Cisco Switching/Routing :: 2960 / 3750 - IP Address Conflict?
Feb 7, 2012
I have switch 2960 and router that connect with one interface to that switch. the link is trunk and Router function is inter vlan routing between 4 vlan. This netwrok has only one ip address space that is 10.10.2.0/24 and work without problem. We connect cisco switch 2960 with optic link to another switch that in stack 3750 which configured as trunk link and allowed only 3 vlan between them. In the other side netwrok which consist the switch 3750 we have different subnet ip address that switch working in layer 3 too. the problem is that when I permit vlan 210 in the switch 2960 only layer 2 between this switch and the 3750 in network that consist th ip address 10.10.2.0/24 devices, if I disconnect and then connect pc to network he says that he has ip conflict and in the log he show mac address of router that has vlan 210 subinterface configured with 10.10.2./24 subnet. But how I gibe back vlan 210 from permited vlan in trunk devices start normaly working. If I again put vlan 210 to permit vlan in that trunk devices again said that there are conflict ip address and show mac address vlan 210 router subinterface.
View 10 Replies
ADVERTISEMENT
May 2, 2012
I just found out that one of our 10 3750's has been assigned with an IP Address that is in conflict with a PC that has been in production long before this 3750 was deployed in our environment. Good thing it is servicing devices on a separate vlan. The conflict IP Address is assigned to the default vlan of the switch so we can connect to it from the core.If I change the IP Address of the switch, will it reboot and momentarily disconnect the devices connected to it?
View 14 Replies
View Related
Dec 19, 2012
We are going to upgrade our IOS on our WS-C2960G-48TC-L. But before we do that i want to ask whats the best IOS release to choose. Why we want to upgrade is because our switch software now don't support ssh just telnet access
Switch details:
Model: WS-C2960G-48TC-L
SW Version: 12.2(25)SEE2
Image: C2960-LANBASE-M
I was thinking about upgrading the IOS to 12.2(44)SE6 are maybe i should upgrade it to a newer release?
One more thing we have a bunch of stacked 3750 switches, that also need to be upgraded.
View 7 Replies
View Related
Nov 21, 2012
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies
View Related
Jul 26, 2011
Yesterday Cisco released IOS 15 code into the wild for the 2960 and 3560/3750 families but the link to the release notes is not working. Because I already have a whole bunch of 4500/Sup7's running IOS 15 I am thinking about taking the plunge with 30 3750-X's I have on order but want to review the release notes first. where they might be hiding?
View 4 Replies
View Related
Jul 26, 2012
I'm fairly new at trying to create isolated network segments on Cisco switches. What I'm trying to do is have multiple isolated paths that originate from my v Sphere infrastructure travel through a layer 2 link, v LAN, up to a MLS, and ultimately out to to the internet through a firewall. Each sub net might ultimately have a number of hosts on it, but I don't think the make up of those hosts will matter here.
My initial thought was creating v LAN tagged port groups on v Switches on my v Sphere infrastructure. Physical connections will go from my ESXi hosts to the 2900 series Cisco switch connected to trunk ports. Both v LANs would be configured on the switch but not assigned to physical ports. The physical connection to the 3750 would also be a trunk port connection from the 2960. The 3750 would have SVI's created that are attached to VRFs that would control route traffic. This might be totally wrong but from what i've read it seems to be going down the correct path I think.
Two part question, is this the best way to go about designing this network? If so I seem to be really struggling with the SVI/VRF part. Every time I create an SVI all of my hosts on the 10.10.10.x network can ping them, regardless of which v LAN they're on.
I just cannot seem to isolate the 172 network.
View 3 Replies
View Related
Feb 19, 2013
how to stack 2 switches catalyst 2960 also haw to stack 2 cisco 3750 switches
View 3 Replies
View Related
Mar 25, 2013
We have a pair of WS-C3750X-24T-S in a stack and four WS-C2960S-48TS-L in a stack of their own. There is not really anything too fancy configured (no special VLAN configuration/trunks or etc.) but the 3750 do have two ports configured as L3 for routing. We are not trying to use those ports for EtherChannel. These devices are running IOS 12.2(55)SE3 Essentially we are attempting to make an EtherChannel group using port 48 on all four of the 2960's in their stack (four ports). On the 3750 we will configure an EtherChannel group using port 23 and 24 on both switches (four ports). We then connect them up to form a four member EtherChannel.The ports on both ends are configured as mode ON and they are all 1Gb ports. I elected mode on because I understand at least one of the EtherChannel protocols will not work cross stack. What I would like to ask is whether the above configuration is possible or are we hitting some sort of limitation of EtherChannel cross stack, etc..? I cannot find anything to suggest this configration is invalid, but thought I would ask to see if I missed something in the EtherChannel articles.
