Cisco Switching/Routing :: Monitor Some UPS Equipment For 2960
Feb 20, 2013
i am trying to monitor some UPS equipment,for that i am using a cisco 2960 switch and when the UPS is down it sends a L1 loop.when the switch detects the loop the int in which the UPS is conected to will get a link and go up.now my problem is this, as you probeblly know the switch has a protocol which protects it from getting loops and cuasing all kinds of problems.i need to remove this protocol and allow the switch to get L1 loops?
P.si have tryed to use UDLD, KEEPALIVE, BPDU guard, down-when-looped and errdisable commands with no success?
View 2 Replies
ADVERTISEMENT
Mar 9, 2013
A client I have just taken on wishes to provide internet data and VoIP for multiple tenants in their new office they move to in a few weeks.
they currently have a Cisco 2811 router with a 24 port Catalyst 2960 PoE managed switch serving just their staff and one tenant company who is plugged into a single port on the switch. I dont know what the tenant has the other side of that at this time.
when they move they currently will provide single port access points on the switch for each tenant, so the tenant can deal with their own network LAN. The client will provide phones to all the tenants using VoIP phones on a single subnet and hosted on an external PBX the phones all plug into the Catalyst and use the PoE. the WAN is a 20mbps fibre connection.
The client has 16 staff, the tenants are 3 companies with 3,6 and 9 staff. They may all increase or decrease in size to a total size of about 30 or 40 people.
I have a few questions
1. should I look at Vlan setup for this instead of the current basic routing setup or is that overkill since they only use one port access point per tenant as gateway.
2. can the cisco 2811 handle this or is it a bit old.
3. what router replacement would be recommended for this task given the above info especially if I went with Vlan solution.
4. any thoughts on the current switch's capability for this task.
5. managing bandwidth solutions? is there any router designed with this in mind. the ASA maybe or something like it with nice visual webgui management capabilities for monitoring and controlling bandwidth use of tenants?
Mark
View 2 Replies
View Related
Aug 29, 2012
I have some questions in regards to network equipment I want re-utilize for my distribution layer in one of my buildings.The choices at the moment are:
OPTION 1.) 2x WS-3550-12G's (HSRP)
OPTION 2.) 1x WS-6509 with cards:
What option would be better from a performance aspect? We want to have network, voice, and wireless data go through this distribution layer switch(es).This is exisiting equipment I already have and can not buy anything else at the moment.
View 2 Replies
View Related
Feb 7, 2012
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies
View Related
Feb 11, 2013
I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies
View Related
Dec 21, 2011
I have load CISCO-ENVMON-MIB and initiate walk in it but unable to find OID of Cisco 2960 temperature monitor. I have search over net and found .1.3.6.1.4.1.9.9.13.1.3.1.3.1 for temperature but this OID is not responding in this mib.
View 2 Replies
View Related
Jan 7, 2013
Which trap we need to enable to monitor FEX module on 5K.If FEX goes down due to link failure/power down we do not receive any trap on SNMP server. Ethernet1/5 is where Fex module in connected on 5K
Some sample log
2013 Jan 4 12:11:32switch1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/5 changed
its status from Connecting to Active
2013 Jan 4 12:11:32switch1 %ETH_PORT_CHANNEL-5-PORT_UP: port-channel103: Ethernet1/5 is up
2013 Jan 4 12:11:32switch1 %ETH_PORT_CHANNEL-5-FOP_CHANGED: port-channel103: first operational port changed from none to E
thernet1/5
[code]....
View 1 Replies
View Related
Dec 22, 2011
Both regular IP traffic and ICMP traffic are passing through the source port. C6509 provides the option of filtering vlan traffic during monitoring. But I don't have vlan traffic.
qa-c6509-c(config)#monitor session 1 filter ? vlan SPAN filter VLAN
So I applied an access-list which only allows icmp traffic to be sent out of the monitoring port. But it does not work.
