I have a single DL 380 G5 server with 2 NIC , i have 2 applications which run on 2 separate WAN static ip addresses my query is that can i install both the applications on a single server ? secondly can i assign 2 different WAN static ips on the 2 NIC of the same server ? if yes then how it will be done i.e whether gateway will be given to both the NIC or only a single one
View 11 RepliesI have 2 servers, one active, the other standby, both will be using the same IP. If the active fails then a re-patch for the standby to make this the active. I understand that i will need to clear the arp & maybe mac address table on the 6500 for the new active server to work, as the failed server will have its mac address on the 6500,.
is there a way around this so i dont have to clear the arp cache & clear the mac table? [code]
I am a recent student to Cisco products and I have purchased some (what I thought was good) lab equipment to learn with on a budget. What I have is a 2948G switch and a 2620 router. My issue is this: the router has only one fast Ethernet port. Is it possible to use V LAN's and V LAN Interfaces on the router and switch to somehow emulate a second interface to connect to a WAN or sub net?
View 11 Replies View Relatedhow to upgrade firmware on 4507 6L-E Sup. There is only 1 Sup on the switch. is there any special requirement to update the firmware when switch not running on redundancy mode?
-core-1#show redundancy states my state = 13 -ACTIVE peer state = 1 -DISABLED Mode = Simplex Unit = Primary Unit ID = 3
Redundancy Mode (Operational) = Stateful Switchover Redundancy Mode (Configured) = Stateful SwitchoverRedundancy State = Non Redundant
[Code] ......
I am trying to convince our Technical Lead that dual VSL links between our 6509-E chassis is a VERY good idea but he is fully convinced that the setup will work perfectly fine with only one VSL link. As I do agree that we can do this, I am looking for more concrete evidence that shows this would be a bad setup.
I know that we will lose the High Availably that comes with VSS, what I don't know is what will happen to all of the downstream switches that are connected and what will happen to the two 6509-E chassis..
I got a different scenario from one of my client.My client have two different branch offices and have 50Mbps point to point connectivity between them. All users in both braches using same series of IP pool ( 192.168.224.0/24) in both branches.Both branches he had only Cisco 2960S series switches only. And in both branches he is using IP cameras. He will monitor the assets by accessing IP cameras through the browser.His requirement is, he wants to prioritize the Video traffic( monitoring through the browser) over the normal data traffic.Note: He had a single VLAN only.
View 8 Replies View RelatedI'm looking to see if it is possible to run a vPC between to vDC's on a single 7010? We have a Production setup that runs dual 7010's with vPC's between the chassis but in our lab we only have a single 7010 with a 32 port 10gig module. I was thinking that maybe we could create 4 vDC's on the 7010 and run a vPC between the vDC's.
View 2 Replies View RelatedUsing SFP-10G-LRM with single mode fiber? We have 1310nm.
View 2 Replies View RelatedI have a 3750X 24 port switch (with NM-1G network module) running IOS 15.0(1). Is there any benefit or reason to plug in the included Stack Wise cable and loop it back to itself in a single switch installation?
I don't see any recommendation in the documentation. The data sheet indicates a single switch is a non-blocking device so I'd think there's no bandwidth advantage like there is when connecting an actual multi-switch stack and needing to close the loop for the full 32 Gbps stack bandwidth.
I have a customer with three rooms where teh access layer aggregation switches are run back to.
Access Switch Stack A -> room 1 + room 2
Access Switch Stack B -> room 2 + room 3
Is it possible to have three Nexus 7000s ie one in each room (1,2 and 3) and have them setup like this:
Nexus 7000#1 vPC domain 1
Nexus 7000#2 vPC domain 1 + vPC domain 2
Nexus 7000#3 vPC domain 2
Thus gving all access switch stacks redundant links to the core withouit spanning tree.
I know its not ideal but its a campus site and thats how the existing fibre runs go.
I would like to know if it is possible to assign a 3rd IP address to my end user vlan. Basically the 45xx acts as my end user gateway and has been confirgured as below
interface VlanXX
description Main Vlan
ip address 2.X.X.X 255.255.255.0 secondary
ip address 1.X.X.X 255.255.252.0
[Code].....
Here, due to IP address exhaustion in my end-user network, i want to add one more subnet X.X.X.X/22 to my network and assign one IP more from this range to the above vlan to act as the gateway IP.
I have been asked to upgrade the IOS images on three 4506 switches with a single Supervisor IV engine in each to allow for SSH2 access.The current image is cat4000-i5s-mz.122-25.EWA.bin..I have uploaded cat4000-i5k91s-mz.122-25.EWA14.bin to bootflash on each Supervisor engine.The ROM on each SUP IV is 12.1(20r). I don't want to have to upgrade the ROM version.Will the cat4000-i5k91s-mz.122-25.EWA14.bin image retain all the current features of the current image and provide SSH2 support, without requiring a ROM upgrade?Each switch has 512 Mb of RAM.If this image will accomplish what I want, what are the commands used to select the new image from bootflash. I'm familiar with image updates on fixed chassis switches using the boot system flash command.