View 3 Replies
View Related
Sep 17, 2012
I have 2 switches. 2960 and 3750. I have trunk on both ports of the switch. there are couple of vlans and ports are assigned to those vlans. examples are management, voice and data. int vlan 1 has ip there is default gateway the hosts are able to connect to the internet when connected to the switch.
View 5 Replies
View Related
Aug 15, 2012
I am experiencing the same problem described in this post {URL}. I have seen this happen on different networks, with different equipment attached. It happens on both 2960 and 3750 switches. Basically the connection drops, and we see in the web interface "Port is Disabled". This appears to happen every 10 minutes.
On the CLI, the status shows as connected.
Port Name Status V lan Duplex Speed Type
Fa0/38 connected 1 a-full a-100 10/100BaseTX
I have ran cable diagnostics while the drop out is occurring.
Interface Speed Local pair Pair length Remote pair Pair status
--------- ----- ---------- ----------------- ----------- -------------------
Fa0/38 100M Pair A 28 +/- 15 meters Pair B Normal
[code]...
During the outage, I see the duplex fluctuate between full and half. The outage occurs for approx 90 seconds. If I fix the duplex and speed at both ends, the outage reduces to around 30 seconds. If I apply spanning-tree port fast the outage reduces further to around 10 seconds. Before I change any configuration on the port, the logs show the interface going down
Aug 16 13:06:51.875: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/38, changed state to down
Aug 16 13:06:52.874: %LINK-3-UPDOWN: Interface FastEthernet0/38, changed state to down
[code]...
However, once I apply the configuration nothing is logged. However we can still see the connection is disappearing for around 10 seconds. I suspect the issue wasn't resolved for the person reporting the problem in the link above, but because the outage is minimized, and not being logged it is going unnoticed.
View 30 Replies
View Related
Sep 4, 2012
I have a problem, here are the situation
- 1 Catalyst 3750
- 1 Catalyst 2960
- 4 Finger Print
- 1 HUB
Configuration
- Catalyst 3750
Interface VLAN182
IP Address 10.62.182.254 255.255.255.0
Interface G0/2
Description Finger Print Server
Switchport mode access
[code]....
Here are the problem,If i connect Finger Print Device to port catalyst 2960, some device not sending data to server, but if i connect all Finger Print to HUB and from HUB connect to Catalyst 2960 at port F0/5, All Device(Finger Print) can send data to server...Is there any special configuration in catalyst so all device can direct connect to port catalyst 2960 without HUB?
View 3 Replies
View Related
Nov 13, 2011
I am trying to setup a network using Cisco 2960 switches with vlans configured. One vlan will handle video coming from four cameras that are connected to another 2960.
We have four cameras feeeding one port each on a 2960, that 2960 in turn feeds one port on the main 2960 which is the video vlan for that site. From the site it goes back to a Cisco 3750 to be sent over to a Sonicwall firewall. If we connect to the 2960 that the camera are connected to we can see the video, but not on the main site 2960.
View 5 Replies
View Related
Dec 4, 2011
How do I create static smartport macro on Catalyst 2960 & 3750 equivalent to below static smartport macro:
macro name NOT_USED
description UNUSED_PORT
switchport
switchport mode access
switchport access vlan 100
shut
@
I am able to create above smartport macro on Catalyst 3760 & 6500, but not on 2960 & 3750 (see below):switch(config)#macro ? auto Macro autoexecution settings global Enter global macro configuration
View 12 Replies
View Related
May 20, 2013
This is probably a dumb question, but I have read the 2960 stack administration guide and it does not explain how to configure the stack IP address. It says several times that the stack can be managed from the stack IP address, and that the stack IP address is a system-level configuration item. But it never explains how to configure the stack IP address.
