Cisco VPN :: ASA5505 With Dual ISP And IPSEC?
Sep 18, 2011
I have problem with dual ISP + IPSEC on my cisco ASA5505 sec plus licence.Routing is working correct (connect to Internet from siteA is working trought 1st also second ISP) but IPSEC is working just trought the first ISP! It seemt that phase 1 and 2 of IPSEC is correct but packets are just encrypting but not decrypting.
I'm trying ping from siteA (PC - 10.4.1.66) to siteB (PC - 10.3.128.50)
config site A:
##########################################################################
ASA5505 Version 8.2(1)
interface Vlan1
nameif inside
security-level 100
ip address 10.4.1.65 255.255.255.248
!
interface Vlan2
[code]....
View 7 Replies
ADVERTISEMENT
Nov 17, 2011
I have an ASA 5505 with the Security License running 8.4 and 6.4.5 software, I have a fully working VPN solution on there using a ISP IP - works fine. My boss wants to split the lines/bandwidth to another ISP we have coming into the office. So what I want to acheieve if possible is this Say my current isp is 5.5.5.5, my internal network is 192.168.2.x and my other ISP is 6.6.6.6 - is it possible to use the ASA to accept VPN clients from both ISP's and use the internal network?
View 2 Replies
View Related
Oct 1, 2010
for the purpose of a redundency, incase the primary ISP goes down the backup kicks in.Can this be done with the basic license (max 3 vlans) or you need to have the security plus license. (20 vlans) Currently not using the 3rd vlan (dmz)
View 5 Replies
View Related
Jun 17, 2012
Can I have two IPSec tunnels over two different Internet links to two different destination?
View 1 Replies
View Related
Jun 18, 2008
I have two ISP's and I want to channel specific traffic out of an interface based on traffic type. Will the ASA 5505 security bundle allow me to route specific traffic out through a specific interface?
View 2 Replies
View Related
Jul 1, 2012
I've been searching the net for days now trying to configure the ASA5505 for dual DHCP ISP use. All guides available assume you have one static.
After realizing that it required a Security Plus license to even configure 3 VLANs.
I can choose a backup interface in ASDM. It even says dual ISP enabled. Why cant there be a guide or simple configuration example or am I the only one looking for this kind of solution?
Customer has two ADSL internet connections and want to switch between them if they fail. No load balancing required.
View 2 Replies
View Related
Oct 30, 2012
I have setup an ASA5505 running 8.2 with dual ISP's
Primary link is the current live static route out and the backup picks up if the primary fails. That all works great However I have an issue with inbound NAT rules
I have configured an inbound static on the primary which works great
static (inside,primary) *.*.*.* 10.1.1.1 netmask 255.255.255.255 access-list outside_access_in line 2 extended permit tcp any host *.*.*.* eq 3389 (hitcnt=4)
Question? With the primary link active and the default route pointing out through the primary, am I able to configure an inbound NAT to the same inside host 10.1.1.1
on the backup link?
If the primary fails users will need to be able to connect inbound to this service
When I try to set it up I got this error ERROR: Static PAT using the interface requires the use of the 'interface' keyword instead of the interface IP address
So I tried that and got this error WARNING: All traffic destined to the IP address of the backup interface is being redirected. WARNING: Users will not be able to access any service enabled on the backup interface.
So what is the best practice for configuring inbound NAT for a dual ISP configured ASA
View 1 Replies
View Related
Jun 3, 2012
I have a site with an ASA5505 and 2 isp connections but the catch is the 2 isp's are giving me a dynamic IP so I am unable to use this [URL]
View 3 Replies
View Related
Jul 25, 2011
I have set up a IPsec L2L VPN between a ASA5510 and a ASA5505 which is working just fine.Every now and then our management station receives the following syslog message: Session disconnected. Session Type: IPsec, Duration: 2h:23m:23s, Bytes xmt: 3283338, Bytes rcv: 8637607, Reason: Phase 2 Error.I have already searched the forum for this message to exclude all the possible reasons for this message:
- the complete crypto maps are the same on both ends (lifetime, psk, pfs etc)
- the ACL's used in the crypto maps are exactly the opposite of each other
View 2 Replies
View Related
Jun 10, 2013
I currently have my 5505 setup for AnyConnect SSL VPN connections. Is it possible to also configure the 5505 for IPSec VPN connections? So, essentially my ASA will be capable of running SSL and IPSec VPN tunnels, concurrently.
