Cisco Switching/Routing :: Route Internal VLANs On 3750X?
Apr 28, 2012
How can i route internal VLANs on a 3750X , my current network its small ( about 8 -10 subnets) so i dont wnat to add overhead using maybe dynamic protocol , My scenario is my stack of 3750X ( 2 switches) will be my CORE SW, i will have 2 stack more (2960S - 4 switches ) and it will connect to the 3750X with a trunk port etherchannel each link connected to a different switch, ( i was planning to use a L3 routing in the 3750X but not sure how it will works )
My core SW 3750X it will be connect with a firewall for aVPN , by a Layer 3 interface (using a static or dynamic protocol)
View 2 Replies
ADVERTISEMENT
Sep 5, 2012
Is this supported on a 3750X ?? A router has two VRFs and its lan interface is a trunk with 2 VLAN IDs, let say VLAN 10 and VLAN 20. The ip address subnet of these two vlans is the same (therefore , they are in different VRFs)
fa0/1
VLAN 10 = 10.15.4.9 (VRF A)
VLAN 20 = 10.15.4.10 (VRF B)
This router is connected on a 3750X switch. There is a firewall connected to this switch also, which is default gateway for several VLANs including VLAN 10 (10.15.4.1)
The goal is that VRF B ip can talk to 10.15.4.1 and VRF A can talk to 10.15.4.1 but VRF B can't talk to VRF A (10.15.4.9 <-> 10.15.4.10)
FW |--- TRUNK VLANs 1,2,3,4,10 ---------| SWITCH |----- TRUNK VLAN 10,20 -----| ROUTER (vlan 10 = VRF A, vlan 20 = VRF B)
I think this is not supported on the C3750, as my promiscuous port is located on a trunk.
View 1 Replies
View Related
Jan 25, 2012
How to get vlans working properly between sub-interfaces on a ASA and a trunk port on a switch.There seems to be issue with the VLAN's being assigned to the correct VLAN and this information being properly sent to the ASA over the trunk.
We seem to be unable to ping most of the interfaces except for one on the switch. Sometimes if we are lucky we are able to ping a host on a different vlan that is on the switch. This seems sparadic at best.
Logs on the ASA show traffic does not seem to be assigned properly to the correct sub interface. We have access rules on the ASA disallowing traffic not part of the same vlan. For example you will see networkA blocked on networkB when it really should be directed through networkA's sub interface.
Any example commands for the ASA and Switch for at least the basic requirements to enable all the VLAN's to communicate properly with the ASA?
View 5 Replies
View Related
Mar 18, 2013
I've got a 3750x stack set up as my core switch (only a small-ish environment) - I'm shortly going to be deploying an enterprise wireless network with Corporate and Guest SSID's. I'm going to be putting all traffic from the Guest SSID in VLAN 244, and don't want it to have access to any of the other VLANs (1 (Legacy Eqpt), 4, 8, 12, 16, 20, 24, 28, 32, 248 & 252).
IP ranges for all the main VLANs are:
1: 10.0.0.x/22
4: 10.0.4.x/22
8: 10.0.8.x/22
12: 10.0.12.x/22
16: 10.0.16.x/22 etc etc (you get the pattern)
I'll probably give Guest traffic (VLAN 248) the IP range 192.168.10.x/22 (not because I NEED that many addresses, but it's easier for everyone to remember/understand if I keep the subnet masks the same all round). However I also have a CCTV VLAN (252) which already has the range 192.168.0.x/24, which some people in other VLANs WILL need access to.
So my question is: What is the syntax for the ACL on my 3750x (IP base - 15.0.2) to prevent traffic from VLAN 244 gaining access to any of my other VLANs. I'm making a broad assumption here that a layer 3 switch is perfectly capable of supporting that function? I need ALL the syntax for setting up ACL's - I've never done it before
My gateway device by the way is 10.0.4.1, and I do have inter-VLAN routing set up on the core switch (obviously).
View 3 Replies
View Related
Jan 24, 2013
I am setting up a vm environment for a customer in my lab off site. I have two stacked 3750-x switches, a san, and threes UCS c220 M3S servers for hosts. I am trying to separate the lan traffic, san iscsi traffic, and san management traffic using vlans. The problem is i'm unable to communicate cross vlan with my current config, which I have attached to this post. The only noteworthy things in my conifg is that the ip route 0.0.0.0 0.0.0.0 192.168.83.6 is referring to a switch stack they have on site, that I will connect this stack to using the first two trunk ports on each switch, that I do not have here in the lab. I don't want to cause any confusion in why I have things set a certain way.
