I've installed a rv042G, disabled dhcp, opened port 3389 (wan to lan), one port formwarding rule to terminal server.
Now 48 hours later, when i try to login to the router, (https), I'm automatticaly redirect to the https site of the NAS (iomega ix-200).
The nas is connected to a cisco sg100-24, which is connected to lan 1 on the router.
If you are using load balancing how do you bind i.e. all HTTPS traffic to i.e. wan1. RV042G V2 you can inter 0.0.0.0~0.0.0.0 as Source IP to forward from all IPs, how do you do that with a V3?
View 2 Replies View RelatedI have upgraded to the new RV042G to take advantage of the gigabit Ethernet speeds and to prepare for when our ISP upgrades our bandwidth. I currently use the RV042 with Protect Link enabled to filter out various categories from our network traffic. I noticed that this feature is not included with the RV042G.
Is this something Cisco will decide to add back in later? In the meantime, how to block content on the network? The basic URL and keyword filter will not meet our needs, since it is much easier to let a service such as Trend Micro manage what is blocked in the categories they offer.
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies View RelatedI have reconfigured the router from scratch using all sorts of methods and can not work out whats wrong, basically when the client is going to their bank the login screen takes upto a minute to load, and the same with hotmail. However using a cheap billion router these login screens are instant
Checking the CPU usage shows the CPU is hovering around 5-20% at the worst of timesThere is about 10 machines behind this router and they do not do that much intensive work over the link besides Outlook Anywhere (HTTPS)I have put a ACL on the LAN connection to only allow 1 machine in and still no luckI have also updated the IOS to c870-advipservicesk9-mz.124-24.T4.binAll other traffic runs fine over the link and there are no complaints on standard HTTP traffic
Never seen a Cisco, or any other L3 switch before. Nor an Lx router. Any step by step,or class room or web based training, or a partner or Cisco helper to get us up to speed on this.Goal is to limit http and https traffic in favor of telnet to an AIX server and RDP to a Windows TS. Printing would be ahead of http/s and below the others.
Interstingly, the web site promises 9 videos, but there are only 8. The demo guide says about OoS: "Coming Soon".Where to go? Who(m) to call?
I am having an ASA5510 with a CSC-SSM-10 module. I am able to block http traffic through the ASA but cannot block https traffic through it. Need to block https traffic using the CSC module.
View 19 Replies View RelatedI want to block some social networking sites using ASA 5510-CSC-SSM, As I searched and come to know that ASA 5510 can't inspect and intercept for https traffic because it is encrypted while traversing throught the ASA. I want the ASA to make functioning for https too, not only http. Can i perform this task by updating any software on existing device?
View 2 Replies View RelatedI am unable to redirect the HTTPS traffic on my cisco router with WCCP V2
View 2 Replies View RelatedRight now, in my network there is no proxy server and all users go straight through the ASA to access internet. I would like to put a squid with dansguardian (for web filtering). Steps in getting all http and https traffic from ASA go via my squid?
View 18 Replies View Relatedmy router (RV042G V01 Firmware Version : v4.2.1.02 ) get errors I can't understand.Lost connection, can't get a new IP, DNS does not work, total hangup.After a short time / reset everything works fine up to the next error.In the Log I found the following interest entries:undefined Kernel undefined Kernel failed (1).undefined Kernel Message from server.
View 1 Replies View RelatedI purchased RV042G and setup one-to-one NAT problem to several servers. ometimes the NAT servers lost the internet connection. My case as below
ISP provide two set Public IP Address , one modem
e.g.
set one) 100.100.1.2-6, gateway 100.100.1.1
set two) 200.200.2.2-6, gateway 200.200.2.1
[code]....
All computers and servers (one-to-one NAT) outbound and inbound all work fine. After several hours, only the servers (one-to-one NAT) alert internet connection broken, but the computers (non NAT) still have internet connection.
What's the problem occurs? Why only one-to-one NAT servers lost the connection? and Why only serveral hours later, the server lost the internet connection.
If I changed the WAN setting to same as subnet of the one-to-one NAT, it doesn't occur any problem.
I run my business network on the 192.168.x.x range with a server set as 192.168.2.4 statically. The router is currently connecetd to two DCHP wan connections from my ISP, I'm on a residential consumer plan. It has defaulted to loadblanacing with the second WAN however I want to have the second wan's public IP be used by my server and only the server however I wish for the server to still be on the lan so I can use HYPER-V's brided network connection feature to run VMs on the lan, and I would like their wan connection to be from wan 1... as for the entire lan except the server at 192.168.2.4 Is this possible, I can't seem to get the 1-to-1 NAT to do it?
