Cisco VPN :: ASA505 Establish IPSec Between Office And Another External Site
Dec 29, 2011
We have to configure our firewall cisco Asa 505 (ASA Version 8.3(1)) in order to establish a ipsec vpn between our office site and another external site. Vpn has been established successfully between our ip site 172.16.69.24 and other vpn ip site 172.16.23.23.Our server (192.168.100.25) behind firewall cisco (sk lan 192.168.100.254) manages to ping server 172.16.23.23 on other site through a static route add on windows so server (route add 172.16.23.0 MAK 255.255.255.0 192.168.100.254).On the other site, server with ip 172.16.23.23 doesn't ping our vpn ip site (172.16.69.24) which has to be natted to our server 192.168.100.25.
View 2 Replies
ADVERTISEMENT
Feb 17, 2013
We have configured a site to site tunnel from our ASA to another organizations Cisco 3030. It appears to have just one way initiation. We can do a ping to a device on the remote site and it will ping just fine. however, when the tunnel needs to be initiated from the remote site, it will not work until we have initiated the tunnel and then everything works.
I continue to see Error processing payload: Payload ID: 1 errors on the ASDM logs.It appears that all the configuration is in place because we can in fact establish the IPSec tunnel unidirectional. And once established, traffic can flow bidirectional.
View 1 Replies
View Related
Dec 19, 2011
As you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
View 10 Replies
View Related
Nov 13, 2011
our customer unfortunately uses a Watchguard.Finally we could establish a site-to-site vpn connection.To test if the connection re-establish again, we cleared our vpn session by "clear crypto isakmp <session id>" and after that "clear crypto sa <ip address of the peer>"After that, the session is down on our site, but the watchguard keeps the Phase I still up, either the deleting messages from our cisco are visible in the watchguard log files.Watchguard helpdesk told us, that the messages are only seen as a deletion message for Phase II, therefore Watchguard keeps Phase I up and running.Here you could see the cisco 7206 log messages aftre the clear commands:
: Nov 10 13:22:06.508 MEZ: IPSEC(delete_sa): deleting SA,
2011-11-10 13:22:06 Local7.Debug 649460013: : (sa) sa_dest= <local peer>, sa_proto= 50,
2011-11-10 13:22:06 Local7.Debug 649460014: : sa_spi= 0xEB0AE65A(3943360090),
2011-11-10 13:22:06 Local7.Debug 649460015: : sa_trans= esp-aes 192 esp-sha-hmac , sa_conn_id= 669,
2011-11-10 13:22:06 Local7.Debug 649460016: : (identity) local= <peer>, remote= <peer>
[code]....
In my opinion, it looks ok and we do not have problems with other VPN devices with this kind of tests.what could be done that the watchguard deletes Phase I, too? Or that an explicit Phase I deletion message is created and sent by our cisco 7206?
View 3 Replies
View Related
Dec 27, 2012
Last week, I was able to establish a site-to-site VPN tunnel between an ASA 5505 and Cisco C881 router just fine. The tunnel was up and and running for a number of days but today the tunnel is no longer up. I was wondering how, if there are any commands to re-establish or re-initiate the tunnel.
View 3 Replies
View Related
Jul 26, 2011
I'm trying to establish site to site VPN between ASA5510 to ASA5520, scenario. [code] our Vendor said to nat the local network to specific ip and use that ip as local pool,here the configuration details [code] i create static nat but its doesn't work for me phase 1 is not up, how to create nat local network to 10.10.10.10.
View 9 Replies
View Related
Sep 3, 2012
I'm trying to establish a site to site VPN using ipsec between an RV220W in the UK and an RV042 in Italy to no avail.The RV042 tells me it's "waiting for a connection" and it gives 0.0.0.0 as the remote address (i'm using Dynamic addressing at both ends). I can ping the remote address with a response.The basic parameters I'm using is 3DES with SHA1, but the RV042 offers an option for Perfect Forward Secrecy which the RV220W does not (I've tried toggling this) and the RV220W offers and Extended Authentication mode which I can't see on the RV042.
