Cisco WAN :: C1941 - Getting Time Out For VTy Login In Telnet
Mar 14, 2013
1) KA-AGR-DEP-C1941#telnet 74.125.236.133 /source-interface gigabitEthernet 0/1
% telnet connections not permitted from this terminal
How can we enable telnet for the above for testing
2) KA-AGR-DEP-C1941#sh caller
Active Idle
Line User Service Time Time
vty 132 agri VTY 00:02:24 00:00:00
Here we are getting the time of our vty login and not the serial link uptime. How can we enable to check the serial link uptime.
3) CGHSULSOR#traceroute google.com
Translating "google.com"...domain server (164.100.3.1) [OK]
Type escape sequence to abort.
Tracing the route to google.com (74.125.236.129)
1 10.161.20.69 4 msec 4 msec 4 msec
2 10.255.232.38 4 msec 4 msec 4 msec
3 10.255.238.237 40 msec 40 msec 40 msec
4 10.255.221.225 40 msec 40 msec 40 msec
5 * *
CGHSULSOR#telnet 74.125.236.129 80
Trying 74.125.236.129, 80 ...
% Connection refused by remote host
In the above case it's showing refused by remote host. If the port 80 is opened in firewall also if we get this error what will be the issue. As i understood when firewall port is opened we wil get as OPEN
View 4 Replies
ADVERTISEMENT
Dec 29, 2011
I was logged in to this device in monday normally and in tuesday when i trying to
Cisco SW#telnet 172.17.1.1
Trying 172.17.1.1 ...
% Connection refused by remote hos
And i compare the current configuration with last configuration in monday i found no change, this device in live network also cpu is normally and memory.
View 2 Replies
View Related
Sep 12, 2012
This is the great place for ACS discussions , i need two more inputs from experts
acsserver
Thu Sep 13 14:35:28 UTC 2012
pughaz
15
[ CmdAV=ip tacacs source-interface FastEthernet 0/1 ]
Device Type:All Device Types:ROUTERS, Location:All Locations:NON DC DEVICES
On the above message
1. Need to chang time from UTC to IST
2. The Device column is not showing the exact device name ; i telnet and config changed , it is showing the device group name only , how to get the exact device name i telnet on this message
View 1 Replies
View Related
Jan 7, 2013
We have a cisco 2911 router configured with password for telnet login, but I always failed to login use telnet, does any one know any place need to be modify?
View 6 Replies
View Related
Oct 8, 2012
We have dialup users that are connecting to our portal for uploading/downloading credit information. We are currently using ACS 3.3. There is a requirement that, initially we provide clients with their username/password, but we want to enforce the policy that when the user logs in first time, he should be prompted (forcefully) to change his password.
1) Can this be done in ACS 3.3
2) What solution shall be used in this case ? can it be done in ACS 5.3 ?
View 5 Replies
View Related
Aug 16, 2011
I want to configure IOS SSL VPN on C1941 Router. let me know if any additional License is required for that.
View 1 Replies
View Related
Aug 5, 2012
i have Cisco 1941 router with following IOS image:Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M5, RELEASE SOFTWARE (fc2) below mentioned commands are not working :
crypto isakmp policy 5
encr aes 256
authentication pre-share
group 2
what could the issue ? do i need to change the IOS image.
View 6 Replies
View Related
Apr 24, 2011
I have two C1941.The first C1941 does not support SNTP but the second C1941 supports SNTP. The only difference which I can spot is their license. The first C1941 does not have security license but the second C1941 has. What is the URL that has info on what IOS commands are supported on IPbase license, sec license..etc
First C1941
C1941_1(config)#do sh ver Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)Technical
[Code].....
View 5 Replies
View Related
Jul 18, 2011
Does WLC 5508 has capability to create login credentials with specific time of validity? Could it be used in hotel set-up to provide prepaid access account to guest?
View 2 Replies
View Related
Feb 10, 2012
I have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
View 19 Replies
View Related
May 9, 2013
We have a Linksys WRT120N wireless router set up at one of our small offices. I noticed recently when trying to log in to the router to make some admin configurations that it will not accept the login credentials when trying to log in from IE10 browser. Works fine from Chrome, IE9, ect. logging in to a linksys router with IE10?
View 3 Replies
View Related
Jan 4, 2011
I have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies
View Related
Jul 8, 2012
I just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies
View Related
Jun 29, 2011
Ciso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
View 5 Replies
View Related
Oct 26, 2011
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies
View Related
May 1, 2012
I recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies
View Related
Jan 17, 2012
Is the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies
View Related
Jan 10, 2012
AI have a Dir-825 router. The 5GHz is turned off and the wirless is on G/N. I have shawcable for my isp and my firmware is 2.06 and its a Rev B Router. I also have Qos Engine on for allowing me to have 2 xboxes on Open NAT.problem is my wireless signal for some wired reason is VERY weak. A while ago it used to work really far way outside. It was around 150ft distance at 4 bars. Now for some reason I can't even go upstairs without getting a 1 or 2 bar signal.
