Im new to cisco routes, Im traing to configure a 1711 routes with a dsl 2wire routes, my problem is that Im able to ping anywhere in the routes, but when Im on my computer I can only ping the interfaces on the router but no the 2wire route that gives me access to the internet.
View 2 Replies
I have a 1711 Catalyst router hooked up behind a cable modem. I configured the router, copied running-config to start up-config then wrote it to memory with "write mem". I unplugged router to move it and when I plugged it back in, I had to start from scratch.
Is this normal, or should router be able to save configuration if powered down?
BTW, I'm using Putty to access router console. Is that the hot setup for Windows 7 or is there something better?
Im new to cisco routes, Im traing to configure a 1711 routes with a dsl 2wire routes, my problem is that Im able to ping anywhere in the routes, but when Im on my computer I can only ping the interfaces on the router but no the 2wire route that gives me access to the internet.
Cisco 1711 2wire
f0 192.168.200.1(Inside NAT) e0 192.168.1.76( 2wire Nat) 192.168.1.254 (Internet)
My computer is getting ip addres 192.168.200.100 when I ping th 192.168.1.76 is fine, but when I try to ping the 192.168.1.254 does not work, Im assuming the cisco has activated a dinamic route from .76 to .254, but it is not working, why?
Here is the router configuration
Router#show runBuilding configuration...
Current configuration : 1183 bytes!version 12.3service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!!no aaa new-model!resource policy!memory-size iomem 25ip subnet-zero!!no ip dhcp [Code]....
Is it possible to configure two AG241 adsl routers back to back via two wire line as a Lan to Lan network?
View 8 Replies View RelatedI have a problem between two switches with ether channel configured:
Model number : WS-C2960S-24TS-L
System image file is "flash:/c2960s-universalk9-mz.122-58.SE2/c2960s-universalk9-mz.122-58.SE2.bin"
Gi1/0/23 ETH-CH_1_SW-EDGE01 err-disabled trunk auto auto 10/100/1000BaseTX
Gi1/0/24 ETH-CH_2_SW-EDGE01 connected trunk a-full a-1000 10/100/1000BaseTX
Po1 Trunk_SW-EDGE01 connected trunk a-full a-1000
[code]...
I already change the wire without success, and already restart sw-edge02. With "u dld port disable" the link is working correctly.
I have two another switches working with SFP Cable:
Gi0/25 ETH-CH_1_SW-CORE02 connected trunk a-full a-1000 1000BaseCX SFP Cable
Gi0/27 ETH-CH_2_SW-CORE02 connected trunk a-full a-1000 1000BaseCX SFP Cable
Po1 Trunk_SW-CORE02 connected trunk a-full a-1000
Model number : WS-C3560G-24TS-S
System image file is "flash:c3560-ipbase-mz.122-50.SE1/c3560-ipbase-mz.122-50.SE1.bin"
I found a Cisco 1711 router in our storage room and I want to factory restore it so we can mess around with it or use it as a backup.
I connected a console cable to it and in Hyperterminal on a Windows XP box I want to try the CTRL+BREAK sequence to clear it out. I'm not concerned with the current config or finding the password, I just want to wipe it like it's never been used before.
This is what I get:
System Bootstrap, Version 12.2(7r)XM4, RELEASE SOFTWARE (fc1)
TAC Support: [URL]
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
[Code]....
Since upgrading some of computers in my LAN to Windows 7 they all experience upload issues. I have narrowed it down to CBAC inspection on my Cisco 1711 router, I am running IOS 12.3 I have a simple CBAC inspection set for TCP/UDP only without any application-specific inspects. Download works fine however upload does not seem to work atl all- unless I disable the ip inspection. It is all working fine for any Windows XP but not for Windows 7 machines. Is this a known issue, I am not sure how I can go about this - I don't want to build ACLs now for outside interface and disable stateful inspection mechanisms because CBAC has been working fine for me until recently.
