

View 2 Replies View Related

Cisco Routers :: RV042 / RV042G / Small Business Routers With Inter-VLAN Capability

Aug 22, 2012

I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?

View 5 Replies View Related

Cisco Routers :: RV042G Can't Get A New IP

Mar 3, 2013

my router (RV042G V01 Firmware Version : v4.2.1.02 ) get errors I can't understand.Lost connection, can't get a new IP, DNS does not work, total hangup.After a short time / reset everything works fine up to the next error.In the Log I found the following interest entries:undefined Kernel undefined Kernel failed (1).undefined Kernel Message from server.

View 1 Replies View Related

Cisco Routers :: RV042G One-to-one NAT?

Sep 24, 2012

I purchased RV042G and setup one-to-one NAT problem to several servers. ometimes the NAT servers lost the internet connection. My case as below
 
ISP provide two set Public IP Address , one modem
e.g.
set one) 100.100.1.2-6, gateway 100.100.1.1
set two) 200.200.2.2-6, gateway 200.200.2.1

[code]....
 
All computers and servers (one-to-one NAT) outbound and inbound all work fine. After several hours, only the servers (one-to-one NAT) alert internet connection broken, but the computers (non NAT) still have internet connection.
 
What's the problem occurs? Why only one-to-one NAT servers lost the connection? and Why only serveral hours later, the server lost the internet connection.
 
If I changed the WAN setting to same as subnet of the one-to-one NAT, it doesn't occur any problem.

View 3 Replies View Related

Cisco Routers :: RV042G DMZ For WAN 2?

May 20, 2013

I run my business network on the 192.168.x.x range with a server set as 192.168.2.4 statically. The router is currently connecetd to two DCHP wan connections from my ISP, I'm on a residential consumer plan. It has defaulted to loadblanacing with the second WAN however I want to have the second wan's public IP be used by my server and only the server however I wish for the server to still be on the lan so I can use HYPER-V's brided network connection feature to run VMs on the lan, and I would like their wan connection to be from wan 1... as for the entire lan except the server at 192.168.2.4 Is this possible, I can't seem to get the 1-to-1 NAT to do it?

View 4 Replies View Related

Cisco Routers :: RV042G Can't Connect Another PC

Nov 8, 2012

I've setup the RV042G with one ISP connection for now.I have my main PC running fine, but I have another PC hard lined to the router that had a connection after I power cycled the modem and router but now it no longer does. disabled the network on that PC, now I can't get it back at all.I have a wireless e2000 in one of the ports that I disabled the DCHP on and it seems to be running nicely.before I disabled the PC in question, aka port 3, it was showing as connected in the "192...." but now only as enabled.

View 1 Replies View Related

Cisco Routers :: Net Flow On RV042G?

Sep 27, 2012

Is there anyway to monitor netflow on RV042G.  We have a network at a small school that will get bogged down during the day.               

View 1 Replies View Related

Cisco Routers :: RV042G And Public IPs

Feb 6, 2013

I have an issue with routing public IPs on the RV042G.  I have been able to route the IP's in a couple of different ways, but there is always a nagging problem. 

I have a PPPoE Business Class account with 5 routable public IP's.  I would like to route the IPs and manage the private network using the RV042G. 
 
Here is what I have tried and the problem that arose: 1)  I used 1:1 NAT and the servers responded with no issue.  This would be a workable config however I use Kerberos for single sign-on for my clients.  To use this security protocol and bind the clients to the server, I must use a public IP on the server machines.  In this scenario however, everything else worked fine.  2)  I then tried using the DMZ and putting the servers on the DMZ port with a public IP entered in the network config of the machine.  That even worked fine and I was excited until I noticed that the servers were reporting the public IP assigned to the DMZ port as their IP when they sent mail.  I then ran a test and that is the case.  The servers - each with a public IP - are reporting the IP of the DMZ port.  I can't have that because the mail servers need to announce a correct IP so the reverse lookup will match.  Once again, a little gnat gets in the soup.

View 2 Replies View Related

Cisco Routers :: Rv042g Cannot Add To List On One To One Nat

Apr 22, 2013

Have a rv042g, newest firmware, trying to setup one to one nat on the configs page, I select enable, enter private ip , enter public ip, enter the range, and click "add to list"  and nothing.... no error message, doesn't add to the list below it

View 1 Replies View Related

Cisco Routers :: RV042G As A VPN Client?