View 2 Replies
View Related
Jul 29, 2012
It is required to setup site to site vpn between cisco 7200 and checkpoint firewall.But tunnel won't establish and following error occured. It's difficult to troubleshoot because other end managed by different party. In our side udp port 500 opened.
View 8 Replies
View Related
Mar 6, 2013
Our Headquarter (asa 5510) is running a site to site vpn connection with a Branch office (router 2811). All remote users are accesing the internet through the VPN and also accesing headquarter file servers.I want to know if there is a way for some remote users to be able to use the vpn for accesing the file servers but to access the internet through the branch office. The rest of the remote users will be still accessing the internet through VPN.
View 2 Replies
View Related
Jul 15, 2012
we have two ASA 5510s one in 8.4(4) and one in 8.2(5) in a site-to-site VPN setup. All internal traffic is working smoothly.Site/Subnet A: 192.160.0.0 - local (8.4(4)) Site/Subnet B: 192.260.0.0 - remote (8.2(5)) VPN Users: 192.160.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible.
Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise.There are also some weird NAT rules that I am not happy with that were created after I upgraded Site A ASA to 8.4
Site A internal: 192.160.x.x External: 55.55.555.201(main)/202(mail)
Site B (over site-to-site) is 192.260.x.x External: 66.66.666.54(all)
I pretty much just have the basic NAT rules for VPN, Email, Internet and the site-to-site.What do I need to add for the VPN to be able to access the site-to-site network?
Here is my NAT config:
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static VPN_Network VPN_Network no-proxy-arp route-lookup
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static DOMAIN_REMOTE DOMAIN_REMOTE no-proxy-arp route-lookup
!
object network DMZ_Network
nat (DMZ,Outside) dynamic interface
object network DOMAIN_LOCAL
[code]....
View 3 Replies
View Related
Jul 23, 2012
I want to implement site to site vpn among our Head Office and Barnch routers (300 Sites).Head Office Site I have a cisco 7200 Router Im going to terminate the VPN conection on that.Branches we are having cisco 1841 series routers. They all are capable of working with VPN.In the present it is act like a EazyVPN Server for selected sites(30 sites).Is there any license limitations in Cisco 7200 Router ?Can I run both Site to site VPN and Eazy VPN Server together ?
View 1 Replies
View Related
Feb 23, 2012
I am try to setup my office network to able to connect to one of my customer HQ via site to site VPN. I am using Cisco 1841 router to do the job.
The problem that I am facing now is no able to connect my other PC in office to the remote site.
show crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst src state conn-id status
202.x.x.x 175.x.x.x QM_IDLE 1001 ACTIVE(code)
View 9 Replies
View Related
Jun 13, 2012
The scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
View 1 Replies
View Related
Nov 20, 2011
I want to establish VPN with GRE over IPsec. As ASA can't end GRE tunnels, I should pass it through inside to another 1841 router in datacentar network. Since datacentar is connected to internet via two wan links (separate ISPs) is it possible to establish two gre simultanous sessions between 1841 at branch office and 1841 at datacentar, one session per wan link at datacentar? That way, I need 8 gre separate sessions (tunnels) at datacentar 1841 router. Is it supported?Is GRE passthrough works like regular port forwarding or it is something that ASA handles with some special commands?
View 1 Replies
View Related
Aug 22, 2011
I´m getting a dynamic public IP from my provider and what I´m trying to do is to establish a remote vpn tunnnel using IPSec which I achieve but every time the sessions resets or the ASA 5505 resets I get a new public IP and I need to put the new IP on the remote client so I can establish the vpn... How can I establish an ipsec vpn using DNS? For this scenario the remote vpn client is a vpn phone but it could be for any vpn client.
Private IP Public IP Private IP
PBX ---- (LAN) ---- ASA 5505 ---( Internet ) --- Remote Site ( Router ) --- (LAN) -- VPN Phone
View 3 Replies
View Related
Apr 18, 2012
How do I find out external IP I need to connect to my office!