View 7 Replies View RelatedIs it possible to configure an 881 router to act as a DHCP server to 4 VLAN's each with a different scopes all through a single ethernet interface?
View 2 Replies View RelatedI have a Cisco 881 router running 15.1(4)M4. I am trying to configure SPAN on it to mirror my outside interface (source) to one of my LAN interfaces (dest).
!--- WAN interface
interface FastEthernet4
description Comcast WAN$ETH-WAN$
[Code]......
As you can see from the above output there is a problem with the command on this interface. When I try to set Fa0 as my source it works fine:
rtr(config)#mon session 1 source int fastEthernet 0
rtr(config)#
Is this because fa4 is layer 3 and fa0 is a switchport? If so, is there another way to set fa4 as the source?
For the past few days I've been attempting to configure a data T1 on a Cisco 1760, but I'm stuck at:
Serial0/0 <our ip address> YES NVRAM up down
To provide a bit of background. This router used to be configured with a T1 via Frame-Relay; which worked fine. Now we recently change offices and providers, and the provider did not offer any information as to which encapsulation type to use, and if Frame-Relay which DLCI to use, etc.
Now I've been trying to setup the T1 connection and testing various settings such as encapsulation HDLC and PPP, but no luck. I also played around with the line codes and framing; which resulted in the following framing sf int down, line prot down, framing esf int up, line prot down. Regardless no luck.
Now I've been following several guides and examples mainly the following: [URL] In this guide they make mention of a WIC-1DSU-T1-V2, but as you can see in the show diag snippet at the bottom; we have a WIC-1DSU-T1 version 1.5. I dont' know if this poses a problem for us.
Throughout the entire process I've seen a few irregularities for example:
1. Router(config-if)#service-module t1 cablelength short 110ft
^
% Invalid input detected at '^' marker.
The IOS doesn't recognize any command with service module t1 ca , and the only recognized command with C is clock.
2. If I enter the following list of commands under the serial interface:
!
interface Serial0/0
ip address 10.0.0.51 255.0.0.0
service-module t1 framing esf
service-module t1 linecode b8zs
service-module t1 timeslots 1-12 speed 64
[code]...
And I do a sh run all I get is the following:
!
interface Serial0/0
ip address 10.0.0.51 255.0.0.0
load-interval 30
!
Although i can do a show service-module s0/0 I can see all of the configured parameters (see below)
Module type is T1/fractional
Hardware revision is 0.128, Software revision is 0.2,
Image checksum is 0x73D70058, Protocol revision is 0.1
Receiver has no alarms.
Framing is ESF, Line Code is B8ZS, Current clock source is line,
Fraction has 24 timeslots (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec.
Last module self-test (done at startup): Passed
[code]...
I have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
I've 3 interfaces on router:
Gb0/0-ISP01 with DHCP client
Gb0/1-ISP02 Static IP 192.168.2.x/24
Fa0/0 - LAN 192.168.1.1/24
I want to know, how to configure:1. Set the IP of interface Gb0/0 as dhcp client from ISP01 and make it as default route.
2. How to configure the ip nat.....overload?
3. How to use the ip sla to monitor internet connectivity to 8.8.8.8 for ISP01, if it fails, to go to ISP02.
Long time since I have had to configure a router and have a small project
Here is what I have in a simple diagram:
PC(static IP)--to--Switch--to--(Ethernet0 int, WIC0)1721 router(FastEthernet0 int, built-in)--to--Switch--to--PC(DHCP)
I need static IP PC to be able to ping the DHCP client. Static IP units 10.1.1.x/16, DHCP clients 10.1.3.x/16.
I have found these overlap and thus give errors and will even shutdown the interface if I enable certain things like routing or bridging.
So I gather I need to change one interface IP range, which would be the DHCP side, I need to stay 10.1.1.x/16 for static side.