View 4 Replies View RelatedWe have ASA 5520 with CSC-SSM 20 and we want to block https traffic but when we are blocking https traffic http traffic going to block but user are able to open website.
View 1 Replies View RelatedI have an ASA 5505 with the base license,When I setup the DMZ interface I had to add the deny access to the inside VLAN. The DMZ works fine with WiFi on it, but user's iPhones can't get email unless they turn WiFi off.Is there a simple way to allow HTTPS traffic through the DMZ interface to our internal Exchange server which is NAT'd on the 5505's external IP?
View 3 Replies View RelatedI have got a Cisco router connected to a LAN and to the internet.I was wondering if I could nat https traffic from inside to internet to a local server (Proxy) on a given port for example tcp 8080.
int tunnel0
ip address 192.168.0.1 255.255.255.0
ip nat inside
int fa0/1
des internet connexion
ip address 41.x.x.x.x 255.255.255.248
ip nat outside
ip access-list extended Proxy_Redirect
permit tcp 192.168.0.0 0.0.0.255 any eq 443
I have an ASA 5505 that I am using to connect my contractors to via an inside interface, the outside interface is my private LAN. I have setup on our corporate Proxy server to allow traffic from my outside interface of my ASA to go to the internet without credentials BUT log internet activity. The question is I want to know if the ASA can send that http & https traffic to my proxy server and all other traffic to my default route? I want to be able to send all internet traffic to my proxy server. This will avoid me asking the contractors to place proxy credentials in their browsers.
View 6 Replies View RelatedI am having a setup with a 2851 router & websense url filtering server where I need to forward the traffic to websense server for all the internet requests. The http traffic is getting filtered properly, but the https traffic is not getting filtered. The two commands I ahev given for http & http are as follows: ip inspect name test http urlfilter ip inspect name test https.
View 9 Replies View RelatedI've setup the RV042G with one ISP connection for now.I have my main PC running fine, but I have another PC hard lined to the router that had a connection after I power cycled the modem and router but now it no longer does. disabled the network on that PC, now I can't get it back at all.I have a wireless e2000 in one of the ports that I disabled the DCHP on and it seems to be running nicely.before I disabled the PC in question, aka port 3, it was showing as connected in the "192...." but now only as enabled.
View 1 Replies View RelatedIs there anyway to monitor netflow on RV042G. We have a network at a small school that will get bogged down during the day.
View 1 Replies View RelatedI have an issue with routing public IPs on the RV042G. I have been able to route the IP's in a couple of different ways, but there is always a nagging problem.
I have a PPPoE Business Class account with 5 routable public IP's. I would like to route the IPs and manage the private network using the RV042G.
Here is what I have tried and the problem that arose: 1) I used 1:1 NAT and the servers responded with no issue. This would be a workable config however I use Kerberos for single sign-on for my clients. To use this security protocol and bind the clients to the server, I must use a public IP on the server machines. In this scenario however, everything else worked fine. 2) I then tried using the DMZ and putting the servers on the DMZ port with a public IP entered in the network config of the machine. That even worked fine and I was excited until I noticed that the servers were reporting the public IP assigned to the DMZ port as their IP when they sent mail. I then ran a test and that is the case. The servers - each with a public IP - are reporting the IP of the DMZ port. I can't have that because the mail servers need to announce a correct IP so the reverse lookup will match. Once again, a little gnat gets in the soup.
Have a rv042g, newest firmware, trying to setup one to one nat on the configs page, I select enable, enter private ip , enter public ip, enter the range, and click "add to list" and nothing.... no error message, doesn't add to the list below it
View 1 Replies View RelatedI have RV042G dual WAN VPN router as a gateway in my small office. My ISP requires from me to connect through PPTP VPN to have access to the network. I've configured my router with static IP and every time I connect a laptop or desktop pc I need to connect to the VPN with the Windows VPN client.
View 3 Replies View RelatedWe have recently purchased a brand new RV042G VPN router, set it up, and had it running for a while without issues.
Now that we are actually trying to use the VPN functionality, the router becomes unstable after a while, showing "out of memory" lines in the logs, and after a day or two the VPN stops working completely and the web interface becomes completely inaccessible.
This issue happens when using any sort of VPN that's supported by the router.
I have created a protocol binding rule and even a bandwidth rule to make sure outgoing FTP needs to go through WAN2 interface. But it still goes through WAN1, it only works when I disconnect WAN1
View 13 Replies View RelatedI have a problem with the RV042G V01 router manufactured 12/2012.