View 3 Replies
View Related
Sep 1, 2011
i have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
View 5 Replies
View Related
Feb 16, 2011
Cannot connect to ACS device using telnet IP: port 1812? Seems it is using this port config by default.Is it because of the port it's trying to use? Is there a way of changing the port? If so, where does one do this in the ACS device?I have two 4400 series WLC's one is on the same network segment as the ACS, I can authenticate through the ACS on this one. The other WLC at a different location, cannot authenticate through the ACS.
View 2 Replies
View Related
Jan 26, 2012
I have a 891 router I have been testing some things on. I have been able to successfully telnet to it in the past with no problems. Just yesterday I was trying to set an interface to have an IP of 10.10.10.2 which I realized was an IP I had forgot to exlcude from DHCP and it was handed out to the computer I was using to telnet in. So I wrote in the exlcude commands and did an ipconfig -release ipconfig -renew on my PC that had the 10.10.10.2 IP. After the renew I was given 10.10.10.7 (put in a few more excludes).However the release dropped my telnet connection and afterwards I was completely unable to telnet in, getting the error that says I cannot open the connection on port 23. I had made some changes to my entire config beforehand which had it switch to use a new public IP. I never saved the changes and did a hard reset by unplugging the router to get my old config back and see if I could telnet after that. Still could not get in, same error. Well I went through and remade my entire config to use the new public IP. My 10.10.10.7 PC can access the internet, DNS, ping the router, all just fine. Still can't telnet. I remade my line/vty config and made sure it matched up with a config I had on another router. Still can't telnet. Last thing I did was go in and manually clear all open line connections. All that is left is an idle 0 con 0 line that it wont let me close. Still can't telnet.What the **** is going on with this thing? I am completely at a loss to explain why I cant telnet. It must be something in my ACLs that I am missing?
View 2 Replies
View Related
Feb 16, 2012
I have a cisco 3750 switch and i given 2vlans (40, 118). 40 is local and 118 is public.I given the public ip for vlan 118. now i am able to telnet from same vlan (118 only) but i am not able to ping and telnet as globally. [code]
View 5 Replies
View Related
Oct 24, 2011
1.SCP Not Working on my Linux Box (Fedora release 7 (Moonshine))to Fedora fc11.i686 running box[CODE]
View 5 Replies
View Related
Feb 10, 2011
I have the following configuration to enable me telnet to a cisco switch, but couldn't even ping the 192.168.1.22.
vlan 22
!
conf t
int f4/4
switchport mode access
switchport access vlan 22
[code].....
View 8 Replies
View Related
Apr 19, 2013
I have one router 3925 equipment DIRECTLY connected to the Router that needs to be accessed by telnet port 23.
Please find the attached config details.
View 6 Replies
View Related
Sep 27, 2011
I have a problem, recently I can not telnet to the ACE 4710, the ACE version is A4(2.0). I can enter by web and console but not for telnet. I try to give more resource to the admin context but it doesnt work.
View 1 Replies
View Related
Oct 15, 2011
accessing my cisco ASA, last night we were doing VA on our ASA, after that iam not able to access it through ssh nor telnet. its not giving me any error.. i tried from different system also. SSH & telnet allowed from inside to 0.0.0.0 i have re-generated rsa keys when it was working. ASA version is 8.2 now when i connect telent is giving me blank prompt. i can login using ASDM.
View 5 Replies
View Related
May 19, 2012
I have more than 20 SF 300-24P 10/100 Managed Switch switches deployed and running in my office network. All these switches have web configuration utility enabled. We would like to enable telnet too. But for this I know I have to visit site to site, connect the switch manually with a laptop and enable telnet option. I am looking for how can I enable telnet in these switches using web-based switch configuration utility.
View 3 Replies
View Related
Dec 19, 2011
On a LMS 4.0.1 :I want to know what is the right way to change the telnet program on the campus mgr map (topology services map), when right-clicking a device icon and selecting telnet.I would like to use a tool of mine, and not to launch a telnet command from the IE browser.I changed the default telnet of Windows in the registry, but the program is still launched as a telnet URL in the browser and this is not what I would like to do.
View 2 Replies
View Related
Jan 13, 2013
I am trying to set up SSH/Telnet on a WPA2000 Wireless-G Access Point. I have looked for documentation but am unable to find any that says how to do this via the GUI, and I cannot see any obvious place where this could be. How to set this up? I would prefer SSH but telnet will do.
View 4 Replies
View Related
Dec 18, 2011
I have Cisco router 851 at my region site. It has five Fa ports. One of them is connected to ISP and has ip address 10.1.1.2 (for example). It also has vlan 1 interface, that has ip address 192.168.0.1 (also for example). I also have Tun0 interface that goes through ISP network and connects to my hub network. The rest of Fa interfaces are swithcable and they are in vlan 1.The problem is that from hub LAN I can telnet to 10.1.1.2 ip address, but I can't telnet to 192.168.0.1. Whereas I can Ping 192.168.0.1 from my hub LAN.
Topology:
Hub LAN -------ISP---------Spoke Router 851
View 8 Replies
View Related
Oct 7, 2012
I am not able to telnet or ssh to ASA running 8.2.5(33). [code] I am able to ping inside interface of the ASA. Telnet gets stuck at Trying
View 2 Replies
View Related
Sep 3, 2012
I am facing an issue with a cisco 877 router. I am not able to telnet to this router from outside using the public IP. I have also notices this works when the Nat is removed.
View 7 Replies
View Related