View 2 Replies
View Related
Jul 12, 2012
I am trying to set up a site to site ipsec connection. AT site A, I have Vlan's 652-10.55.216.0/24, Vlan653 -10.55.217.0/24, Vlan 654-10.55.217.0/24 and Vlan655-10.55.219.0/24 and at site B, Vlan650-10.55.214.0/24 and Vlan651-10.55.215.0/24.The problem is that I am unable to get any associations when i do a "sh crypto isakmp sa"/"sh crypto ipsec sa" on either router at each site.I am also unable to ping by pluging in a laptop into the site at each site. Laptop at site A is set to access vlan 655 and laptop at site B is set to acess vlan 651. I can ping all the devices from one end to the other.I have turned on debug crypto isakmp, debug crypto ipsec, debug crypto ipsec errors but dont get anything at all as output.I have attached the sh run for each router Cisco (1941/K9) and switch (Catalyst 3750) at each site.
View 4 Replies
View Related
Nov 21, 2012
I have an ASA 5525 and need to configure site to site ipsec vpn to 3 peers. I currently have an existing /28 public address from my ISP that is used by other services.Is there a way to use this existing ip range to configure IPSEC tunnels to 3 peers ?
View 10 Replies
View Related
Sep 12, 2011
I configurated Ipsec vpn at asa 5510. my inside ip 192.168.10.156my public ip: 85.x.x.xmy peer ip : 62.x.x.x
the project is that:
the remote site want the interesting traffic like that:
source ip 172.16.1.104 can access destination ip 10.0.154.27
My inside ip is 192.168.10.0/0 and i can not to change it 172.16.1.0/24 and i can not to add this ip at my network.
View 3 Replies
View Related
Apr 3, 2013
I have two Cisco routers - 2911 in HQ and RV180 in branch office. Because in HQ LAN network I have some development servers, to which guys from branch office need to have acces, I decided to setup VPN site-to-site between HQ and branch office. Everything went quite smoothly, on both devices I see, that ipsec connection is established. Unfortunately I am not able to ping resources from one network to other one and vice versa. Below is the configuration of 2911 router (I skipped som unimportant (imho) configuration directives) :
crypto isakmp policy 1
encr 3des
hash md5
[Code].....
View 9 Replies
View Related
Jan 28, 2013
With à customer we have à site to site VPN connection. In this tunnel there is one subnet routed with a 3des-sha encryption / hash. Now the want to add a new subnet in this tunnel, but with a AES-128 / MD5 encryption / hash. Is it correct if we make a new crypto map with a higher seq. number?
View 5 Replies
View Related
Aug 8, 2011
im drawing a blank trying to setup a site to site connection with a 5505 ASA using ipsec and isakmp.i have the pre shared key as well as the external address of the other end of the tunnel but do not remember what the commands are to setup the crypto map and isakmp.
View 7 Replies
View Related
Jul 10, 2012
We have a scenario where the Cisco ASA 5505 will be one end of a site-to-site VPN. The same ASA 5505 also allows Client VPN connection. The question is around IP pooling. If I assign a pool of IP's (192.168.1.20 - 192.168.1.30) for Client VPN connections - do I need to be sure that those same IP's are not used on the other side of site-to-site VPN ?
There could be PC's/Servers running 192.168.1.0/24 on the other side of site-to-site VPN. Would this cause an address conflict ?
View 4 Replies
View Related
Apr 24, 2013
I have configured Ipsec vpn tunnel beetween two routers (from site A to site B) over untrusted internet connection by cisco 3825 routers and i can successfully access both of this routers. But now i need to access internet on site B router sitting on site A router. So that if i run traceroute from A site machine then the gateway by which internet passing through shows the ip of site B.