Jan 29, 2013

I have RV042G dual WAN VPN router as a gateway in my small office. My ISP requires from me to connect through PPTP VPN to have access to the network. I've configured my router with static IP and every time I connect a laptop or desktop pc I need to connect to the VPN with the Windows VPN client.

View 3 Replies View Related

Cisco Routers :: RV042G - Out Of Memory When Using VPN

Oct 4, 2012

We have recently purchased a brand new RV042G VPN router, set it up, and had it running for a while without issues.
 
Now that we are actually trying to use the VPN functionality, the router becomes unstable after a while, showing "out of memory" lines in the logs, and after a day or two the VPN stops working completely and the web interface becomes completely inaccessible.
 
This issue happens when using any sort of VPN that's supported by the router.

View 1 Replies View Related

Cisco Routers :: RV042G FTP Still Goes Through WAN1

Oct 17, 2012

I have created a protocol binding rule and even a bandwidth rule to make sure outgoing FTP needs to go through WAN2 interface. But it still goes through WAN1, it only works when I disconnect WAN1

View 13 Replies View Related

Cisco Routers :: RV042G DNS Stops After Few Hours?

Mar 16, 2013

I have a problem with the RV042G V01 router manufactured 12/2012.
 
After router settings the router works fine without any problems. After 10 or 12 hours I got the message that the side could not be opened, while no DNS. I checked inside the router and all settings looks ok DNS adresses from ISP are present on both WAN settings . When I use inside the router the funktion for DNS it will work but from any client is does not work. When I restart the router alls works fine. After few hours ( it's differnt 1,2 or 6 ) I have the same problem. No entry in the log's !

View 7 Replies View Related

Cisco Routers :: RV042G Can't Forward SSL Port 443

Aug 26, 2012

Recently setting up a RV042G for my SOHO. Everything seems to be fine except for SSL port forwarding. I know the router's external static IP is reachable because I test it out with remote management functionality from an external IP. Port forwarding also works correctly because I have other behind the router servers in both UDP and TCP working flawlessly. PPTP VPN also works corrrectly. What I can't get it to run is an Apache server. Looks to me RV042G kind of drop all SSL or HTTP ports from the WAN side.
 
Configuration:

- 4 port forward rule under "Setup/forwarding" for 80/8080/443 and 8443 all to the webserver with a static IP.

- Firewall page I have Firewall, SPI, DoS enabled.

- Added a firewall rules to allow all HTTP and  HTTPS traffic from WAN1 to the webserver static IP.

- Toggle Block WAN Request, HTTPS and multicast does not affect the result.

- Toggle and mapping the remote management port to other port beside 443  does not affect the result.
 
The same setup will works corretly under my old Netgear FVS router. Am I missing something in RV042G setup?

View 3 Replies View Related

Cisco Routers :: Possible To Use RV042G For Attached Topology

Mar 24, 2013

I'm trying to make an attached topology. This router should be attached to 2 different ISPs on both WAN interfaces (ISP1 with IP address - A.B.C.D, and ISP2 with IP W.X.Y.Z) and I want to use DMZ, too. My idea is to make a L2/L3 segmentation with 2 VLANs - Vlan RED for DMZ (private network 192.168.1.0/24)  and vlan BLUE for Internal network (network 192.168.2.0/24). I checked in the manual that vlans are supported, but I can't see anything about 802.1q, can I use one trunk port or I should use 2 physical cables?
 
There should be inter-vlan routing and basic stateful firewall, so PCs in Vlan Blue should be able to initiate connections to DMZ servers, but the opposite should be denied. Router should make a port forwarding on its both WAN interfaces and forward incomming traffic (from Internet) to DMZ servers (with NAT). Both DMZ servers and internal PCs should have an internet access with NAT over both WAN uplinks.
 
Can I use RV042G for this setup and if not at all - are there any cisco SMB device which can do this?

View 5 Replies View Related

Cisco Routers :: How To Configure IPSec VPN With RV042G

Nov 11, 2012

How to configure an IPSec VPN with router RV042G.I need to know how to configure an IPSec VPN. Cisco Router with RV042G.
 