I Have a Cisco 1941 router which had its GE0/1 port burnt out and we have since plugged in a module with 4 fast ethernet ports. I need to reconfigure the router such that at least one of the Fast ethernet ports can server the purpose of the GE0/1. GE0/0 connects to our Service provider and GE0/1 connected to the inside network.Currently, while connected to one of the ethernet ports, i can telnet into the router on the address 192.168.29.1. when i'm on the router, i can ping our remote site, network address 192.168.24.0 with no problem, but when i use the command "Ping 192.168.24.0 source 192.168.29.1" there is no response.
View 1 Replies View RelatedWe have several routers that can only be accessed on telnet port 6066 (vice 23). I have no global exec privilege so I can not provide config.So my question is: how do you configure the router to accept port 6066 for telnet and deny port 23?
View 4 Replies View RelatedI have 2921 router and I have 3 very basic switches that I need to connect to the router. The switches have very basic default configurations and there is no way to edit them, so I only have one VLAN and one default gateway. I can't assign the same IP address to each LAN port. I'm not sure how to make this setup work.
View 12 Replies View Related1. How I can manage those devices, the Switch and the router? What is the BEST SOLUTION to manage this devices?
2. I want to monitor the traffic on this environment, how I can do it? How I can monitor the traffic from customer A, Customer B, and my own LAN traffic, in terms of bandwidth that has passed throught my devices? Is it possible to monitor on MY LAN, or I have to monitor from the EXTERNAL switch?
3. How I can limit the bandwidth? I was trying to configure it using access list, with policy-map, etc....and limit this on each interface. [code]
The interface does not support the specified policy configuration and/or parameter values.Assigning a policy map to the output side of an interface not supported.With I few reading, I could see that the SWITCH 3750 doesnt support this configs.My INTERNET LINK is 30 Mbps, the ports on the Switch (WS-C3750X-48P-L) are Gigabit Ethernet.How I can limit the bandwidth here? For example, How I can limit a interface to 3Mbps..I was thinking about this:
- Limit the interface to 10Mbps: speed 10
- and limit the interface with 30% of this speed: srr-queue bandwidth limit 30
Does this work for both UPLOAD and DOWNLOAD?When the packets passes that 3Mbps limitation, will they be droped?
config to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]
View 2 Replies View RelatedI have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
I need to configure an existing 2600 router to use dynamic NAT for access to the web and ALSO I have (5) fixed IP addresses for use with an email server, a web server, and (3) future servers. I do not know the concept of how to set this up. I'm currently using dynamic NAT for the web and this seems OK but I dont know how to map my fixed servers. I assume this is done with static NAT. Do I need to add sub interfaces on the S0/0 T1 interface for each of these fixed IPs? Then do I somehow do static NAT on these fixed IPs to their respective servers?
View 14 Replies View RelatedI am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
Broken Pat/Overload after upgrade from 1711 to 891
View 7 Replies View Relatedupgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies View RelatedIn our datacenter we have a 3750 stack with IP base image. I have enabled PBR and reloaded the switch. Show sdm prefer says i am using default template. The reason i want to use PBR is that we have 2 firewalls on the same work and want to be able to have granular control over which gateway out of the network they use but still be able to access all internal resouces accross wan and locally.
Created access list to identify traffic:
access-list 10 permit 10.2.3.59 (test workstation on vlan 3)
Created policy:
route-map TestASA permit 10
match ip address 10
set ip next-hop 10.2.0.3
Assigned policy to the user vlan3:
ip policy route-map TestASA
Results:It changed the default gateway to the above gateway but i could not access any resources on any other vlan, could not access resouces accross wan.
The layer 2 switches are connected to layer 3 Switch via trunks, and routing between layer 2 switch ports with configured SVI's on 3550. All working fine. Now I'm trying to configure routing between 2800 and 3550, I tried connecting both Straight Throught and Crossover cables to the 2800 Fa0/0 and Fa0/1 ports as well as the switchports on 3550
No switchport commands are configured however, the lights do not go on for both straight through or crossover cables. I tried connecting 1750 routers but same result. My goal is to have all the VLANS routed to the internet with configuring NAT translation the router.
how do i configure the new asa 5505 to be as a router as shown in the diagram note: the isps' routers placed in head office. but i cannot change the configurations of the isp's routers.