The Architecture of our both site routers :
Site A 10.1.11.0-----Router A 172.18.12.1-----VPN tunnel----Router B 172.18.12.2-----Site B 10.4.11.0
/////Create IKE policy
crypto isakmp policy 1
encr aes
authentication pre-share
group 2
[Code] .....
View 10 Replies
View Related
Dec 1, 2011
How can I NAT the same set of four hosts and give them access to two different networks across an IPSEC site-to-site VPN tunnel? I'm using an ASA5520 running 8.04.
I have four hosts say: 10.240.1.1-10.240.1.4
They need access to two different networks:
205.100.150.0
140.175.200.0
I woud like to NAT them as something like:
7.5.210.1
7.5.210.2
7.5.210.3
7.5.210.4
View 1 Replies
View Related
Nov 20, 2012
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: [code]
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505. [code]
All these remote networks are at the Main Site Clavister Firewall.
View 1 Replies
View Related
Nov 28, 2012
I have a situation where the site-to-site tunnel is already established using PPTP IPSec VPN with non Cisco Gateways terminating the link on each end. These non Cisco Gateways do not support L2TP tunneling, and there is no plan to change them.Beyond the Gateways on both ends, we have a Cisco 4500 series switch. We need to forward the 802.1q tagged VLANs between the two sites. Is it possible to use 802.1Q tunneling in this case, going via a PPTP tunnel ?
Cisco's setup uses dot1q-tunnel over a L2protocol-tunnel to preserve the original client VLAN tagging, so does this mean that the only option we have is to setup a L2TP tunnel at the Cisco device endpoints, and have that tunnel go through the existing PPTP tunnel (established between the 2 non Cisco VPN Gateways) ?
View 1 Replies
View Related
Apr 30, 2013
My requirment is Clients from site A should access the Internet from site B (B will be providing internet to site A), So I have configured Ipsec vpn tunnel beetween two routers (from site A to site B) over untrusted internet connection by cisco 3825 routers and i can successfully access both of this routers.I have configured a client machine in site A and configured gateway of this client is 10.1.11.254 but dont have internet there.
View 2 Replies
View Related
Mar 15, 2011
I have a Cisco 2911 router and a Cisco RV 120W router and i would like to establish a VPN tunnel between theese two. I have defined the settings on the Cisco RV 120W router and i just want the Cisco 2911 to follow those. setting up a connection with Cisco IOS.
View 1 Replies
View Related
Oct 3, 2012
Site A has an ASA 5510 and a single internet connection.Site B has two internet connections (primary and backup). If Site B also has an ASA, I can configure Site A's ASA to deal with a failover at Site B (set peer 1.1.1.1 2.2.2.2). Does this work if Site B has an IOS router instead of an ASA? In other words will "set peer 1.1.1.1 2.2.2.2" on the ASA work when it's talking to IOS on the other end?
View 15 Replies
View Related
Dec 4, 2012
Question on ASA VPN tunnels. I have one ASA 5510 in our corporate office, I have two subnets in our corporate office that are configured in the ASA in a Object group. I have a site to site IPSEC tunnel already up and that has been working. I am trying to set up another site to site IPSEC tunnel to a different location that will need to be setup to access the same two subnets. I'm not sure if this can be setup or not, I think I had a problem with setting up two tunnels that were trying to connect to the same subnet but that was between the same two ASA's. Anyways the new tunnel to a new site is not coming up and I want to make sure it is not the subnet issue. The current working tunnel is between two ASA 5510's, the new tunnel we are trying to build is between the ASA and a Sonicwall firewall.
View 3 Replies
View Related
Nov 1, 2011
I am having issues getting my ASA 5540 at site A, to pass TFTP and SYSLOG from itself across the IPSEC tunnel to our SYSMON servers (Syslog and TFTP) that live at site B. I have followed the suggestions of other threads and I am still not getting anywhere. Here is a quick topology diagram.
View 6 Replies
View Related
Sep 20, 2011
Can i know cisco 2800 router can support how many site-to-site ipsec tunnel without vpn module?
View 2 Replies
View Related
