Cisco Routers :: How To Use SRP527W And Telstra Broadband USB Modem
Aug 4, 2012
Digital Business and my SRP527W router has just arrived. While I wait for my digital business to be activated i've got a small Eee PC shareing its internet connection through a D-link (piece of garbage) router into my server and out to my LAN.
What I would like to do is install the USB modem into the USB slot of my Cisco Router so i can finally get my data cabinet set up.
The problem is that the Telstra modem when being installed onto a computer, it requires a PIN to activate and then you are required to 'connect' via a little user interface.
Will this be an issue? Will i be able to connect my USB modem to my router while i wait for Digital Business to get going?
View 3 Replies
ADVERTISEMENT
Jul 14, 2011
The router recognizes the Sierra 312U modem but does not connect to Telstra. The modem is on a monthly plan (not pre-paid) and I have tried APN settings such as internet.telstra and internet.bigpond. The configuration is set to manual and the correct user id and password have been entered. explain the "daemon.err rc: start -1 port.... fail (-8)" in the log? 312U sierra model supposed to be compatible with SRP500s. Any other settings I should try?
Jul 13 17:59:09 SRP527W daemon.notice rc: 3G WAN is unplug
Jul 13 17:59:09 SRP527W daemon.notice rc: killall -TERM igmprt
Jul 13 17:59:10 SRP527W daemon.notice rc: igmprt -f -i br4080 -w 0 -c 5
Jul 13 17:59:12 SRP527W daemon.info 3G[354]: init 3G card phase get card info
Jul 13 17:59:13 SRP527W daemon.info 3G[354]: init 3G card phase verify pincode
[code]....
View 7 Replies
View Related
Feb 11, 2013
i have a telstra 4g wireless broadband stick. I was wondering ifi bought a TP-Link TL-WR841ND 300M Wireless N Router 2 Detachable Antennas would i be able to plug the stick into my computer and plug my computer into the router and make the router emit the broadband usb sticks interet?
View 2 Replies
View Related
Feb 28, 2012
! have a TELSTRA ADSL wireless router ( Thomson TG782T)I need to connect my 2 printers to it so I can operate them wirelessly to my laptop and Desktop computers
Laptop: TOSHIBA Satellite w/- windows 7 Professional
Desktop: ASI Computer w/- Windows 7 Ultimate currently connected to ADSL modem by yellow network cable.
View 1 Replies
View Related
Oct 4, 2011
We recently got the telstra tg782t wifi modem from bigpond. When we first got it, we were able to connect and use the wifi on our ipods. but recently we have been connecting to the modem but when i go on safari or app store it says that it cannot find the server.
View 3 Replies
View Related
Apr 17, 2013
if the SRP527W supports QOS over a site to site VPN.
SITE A will have the main phone system and SITE B will have a couple of phones which hook into the SITE A phone system over the existing IPSEC VPN
Need to be able to set some type of QOS over the VPN connection.
View 1 Replies
View Related
Feb 7, 2012
I have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
View 10 Replies
View Related
Mar 16, 2012
Is it possible to redirect all web traffic to a Symantec web filtering address on a particular listening port. I had a look at the Srp527w Router and can't find where this could be done.
View 1 Replies
View Related
Dec 17, 2012
I have a SRP527W router connected to a L2 managed switch (a TP-Link... I know, it is not a Cisco...). and a PC and a Printer connected to the switch. Now, I want to have the PC and the printer on 2 VLANs.
I've created 2 VLANs on the SRP (192.168.1.0/24 and 192.168.2.0/24) and I have assigned Lan port 1 to both. The SRP acts a DHCP server so I have the SRP setup as 192.168.1.1 and 192.168.2.1 providing IP addresses to the 2 VLANs.
I setup VLAN 1 and 2 on the switch, assigning port 2 to VLAN 1 and port 3 to VLAN 2 (port 1 is trunk and connects to the SRP).