View 3 Replies
View Related
Mar 14, 2013
I have two 2960's in this new environment that I am administering. I am receiving a message on one unit (Designate it 2960-2) of %IP-4-DUPADDR: Duplicate address 192.168.168.8 on Vlan1, sourced by 3037.a63e.540. The "sourced by" address is the 2960-1. I do not know how these units were originally set up. How can I determine where the duplicate address is originating from.When I perform an ARP -a the address that corresponds to the 192.168.168.8 is the mac address of the ethersvi interface on the 2960-1. I
View 3 Replies
View Related
Sep 29, 2012
I configure 3750 stack switch as core and 2960 stack switches as access layer switches.I connected my laptop to one of my core stack in VLAN 10 and I am pinging to one of my server in VLAN 1. What will be the minimum latency at the time of inter VALN routing
View 2 Replies
View Related
Jul 30, 2012
I am configuring a Cat 2960 port for connecting a VOIP phone, authenticated by MAB. On connecting the phone, I get the port authenticated and assigned to the correct VLAN, with LLDP-MED advertising the correct voice vlan. However, I then see no traffic from the phone on the switch. I can see the MAC address of the phone is learned in the right VLANs, but the mac address is showing as "Drop", which normally means the address is statically configured to be blocked. There is no static mac address table blocking configured on the switch.
Switch Version
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 50 WS-C2960-48TC-L 15.0(1)SE3 C2960-LANBASEK9-M
Port configuration
interface FastEthernet0/1
description "Standard user port"
[code].....
View 1 Replies
View Related
Apr 19, 2009
How to change ip address in cisco 2960 series switch?
View 4 Replies
View Related
Dec 20, 2011
I have a cisco2960 with c2960-lanbasek9-mz.122-50.SE4 imagebase.This switch is connected with 3 unmanaged switches.Though 2960 is managed and only a single vlan is given accessed to connected other unmanaged switches.Problem is this, if at user end, a laptop is connected ( Microsoft Vista OS) and its IPv6 is checked in the LAN properties settings then the laptop's IP address changed from our VLAN to 192.168.100.x series and due to this other connected user's DNS addresses become changed.Hence I want to block this IP or its MAC on Cisco 2960.
View 1 Replies
View Related
Nov 15, 2012
Does the 2960 switches with LAN-Lite support DHCP Server Port-Based Address Allocation?
View 1 Replies
View Related
Apr 15, 2012
There 's a Cisco IP phone that sits between a PC and the switch port. On the switch port, no MAC address is learned. However, the switch is able to detect the IP phone and deliver power to it: [code] Switch is Catalyst 3750 with IOS version 12.2(58)SE1.
View 1 Replies
View Related
Oct 16, 2012
Today when we run one applcation to access a target server with IP address 10.2.2.13, the application cannot run through and appearing error message related networking.The target server has two network ports whereby another one with IP 10.2.2.14 is running OK with the same application. All these two connections are connected to the same Cisco switch 3750, after the switch then go to Cisco ASA firewall which has no access control rule for this 10.2.2.13 and its subnet, and then the firewall connect directly to the application server.We can ping, remote desktop access and telent port for the application to the target server by using 10.2.2.13.We swapped the cable connection of the ports from one another and try the application again, the IP with 10.2.2.13 is still fail and IP with 10.2.2.14 is OK.We then change the IP from 10.2.2.13 to 10.2.2.12 or 10.2.2.155, all are OK. We changed back to 10.2.2.13, it is failed again.The switch is in running real time production and so we cannot power cycle or reload the switch.
View 9 Replies
View Related
Dec 11, 2012
a new LAN installation, two VSS pair 6509 core, 15 closets, with 3750 stacks. Floor 15 only, devices/hosts can ping teh DHCP server but cannot aquire IP addresses. no such problem on other floors?
portfast an dother parameters are intact.
View 2 Replies
View Related
Feb 27, 2013
There is a unicast flood on 3750 killing slow modem links. How to determine source MAC address of flooder? Is there a rate limit feature for it?
I know how to block it completely on port-level, but it breaks normal network operation. (when port goes down for some reason, it's learned MACs got flushed and since other hosts know MACs, they keep flooding untill their arp caches expire).
View 11 Replies
View Related
Oct 23, 2012
I have some question about HSRP in 3750 switch. I have two Cisco 3750 switch which configured HSRP. Let say, we have interface vlan 100 that join in HSRP group member 1. The configuration on both switch is like as follows :
SWI-3750-A (Active)
==========
interface Vlan100
description *** gateway User NPL ***
[Code]....