I spend this client your VPN parameters. [code]

View 2 Replies View Related

Cisco Routers :: Configuring VPN Connection On RV042G

Nov 4, 2012

i got a problem in configuring a VPN Connection for our Colleagues (Laptops & Iphones 4/4S/5) We got an RV042G .
 
A WAN Connection from Deutsche Telekom AG with Static IP connected in WAN1. Configured for PPPoE. Ive got configured a Port Forwarding on our SBS 2011 Server for OWA and other Services on web. I´ve got extreme Problems configuring VPN Connections. We use Quick VPN, other tools got to much buttons to click .
 
1st i configured a Group VPN , with FQDN (Remote Group) Local Group (IP only) . i configured 2 users. Then on a Laptop connected to the internet through an Hotspot Connection of an Iphone.
 
I entered the WAN IP .. Username. Password. Pressed ENTER. I get to the point of Verifyiing Network, and after it timeout with Remote Gateway not responding. Do you want to wait. If i Press Yes, after max. 1 minute there comes the message again.
 
I looked in the VPN Summary, and i see, that my username was connected through VPN for seconds, but then disconnected. Do i have overseen an option to configure??

View 4 Replies View Related

Cisco Routers :: RV042G Dual WAN Connections?

Jun 5, 2013

We are connecting to a Cisco DPC3825 cable modem supplied by our ISP.  It has been configured to act as a switch only.  They have supplied us with 2 static IP addresses.
 
When each WAN port is connected individually, everything is fine.  I see the IP addresses on the respective WAN port, and it is working fine.
 
When I connect both WAN ports to the modem at the same time, I see a large amount of traffic between the WAN ports, as indicated by the port LEDs, and the RV042G becomes completely non-responsive through its web interface.
 
How do I get the RV042G working with both WAN ports connected?

View 3 Replies View Related

Cisco Routers :: Upgrade From RV042 To RV042G

Mar 5, 2013

I'm about to upgrading our RV042 to RV042G since everything in the Network ist ready for Gigabit except the RV042
 
I think it's important to mention that another RV042, which is at a 2nd location, will remain for the VPN connection between the two locations. (Older Hardware are used at the 2nd location).
 
My Question is, are there any known issues, which should be cleared before changing the router.
 
Mainly issues with configuration migration and compatibility between RV042 and RV042G VPN connections.

View 3 Replies View Related

Cisco Routers :: Setup DMZ With RV042G And Single IP

May 11, 2013

I'm trying to set up a single web server in a DMZ using the RV042G and the docs seem woefully inadequate to explain how this is accomplished.
 
I've attach a picture of my setup..
 
I'm assigned a single Public IP.. in the example I've used 172.16.5.22 and so I've set the WAN interface for static IP.
 
The DMZ port is not obvious how to set up.. So I've chosen to define a private subnet and throw the web server in there. As I activate the DMZ, I specify a "subnet" and its address as 10.10.10.1, which I'm assuming goes to the DMZ/WAN port. I assign my webserver the address 10.10.10.3.
 
I leave the Access rules in their default condition.
 
I am a little unsure as to how to setup the static IP info for the web server.
 
Gateway:  10.10.10.1  ?
DNS:        10.10.10.1?  or 172.16.5.1? 

Problem #1
=========
My first problem is that the webserver cannot access the Internet. I get a timeout when I open the browser. I've tried every address there as the gateway and DNS..
 
Problem #2
========
If a person on the WAN side is attempting to connect to 172.16.5.22:80, how does the RV042G know to send it to the 10.10.10.3 device? It doesn't know what address the webserver is assigned; I just gave it a 10.10.10.1 address as the subnet address.
 
I think I'm missing something, conceptually here.
 
Can, in fact, you use the RV042G in this fashion with only a single public IP address? There is almost no information on how the router actually routes traffic when you choose either 'subnet' or 'range' (where the DMZ is in the same subnet as the WAN)

View 6 Replies View Related

Cisco Routers :: RV042G Set Up A VPN That Will Authenticate User Through AD

Apr 17, 2013

We looking into options for using VPN to allow users to work from home at our company. We already run Windows Active Directory and have a Cisco RV042G router. We would like to set up a VPN that will authenicate user through AD. Is this possible with the RV042G?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved