Device: Cisco ISR 1811
IOS: 15.1(4)M5 Advanced IP Services
I seem to be unable to access any IKEv2 features. The command crypto ikev2 is not available. Everything I've read suggests IKEv2 is available in this IOS version.Is there something I'm missing?
I just picked up an e3000 last night. Set up was performed manually. Flashed to 1.0.04. No issues and I was up in under 10 min.Although I read the user guide, prior to purchase, I admit I did not expect that I would not be able to configure ALL of the router's features and functions from the web based configuration, without using the CISCO Connect CD.Parental Controls and GUEST Access cannot be configured unless you load the Cisco Connect software.While this is not a huge deal, this implementation is clumsy and cumbersome for advanced users. Honestly, I had no disire to install the Cisco Connect software. I was further disappointed to see that it stores the router's password.
My feeling here, let's not ruin a great thing. There are two types of users. One's who need a configuration wizard, and other's who don't. I guess some inroads are being made in the right direction as some GUEST access functions can be made in the web gui on the e4200. I hope this can be further expanded to all "e" series routers in the future. Overall, it works as advertised. Streaming 720p HD video over wireless 2.4Ghz band G only is flawless. This is no different than my wrt54g2, but I'm upgrading to a 1080p player and have read that N on the 5Ghz band is the way to go.
I got a Cisco 1811, with on FA0 ( WAN ) acting as a dhcp client and on FA1 ( LAN ) my laptop wich is getting a address form the DHCP Pool.
I receive a ip address on my laptop but it doesn't know the way to get outside.
here is my config:
Building configuration...
Current configuration : 3498 bytes
!
version 12.4
[code]....
I'm trying to configure a Cisco router 1811 for Internet access, so here's my scenario:
2 ISP:
1º - 66.110.117.33
2º - 64.30.154.81
Internal Server:
172.16.30.2
how can I make all this traffic(SMTP,pop3,http,HTTPS,DNS) available in both interface?
I've enabled Cisco "Anyconnect Premium Peers" for client less ssl vpn connections, the obvious catch is that for ikev2 Anyconnect sessions it wants to use up the SSL license pool instead of the IPSEC pool (which I have lots of connection licenses for "Total VPN Peers : 250".
* Is there any way to configure Anyconnect to connect via IPSEC and use an IPSEC license (while keeping the Anyconnect Premium Peers enabled)?
* Do I have to consider 3rd party vpn clients, outside Anyconnect?
I've ASA 5520 with 8.4(3) running.I want to set up VPN remote access using following document url...I managed to get a connection running, but when I check the connection on the ASA, it shows as a SSL-tunnel, not an IKEv2 tunnel.How can I assure I have an IKEv2 tunnel instead of a SSL tunnel ?Can I do with annyconnect same kind of connections I used to do with the Cisco VPN client for IPSEC?
View 4 Replies View RelatedI have been working for a while trying to get the Linux AnyConnect Client to Connect to the ASA using IKEV2 and EC Certs. I have gotten it to work with SSL, but I can't seem to figure out how to get IKEV2 turned on. On the profile screen (attached) in the ASA when I check IKEV2 I get the cert screen, I check the cert, but then it fails to bring the cert and unchecks the block. The Network Design is simple. ASA IP on high side (outside) 172.20.206.8 with the client at 172.20.206.50. Local LAN is at 10.200.203.0/24.
View 7 Replies View RelatedIf I implement IKE V2 on Cisco ASR 1006 Router or on firewall and sets up IPsec with IKEv1 device ( Cisco Router , Juniper etc )will it work or not ?
View 6 Replies View RelatedWe are testing the AnyConnect VPN Client to replace legacy IPSec VPN Client 5.0.x. We could setup the connections with SSL and IPSec (IKE v2).Now we have to decide which ist the better method.
View 1 Replies View Relatedi have a little 877 router running Version 12.4(24)T2. I want to muck around with an IKEv2 IPSec VPN but i can't find anywhere to configure IKEv2.
I have found some doco that says its under the crypto config, something like router(config)# crypto ike2 ...........
But i don't have that option. Is it anywhere else?
I have a L2L tunnel setup between two ASA's (v8.4). I used the wizard to set these up and selected the defaults of both IKEv1 and IKEv2, thinking that it would select one or the other. The strange thing is that now I see a separate session between these ASA's, one for IKEv1 and one for IKEv2. Both are passing traffic. Is this expected behavior? Should I disable IKEv1 to force only v2 since both are v8.
View 5 Replies View RelatedRouter ios for c3600, c7200, c2600 that support ikev2? (command crypto ikev2 )
View 5 Replies View RelatedI have a cisco 1841 router and want to run BFD i think it needs IOS 12.4T..It has currently 12.4 but no T does the "T" IOS have mroe features?
View 1 Replies View RelatedNCM is going away. It is recommend to move to LMS. We already have a LMS deployment. Currently just used for Monitoring/Performance.Trying to figure out how to get the Configuration change piece that we used NCM for into LMS. Not really having any luck.What I am really wanting to do is configuration archive, device config change notices (when a device config changes I can run report to see who and what was changed), and configuration comparisions (between old and new configs)
View 5 Replies View RelatedNeed to understand some features of Cisco Small Business 300 Series Managed Switches. one of this is "Static routing/Layer 3 IP routing between V LAN's allows for communicating across V LAN's without degrading application performance" what is this means can i create V LAN or just V LAN can pass through this kind of switch? how about this features from Cisco Catalyst 2960 Series Switches " The ability to set up virtual LAN's so employees are connected by organizational functions, project teams, or applications rather than on a physical or geographical basis" what is the difference of this features of this different model of switches?
View 3 Replies View RelatedI just purchased a SA 520 and I am trying out the IPS feature before I buy. During my tests I get around 85 Mbps off a 100 Mbps connection (which is relatively normal), however as soon as I enable IPS with very few options (Trojan/virus, HTTP, etc), it drops down to 18 or so. Anyway to improve this?
View 14 Replies View RelatedI wish to use a 1921/k9 as a router on a stick. Inside interface interconnects up to 9 VLAN, and performs the routing. Does the 1921/k9 supports trunking and VLANs (I think it should support 16 VLAN, but I am not shure) or I should choose 1921-SEC-k9? Routing performance is the same both on 1921/k9 and 1921-SEC-k9? (I think I'll use static routes or RIP, it is not a large network)
View 1 Replies View RelatedI'm trying to secure my dir-615 and I can get in to the web site but the connection wizard is greyed out and the manual set-up is alos greyed out even though I can select manual set up?
View 2 Replies View RelatedI have 2 ASA5505's connected through a site-to-site using IKEv1 and IKEv2.Recently, I ran through the wizard to configure the AnyConnect software. [code]Now, my site-to-site connection will only come up using IKEv1.Is there a way to have both the Site-to-Site and the AnyConnect VPN connections use IKEv2?
View 1 Replies View Relatedhow to configure a site to site tunnel using IKEv2 between our offices using an ASA 5515-X and a Cisco 3925 router running IOS 15.2 Connecting ASA to ASA and ASA to Router via IKEv1 works fine. Want to take advantage of the improvements in IKEv2 but I'm having difficulty with the ikev2 setup on the router. Here is the pertinent ASA side config--
ASA IP: 5.5.5.5
Router IP: 10.10.10.10
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1
[Code].....
I am doing a security assessment of an organization that uses 871/881 routers with the firewall features enabled. I see the following commands defining packet inspection done by the firewall software.
-ip inspect name inet-users tcp
-ip inspect name inet-users udp
-ip inspect name inet-users icmp
What I am trying to define is the inspect name "inet-users". It is obviously a constant defined by IOS as it is not defined anywhere in the configuration file like any other "variable" and does not generate an error.What does "inet-users" define? I'm assuming it is all users using the interface(s) where the inspect commands are used, but is that correct? The Cisco IOS manuals do not contain a reference to "inet-users" hence why I'm here asking.
We just replaced a floor swithc, and ended up going with an IOS-XE software, LMS does not seem to like this software, the device is not available in my Identity dashboard, it's abviously running dot1x.
LMS shows it as software version 03.02.01.SG, same as you get when you do a show version, license level is enterprise services.
Actual Image name: cat4500e-universalk9.SPA.03.02.01.SG.150-2.SG1.bin
Also, the IOS upgrade option does not work for this device, it give an error saying to perform an inventory collection, which I have manually performed, the device is reachable and manageable by LMS, and it does not show up in any of the IOS version reports.
My current network setup has pix 525 firewall and for IDS i have 4215 box.As the utilization is high i am buying new ASA5520 firewall.
My query is
1 My IDS is end of support should i buy an IPS moudle with the asa 5520.is it recommended?
2 Other than firewalling what are the default features supported in asa 5520 like vpn,content filtering etc.
Is that possible to only use ikev2 for two 5505 ASA site to site VPN. Any advantage and disadvantage?
View 3 Replies View RelatedI can not connect to the web features when plugged in the router but works fine when plugged in the modem directly.
View 1 Replies View RelatedI am trying to stack the following -
3750G 12S - 12.2.53(SE2 IP Services) Running EIGRP & OSPF
with
3x 3750X 48P-S - 12.2.53(SE2 IP Base License)
Doing some research, the IP Base does EIGRP on the 3750X, does it do OSPF?
If not I will have to get licence for the 3750X?
I am planning to get the following Hardware;AIR-CT5508-50-K9 5508 Series Controller for up to 50 APs AIR-LAP1262N-E-K9 802.11a/g/n Ctrlr-based AP; Ext Ant; E Reg Domain..During my design, i am considering to get the following security features.I don't have WCS and Mobility Services Engine (MSE). Managing Access Points at remote/WAN office.wIPS configuration (without WCS and MSE)How Rouge APs will be detected and Prevented. Can Automated prevention be implemented.Is wIPS (with WLC 5508) support to detect and prevent Rouge AP.Is Proxy Redirection supported on WLC so that the traffic from Wireless clients will automatically be redirected to Proxy (without adding the proxy in explorers of Wireless Clients).
View 7 Replies View Relatedis there a way to verify how much licensed features are used?If the usage is far or near to the limit?
View 4 Replies View RelatedAfter configuring the router and enabling a load of functions to secure our LAN, the download speed halved! Even disabling AcitveX "eats" 10Mbs! I understand that enabling IPsec will drag the speed down to 25Mbps, but I have disabled this.
Even setting the QoS to speeds equal or higher then the ISP's promissises drags the speed down!
Will ACE 4710 support for IPS features?
View 1 Replies View RelatedI would like to configure the policy base routing (PBR) on router (3900) base on the "specific tcp port" (TCP port 16255) to re-direct the traffic to another FE port.
From cisco web portal, CAT 4500 should support PBR as below:"Policies can be based on IP address, port numbers, or protocols. For a simple policy, use any one of these descriptors; for a complicated policy, use all of them." url...
Does 3900 router has the same features on the PBR? if yes, can it support "source tcp port" and/or "destination TCP port"?
We just purchased a bunch of 3750s, and we need to do EIGRP stub routing and VRF routing
For the newer IOS versions (15+), will I need activation keys?
using the 55xx as a L3 Distribution switch or even as a Core. By enabling the L3 features does it allow you enabled L3 SVI's for VLAN interfaces or are there interfaces on the daughter card that are used for routing instead?
View 5 Replies View Related