View 4 Replies
View Related
Nov 18, 2012
I am runing 802.1x and MAB authentication of devices connected to a 3560 switch (in test). When I run 'terminal monitor' I am getting alot of authentication fail-msg. Is it possible to get the switch not to show them? I have to do some debugging on SNMP and DHCP to be able to figure out why I get these msg, but since the switch is blasting out so many auth-msg it is hard to see the debug messages. [code]
View 3 Replies
View Related
Sep 26, 2012
on 7600 SUP720 3B.I have port channel and there are two ports on that port channel. is it possible to apply this command? does it work?
View 1 Replies
View Related
Aug 20, 2012
i have just set up a monitor session with a 3750 stack .Simple enough task you would think.But i only seem to be seeing broadcast packets !!Now there is definitely unicast traffic being used on the host i am monitoring.I have done the basic commands
-monitor session 1 dest int fas 5/0/24
-monitor session 1 src int fas 5/0/34
View 1 Replies
View Related
May 24, 2012
I would like to ask about 3750 stacking and some Cat6 stuff...
1) How do we monitor 3750 stacking port in LMS?
2) Let say if I stack 3 switches, middle switch should be Master. Uplink should be at Top and Bottom. Is best practice?
3) Can we mixed 3750G and 3750X and what is result internal BW - fallback to 32Gps?
4) is there any Qos difference between WS-X6816-10G-2T and WS-X6816-10G-2TXL?
5) is there any Qos difference between MSFC5 PFC4 and MSFC5 PFC4XL?
6) What is main difference between PFC4 and PFC4XL in Sup2T?
7) Pls share more about Central and Distributed Switching in Sup2T and which card support Distributed DFCXL?
View 3 Replies
View Related
Feb 17, 2012
I was previously using SDM for our Cisco 2811, and this past week installed CISCO Configuration Professional so I could have access to a bandwidth/traffic monitor.
I have successfully started the monitoring service and monitored traffic from within CCP, but it appears that if I turn off the computer I am using to monitor the traffic, it stops collecting data until I start CCP and the monitor up again.
Is there a way (maybe with IOS console commands) that I can have the monitor always running, so I can pull up, say, a week's worth of info at any time? Leaving the computer on all the time is not an option, and currently I have only a few days of data, then a big empty chunk, and then what I have collected since I started it back up today.
View 1 Replies
View Related
Mar 6, 2013
I tried to clear monitor session on 6500 and keep on getting the following error:
%Another session parameters or permit-list is being configured %Please wait for another configuration to complete.
how i can go about clearing the monitor session.
View 9 Replies
View Related
Nov 21, 2011
I tried to clear monitor session on 6500 and keep on getting the following error:
%Another session parameters or permit-list is being configured %Please wait for another configuration to complete.
how i can go about clearing the monitor session.
View 1 Replies
View Related
Jul 17, 2012
I have 2950 switch booting through MOnitor Mode.Analyzed there is no Cisco IOS image in flash.
View 1 Replies
View Related
Mar 3, 2013
rsbd7k01-p-vdca(config)# monitor session 2
rsbd7k01-p-vdca(config-monitor)# source vlan ?
<1-3967>
rsbd7k01-p-vdca(config-monitor)# source vlan 1 - 3967
ERROR: vlan 33-3967: Number of source vlans exceeds maximum
rsbd7k01-p-vdca(config-monitor)#
View 3 Replies
View Related
Nov 15, 2011
Does one can use a Vacl to monitor network traffic on a nexus 3064 much like you can on the 6500s? If so, any performance tradeoffs or caveats to be aware of ?
View 2 Replies
View Related
Feb 6, 2013
I have 5 linux and 3 Microsoft 2008 Servers, each connected to 2 Cisco 3560 Switches. The 2 Cisco 3560 switches are connected to 2 different Cisco 515e Pix. Is it possible that if i enable Port SPAN in any of the switchport and send a copy of traffic to any of the windows 2008 server, will i be able to monitor the bandwidth of the servers (Here I am only looking for traffic going from servers to PIX and then to internet, also vice versa).
Also will wireshark be able to differentiate specify the bandwidth of each servers seperately ?
View 3 Replies
View Related
Jan 9, 2012
I have a switch 4948, with version 12.2.31.sga4 ( I dont found bug about monitor session) and we try to made port mirroring with a monitor session from a VLAN and port belong at this VLAN have traffic input and output, but in the destination port, I always see it output traffic..
