Cisco WAN :: SNTP No Such Command On C1941?
Apr 24, 2011
I have two C1941.The first C1941 does not support SNTP but the second C1941 supports SNTP. The only difference which I can spot is their license. The first C1941 does not have security license but the second C1941 has. What is the URL that has info on what IOS commands are supported on IPbase license, sec license..etc
First C1941
C1941_1(config)#do sh ver Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)Technical
[Code].....
View 5 Replies
ADVERTISEMENT
Feb 13, 2013
I received an SG300-MP as an RMA replacement for a Linksys SRW2008MP and I can't seem to get the SNTP to work.Previously on other devices I have only had to set the SNTP server name or IP address and that was it. So some of the options of the SG300 are foreign to me.So I first set
Administration > Time Settings > System Time > Main Clock Source (SNTP Servers) [X]
Then I set several SNTP server IP addresses
Administration > Time Settings > SNTP Unicast
SNTP Client Unicast [X] Enable
> Add
Other / 64.147.116.229 (nist1-la.ustiming.org)
Other / 24.56.178.140 (wwv.nist.gov)
Other / 128.138.141.172 (utcnist2.colorado.edu)
Other / 129.6.15.29 (time-b.nist.gov)
Some servers I set "Poll Interval" and some I didn't because I wasn't sure what this does.The status for all servers indicate "Down" with 31.12.1899 0.0.0 for the "Last Response"/I found those IP addresses via [URL] Also the setting
Administration > Time Settings > System Time SNTP Multicast / Anycast
I have disabled, and I don't know what this does either...
View 5 Replies
View Related
Jan 13, 2013
I had connected a computer and NTP to the SG500. i had successfullly sync the internet time on the computer. but when i type 'show clock' on the terminal. The switch did not manage to sync the ntp time.
clock timezone sg +8
clock source sntp
sntp unicast client enable
sntp server 192.168.4.36
View 3 Replies
View Related
Aug 16, 2011
I want to configure IOS SSL VPN on C1941 Router. let me know if any additional License is required for that.
View 1 Replies
View Related
Aug 5, 2012
i have Cisco 1941 router with following IOS image:Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M5, RELEASE SOFTWARE (fc2) below mentioned commands are not working :
crypto isakmp policy 5
encr aes 256
authentication pre-share
group 2
what could the issue ? do i need to change the IOS image.
View 6 Replies
View Related
Mar 14, 2013
1) KA-AGR-DEP-C1941#telnet 74.125.236.133 /source-interface gigabitEthernet 0/1
% telnet connections not permitted from this terminal
How can we enable telnet for the above for testing
2) KA-AGR-DEP-C1941#sh caller
Active Idle
Line User Service Time Time
vty 132 agri VTY 00:02:24 00:00:00
Here we are getting the time of our vty login and not the serial link uptime. How can we enable to check the serial link uptime.
3) CGHSULSOR#traceroute google.com
Translating "google.com"...domain server (164.100.3.1) [OK]
Type escape sequence to abort.
Tracing the route to google.com (74.125.236.129)
1 10.161.20.69 4 msec 4 msec 4 msec
2 10.255.232.38 4 msec 4 msec 4 msec
3 10.255.238.237 40 msec 40 msec 40 msec
4 10.255.221.225 40 msec 40 msec 40 msec
5 * *
CGHSULSOR#telnet 74.125.236.129 80
Trying 74.125.236.129, 80 ...
% Connection refused by remote host
In the above case it's showing refused by remote host. If the port 80 is opened in firewall also if we get this error what will be the issue. As i understood when firewall port is opened we wil get as OPEN
View 4 Replies
View Related
Oct 1, 2012
I am trying to run the int range command and i am getting this error
View 19 Replies
View Related
Jan 10, 2013
I want to configure this:
ip vrf TEST
rd 65500:1
route-target export 65500:1
route-target import 65500:1
bgp next-hop Loopback500
on IOS-XR 4.3.0
What is the equivalent command on IOS-XR?
route-policy TEST1
set next-hop 1.1.1.1
vrf TEST
address-family ipv4 unicast
import route-policy TEST1
View 1 Replies
View Related
Sep 23, 2012
why the command "source cpu rp" has been removed from IOS15.0(1)SY1. I can succesfully configure the following ERSPAN on 12.2 SXJ3 but not on ios 15.x. Did not understand why cisco has descoped this command.
monitor session 10 type erspan-source
shutdown
source cpu rp rx (--- 15.0 has no such option on 6500 )
destination
[code]....
View 2 Replies
View Related
Mar 15, 2011
I have recently up swapped out an 877 router for an 887 router and have copied the config template accross however it will not take 3 of my commands.
