So we've setup an ASA 5510 and users can VPN in no problem, and an IPCONFIG /ALL confirms that the DNS server settings from the group policy have been applied.Group policy sets DNS servers as 192.168.2.8 (internal), 8.8.8.8 (google). Public internet sites work ok.Typing nslookup opens up on the correct internet DNS server, but all requests timeout.
View 6 RepliesI have a pentium 4 pc and another Dell 5110 laptop have also 1 network wire i can connect either the pc or the lap and network is manual ip configuration my ip is ...,...,...,5I usually use PC with xp operating system ( working fine )but when i use the laptop it is always gives me ( unidentified network / limited connection )even the pc works fine ( i have just try it the moment before ).
View 5 Replies View RelatedI'm trying to connect this printer:
HP 5110 OfficeJet
HP Officejet 5500 All-in-One series overview - HP Small & Medium Business products
for access to anyone that wants to print. There are about 7 PC's and I bought a USB to Ethernet adapter so it plugs from the back of the printer and into the Ethernet port on the router.I am trying to access it from a Mac OSX 10.5 computer and 2 Windows PC's...
my new dell 5110 recognize my Nokia Bluetooth headset BH-105, but windows 7 asking me for the driver, and there is no software comes with the headset.
View 2 Replies View Relatedhow i can install wifi software on my dell laptop 5110
View 1 Replies View Relatedi`m having a dell inspiron N 5110 i7 and i cant connect to internet at all. i think i`m missing some drivers for network adapter and bluetooth also not working?
operating system:windows 7 32 bit
I just got a new Inspiron 5110 laptop. I can connect to internet via wireless but I cannot get internet via my cable provider. It works on my old desk top. Does something new to be re configured??
View 1 Replies View RelatedI HAVE INSPIRON N5110 i-5 processor 2430M operating system window 7 i am not able to connect to internet through ethernet cable the following are the steps which i have taken when i am creating a new connection it is showing unable to create.
View 9 Replies View RelatedI was asked to block pings from the internet to the outside interface of our ASA-5505 firewall. I found a post that said to enter "icmp deny any outside", however that does not do it.
I created an ACL to try and do the trick, also to no avail:
access-list outside_in extended permit icmp any any echo-reply
access-list outside_in in interface outside
access-group outside_in in interface outside
I'm looking for troubleshooting LMS 3.2.1 and the ping/ICMP traffic it transmits.A lot of my devices are receiving a lot more pings from LMS than I would have anticipated.I don't run PING sweeps in Device Discovery or CM-UT. I've even disabled DFM polling in a hope to trace the source of these PINGs. Any list of which modules use PINGs so I can turn them off and track down the offender.I really only want to manage the known devices I already have via SNMP alone. I don't require LMS to be PINGing for discovery or reachability purposes.
View 4 Replies View RelatedI have two cisco asa firewalls connected through a VPN, one is 5505 and the other is a 5510. From the 5505 I can ping the internal interface of the 5510, but not vice versa. Would that be a NAT issue? I used the ASDM to configure the VPN tunnels with the wizard for IPsec site to site.
View 3 Replies View RelatedIn the new firmware version is there a way to turn off or not allow anyone to ping my router by blocking any private type of IP address? Which also include loopback addresses?
View 1 Replies View RelatedI have recently installed a new Cisco SG 300-10 switch--running in layer 3 mode--to function as a basic router for a new subnet installed at one of my company sites. When we attempt to ping devices on the 15.120.204.0 subnet from the 230.20.1.0 subnet, each device gives 2 responses and then times out continuously after that. If we wait long enough (thus far, an undetermined period of time) and reattempt to ping the same devices, the same thing occurs. Otherwise, we get nothing but timeouts. This occurs regardless of where we connect in the 230.20.1.0 subnet including VLAN1 on the SG 300-10. However, if we connect into VLAN 2 on the switch and assign a static IP, those same devices respond continuously. I was thinking that this must be a security setting of some kind but I'm unable to locate anything in the SG 300-10 that would appear to cause this.
View 1 Replies View RelatedI was asked to block pings from the internet to the outside interface of our ASA-5505 firewall. I found a post that said to enter "icmp deny any outside", however that does not do it.
I created an ACL to try and do the trick, also to no avail:
access-list outside_in extended permit icmp any any echo-reply
access-list outside_in in interface outside
access-group outside_in in interface outside
I'm trying to set up an 802.1 q trunk between my layer 3 switch and ASA5520. I understand I need to create a subinterface to accomplish this and have done so. However, the subinterface does not respond to pings, and when I attempt to run the packet tracer on the firewall itself, I get a message saying Flow is denied by configured rule. But the strange thing is it shows the output interface as "np identity ifc":
(The VLAN in question is VLAN2 192.168.2.3 is the VLAN2 address on the switch). The ASA config is as follows:
ASA Version 8.2(5) <context>
hostname context2
names
!
interface GigabitEthernet0/0.2
nameif Inside0/0.2
[Code] ....
I'm having an issue that I can't quite understand. I set up a test lab to get familiar with EIGRP routing. I have a Cisco 3845-MB with 2 VWIC2-2MFT-T1/E1 cards.sh ip int brief shows UP UP status on all serial ports. I gave it an IP address but I'm having trouble pinging the serial interface IP. It's dropping pings to its own S 1/1/0 interface when pinging from console. I have known good T1 crossover cables 1&2 - 4&5.
Here is the "ip int brief" from 3845-MB
3845-MB#sh ip int brief
Interface IP-Address OK? Method Status Prot
ocol
GigabitEthernet0/0 unassigned YES NVRAM administratively down down
GigabitEthernet0/1 172.30.2.1 YES NVRAM up up
Serial1/1/0:0 10.3.29.2 YES manual up up
Right now it's pinging itself at about 60 -90% success rate... and I can't figure out why it's dropping any packets at all. I have other issues with in the lab as well... but i think this might be my "core" issue.To make matters even more "weird" I've tried two different VWIC2-2MFT-T1/E1 cards and I drop pings with both of them.
Here is a sh run and a sh diag:
3845-MB#sh run
Building configuration...
Current configuration : 1434 bytes
!
version 12.4
service timestamps debug datetime msec
[code].....
Now there is an issue that I don't really know how to deal with it and its the multiplayer games ping that I get lately , its about 3 months that I get very high pings when connecting online to a multiplayer server , no matter which game it is , the same happens.
I was getting around 380-470 ping while playing on an European server , but then we solved my last problem (The someone that was connected to my home network) and it reduced the ping to something around 250-300 (sometimes it drops to 100-120).
It is still very high , 3 months ago I had a real bad internet connection and when I was playing on European server's I was getting a stable ping of 100-120 that was normal !
A friend of mine got the same connection that I have and he gets a ping of 100-120 and we play on the same servers (same ISP too).
How can I know where the problems come from ? I did move to a new house in a new area , maybe the ISP server's over there are weak and over loaded ? Because when its like 02.00 AM I am getting a stable ping of 100-120 . What is going on here ? Is there a possibility to ask the ISP to move my connection to another area servers or something like that ?
I've just purchased WRVS4400N VPN router and installed it. This was a replacement of a old Linksys router. After installing the router, I've started seeing wireless drops, packet drops and latency on pings. I've installed the latest firmware, disabled Firewall services, disabled IPS. No changes at all. As a basic example, I am pinging my NAS device (hard wired to router) from a laptop connected to wireless below. Previously while connected to my old linksys router the time was equal to no more than 2ms.
View 4 Replies View RelatedSo because of the way active directory handles Group Policy I have been tasked with finding out why this is failing over the WAN. Basically I know why, but don't know how to correct it. I am trying to increase the MTU over an ipsec tunnel to 2048 to allow Microsoft Slowlink detection to occur. [URL] Basically, it sends 2 icmp packets. One at a normal size and one at a size of 2048. In my case this is trying to occur over an ipsec tunnel and failing due to the MTU being at 1440. I have seen a few articles about increasing it to 1500, but is there a way to increase the MTU to allow the 2048 sized icmp packets?
View 4 Replies View RelatedI have a WRVS4400N router in a remote office. I have connectivity to the office and computers there. But the web interface for the router is failing to come up. This happens once every few days or so. Is there any utility or something that I can use to remotely reset the router without making use of the webinterface or having physical access to the router?
View 4 Replies View RelatedAfter hours of trial and error, and searching user groups, I have found that on occasion, ASA v8.4 will stop pings with the IPsec-Spoofing logic. Interestingly, the packet-trace will say everything is allowed.
The fix (at least in my case, and one other) is to narrow the crypto-map to specific hosts, not subnets.
I have a d-link dslg604t, i tried to do the frimware upgrade and it froze in the process. Now the internet doesn't work at all. I have uninstalled the drivers, reset the modem and it indicates the modem is working as in i have the two monitors and the blue flashing light between them shown, also all the network settings are there. DHCP is assigned automatically etc etc. I can ping the modem but when i try to connect to the internet i get "detecting proxy server", "internet explorer cannot display the page". "FTP (passive)- Error 12007 connecting to ftp microsoft.com
View 1 Replies View RelatedI am purchasing a new DIR 600. It pings properly, but didn't access internet. I am using HP Desktop and ORTEL broadband connection.
View 1 Replies View RelatedUsing a WRT310N Linksys Router and just today at 2PM I received the largest and longest lag spike ever, it is still going on as I write this (10:00PM). I am receiving pings of 500+ ping and my download speed spikes like crazy. Here are my speedtest.net results.Here are my results from Netalyzr URL
View 4 Replies View RelatedXP Home edition, went to tools can't find working off line or working online to make sure off line is not checked so I can get on line DSL Verizon , Wireless router, wireless switch in on, on the cpu
View 1 Replies View RelatedASUS Notebook G60Vx Series
Windows 7 Home Premium 64-bit
Intel(R) WiFi Link 5100 AGN
A few days ago my internet suddenly stopped working. I plugged in the ethernet cord and everything worked fine. Checking the properties in the device manager showed the device was working properly, I also tried resetting it to make sure it was enabled but it did not work.
Upon troubleshooting, the "Windows Network Diagnostic" said the problems was that the Wireless adapter was not turned on. Using the switch on the front of the laptop as well as the function keys does nothing. Usually a graphic pops up showing if the WiFi is on or off, changinging transparent to show the WiFi is disabled. Now when I turn the switch on it always appears transparent, effectively going from off to off
So I know the computer reads both the function keys and the switch on the front but both methods never actually turns the adapter on. I just finished a system restore and nothing has changed
Today, while surfing the web my internet connection on my PC just randomly shuts off. I go check on my laptop and its normal. My WiFi says that I am connected to an Unidentified network with no internet access. So i got frustrated and checked all the forums and nothing seemed to work. So i restored my computer to factory settings and I still got this problem. Does this mean my Wifi Card is bad? Is it a virus? I can see other networks fine but i just cant connect to mine!
View 8 Replies View RelatedI need to know if I'm right about this. I have a customer that wants me to set up a dynamic-to-static IPsec tunnel between an 1811 router (dynamic) and an ASA with a static address.The catch is that the 1811 sits behind an ISPs cable modem where it picks up a private 192.168.x.x address.
Is there any other way to make this work where the router with the dynamic IP is sitting behind a box that's doing PAT translations?
I've recently been tasked with providing access to several internal servers to a remote site via one of our ASAs. In order to keep things simple, I have begun by creating a single static NAT rule for one of the servers. The Site-to-Site VPN connection profile was then created and testing has begun. Unfortunately it looks as though the NAT rule isn't working. As I monitor the tunnel, I still see our internal number being broadcasted and not the mapped address, which prevents the tunnel from being established. The remote site has verified that this is what they are seeing too.
Appliance:
ASA 5510
ASA 8.4(2)
ASDM 6.4(5)
Address Legend:
(Note: The following addresses are not actual addresses.)
[Code]...
I have been trying to get my FTP server working for months with no joy. It works when I connect to it internally but not from outside. If I do a port scan, I can see that port 21 is open. I tried it with disabled firewalls and also checked with ISP that nothing is being blocked. I have attached the config file. I used several differnet FTP servers such as CoreFTP, Wing FTP etc.
View 13 Replies View Relatedwhy the following configuration is not working? I have two clustered ASAs inline from one another, in front of a 4506-E switch in front of a host I want to access via RDP, like so: My issue at this stage lies with getting the UNTRUST firewall configured. I've tried the following configuration 1) Creating the host.
View 13 Replies View RelatedI am trying to use a Dell FTRJ8519P1BNL SFP fiber module in a Cisco Catalyst 3560 and have already run these commands: no errdisable detect cause gbic-invalid service unsupported-transceiver.But I STILL am getting these errors even after shut/no shut on the port.
View 19 Replies View RelatedI am have unabled the cisco SDM on my pc, and able to get the http for my router 1841:I have done below configuraiton in my R1841[code] why I am not able to get the above commands, and does my SDM not work due to this or anything else need to be done?
View 4 Replies View Related