Cisco :: Run The Int Range Command
Oct 1, 2012I am trying to run the int range command and i am getting this error
View 19 Replies
ADVERTISEMENT
Cisco LAN :: 3750 - Range Command / Session Hang
Oct 18, 2012I've noticed that when using the range command to configure multiple interfaces on a 3750 the SSH session oftens hangs. It's seems the more interfaces in the range command the more often it hangs. I have a feeling it also spikes up the CPU. Doesn't seem to be related to a specific version of code.
View 6 Replies View RelatedCisco WAN :: What Is The Equivalent Command On IOS-XR 4.3.0
Jan 10, 2013I want to configure this:
ip vrf TEST
rd 65500:1
route-target export 65500:1
route-target import 65500:1
bgp next-hop Loopback500
on IOS-XR 4.3.0
What is the equivalent command on IOS-XR?
route-policy TEST1
set next-hop 1.1.1.1
vrf TEST
address-family ipv4 unicast
import route-policy TEST1
Cisco WAN :: Source CPU Command Not In 15.x?
Sep 23, 2012why the command "source cpu rp" has been removed from IOS15.0(1)SY1. I can succesfully configure the following ERSPAN on 12.2 SXJ3 but not on ios 15.x. Did not understand why cisco has descoped this command.
monitor session 10 type erspan-source
shutdown
source cpu rp rx (--- 15.0 has no such option on 6500 )
destination
[code]....
Cisco WAN :: 887 Command Change
Mar 15, 2011I have recently up swapped out an 877 router for an 887 router and have copied the config template accross however it will not take 3 of my commands.
AAA accounting system default stop-mly group tacas+
ip inspect name firewall cuseeme timeout 3600
dsl operating -mode auto
Cisco :: NAT To External IP - Range 71.1.1.1 /25 (outside)?
Jun 5, 2011I have internal Network (inside)
192.168.1.1
192.168.1.2
192.168.1.3
192.168.1.19
192.168.1.89
And I want it to nat to external ip --- range 71.1.1.1 /25 (outside)
71.1.1.1
71.1.1.2
71.1.1.3
71.1.1.4
71.1.1.5
Q1) What is the best way to nat it on the asa b]
static (inside,outside) 71.1.1.1 192.168.1.1 netmask 255.255.255.255
static (inside,outside) 71.1.1.2 192.168.1.2 netmask 255.255.255.255
static (inside,outside) 71.1.1.89 192.168.1.3 netmask 255.255.255.255
or
Q2) should i do like this
static (outside, inside) 192.168.1.0 71.1.1.0 netmask 255.255.255.128
Q3)which interface should I apply ?
[b]Q4) What is the difference between :
static (inside,outside) 71.1.1.1 192.168.1.1 netmask 255.255.255.255
and static (outside, inside) 192.168.1.1 71.1.1.1 netmask 255.255.255.255
Cisco :: ASA5510 Why ASA Doesn't Have Right Command
May 8, 2012I would like to implement a zone based firewall on my ASA5510. Is ZBF possible on ASA? or is it strictly for routers? I know we've implementd ZBF using Sonicwall firewalls before. A little confused here as to why my ASA doesnt have the right commands.Maybe my version of ASA software is too old? It's 8.2 if i remember right.
View 11 Replies View RelatedCisco :: Testing ACL With Ping Command?
Sep 11, 2012why using ping to test the functionality of an ACL could proove insufficient?
View 9 Replies View RelatedCisco :: 6509 / EEM Command To Read OID Value?
Feb 2, 2012I am trying to change SNMPv2 community string on 6509 remotely, without using expect script. I tried EEM applet (we cannot use TCL scripts), but it does not work. EEM command "action 10 info snmp oid 1.3.6.1.2.1.1.4 get-type exact" is supposed to store the result into an environment variable. It does not. Or at least not in the one that is documented. Is it a bug? We have IOS 12.2(17r)SX5. To get EEM version i ran "sh event manager version" and got "eem: (v240_throttle) 2.21.32". Does it mean i have EEM version 2.21?
View 6 Replies View RelatedCisco WAN :: GNS3 Track 1 IP SLA Command Not Available
Dec 20, 2011I was just brushing up few things in GNS3 and after setting up an SLA.Now when I want to set the track ip I get not option for sla why??I am running c3725-adventerprisek9-mz.124-15.T5 shouldn't it be available?