View 2 Replies
View Related
Aug 9, 2012
I'm having trouble configuring an ASA5505 on version 8.31 code for an IPSec tunnel. I've done this multiple times on 8.2.5 but can't seem to get my tunnel to even attempt to come up on this ASA. Not sure if it's relevent or not, but this remote ASA has never been used for another VPN tunnel before. When I attempt to ping a host on the other side of my tunnel, I just see the following: 8108# sho crypto isa sa
There are no isakmp sas
My local network is 10.1.1.X/24 and my remote peer network contains 66.37.227.X/24. I've been working on this for the better part of the day and would love to get it resolved.
View 8 Replies
View Related
Feb 26, 2013
I'm a CIsco ISR, Setting up my first ASA, which seems to be going well.I've setup an IPSEC VPN to a non Cisco device. And have connectivity between devices in each subnet.
-Subnet A - non Cisco - 10.10.13.0/24
-Subnet B - ASA 5505 - 192.168.2.0/24 (ASA is .254)
From Subnet A I can ping every device except the ASA on .254.
Edited Config attached, IP's changed for privacy, passwords removed.Let me know if I've removed too much of the config.
View 3 Replies
View Related
Mar 2, 2012
I am having all sorts of trouble connecting a Cisco RVS4000 to a Cisco ASA5505 over IPSec... I have used the "site to site" vpn wizard, I have a fress "factory reset" on my asa 5505...
View 11 Replies
View Related
Feb 20, 2008
Just bought myself an ASA5505 to replace a PIX 501, and having transferred over most of the previous config I've managed to get the two IPSEC VPN tunnels working as before.
Unfortunately when I try and SSH to the ASA the connection just resets instantly even when the tunnel is up. It seems as if the ASA is actively refusing the connection, though the log doesn't state this. I had always presumed that traffic over an established IPSEC tunnel was implicitly trusted and not subject to usual access-list rules.
I am unable to SSH to the ASA from the 10.0.0.x range, but I can SSH to a machine on 10.27.0.4 (so I know the tunnel is up and working)
Config (minus irrelevant sensitive information) is attached for reference.
Also - though I'm not sure how relevant it is given the tunnels appear to work - when I enter the line "crypto map meepnet-map interface outside" in config mode the ASA reports "WARNING: The crypto map entry is incomplete!" even though I have supplied the access-list, peer and transform-set variables.
View 12 Replies
View Related
Jun 18, 2012
I'm having problems configuring an IPSEC VPN between an SRP521 with a dynamic IP and a ASA5505 with a static IP. Static to Static is fine between these devices and I can configure that without problems. Dynamic to Static however.
View 1 Replies
View Related
Jun 7, 2011
I'm trying to set up a S2S VPN between two ASA5505 SP units running ASA Version 8.2(1). I've ordered additional ADSL2 lines to handle this traffic and I'm having troubles with the configuration for the additional PPPoE connection. Here is are extracts from my current config; First the interface vlans
!
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
[code]....
The result being that I can ping the OUTSIDE interface, but get no reply from the VPN interface. I've checked ADSL lines, they are up. The two PPPoE sessions are logged in and active. I can even see the ICMP packets hit the VPN interface, but there is no reply.
View 1 Replies
View Related
Sep 5, 2011
I have two sites with identical asa 5505's and each has the dual wan/ISP links and are set for failover using sla monitor tracking. I would like to create a vpn between these two sites that stays active regardless of which ISP link is online. Do I simply make two crytpo map statements10 and a 20 inside each of the asa's to each of the other ASA's STATIC PUBLIC IP's? [code]
View 6 Replies
View Related
Oct 8, 2012
Got a situation where Location_A got TWO ISP and Location_B got One ISP.Using ISP 1 link Location_A establishes IPSEC Tunnel with Location_B .How do I establish redundancy from Location_A point of view, if ISP1 is down then ISP2 should establish IPSEC tunnel with Location_B.At Location_A both ISP links terminates on the cisco PIX-525 and all (VPN) crypto configuration is on PIX 525 running version PIX Version 7.2(4)7At Location_B VPN is terminated on a PIX Version 6.3(3).