After router settings the router works fine without any problems. After 10 or 12 hours I got the message that the side could not be opened, while no DNS. I checked inside the router and all settings looks ok DNS adresses from ISP are present on both WAN settings . When I use inside the router the funktion for DNS it will work but from any client is does not work. When I restart the router alls works fine. After few hours ( it's differnt 1,2 or 6 ) I have the same problem. No entry in the log's !
Recently setting up a RV042G for my SOHO. Everything seems to be fine except for SSL port forwarding. I know the router's external static IP is reachable because I test it out with remote management functionality from an external IP. Port forwarding also works correctly because I have other behind the router servers in both UDP and TCP working flawlessly. PPTP VPN also works corrrectly. What I can't get it to run is an Apache server. Looks to me RV042G kind of drop all SSL or HTTP ports from the WAN side.
Configuration:
- 4 port forward rule under "Setup/forwarding" for 80/8080/443 and 8443 all to the webserver with a static IP.
- Firewall page I have Firewall, SPI, DoS enabled.
- Added a firewall rules to allow all HTTP and HTTPS traffic from WAN1 to the webserver static IP.
- Toggle Block WAN Request, HTTPS and multicast does not affect the result.
- Toggle and mapping the remote management port to other port beside 443 does not affect the result.
The same setup will works corretly under my old Netgear FVS router. Am I missing something in RV042G setup?
I just got the RV042G today. I found the router can only accept 100000 Kbit/sec as bandwith, which is 100Mps only. According to the specification, it should have 1000Mps WAN. I have a internet link of 1000Mps, which is now limited by this router.
View 30 Replies View RelatedI'm trying to make an attached topology. This router should be attached to 2 different ISPs on both WAN interfaces (ISP1 with IP address - A.B.C.D, and ISP2 with IP W.X.Y.Z) and I want to use DMZ, too. My idea is to make a L2/L3 segmentation with 2 VLANs - Vlan RED for DMZ (private network 192.168.1.0/24) and vlan BLUE for Internal network (network 192.168.2.0/24). I checked in the manual that vlans are supported, but I can't see anything about 802.1q, can I use one trunk port or I should use 2 physical cables?
There should be inter-vlan routing and basic stateful firewall, so PCs in Vlan Blue should be able to initiate connections to DMZ servers, but the opposite should be denied. Router should make a port forwarding on its both WAN interfaces and forward incomming traffic (from Internet) to DMZ servers (with NAT). Both DMZ servers and internal PCs should have an internet access with NAT over both WAN uplinks.
Can I use RV042G for this setup and if not at all - are there any cisco SMB device which can do this?
How to configure an IPSec VPN with router RV042G.I need to know how to configure an IPSec VPN. Cisco Router with RV042G.
I spend this client your VPN parameters. [code]
i got a problem in configuring a VPN Connection for our Colleagues (Laptops & Iphones 4/4S/5) We got an RV042G .
A WAN Connection from Deutsche Telekom AG with Static IP connected in WAN1. Configured for PPPoE. Ive got configured a Port Forwarding on our SBS 2011 Server for OWA and other Services on web. I´ve got extreme Problems configuring VPN Connections. We use Quick VPN, other tools got to much buttons to click .
1st i configured a Group VPN , with FQDN (Remote Group) Local Group (IP only) . i configured 2 users. Then on a Laptop connected to the internet through an Hotspot Connection of an Iphone.
I entered the WAN IP .. Username. Password. Pressed ENTER. I get to the point of Verifyiing Network, and after it timeout with Remote Gateway not responding. Do you want to wait. If i Press Yes, after max. 1 minute there comes the message again.
I looked in the VPN Summary, and i see, that my username was connected through VPN for seconds, but then disconnected. Do i have overseen an option to configure??
We are connecting to a Cisco DPC3825 cable modem supplied by our ISP. It has been configured to act as a switch only. They have supplied us with 2 static IP addresses.
When each WAN port is connected individually, everything is fine. I see the IP addresses on the respective WAN port, and it is working fine.
When I connect both WAN ports to the modem at the same time, I see a large amount of traffic between the WAN ports, as indicated by the port LEDs, and the RV042G becomes completely non-responsive through its web interface.
How do I get the RV042G working with both WAN ports connected?
I'm about to upgrading our RV042 to RV042G since everything in the Network ist ready for Gigabit except the RV042
I think it's important to mention that another RV042, which is at a 2nd location, will remain for the VPN connection between the two locations. (Older Hardware are used at the 2nd location).
My Question is, are there any known issues, which should be cleared before changing the router.
Mainly issues with configuration migration and compatibility between RV042 and RV042G VPN connections.