View 2 Replies View RelatedCisco :: LMS 4.2 Apply One Command To All Devices
Nov 29, 2012how to apply one command "wr" to all my Cisco Devices Managed by LMS 4.2?
View 2 Replies View RelatedCisco WAN :: 2951 With IOS 15.0 No Voice Command
May 30, 2011We recently purchased the Cisco Router 2951 router with the IOS 15.0. I have tried to put in my VIC2-4FXO card in it. When I did show invetery, it detected the card.[code] When I tried to configure the voice port by typing voice port, it shows % Invalid input detected at '^' marker. I have tried to reset the cad and replace with another one.
View 3 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.1 / This Command Is Not Authorized
Feb 5, 2013We have an issue with ACS server 5.1.0.44.X. We want make a one user with few commands: show ip route static-table(deny other show commands)configure terminal, terminal length 0 ip route (with all possible arguments). All works fine except ip route command, when i try to type it I see - "This command is not authorized".
View 1 Replies View RelatedCisco WAN :: 2901 / The Reachability Command Is Not Available
Jan 27, 2013I have recently bought cisco 2901 in order to replace it with our 1811W that we have at the moment.When I try to set a failover / backup with rtr; it seems like the function is not valid.Once I select rtr and set the object #, the reachability command is not available.Does that mean this function is not a part from the license package I have?
View 6 Replies View RelatedCisco Firewall :: NAT Command Conversion PIX 6.3 To ASA 8.4(2)
Dec 28, 2011I am in the process of migrating a production firewall from PIX 6.3 to ASA 8.4(2). This is going to be a complete firewall rebuild and I will not be upgrading the configs because they have become out of date and very bloated. I am in the process of converting the NAT commands.[code] I am hoping these commands would be enough to replicate the previous functionality. I removed all the static identity NATs because NAT control is no longer in place so those rules are not required. Additionally I didn't re-create the rules that had NAT ID 0 or 1 because it didn't look like they were doing anything. correct way to do the static NAT commands at the bottom.
View 3 Replies View RelatedCisco AAA/Identity/Nac :: (command Set) Not Working In ACS 5.3?
Mar 4, 2013I have to created command set under "Policy Elements>Authorization and Permissions>Device Administration" for limited access user in ACS 5.3. Like i triyed to give them permission to only few show commands. I have set user priviledge 1, 7, 10 however either of the priviledge level user was able to run those commands. I works like the shell priviledge level.
View 1 Replies View RelatedCisco Firewall :: ASA 8.4 NAT Command Selection
Jul 4, 2011I am designing a new NAT configuration for an ASA 8.4
On my PIX 8.0 configuration I needed to allow bidirectional traffic between interfaces with different security levels. For example, Inside at 100 and dmz at 50.To accomplish this in 8.0 I used a static NAT command along with any necessary ACLs.
I now need to apply this same 8.0 config for 8.4. With the static command not availablein 8.4 I am unsure of which NAT commands to use to achieve the bidirectional traffic.
Cisco WAN :: MLS QoS Map Command Missing On 2801
Oct 31, 2012I am trying to run the following commands on a 2801 router, but the commands are missing:
mls qos
mls qos map cos-dscp 0 8 16 40 32 46 48 56
The only QoS command i have in global config is (no MLS qos) :
REMOTE-ROUTER1(config)#qos ?
restore-show-output Restore old show output
shape-timer Set the HQF shape timer interval
The router is running IOS:
System image file is "flash:c2801-ipbasek9-mz.151-4.M5.bin"
Am i just running the incorrect IOS or am i missing somehting, i need to change the QoS Map for my Nortel VoIP. The VoIP phones connect to a 3750 PoE which used to conenct to a 2651XM to route VoIP and data traffic over the same copper pairs (WAN link to hub site) hence the need for a Service policy but being Nortel phones, require changing the cos-dscp map. the 2801 is going to replace the 2651XM using a new HWIC.
Cisco AAA/Identity/Nac :: What Is Command To Launch GUI On ACS 5.x
Mar 10, 2013After logging in to the ACS, what is the command to launch the GUI on a Cisco ACS 5.x.