View 2 Replies
View Related
Jan 20, 2013
I'm trying to make a very plain and simple network with the ASA 5505, I've strated from scratch over a dozen times triyng to find where I'm going wrong. My main goal is to simply create an IPSec VPN connection to my ASA 5505 and simply ping and connect to devices with the "inside network", so far I can easily create and establish a IPSec VPN Connection, but up to this point, I cannot successfully ping or access a single device on the ASA 5505 inside network.I've taken, create the IPSec profile with the ASDM wizard, add exemption for the VPN IP Pool, add access-list from this Cisco link, url...All this and I can't make a single connection to the inside network. [code]
View 7 Replies
View Related
Sep 28, 2011
We have two sites connect with an IPSec L2L VPN.
-Site A: 192.168.13.0/24
-Site B: 192.168.2.0/24
On both sites we have a ASA5505(Base license) to terminate the tunnel.On Site B we also got a remote access vpn to which we can connect using the vpn client.The lan2lan tunnel works fine and so the remote access vpn.Now i want to connect to Site A using my vpn client connected to Site B. [code] There are no vpn-filters or other special policys in place..If tried to ping from my vpn client to Site A while i was debugging ipsec 255 on site B: the asa matched the l2l-tunnel for traffic sourced from 192.168.25.x to 192.168.13.x but when im doing a show crypto ipsec sa detail there are no packets getting encrypted..so of course no packets reaching my asa on site a.
View 9 Replies
View Related
Jan 9, 2013
Recently, I set a ASA5505 with Ipsec VPN. And I try AAA authenticate with internal Windows 2008 server. As docuemnt I read, I configure from ASDM authentication with "NT Domain". And then point to internal DC, which is Windows 2008 server. While I test it, it shows error
"Authentication test to host 192.168.xxx.xxx failed. Following error occurred -- ERROR: Authentication server not responding. No Error"
View 3 Replies
View Related
Jun 20, 2011
I have a XP workstation behind my ASA that can not connect to a client's network via Cisco VPN Client using IPSec...
In the logs it shows the translation is working on 500 but the VPN Client has the error 412, that the client is not responding.
Config below
ASA Version 8.2(1)!hostname RWFW1enable password encryptedpasswd encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address x.x.x.x
[Code].....
View 16 Replies
View Related
Jul 10, 2012
We have a scenario where the Cisco ASA 5505 will be one end of a site-to-site VPN. The same ASA 5505 also allows Client VPN connection. The question is around IP pooling. If I assign a pool of IP's (192.168.1.20 - 192.168.1.30) for Client VPN connections - do I need to be sure that those same IP's are not used on the other side of site-to-site VPN ?
There could be PC's/Servers running 192.168.1.0/24 on the other side of site-to-site VPN. Would this cause an address conflict ?
View 4 Replies
View Related
May 22, 2012
I've spent 2 days already trying to get 2 ASA 5505's to connect using an IPSec vpn tunnel. I cannot seem to figure out what im doing wrong, im using 192.168.97.0 and 192.168.100.0 as my internal networks that i'm trying to connect over a directly connected link on the outside interfaces with 50.1.1.1 and 50.1.1.2 as the addresses (all /24). I also tried with and currently without NAT enabled. Here are the configs for both ASA's, the vpn config was done by the ASDM, however i have also tried the command line apporach with no success. I have followed various guides to the letter online, starting from an empty config and from factory default. I have also tried the 8.4 IOS. [code]
View 2 Replies
View Related
Feb 19, 2012
I would like to make a design with 4 Nexus 5596UP. 2 of them equipped with Layer 3 Expansion Module so they can serve as core layer and the other 2 Nexus used as Layer 2 for aggregation server layer.The 2 Nexus in the core layer will run HSRP and will peer with ISP via BGP for Internet connection The 2 Nexus in the aggregation layer will be configured as layer 2 device and have FEX and switches connected to them.What I am ensure of is how the vpc and port-channel configuration should look like between the 4 nexus. What I was thinking is to run vpc between the 2 Nexus in the aggregation layer and between the 2 Nexus in the core layer. Than I was thinking of connecting each Nexus in the aggragtion layer to both Nexus in the core layer using port-channel and vice-versa.