View 2 Replies View RelatedI need to block this mac address in my 3550 switch.i enable port security but this mac address comes and do the violation and port is shut down.
View 3 Replies View RelatedIs there any way to clear a single ARP cache entry on the 6500 switch ?
View 8 Replies View RelatedI have enabled IP DHCP snooping on a 24 port 3560 switch (v small office) and let the database fill up, now I have added dynamic arp inspection on the single vlan and I amd getting these errors.
Apr 23 16:15:34: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/5, vlan 1.([5835.d9b0.b9d1/172.30.5.2/0000.0000.0000/172.30.5.3/16:15:33 BST Tue Apr 23 2013])
Apr 23 16:15:39: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/8, vlan 1.([0004.f2be.55e4/172.30.5.5/0000.0000.0000/172.30.5.8/16:15:39 BST Tue Apr 23 2013])
Apr 23 16:15:40: %SW_DAI-4-DHCP_SNOOPING_DENY: 1 Invalid ARPs (Req) on Fa0/8, vlan 1.([0004.f2be.55e4/172.30.5.5/0000.0000.0000/172.30.5.8/16:15:40 BST Tue Apr 23 2013])
[Code] .....
We have a Cisco 2911 router in our company. I didn't set it up myself nor I was involved. I only started working here recently, bit over 3 months ago. I have been given ongoing task which other IT Technicians been struggling for almost a year with a idea that maybe because I'm fresh person in the company I will find a original idea why could this thing not work.
Our router have a problem with blocking a single IP address, but not completely It's hard to explain but I will try my best. Company is hosting their website externally and accessing the host and FTP on the host on daily bases. It is important for the website to work on the internal network in company. It does work sometimes, but from time-to-time the website showing time-out error 118 on any point before Cisco router using both http and https, have tried putting just the IP address( doesn't matter is it on the general network or last ISA server on DMZ ). I am able to connect to the website using any of proxy gates but not directly to the website. I have also tested the connection past the router and I was able to connect to the website without any problems. I am also able to ping the host's address from the router and internal network.
I have eliminated the possibility of not correctly setup proxy or firewall on the network as problem also occur on the DMZ. I have also checked access-lists on the router and firewall rules for Any possibilities and I can't really see a way why would the router do this.
I have a new building to add to our campus and I have been encouraged to run single mode fiber. All of my other buildings are connected with multi-mode fiber. I just want to make sure i will not have an issue if I run single mode to the new building with SM SFP's.
View 2 Replies View RelatedNexus infrastructure is pair of N7K switches, with dual homed 5K/2K devices connected, links use vPC. They want to extend vlan's from the 5K/2K side across a L2 path into another DC, this path is only connected into one of the N7K switches, call this 7K switch A.I'm concerned that packets from the 5K/2K side back to the remote DC could get dropped due to the vPC loop dectection process. If a packet from the 5K/2K side traverses the path into the same N7K (7K switch A) as the L2 extension, I dont see a problem. But, if the etherchannel load balance in the 5K sends traffic to the packet to N7K B, in order to get to the L2 path extension to the remote DC the packet gets forwarded across the vPC. My understanding is that this packet will get dropped by N7K A as its local L2 path to the remote DC is up, is this the case?I see a solution is to plug the L2 path into a 2K, but before I suggest this is my understanding of the loop detection process correct?
View 1 Replies View RelatedHaving a strange issue here with an 7606-s chassis equipped with two sup720's, and two regular line cards. There is only one power supply, PWR-2700-AC. I recently builded this setup and powered it on last week for the first time. It ran fine for about 20 minutes while suddenly the chassis powered down.
I've checked the back of the chassis and noticed that the power supply had it's 'input ok' and 'power fail' led lit. I toggled the power switch and waited half an hour to power it on again. This time only 1 minute of joy. My first idea was the PSU due to the power fail led so I had it swapped by the supplier for another. Unfortunately, when I powered it on today, it didn't change a thing, still unexpected power downs.
So I've checked the following documentation: [URL] and followed the suggestion to power the chassis on without any modules in the slots. So I did that and it ran for 8 minutes only. However, the fan tray did respond properly when I removed the small thermal module in the upper right by increasing the fans to full speed.
Following above documentation, it points to the chassis (there is not much left). Now the real question comes, isn't there anything else that could be the cause of this?
Could I configure and connect 3 Dell switches to an ASA-5525 Firewall which has got 8 interfaces.
View 7 Replies View RelatedI would like to configure a 3750 switch port to be able to use two vlans. I know you can do this with a voice and data vlan, but what about two data vlans ? Say I have two devices, one on a 10 subnet and the other on a 172 subnet, but i only have one wall jack for both devices to plug into. So I use a mini switch to connect both devices and connect the switch to the wall jack; and of course this all leads back to one switch port. When I go to enter the switchport access vlan 172 cmd, how would I also make it so the device on the 10 subnet could route out ?