View 1 Replies View RelatedCisco Firewall :: What New Command Is For NAT In Version 8.3
May 29, 2013what the new command is for NAT in version 8.3?The config i have is from Version 7.2 and doesnt work on 8.3. [code]
View 12 Replies View RelatedCisco AAA/Identity/Nac :: Setup A Command Set In ACS 5.3?
Nov 26, 2012I'm trying to set up a command set in Cisco ACS 5.3, I can't get i to work no mather who I try What I'm trying to accomplish is that some users, say Bob can run every priv. level 1 command + show run, or just to specify which commands Bob will be able to run, whatever is easiest to set up.
In my switch I have the commands:
aaa new-model
aaa authentication login default group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authorization config-commands
aaa authorization commands 1 default group tacacs+
aaa authorization commands 15 default group tacacs+ <--- tried diffrent apporaches whith priv level..
(and specied a tacacs server)
is the "default" under "aaa authorization commands 1x default group tacacs+" the name of the command set?
In the ACS I have specied a Authorization group and binded it to the command set, should the user have priv 15 for this to work or priv 1?(I have also specied a user and an identity group and specied ip ranges under "Network Devices and AAA Clients")
Cisco WAN :: SNTP No Such Command On C1941?
Apr 24, 2011I have two C1941.The first C1941 does not support SNTP but the second C1941 supports SNTP. The only difference which I can spot is their license. The first C1941 does not have security license but the second C1941 has. What is the URL that has info on what IOS commands are supported on IPbase license, sec license..etc
First C1941
C1941_1(config)#do sh ver Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)Technical
[Code].....
Cisco AAA/Identity/Nac :: ACS 5.2 - Command Set Is Empty
Jan 15, 2012I have a problem with the ACS 5.2 configuration: I am trying to use the AAA authorization to centralize privileges and commands but only the privilege level is sent to router, the command set aren't sent.
The test cenary is this:
ACS 5.2Router 2900 family IOS 15.0
The ACS is configured with:
Shell Profiles (to match with a privilege level), Command Sets (with the command list), Service Selection Rules (to set to one service) and Authorization (to assign one shell profile and one command set).
The router is configured with the follows commands:
[code]....
Cisco Security :: Command Set Authorization In ACS 5.0
Jan 6, 2011Attached is what i have done for command authorization for privilege level user 2
View 27 Replies View RelatedCisco WAN :: 7606 - Tftpdnld Command Not Available
Jul 19, 2011I have a 7606 router with sup 720-3bxl. IOS has been crashed recently and i can use only Roman mode now. Ive tried to upload ios image using tftp server but the command tftpdnld id not available in this router. I don't know why. Then i tried to boot from flash disk but finally it also shows an error like
System received a Software forced crash signal= 0x17, code= 0x24, context= 0x42359674 PC = 0x402d248c, Cause = 0x1020, Status Reg = 0x34008002
How to make the router in running condition.
Cisco :: Air LAP-1042N - Command Did Not Work
Dec 20, 2012 I just purchase Cisco LAP-1042N for my office network expansion. When i console into the AP via serial. I am not able to used "configure terminal" command to set my AP name,static IP address.
I tried using "debug lwapp console cli" command it did not work. below is the capture screen of the error i am getting when assigning AP hostname. Error message : command is disable.
Cisco Firewall :: 5505 - Command Changes From 7.2 To 8.6
Mar 10, 2013I'm coming from a 5505/5510 ASA to a 5512x. I see the following 7.2 commands are now set with the NAT command in 8.6:
-------------begin 7.2 commands---------------------
global (outside) 1 interfaceglobal (inside) 10 interfaceglobal (wireless) 1 interfacenat (inside) 0 access-list nonatnat (inside) 1 192.168.3.0 255.255.255.0static (inside,outside) tcp interface www 192.168.3.114 www netmask 255.255.255.255static (inside,outside) udp interface 5008 192.168.3.117 5008 netmask 255.255.255.255static (inside,outside) tcp interface 3390 192.168.3.101 3389 netmask 255.255.255.255static (inside,outside) tcp interface h323 192.168.3.118 h323 netmask 255.255.255.255
--------------end 7.2 commands----------------------
What Is The Command Switch
May 28, 2012What is the command switch (the letter/s that you use withsign after the command) that can be used for displaying the per protocol statistics with the above command
View 1 Replies View RelatedCisco :: Allowing IP Range Of 2 Hosts Through PIX?