View 3 Replies
View Related
Dec 17, 2012
how to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
View 2 Replies
View Related
Mar 29, 2012
I wanted to ask a question about the diagram I have included. We are bringing up 2 MPLS WAN connections and would like some specifics on the best design. We are using BGP to the providers. From there we have big questions. We can run BGP internal and are licensed to do so on the N5K's. The N5Ks are currently using HSRP for inside LAN clients as default gateway. We want to load balance and provide redundant routes using a dynamic approach. Should we use BGP internal utilizing the connections between the routers? Should we use HSRP on the routers? How best to get the routes to the N5K and should we be considering this?
View 5 Replies
View Related
Feb 21, 2013
I run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
I got problem though when i tried more complex connection diagram. [URL]
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.
View 2 Replies
View Related
Apr 29, 2013
I tried any type of combination and just couldn't make it works. Only PPTP works well. Whether Apple iOS IPSec VPN is supported or not?
View 11 Replies
View Related
Jul 20, 2012
i have the asa5505 with asa8.4.5 and asdm 6.4.2. my asa work like site to site vpn with the other asa5505. i would be love that monitoring status of VPN. i enabled on asa logging, i puted address of smtp server, receipent email, source email, the problem is because my smtp server require authentication, TLS. how set configuration on asa5505?
configuration of logging for send notification on email.
View 3 Replies
View Related
Jan 22, 2011
We are pulled the plug on our PIX 501 as its not letting us use all 100Mbit that our cable provider is now piping to us. I read the conversion guide but it made no mention of the 501's. Only the 515's or newer.The ASA5505 is putting up a little bit of a fight (This what I get for failing my CCNA??)After refusing to configure the LAN ip address to something other than what it was shipped with, I broke down and connected to the management console and forced an IP address on the LAN side. Now I reset my default config and everyone can get on the internet.Until the ISP cuts you off because you forgot to set your static IP. Oh, and by the way, they dont support Cisco gear.
When I attempt to assign the IP to the outside interface, it accepts without a hitch, but everything grinds to a halt. I cannot have this, as I have off-site users that operate with dedicated ports using Remote Desktop. I've attempted to set the IP via both ASDM and management console. I've tried setting a static route, but that doesnt give me any love either. Im running ASA Version 8.2(1) and ASDM Version 6.2(1)Once I get the static IP set and working properly, I can tackle moving the port configs.
View 10 Replies
View Related
Aug 22, 2012
Our client has a vendor who needs to establish a VPN tunnel to their own router which sits behind our Firewall.
VPN Concentrator (Vendor) <------> ASA5505 Client (7.2) <-------> 3750 Switch <-------> VPN ASA outside Interface - 208.64.1x.x4 DG - 208.64.1x.x3
ASA Inside Interface - 172.20.58.13/30
3750 Switch Interface Connected to ASA - 172.20.58.14/30 and DG - 172.20.58.13
3750 Switch Interface connected to VPN router - 172.20.58.21
VPN Router Interface connected to the 3750 - 172.20.58.22/30 DG - 172.20.58.21
I have also attached a Visio for this and the running configuration from the ASA and 3750. We don't have access to the TNS VPN router. Our responsibility is to just to make sure the tunnel comes up.
1) Create a static NAT on the ASA for Public to Private IP of the VPN router
Public - 208.64.1x.x5 / 28
Private - 172.20.58.21 / 30
Will the ASA automatically ARP for this address or do i have to configure another interface on the ASA with this public IP?
2) What would the access list look like on the ASA?
3) The client gave us some config to copy the stuff on the ASA so that they can create the tunnel but i couldn't put those commands in the ASA. How would this be applied and on what interface?
Firewall Access: The following information pertains to access between the VPN router and the
VPN concentrator. If a firewall/router is present in front of the VPN the following services need to be
allowed:
permit esp host 208.224.x.x any
permit gre host 208.224.x.x any
permit udp host 208.224.x.x any eq isakmp
permit udp host 208.224.x.x any eq non500-isakmp(code )
View 2 Replies
View Related
Jan 19, 2012
am not sure if it is different on the 8.2 or if I am missing something. I can connect to the vpn but cannot get to the inside computers. I can ping them from the ASA but not from the vpn client.
View 17 Replies
View Related