View 1 Replies
View Related
Mar 20, 2013
I have an internal DVR system that I am trying to share to the outside world. We recently put in an ASA5505 and I am having trouble getting the settings correct.I want to use an external IP to access the DVR system from anywhere and have my ASA5505 redirect the traffic to the internal IP address. I assume I need to use a NAT and a route policy however can not figure out how it would be.
View 11 Replies
View Related
Apr 14, 2013
I have 2 Vlans with seperate networks and want to create a route between one server in vlan 465 to another server in vlan 436 via port 80.Vlan 465 has a ASA 5505 inside that IP address 89.254.12.35 will be initiating the connection to address 10.200.1.213.
-Vlan 465: server address 10.200.1.213
-Vlan 436: server address 89.254.12.35
However for extended security I would like to restrict the firewall opening to an IP to IP opening.
View 7 Replies
View Related
Feb 12, 2012
i want to create a trunk between 4507 & 3945E router & route two vlans from router 3945E
4507# vlan 99 & 51
# int vlan 99
# ip add 10.22.100.1/24
#int vlan 51
# ip add 10.22.103.1/24
[code].....
4507 version : IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)
3945E: 15.1(2)T4 what I am missing?
View 3 Replies
View Related
Apr 4, 2011
I've got a cisco asa 5520 and setting up the NAT for multiple DMZs on it.
I want to use PAT on the outside interface.
internally ive created subinterfaces for the VLANs and connected to a trunk port on a switch.
configure NAT for this scenario. I've got only 1 external public IP address.
View 1 Replies
View Related
Jan 16, 2012
I used the GRE tunnel site to site VPN with 2 cisco 1841 routers. Behind one of the router R1, I used cisco ASA 5510, now my vpn is connect between two routers, but from R2 other site cannot access to LAN behind the firewall. From R1, also cannot route to local network, from local network can access to R1, I think cause of NAT . So how to configure to route internal network from R1 & R2 with VPN.
View 5 Replies
View Related
May 30, 2012
I am unable to get traffic from any VLAN to communicate outside of the router, as well as get any traffic from outside of the router to communicate with any device on either VLAN. I am able to ping the router from each device on each VLAN, and vice versa. However, the traffic seems to die at the router, and I cannot figure out why. I know it's probably a small, easy fix, but I cannot seem to find any kind of documentation on it.
View 13 Replies
View Related
Feb 17, 2013
it is possible to route netbios broadcasts between VLANs using a RV180W. Presently i have the network configured with two vlans (one for each building). The RV180 operates as a DHCP server and internet gateway for VLAN 1 and a linksys product operates as the DHCP server and internet gateway for VLAN 2.With the addition of a static route between, we can ping freely between the VLANs, transfer files, etc. However, members of VLAN 2 must be addressed by IP in windows explorer by members of VLAN 1 and vice versa. I understand this is because Netbios broadcasts are not routed between the two vlans, precluding addressing computers by name. While this is not a critical problem, it would be "nice" if i could configure the RV180 to route only Netbios between the two (still hold other broadcasts such as DHCP). I understand this ispossible on higher-end cisco products through the use of IP-Helper addresses, but I cannot find any information on doing such on the RV180.
View 3 Replies
View Related
May 30, 2011
I have ASA 5505 Firewall with security plus license, I configured two V LAN 1 and V LAN 5 as my inside V LAN for different sub net, i need to route the traffic between this two V LAN's through ASA. I configured
int vlan 1
nameif inside
Security level 100
Ip address 172.16.100.1 255.255.255.0
[Code] .........
The problem is i am not able to ping other sub net, for ex my PC is in V LAN 1 not able to ping 192.168.22.1 ... For troubleshoot i type debug icmp trace while pinging other subnet
ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4608 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=4864 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5120 len=32ICMP echo request from 192.168.22.2 to 172.16.100.101 ID=512 seq=5376 len=32
I turn off the firewall on my local machine.