When I fire up the PC and printer they get their respective VLANs correct addresses (PC: 192.168.1.30 and printer: 192.168.2.30) but I cannot for the love of Odin see the printer from the PC. The SRP has Inter VLAN routing enabled. By the way, the switch has address 192.168.1.2
View 8 Replies
View Related
Sep 12, 2012
I have a network which is based upon a 4507 Core/Dist switch, with 1G fibre to a bunch of radially connected 2960 Access switches. It all works fine and as expected for data and telephony.I have been tasked with setting up one of the VLANs to support multicast, so a bunch of video streams will be injected at the 4507, and will be delivered to client PCs connected to the 2960 switches.The 4507 is running with SVIs to some VLANs, but the VLAN that will have the Multicast on it is isolated, with no SVI.I could change this if required,I need to run IGMP snooping, and probably deploy CGMP to take advantage of the Cisco-proprietary functionaity.
View 4 Replies
View Related
Jun 5, 2012
I've got a new Cisco srp527w-u router which is working fine though it's syncing at a lower rate than my Billion (6mbps vs. 8.5 mbps for the billion on the same line). I had tweaked the billion way back to connect with a 4db SNR margin and almost certainly this is why it achieves the higher rate (by comparison the cisco is syncing with an snr margin of 12db). Is there some way that I can configure it to use a lower SNR margin? I realize this might reduce connection stability but I'd at least like to be able to give it a try if possible.
View 2 Replies
View Related
Jan 28, 2012
I recently bought a Cisco SRP527W and I'm trying to setup a second wireless network for guests.
I created a "guest" VLAN and I assigned the "guest" SSID which I have created.
I created a "guest" DHCP server and assigned it to the "guest" VLAN.
The "guest" SSID is set to broadcast and has WPA2 Personal (TKIP+AES) authentication. These are exactly the same settings I have for the "non-guest" WiFi.
However, I can't get my clients to connect to the network. The "guest" WiFi is visible and clients are prompted to enter the password but after that they end up with an APIPA address. When I move the "guest" SSID to VLAN1 (along with all the other networks) then it works absolutely fine.
I was just wondering if I'm simply missing something in the configuration ..
The device is running the latest firmware (1.01.24 (003) September 7, 2011)
DHCP server has DNS Proxy setting enabled and WAN Interface configured as "Default Route" (have basically replicated the same settings as VLAN1)
View 1 Replies
View Related
Apr 30, 2013
my client has just had the above router supplied by telstra and upon setup can no longer access filemaker server which was accessed prior on their netgear router. I have port forwarded to 5003 and 16000 as per the previous setup. Is there another setting somewhere that i am missing like perhaps static ip or something. I might add that networking is not my strong point.
View 7 Replies
View Related
Oct 21, 2012
I've just received a new SRP527W-U-E-K9 router to replace an old D-link router. However Apple IOS devices are not discoverable by iTunes on a Windows PC. The PC is connected to SRP527 by wired ethernet. All IOS devices are on the same SSID and the same VLAN as the wired ethernet devices.I have been reading on several other threads in this site about this exact same problem. The fault was that multicast broadcasts were not being forwarded between wired ethernet and WiFi on the same vlan. url...
The fault in thie above thread was resolved by a firmware update MR3 (v1.1.19) last year however it appears that the SRP527W-U has slightly different firmware to this version.The configuration of my SRP527 is the same as the original poster's config in the above thread. [code] The version information of my SRP is embedded below. As it is brand new, I assume that it is the most recent firmware, so I would have assumed that the bug which was resolved in the above thread above would be incorporated in this firmware version. [code] Is Cisco aware of this problem and is there any other firmware that I can load onto my model of SRP to resolve this?
View 1 Replies
View Related
Sep 16, 2012
I have a Cisco SRP527W at my remote office set up. I have configered a VPN connection to it. I installed Cisco VPN Client on my laptop.I can connect to the VPN but can not access the shared folders. I can ping the PC that has the shared folders. I take my PC and connect to the onsite LAN with WIFI, and I can now view the shared folders. I assume it must be somthing in the VPN set up that is blocking the shared folders from being seen. I also have disconnect all firewalls during testing at the remote end. I'am using windows 7 (64) on both PC's.