AAA accounting system default stop-mly group tacas+
ip inspect name firewall cuseeme timeout 3600
dsl operating -mode auto
View 2 Replies
View Related
May 8, 2012
I would like to implement a zone based firewall on my ASA5510. Is ZBF possible on ASA? or is it strictly for routers? I know we've implementd ZBF using Sonicwall firewalls before. A little confused here as to why my ASA doesnt have the right commands.Maybe my version of ASA software is too old? It's 8.2 if i remember right.
View 11 Replies
View Related
Sep 11, 2012
why using ping to test the functionality of an ACL could proove insufficient?
View 9 Replies
View Related
Feb 2, 2012
I am trying to change SNMPv2 community string on 6509 remotely, without using expect script. I tried EEM applet (we cannot use TCL scripts), but it does not work. EEM command "action 10 info snmp oid 1.3.6.1.2.1.1.4 get-type exact" is supposed to store the result into an environment variable. It does not. Or at least not in the one that is documented. Is it a bug? We have IOS 12.2(17r)SX5. To get EEM version i ran "sh event manager version" and got "eem: (v240_throttle) 2.21.32". Does it mean i have EEM version 2.21?
View 6 Replies
View Related
Dec 20, 2011
I was just brushing up few things in GNS3 and after setting up an SLA.Now when I want to set the track ip I get not option for sla why??I am running c3725-adventerprisek9-mz.124-15.T5 shouldn't it be available?
View 2 Replies
View Related
Nov 29, 2012
how to apply one command "wr" to all my Cisco Devices Managed by LMS 4.2?
View 2 Replies
View Related
May 30, 2011
We recently purchased the Cisco Router 2951 router with the IOS 15.0. I have tried to put in my VIC2-4FXO card in it. When I did show invetery, it detected the card.[code] When I tried to configure the voice port by typing voice port, it shows % Invalid input detected at '^' marker. I have tried to reset the cad and replace with another one.
View 3 Replies
View Related
Feb 5, 2013
We have an issue with ACS server 5.1.0.44.X. We want make a one user with few commands: show ip route static-table(deny other show commands)configure terminal, terminal length 0 ip route (with all possible arguments). All works fine except ip route command, when i try to type it I see - "This command is not authorized".
View 1 Replies
View Related
Jan 27, 2013
I have recently bought cisco 2901 in order to replace it with our 1811W that we have at the moment.When I try to set a failover / backup with rtr; it seems like the function is not valid.Once I select rtr and set the object #, the reachability command is not available.Does that mean this function is not a part from the license package I have?
View 6 Replies
View Related
Dec 28, 2011
I am in the process of migrating a production firewall from PIX 6.3 to ASA 8.4(2). This is going to be a complete firewall rebuild and I will not be upgrading the configs because they have become out of date and very bloated. I am in the process of converting the NAT commands.[code] I am hoping these commands would be enough to replicate the previous functionality. I removed all the static identity NATs because NAT control is no longer in place so those rules are not required. Additionally I didn't re-create the rules that had NAT ID 0 or 1 because it didn't look like they were doing anything. correct way to do the static NAT commands at the bottom.
View 3 Replies
View Related
Mar 4, 2013
I have to created command set under "Policy Elements>Authorization and Permissions>Device Administration" for limited access user in ACS 5.3. Like i triyed to give them permission to only few show commands. I have set user priviledge 1, 7, 10 however either of the priviledge level user was able to run those commands. I works like the shell priviledge level.
View 1 Replies
View Related
Jul 4, 2011
I am designing a new NAT configuration for an ASA 8.4
On my PIX 8.0 configuration I needed to allow bidirectional traffic between interfaces with different security levels. For example, Inside at 100 and dmz at 50.To accomplish this in 8.0 I used a static NAT command along with any necessary ACLs.
I now need to apply this same 8.0 config for 8.4. With the static command not availablein 8.4 I am unsure of which NAT commands to use to achieve the bidirectional traffic.
View 1 Replies
View Related
Oct 31, 2012
I am trying to run the following commands on a 2801 router, but the commands are missing:
mls qos
mls qos map cos-dscp 0 8 16 40 32 46 48 56
The only QoS command i have in global config is (no MLS qos) :
REMOTE-ROUTER1(config)#qos ?
restore-show-output Restore old show output
shape-timer Set the HQF shape timer interval
The router is running IOS:
System image file is "flash:c2801-ipbasek9-mz.151-4.M5.bin"
Am i just running the incorrect IOS or am i missing somehting, i need to change the QoS Map for my Nortel VoIP. The VoIP phones connect to a 3750 PoE which used to conenct to a 2651XM to route VoIP and data traffic over the same copper pairs (WAN link to hub site) hence the need for a Service policy but being Nortel phones, require changing the cos-dscp map. the 2801 is going to replace the 2651XM using a new HWIC.