View 9 Replies View Relatedi try to configure DNS on cisco 800 , it's worked , but after 24 hours the command ip domain-lookup change to disable, and it stop work
i'm not understanding why it's happen ,
that's the configuration
ip domain name XXXXXX.CC.CC
ip host XXX-RR-FF.com 2.2.2.2
ip name-server 1.1.1.1
[Code]....
If I have an ASA 5520 with an INSIDE interface, a DMZ interface and a WAN interface what would be the best way to configure NAT? If I configure nat-control and a nat (inside) 1 0.0.0.0 0.0.0.0 this will configure everything to be NAT'd when passing from the INSIDE interface out.My question is what about the devices I want to access in the DMZ from the inside for management etc? I'm guessing the ASA isn't smart enough to realise you're accessing hosts in it's DMZ interface so do you have to configure a nat 0 rule for every subnet within the DMZ you want to access or is there an easier way to do it? It's worth noting that the same devices will be accessing the OUTSIDE network and the DMZ network from the INSIDE network.
View 6 Replies View RelatedI have a customer who is on thr 192.168.254.x subnet and is using a Cisco 881 as their gateway.
They wish to create a second VLAN for the 192.168.253.x subnet.
The Cisco has Dialer0 configured for an ADSL connection.
I have partly configured the router but need some info regarding router a device on the 192.168.253.x subnet to the internet.
configure routing to the internet on the new VLAN and assist in setting up a DHCP server on that vlan. I have attached a copy of the current config.
I configured following command to implement QoS on Cisco 3560.
class-map match-any IND
match access-group name Lync
policy-map LyncAV
class IND
set ip precedence 4
[code]....
how to apply this QoS on interface?
I notice that NAT is not possible Cisco Catalyst 4500e series. Is there any other ways to configure NAT? Currently we have 2x Catalyst 6509 and we're migrating to the 4510e and there's NAT in the 6509s. I was thinking of re-using the 6509s and connect to the 2 new 4510e in a meshed trunking layout with MST (Layer 2) and OSPF/EIGRP (Layer 3) protocols turned on.
View 1 Replies View RelatedI am attempting to configure a Cisco 2901 router using IOS 15 to properly perform NAT/PAT translation between LAN and the internet connection.
My Configuration:
interface GigabitEthernet0/0
ip address dhcp
ip nat outside
ip virtual-reassembly
no ip route-cache
duplex auto
speed auto
no cdp enable
no mop enabled(code)
I've been trying to configure a connection which requires NAT translation but my devices are too old and seems that the configurations I tried doesn't work or I don't know how to implement it properly.Firstly, I will introduce my router to you, it is a Cisco C3640-JS-M Version 12.2(1), so I found many ways to solve my problem, but none of them are supported by it.
To continue,the connection I am trying to configure is the following one:
10.1.1.0/24(My LAN) --- (My ROUTER) --- 192.168.9.1/25 <-----> 192.168.9.126/25 --- (OTHER ROUTER) --- 172.22.1.0/24 (Their LAN)
So one host from 172.22.1.0/24 needs to connect to a server in my LAN (10.1.1.20) but they can´t use the real IP and we need to configure a NAT rule to translate traffic from them to 192.168.6.10 to 10.1.1.20, but only for this connection (there are other "WAN" interfaces.
These are my failed attempts:
interface FastEthernet0/0.302
ip nat outside
ip nat inside source static 10.1.1.20 192.168.9.10
PROBLEM: Works for this connection, but other connections are affected and no one can reach 10.1.1.20 apart from LAN and incoming traffic to F0/0.302
[code]....
But as I said before, some configurations are not supported by my device.