Global command
Red-127#sh run | in moni
monitor session 1 source vlan 1127
[Code].....
View 3 Replies
View Related
May 20, 2013
I have cisco 2651. It contains two FastEthernet interfaces: Fa0/0, Fa0/1.Fa0/1 has an ip address. Fa0/0 hasn't an ip address.I need to create monitor session from source Fa0/1 to destination Fa0/0. Then i want to connect my notebook to Fa0/0 to analyze some traffic from port Fa0/1
View 2 Replies
View Related
Nov 5, 2012
i would like to monitor traffic between multiple source ports to multiple destination ports on a nexus 7k. i lknow when you set up monitor session is between source and destination (laptop or traffic analyser) but is there a way i can set up between source and multiple destination ports and capture that traffic ?
View 3 Replies
View Related
Aug 22, 2012
I am having difficulties with getting SPAN traffic over my WS-X6704-10GE (CFC).
CISCO7606
ios 12.2(33)SRE6, SUP720-3BXL
Trying to use the span feature, put the commands listed below in and they entered successfully, but the port is not being mirrored.
interface TenGigabitEthernet1/1
description PUBLIC
dampening
mtu 9216
ip address x.x.x.x x.x.x.x
[Code]....
View 1 Replies
View Related
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Feb 20, 2012
We have 2 6513 switches with SUP720/PFC3A and various POE modules and a 6748-GE-TX facing our servers. Additionally, we have a 4Gbps portchannel trunk interconnecting the switches. We have approximately 300 Nortel IP 1140e phones in use between the two switches.For the purpose of call recording, we've attempted to mirror the voice vlan using various approaches and have been met with limited success. We mirrored the VLAN using tx, rx, and both. When using both we appear to get duplicate packets at the destination interface.We seem to lose packets completely going in one direction or another for a given call. Packets are lost before they get to the destination interface?
View 2 Replies
View Related
Nov 21, 2012
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies
View Related
May 21, 2013
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
View 1 Replies
View Related
Nov 16, 2011
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies
View Related
Dec 26, 2012
I'm having a strange problem where I'm not able to get through a Cisco 2960-S L2 switch when connected through vpn, while LAN-WAN traffic is working fine.The situation on site is the following:When inside the network I'm able to get to the internet without a problem. The problem is within a vpn-session. When this session is succesfully started I can ping and manage the Cisco 2960-S switch, but I can't ping or manage the Dell switch from my laptop. I can however ping the Dell from the Cisco-switch. [code]
View 7 Replies
View Related
May 15, 2012
set up my QoS on two 2960
-------------------- ------- ------- ------------
PBX Asterisk |----|2960-1 |------|2960-2 |-----|Voip client2|
-------------------- ------- ------- ------------
-------------- |
[Code].....
This will be this configuration for all input interface right ? For the Output part I'm lost, what do I have to do ? And for the 2960-2 do I have to put the same configuration ?
View 5 Replies
View Related
Nov 7, 2012
we hava a couple of 2960 switches and we are logging to a syslog server. Ports keep going up and down is it normal severity (error) ?
View 2 Replies
View Related
Feb 23, 2012
We recently updated a site2site link to metro ethernet, ISP call it 100mbps LAN Extension, but to me it is just QinQ over fibre connection. Most went well, one thing (annoying to me) is we can not ping our switches on both ends anymore.
We have a 3750 in headend and another 2960 on the other end. I used to be able to ping/telnet to the management IP from one to the other. Now we can not. I think the ISP is applying some configuration on ports of their customer-premises equipments (both are Cisco switches) but agent in ISP told me no. I thought there is some configuration on Cisco switch to block "MAC discovery" but i just can not remmenber what was that and google also failed me this time.
View 3 Replies
View Related
Apr 20, 2013
I have got two links from the same ISP, primary and secondary and connected to two different switch. The ISP have passed the trunk vlan of 30, 31 and 32 on both of the links. The ISP can't provide stp. I have got another managed 2960 series switch. How can I obtain failover on switch level.
View 2 Replies
View Related