View 4 Replies
View Related
Mar 10, 2013
After logging in to the ACS, what is the command to launch the GUI on a Cisco ACS 5.x.
View 1 Replies
View Related
May 29, 2013
what the new command is for NAT in version 8.3?The config i have is from Version 7.2 and doesnt work on 8.3. [code]
View 12 Replies
View Related
Nov 26, 2012
I'm trying to set up a command set in Cisco ACS 5.3, I can't get i to work no mather who I try What I'm trying to accomplish is that some users, say Bob can run every priv. level 1 command + show run, or just to specify which commands Bob will be able to run, whatever is easiest to set up.
In my switch I have the commands:
aaa new-model
aaa authentication login default group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authorization config-commands
aaa authorization commands 1 default group tacacs+
aaa authorization commands 15 default group tacacs+ <--- tried diffrent apporaches whith priv level..
(and specied a tacacs server)
is the "default" under "aaa authorization commands 1x default group tacacs+" the name of the command set?
In the ACS I have specied a Authorization group and binded it to the command set, should the user have priv 15 for this to work or priv 1?(I have also specied a user and an identity group and specied ip ranges under "Network Devices and AAA Clients")
View 2 Replies
View Related
Jan 15, 2012
I have a problem with the ACS 5.2 configuration: I am trying to use the AAA authorization to centralize privileges and commands but only the privilege level is sent to router, the command set aren't sent.
The test cenary is this:
ACS 5.2Router 2900 family IOS 15.0
The ACS is configured with:
Shell Profiles (to match with a privilege level), Command Sets (with the command list), Service Selection Rules (to set to one service) and Authorization (to assign one shell profile and one command set).
The router is configured with the follows commands:
[code]....
View 4 Replies
View Related
Jan 6, 2011
Attached is what i have done for command authorization for privilege level user 2
View 27 Replies
View Related
Jul 19, 2011
I have a 7606 router with sup 720-3bxl. IOS has been crashed recently and i can use only Roman mode now. Ive tried to upload ios image using tftp server but the command tftpdnld id not available in this router. I don't know why. Then i tried to boot from flash disk but finally it also shows an error like
System received a Software forced crash signal= 0x17, code= 0x24, context= 0x42359674 PC = 0x402d248c, Cause = 0x1020, Status Reg = 0x34008002
How to make the router in running condition.
View 3 Replies
View Related
Dec 20, 2012
I just purchase Cisco LAP-1042N for my office network expansion. When i console into the AP via serial. I am not able to used "configure terminal" command to set my AP name,static IP address.
I tried using "debug lwapp console cli" command it did not work. below is the capture screen of the error i am getting when assigning AP hostname. Error message : command is disable.
View 7 Replies
View Related
Mar 10, 2013
I'm coming from a 5505/5510 ASA to a 5512x. I see the following 7.2 commands are now set with the NAT command in 8.6:
-------------begin 7.2 commands---------------------
global (outside) 1 interfaceglobal (inside) 10 interfaceglobal (wireless) 1 interfacenat (inside) 0 access-list nonatnat (inside) 1 192.168.3.0 255.255.255.0static (inside,outside) tcp interface www 192.168.3.114 www netmask 255.255.255.255static (inside,outside) udp interface 5008 192.168.3.117 5008 netmask 255.255.255.255static (inside,outside) tcp interface 3390 192.168.3.101 3389 netmask 255.255.255.255static (inside,outside) tcp interface h323 192.168.3.118 h323 netmask 255.255.255.255
--------------end 7.2 commands----------------------
View 10 Replies
View Related
May 28, 2012
What is the command switch (the letter/s that you use withsign after the command) that can be used for displaying the per protocol statistics with the above command
View 1 Replies
View Related
Oct 21, 2012
I am using ASA 5520 Image in GNS3, when i come in Configuration Mode and try to create Tunnel through command "interface Tunnel 0", but this command doesn't exist. I need this command to create Tunnel for GRE Lab.
View 2 Replies
View Related
Aug 1, 2012
I have copied status codes from show ip bg command output and its explanation (from Cisco documentation site)., d and h (suppressed, dampened and history). I read somewhere that these are to control flapping routes. But not able to understand it completly.Raised this question in a couple of forums but didnt get a proper reply.The table entry is suppressed.??The table entry is dampened. ??The table entry history. The table entry is validThe table entry is the best entry to use for that network.
View 2 Replies
View Related