View 6 Replies
View Related
Jun 3, 2012
I've just purchased a SRP527w router and loaded the new firmware which includes the 5 client VPN server function.
The function works great with my iPhone as a client, but I've been unable to make a connection from my Windows 7 laptop, as the built in VPN configuration doesn't have anywhere to put the group name.
Is there a VPN client, or is there some way to get the Windows 7 native VPN configuration to work?
View 2 Replies
View Related
Nov 5, 2012
We have a SRP527W, we have created VLAN for DATA and VOICE remotly connected to an office by VPN.
VPN is working fine.
Now we want to register SIP lines integrated in SRP527W to a Cisco Call Manager located in our office.
The problem is that the source of SIP packets is WAN interface of the SRP527W, so packet wont pass in the VPN. Is possible to change the IP source of the SIP registration ? The most useful will be to set the IP source SIP on the voice VLAN.
View 2 Replies
View Related
Feb 12, 2012
I'm wanting to use the SRP527W (from Telstra) to route a block of assigned internet addresses (/29) over the WAN internet IP address. Is this possible on the 527W, or does it only do NAT routing?
View 6 Replies
View Related
Nov 26, 2012
I have a pair of SRP527W-U units, which each connect to a separate ISP by ADSL2+ . I am attempting to use each simultaneously as follows:
ISP-A via Cisco A for general traffic, and to run HTTP server X
ISP-B via Cisco B to run HTTP server Y
HTTP servers X and Y are on one machine, but binding to two separate IP addresses eg x.x.x.3 and x.x.x.4 . In a situation like this, I would normally configure Cisco A and Cisco B with x.x.x.1 and x.x.x.2 respectively. CiscoA would run DMZ to x.x.x.3 and Cisco B DMZ to x.x.x.4. The server would use x.x.x.1 as the default route. Then I would set Cisco A to have a policy route catching source address x.x.x.4 and sending it to next-hop/gateway x.x.x.2.
BUT, the policy route feature requires traffic be sent out the WAN port or a tunnel (no next hop, only WAN side VLANs, tunnels or interfaces). configuring a GRE tunnel connecting the two routers is fruitless, and the tunnels refuse to be created on the LAN side (tunneling is only possible out the WAN).
Attempting to simultaneously use the 4th LAN/WAN port in WAN mode also fails, as the WAN port is only available when the ADSL port is not. Under Win2000 and Linux it was possible to configure two separate network cards and use seperate sub nets, each with a default route. This feature no longer works with more recent versions of Windows.
How I might get this working, without buying a 887? I am open to buying a 547.
View 1 Replies
View Related
Mar 20, 2012
Currently we're using Cisco 867 routers, wich connect to a IP-VPN network with internal IP's. I'm trying to test a SRP527W router as a replacement for the current 867 routers, as they are more affordable for our customers in the SMB segment.
However all our 867 routers have 'ip unnumbered' on their dialer interfaces (we're using PPPoA) to avoid NAT and problems with SIP and easy management of the IP Phones behind the router.
Does any know if it is possible to have the same IP on the WAN interface and the LAN interface? If so, how do you configure it in the SRP527W?
View 1 Replies
View Related
Apr 17, 2013
I upgraded the firmware to latest and apparently i've lost couple of options inlcuding TCP Dump in diagnostic as well as I cannot find how to disable/enable an ethernet port.
View 5 Replies
View Related
Feb 2, 2013
I have recently purchased a srp527w and I am thinking to buy a Cisco wireless ip phone 7921g. Does it works with the srp527? Do I need another device betweenn my srp527 and the ip phone? or it just works by configuring the voice vlan. If so, what phone would it work, the analog or the ip phone?
View 2 Replies
View Related
Aug 20, 2011
having trouble to configure the Cisco SRP527w where we have two incoming VLAN's.
1. vlan1 is for internet (20mbps)
2. vlan2 is for a specific application (Specific IP Address - 10mbps)
Somehow we are unable to configure the router to enable PC's connected to the router to access both vlan based to the application specific vlan. Its always routing it through the internet.