View 10 Replies
View Related
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Mar 6, 2013
i cant find any difference in these two devices when i am trying to compare throughput.I need upgrade our new POP and there will be around 4900 MAC adresses in VLAN 150 and 130 MAC adresses in vlan 200.Uplink is 1 gig routed internet connection and there is 14 downlinks to separate villages.i found a few differences for eg stack interface on 3750x but i dont need it.
View 2 Replies
View Related
May 25, 2011
I have an ASA 5505 with the security plus software and I'm trying to find out how to assign 2 public IPs to the outside interface and have each IP routed to a separate internal VLAN. For example, IP 1 = X.X.X.1 routed to 192.168.1.0 and IP 2 X.X.X.2 routed to 192.168.2.0. I was told this was possible and I've been trying to find configuration examples, but I can't seem to get anywhere and now I'm getting desperate because I'm scheduled to install it this weekend.
View 1 Replies
View Related
Dec 27, 2012
I have a stack of 2 x 3750X switches these are running 12.2(55)SE5. I needed to add some static IP routes and found that the ‘ip routing’ command is not supported. I came across a document that stated “On switches running the LAN base feature, static routing on VLANs is supported only with Cisco IOS Release 12.2(58)SE and later.” So I have upgraded to 12.2(58)SE2, but ‘ip routing’ is still not a valid command.
The release notes state:“On the Cisco Catalyst 3560-X and 3750-X Series, it adds support for 16 static IPv4 routes in the LAN Base image.”
I have read other posts that talk about running the ‘sdm prefer routing’ command which I have done, but I am still unable to add any routes or run the ‘ip routing’ command.
View 4 Replies
View Related
Dec 9, 2012
I have an 1811 with several subnets connected to it.I recently installed a 3750x plant and want to bring my interior routing back to it.
All the routing is handled by the 1811 via secondary interfaces on vlan1?
I have 192 ports, and subnets show up on almost all of them. None of the ports are assigned to any specific vlans. Most ports have several subnets on them.
What is the best approach to getting the 3750x to handle the routing?
View 18 Replies
View Related
Jul 31, 2011
I purchased a WAP4410n for our small office to provide wireless access to our internal network to laptop users. I have configured the device as simplistically as is possible, but although I can get my laptop to connect to the AP (verified by managing the device wirelessly as well as by pinging the IP address) I can not get to any other IP address on my internal network nor the internet.I gave the device a static IP address - 192.168.1.50 subnet 255.255.255.0 with a default gateway of 192.168.1.254 which is my 2811 router. I set up a WPA-secured SSID.
A second problem I have is that if I set up my laptop wireless card to get its' IP settings form a DHCP server, it picks up a 169.xx.xx.xx ip address - it is as if the AP is not passing my DHCP broadcast / response through.
View 6 Replies
View Related
May 22, 2013
my company pay a switch 3750 X. WS-C3750X-24T-E. It uses IP services basically but I failed to configure InterVLAN routing. why interVLAN routing doesn't work on my switch?
View 10 Replies
View Related
Mar 28, 2012
Why does my 3750x-12s switch say it's not supported in CNA??? I upgraded to CNA 5.7.1 and still says unsupported. This device is supported or I'm just missing something.I use CNA heavily to manage our MANY vlans.
View 1 Replies
View Related
Mar 4, 2013
I want to confirm this is a licensing issue. On a 3750X with ipbase, I cannot create a vrf. So I would need the universal image, and that is a seperate license, correct?Is there a link that describes the difference bewteen ipbase and univeral images?
View 6 Replies
View Related
May 22, 2013
I have a query regarding attached Network Design
PC---2960---3750(One Routed Port and All Switched Port)------------------------ 3750(One Routed Port and All Switched Port)-----2960------Internet
I have many Vlans on left side of image , Right Side of Image is having internet connection via Modem, and local connectivity between VLAN works fine but Other Vlans Except Vlan1 is able to Access Internet.Note that 3750X did not have NAT Feature ,How should I able to get Internet on Other Vlans (10,20)
View 4 Replies
View Related
Jan 5, 2013
scenario A
A site .
PBX --->
Data ---> other brand router ----> 3750X ---> wan
[Code]....
How to know whether QoS work on the 3750X or not ? Is it correct about the config in scenario A ?
View 2 Replies
View Related
Feb 3, 2013
I have a one question. I am using Cat3750x-48 switch. Suddenly it has occurred following high CPU log message in Cat3750x-48 switch.