Jan 30, 2012I'm new to this site, fully Microsoft certified but only just getting in cisco and looking to pass my CCNA later this year. Actual commands and general use on Cisco's im quite good at but general networking knowledge on networking (subnetting and network layers) I kinda suck at so will be studying a lot on this side of things[CODE]
View 5 Replies View RelatedCisco VPN :: 172.16.x.x / 16 / Setup VPN But Both Side Use Same IP Range?
Sep 26, 2011We need to setup a VPn to another company, but we both use 172.16.x.x/16. Would I need to get both sides to setup a VPn using 2 different subnet ranges and then get us to NAT it to our own range?I was thinking of making our side 10.7.x.x/16 and their side 10.6.x.x/16
View 1 Replies View RelatedCisco WAN :: L2TPV3 Tunnel Id Range Different On IOS 12.2(33)SRE / 12.4(15)T
Jan 18, 2011I was found the different IOS support L2TPV3 tunnel ID, like 12.2(33)SRE is support 32bit, 12.4(15)T is support 16bit.so the 12.2(33)SRE can't xconnect/l2tpv3 to 12.4(15)T.
I found the 12.2(33)SRE Local Tunnel ID is over 65535, how about reduce it less 65535? or some other suggest to xconnect/l2tpv3 on different IOS?bcoz using same IOS series is normal. like 12.4T and 12.4T / 12.2SRE and 12.2SRE
some result is following.
12.4(15)T:
xxxx#sh xconnect interface gigabitEthernet 0/2.209 detailLegend: XC ST=Xconnect State, S1=Segment1 State, S2=Segment2 StateUP=Up, DN=Down, AD=Admin Down, IA=Inactive, NH=No HardwareXC ST Segment 1 S1 Segment 2 S2------+---------------------------------+--+---------------------------------+--DN ac Gi0/2.209 209(Eth VLAN) UP l2tp 152.xxx.xxx.120:500 DN Interworking: none Session ID: 15758 Tunnel ID: 60524 Protocol State: DOWN Remote Circuit State: DOWN pw-class: vlan-xconnect
xxxx#sh l2tun tun
[code]....
Cisco WAN :: 2851 - Mid-range Router
Jan 23, 2013Is the 2851 router meet these requirements ? if no. What is the must specific series of the routers suitable for this requirement:
1. Comprehensive interface range supporting T1/E1, NxT1/E1, FE, and High-Speed WAN .
2. Wide array of Layer 2 access protocols including Frame Relay, Ethernet, and PPP/HDLC .
3. Rich and granular QOS and instrumentation for prioritizing mission-critical traffic such as voice .
4. A modular platform with a broad range of interface options.
5. Network Address Translation (NAT), and IP Sec .
6. Four (4) auto sensing LAN Ports (10/100/1000) Mbps built-in routed ports.
7. WAN Interface Slots (4-6 option Slots) .
8. WAN Interface Modules (2xT1/2xE1/2xSerial/2xFE/DS3).
9. Memory (512/1024 MB DRAM) .
10. Built in redundancy (Power Supply) .
11. Two (2) Integrated GE ports with copper and fiber support .
12. Support for a Small form-Factor Plugged ( SFP) port for GE.
13. Support Network Timing Protocol (NTP).
14. Security: On-board encryption Support of up to 2500 VPN tunnels with the AIM-HPII-PLUS Module Antivirus defense support through Network Admission Control (NAC) many more essential security features .
15. Voice : Optional support for Survivable Remote Site Telephony support for local call processing in small enterprise branch offices for up to 240 IP phones.
16. Performance : Up to 1GB DRAM Up to 1GB Flash The maximum transmission unit (MTU) Up to 9576 bytes Throughput up to 1.2 Gbit/s .
17. 110/220 volts.
18. Warranty certified by Sis 98 or by OEM (original equipment manufacturer) .
19. Up to 115.2 Kbps for Console/Aux port with DDR capability.
20. Supports IPv6
IP Address Range Different To What It Should Be
Jul 9, 2012we had servers with 10. addresses and they now give out 192. addys when pinged. The addresses haven't been changed manually but what might cause this?
View 1 Replies View Related