View 0 Replies
View Related
Sep 16, 2010
im having trouble setting up site to site vpn from my 527w to my 877 series and thought it would be much easier to see whats going on the 527 if i could see command line
so ive ssh'd to the 527s ip address but none of the usernames/password combos work that let me in the web gui, what are the logins?
View 9 Replies
View Related
Feb 14, 2011
I've been having the lockup issue with the SRP527W (in fact this has been an extremely embarrassing situation after spending 4 x what I could have on a Net gear type unit, to do the same task). I've not yet managed to get hold of the new firmware (MR3) as I've not received the email with a link.
On another note, I'm not sure if this has been covered in other posts, but, when my unit stops working (Wireless still alive, no internet) - the CPU hits and stays at 100% and only a reboot fixes it.
View 5 Replies
View Related
Sep 20, 2012
I just bought a new Cisco SRP527w and I'm just new on this kind of equipment. I can't locate the user management tab as I'm trying to change the default password.Also, I can't access the internet. My dsl modem rj45 is connected to the WAN/LAN port with IP Static settings.
View 14 Replies
View Related
Jun 12, 2012
I'm trying to configure the newly install Cisco Small Business router SRP527W. This router is provide by one of Malaysia ISP
Problem I found is that, when a user (me) login to the router via web access, than I request my colleague (B), to test the feature I set to the router and try to login to the router via web access at his laptop.
Suprise, suprise, user B redirect to the basic setup page with Admin privilege without enter username and password. By upgrade latest firmware still unable to solve it.
View 1 Replies
View Related
Jun 21, 2012
I have a SRP527W what has a constantly flashing power LED.Is there anything that I can do to attempt to recover this router?
View 2 Replies
View Related
Mar 25, 2012
I am having trouble setting nat rules on device SRP527W-U with the latest firmware 1.2.4 (003). The latest firmware 1.2.4 has introduced the possibility to create specific nat rules via "ACL policy rules". I am trying to use this "new feature" not available in the older releases to get my network configuration done. The configuration I would like to do is to have two different vlan. In the vlan1 I would like to nat the PCs via the point_to_point interface and in the vlan2 I don't want use nat feature so each computer will be reachable via public ip address. I have configured two different PVCs on the device.
View 2 Replies
View Related
Mar 2, 2013
I am a real amateur here. I have configured a cisco VPN server, group and user on an SRP527W, ADSL2+ AnnexA, 802.11n ETSI, 2FXS/1FXO. I can connect from my PC with the Cicso VPN client on it (I get the banner) but I cannot ping into the local network at all. Once I do get in I will be using shares to work on files or VNC to take over a CAD workstation.I am sure I just have not set up something but I don't know where to look. My local network is 192.168.15.***
View 11 Replies
View Related
Feb 23, 2012
I have a problem to configure my connection SDSL.my router is SRP527W. my modem is Patton 3088. Do I need to update the ios? or there is a specific configuration of static IP ?
View 1 Replies
View Related
Jan 11, 2012
I bought a new cisco srp527w (K9-G4) and all seems fine but when I reboot it the date resets to 1970/1/1I upgraded it from vrs 1.01.09(001) to 1.01.24 but it is still doing it.I havent yet got it onto the internet as it wont be going live until it goes into a client site, so I cannot set it to NTP to see if this will work around the problem of setting the date and time manually.
View 2 Replies
View Related
Nov 30, 2011
We have a SRP527W with 1.1.24 firmware.
We have DHCP disabled and have assigned a IP address of 10.65.73.254 on the Interface Setup/Lan/VLAN Settings/data_lan.
When I configure a client to use 10.65.73.254 as its DNS server it cannot resolve hostnames eg [URL]. Obviously I have 10.65.73.254 as the default gateway on the client and it can ping the external host via IP Address so it only appears to be the modems function as a DNS Server that is not working.
From the diagnostics ping I can put in [URL] and it resolved and works, so the modem is correctly getting it's DNS Settings from the ISP
View 2 Replies
View Related