%SYS-1-CPURISINGTHRESHOLD: Threshold: Total CPU Utilization(Total/Intr): 62%/0%, Top 3 processes(Pid/Util): 162/40%, 156/10%, 74/1%
What is meaning of PID 162 ?
View 1 Replies
View Related
Jan 1, 2013
There seems to be a lot of conflicting information on what can and can't stack together in the 3750X range.
I know that LAN Base can only stack with other LAN Base switches.
Can IP Base stack with IP services in 3750X? I have also heard that the 15.x.x IOS restricts mixed feature set stacks?
I know that Cisco recommends that all switches in a stack have the same IOS and feature set but having all IP Services in a stack can get too expensive.
View 6 Replies
View Related
May 7, 2013
I'm trying to review a QoS setup, and I'd like to make sure I fully understand the current setup before I change anything. I'm seeing output drops on two different queue-thresholds, but not sure how packets are making it to one of the queues.
Switch Version
CORE#show ver
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.0(2)SE, RELEASE SOFTWARE (fc1)
System image file is "flash:/c3750e-universalk9-mz.150-2.SE/c3750e-universalk9-mz.150-2.SE.bin"
cisco WS-C3750X-24 (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Switch Ports Model SW Version(code)
I can find queue4-threshold3 in the mappings, but how are packets getting mapped to queue2-threshold1? The priority queue is disabled for this interface, so I'm not sure how this queue is dropping packets, according to the maps nothing is mapped to 02-01.
View 3 Replies
View Related
Mar 21, 2013
I am building a switch stack using 4 48 port 3750X switches that will also have the power stacked. If I install a single 715W power supply in each switch will the stack support 802.3af accross all 48 ports on each switch? My calculations are 48 ports x 15.4W which gives me almost 740W needed which is over hte 715W power supply. I was reading somewhere were it mentioned that in a powerstack additional power can be drawn from the stack. I know this will not work if you are trying to support power on all switches accross all ports but would it if say 2 of the 4 switches are needing to provide PoE accross all 48 ports? If I say we can only use 24 ports per switch for PoE that drops the power need down to 370W which I believe should work. Just trying to get a better understanding of PoE consumption. Would the best solution be to just add a second power supply to each switch?
View 8 Replies
View Related
Dec 19, 2011
I am implementing a guest wireless network to work alongside my internal network. The guest network will use the existing switching network and will be separated by VLANs. I have the ASA set so that traffic can get to it and out to the Internet. I can set up a workstation on the same VLAN as my guest network and can route inside my network (strictly doing this for testing purposes). Where I am having problems is with the Catalyst 4506 switches and the ip routing. I had two separate "ip route" statements defined on my switches.
ip route 10.200.2.0 255.255.255.0 10.200.2.254
ip route 0.0.0.0 0.0.0.0 10.100.100.254
I have discovered that the traffic is always following the default route despite the fact that my IP address on my test workstation falls in the 10.200.2.x network. I was looking at documentation and found that it is possible to set up policy-based routing on the core switches. Can you have two "ip route" statements defined like this to segreate traffic or do I have to use PBR for routing (or a combination) in this case? If I define PBR then how does that impact my existing routing? I need to make sure that I can still route the existing traffic while I'm configuring this change.
View 9 Replies
View Related
Jul 4, 2012
upgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies
View Related
Jan 23, 2013
I have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]
View 5 Replies
View Related
Mar 27, 2012
I have purchased these two switches from ebay as a test lab, I plan to connect them up via a gigastack modulecable and enable ip routing on the c3550 and vlans to talk to each other.
I'm very much a procurve person and really need to get into the cisco switching.I will want to trunklacp between the switches - whats the process is setting that up on cisco switches?
View 1 Replies
View Related
Feb 19, 2012
I have a 3560E with 2 vlans that I want to route between. one device with 2 vlans and route between.Interfaces are configured as such:
int g0/11
switchport mode access
switchport access vlan 10
int g0/12
switchport mode access
switchport access vlan 11
[code]...
Laptops on each port with 10.10.10.2 and 10.10.11.2 configured on them. I can ping from 10.10.10.2 to 10.10.11.1, but not to 10.10.11.2.What do I have to configure to be able to get the 2 laptops to talk to each other?
View 9 Replies
View Related