View 8 Replies
View Related
Apr 21, 2013
We have VSS configured between Cat-6509 switches (s72033-advipservicesk9-mz.151-1.SY.bin)..For the voice vlans,dhcp scope is configured within VSS and ip addresses are assigned to ip phones from these pools configured within VSS.Cat 3750 stack is connected with dual links to this vss. IP phones are connected to cat 3750 switches and desktop is connected back to IP phone. For data vlans IP addresses are assigned from external dhcp server.
Currently we are facing lot of ip conflicts for ip phones and after clearing the dhcp conflicts, IP phones starting getting IP addresses..(sufficient IP's do available in the dhcp scope for IP address assignment). (What exactly the role of no ip dhcp conflict logging command......)
View 4 Replies
View Related
Feb 7, 2012
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies
View Related
Feb 11, 2013
I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies
View Related
Jun 3, 2012
I had problem with IP conflit address from cisco router 2911 , all the time the router respond with ARP reply (duplicate use of IP : x.y.z.t with the same Mac Address ) and the IP subject of conflit dosen't appear in any router's interfaces configuration (basic configuration without dhcp) ,the problem was solved problem when I desactivete proxy arp but I can't understand this behavior , why arp proxy respond to all IP address with same Mac even the IP dosen't exist in router ?
View 4 Replies
View Related
Sep 8, 2012
I have a network topology which you can see on image. All routers are Cisco 3745 with IOS (C3745-ADVENTERPRISEK9-M), Version 12.4(12). SW1 is L3- switch Cisco Catalyst WS-C3560E-24TD with IOS (C3560E-UNIVERSALK9-M 12.2(58)SE2). [code] After that I have problem. When PC with OS Windows 7 begins to work in corporate network, it sees "coflict ip addresses" and doesn't work with network. I've used wireshark and seen, when the PC send arp request a SW1 always send arp reply (see attached file). I think problem with command "ip sla responder", but I haven't searched information about it and I want understand this is bug or normal functioning.
View 1 Replies
View Related
May 10, 2013
I configured an DHCP server on cisco 3750 switch . Wher in w3750 gets connected to plain l2 switch 2960 on floor and machine gets connected to 2960 port. [code] Below is the description of problem:
-> The Cisco 3750 switch is the DHCP server. VLAN 108 is named as internet vlan.
-> Ports in Cisco 2960 switch has been configured with "switchport access vlan 108".
-> There were no problems at all and everything had been working smoothly.
-> 3 days back, users started complaining that they couldn't access the internet. Up on troubleshooting the issue, I found out that there was an issue with the DHCP server as the computer couldn't get any IP address at all. After setting static IP address, the internet started working again.
If I bind IP to MAc address reservation on core 3750 switch for some time of moment it works but after that machine gets unreachable .I restarted the 3750 switch and also all the 2960 switches over the weekend, however, the issue still hasn't been resolved yet. I did issue the command "clear ip dhcp conflict *", clear ip dhcp binding * but no joy at all.
View 2 Replies
View Related
Apr 22, 2011
When I sign on the internet, I get a Windows System Error - "There is an IP address conflict with another system on the network." I went to command prompt and typed "ipconfig /renew" but the response was "No operation can be performed on Local Area Connection while it has media disconnected".
View 1 Replies
View Related
Jan 29, 2013
I've got a wireless network, consisting of two Windows 7 PCs, a wireless printer, an Android tablet and an iPhone. The PCs are always on the network; the other devices only connect occasionally. The router is a Dynamode R-ADSL-C4-W-G1. IP addresses are assigned by DHCP, and both PCs are set up to get an IP address automatically.Now and again, I get an error message on my PC, saying Windows has detected an IP address conflict on the network. I looked in the System Event Log, and found the following message: Quote:The system detected an address conflict for IP address 10.0.0.3 with the system having network hardware address [hex number here]. Network operations on this system may be disrupted as a result.
When I checked in the router settings, I found 10.0.0.3 had been assigned to the other PC, which also has the hardware address given in the error message - I'm not sure how that constitutes a conflict!When I get this error message, I never encounter any connectivity problems - i.e. both machines can still access the internet.
View 5 Replies
View Related