View 9 Replies View RelatedI have a live 28port Catalyst 2960S switch. By live I mean that there is an essential piece of equipment plugged into this switch that can suffer little to no downtime. Over the course of time the number of devices patched into this location has increased to exceed the 24 ports available and we have had to resort to adding unmanaged switches to fill the need. We have acquired an additional 2960 & stacking modules that I would like to stack together, keeping the existing switch as the master. It is my understanding that the stacking modules are hot-swappable and that this member switch can be added without bringing the master switch down, thus creating zero down time for the financial server that is connected.
The steps I believe that need to be followed are as such: write mem to existing switch and backup to our TFTP serverinstall the stack module in the existing (while powered up) and new (while powered down)place the 2 redundant FlexStack link cables on both switchesthen simply power the member switch on After boot the member switch will get it's OS and configuration from the master and I can begin moving CAT5 cables from the unmanaged switches to the stack.
I'm looking for switches that support single mode fiber connections and would like to know if "WS-C3750-FS-S Catalyst 3750 24 100BaseFX + 2 SFP" and "WS-C3750G-12S-S Catalyst 3750 12 SFP" can serve the purpose?
View 6 Replies View RelatedThe module WS-X4306, support fibber fiber single mode ó fiber multi mode? what GBIC is for fiber single mode or fiber multi mode?
View 1 Replies View RelatedWe have a single 4500 connecting to two non-cisco devices. We need to enable port channelling or link aggregation between these two.The links are carrying mulitple vlans , hence are trunked and the ip address on either side is used for routing.
From each of the two non-cisco device, i am taking 2 ports each to connect to the 4500.On each non-cisco device side, two ports will bundle together as one aggregated interface (ae1) and the other will be called ae2.
my query is how do i do the configuration for etherchannel on the cisco 4500 side , as it will need two different Po's( port channels).I need a single ip address on both sides of port channel to be present for routing.
I'm having a problem with some new gear and can't seem to figure it out. I have a 3750X-48P-S with a C3KX-10G-NM using SFP-10G-LR transceivers and I'm trying to trunk that with a 6509 that has a X2-10G-LR transceiver over single mode fiber. This is not working. Cisco TAC says the SFP+'s that we just got brand new are both bad and we need to order new ones. I find that hard to believe but who knows.
The switch recognized the module and I tested all 4 ports in gigabit mode using GLC-SX-MM transceivers, all worked great. I have the SFP+'s in tengig1/1/1 and 1/1/2 as they should be. There are no other SFP's in the module either.
When I do a sho int tengig1/1/1 and 1/1/2 the media type doesn't show the transceiver that is installed like it does for the GLC-SX-MM ones. Maybe it's not supposed to or maybe it just doesn't recognize them and it's a hardware issue.
I am troubleshooting a fiber connectivity issue.Now I have two switches, one is 3750, and another is small biz 300 series switch. Both switch has a single mode smf gbic. Now I have two swtiches face to face and connect with a single mode cable. Do you think if I would get a link light on? Both ports are no shutdown.
View 3 Replies View RelatedI have a couple of WS-C3750X-48T-L and a couple of WS-C3750X-12S-S, I want to stack all four of them together into a single stack. WS- C3750X-12S-S are running c3750e-universalk9-mz.122-58.SE2 whereas WS-C3750X-48T-L are running c3750e-universalk9-mz.122-55.SE3.I have got a couple of queries as under:What are the options to achieve putting all these 4 switches into a single stack? Can the LAN Base switches upgraded to IP Base?
View 3 Replies View Related3750 can not support multiple subnets in it's DHCP server pool config.
Is this an issue that can be fixed with a different iOS or is there a different Cisco switch that I can replace the 3750 with that will handle multiple subnets within an individual pool?
I am trying to limit the incoming and outgoing traffic on a l2 port to 8mbps for a ip subnet within the nexus 7000. The port is connected to my ISP router which has a bandwidth of 20mbps.Policing won't work on a l2 Port and shaping cannot be applied on a port level. url...I have been reading thru the qos guide for nexus release v6 and have problems understanding the different queues.
View 3 Replies View RelatedI am struggling to find an SFP transceiver, single mode, that operates at 100Mbps in a 1000Mbps port in an ME3600 or ME3800.
View 5 Replies View RelatedWe are currently using two Nexus 5548UP's as our Datacenter Network Core. I have a pretty simple objective: I would like to enable Jumbo Frames on a single VLAN only(VLAN 65). This VLAN is used strictly for backups. I do not want to enable Jumbo Frames on the other VLANs(VLANs 1-10). Im not sure what the best way to do this is.....or if it is even possible but I am hoping to get some configuration examples.
View 7 Replies View RelatedFor my Lan, I have created two Vlan; Vlan 10 = for Users and Vlan 20 = For Database Servers,There are 15 Lan computer/laptop and 5 SQL database server (Dell Server) connected through same 24 port cisco 2960 switch. Means, 15 + 5 port occupied.
I have applied access list on cisco switch to restrict communication between vlan 10 and vlan 20.But My main purpose to create two Vlan is not for any kind of communication or restriction. My main Purpose is that Users traffic do not distrub or choke or affect the Database servers. then what will i need to do for that is VLAN Concept is sufficient for my concern OR I will need to buy seperate Cisco Switch to connect 5 database servers OR Else ?