Cisco VPN :: DPC3925 Vpn With Netscreen Firewall?
Sep 13, 2012
I am trying to get up an point to point VPN between a Cisco DPC3925 and a netscreen 5GT Firewall I have configured up everything as i think it should, i belive the phase one and phase two are both configured ok, if i change the phase one settings to something different then i will get a different error on the cisco I am using Auto Ike, with a shared key and PFS - both phase one and phase two are set the same at both ends cisco / netscreen?When I try to connect, the VPN log on the CISCO shows the below, but on the netscreen it thinks that phase one Negotiations are complete (in logs etc) The netscreen seems to be much more configurable than the CISCO, so i guess i need to change something on that, what the cisco is expecting to receive ftom the netscreen that its not getting from the logs, I have chaged the external IP's in this log?
1.1.1.1 is the Cisco,, 2.2.2.2 is the netscreen
Thu Sep 13 14:49:53 2012 IKE Phase 1 Negotiation FAILED 1.1.1.1==>2.2.2.2
Thu Sep 13 14:49:47 2012 phase2 negotiation failed due to time up waiting for phase1. 02.2.2.2 ==>1.1.1.1
Thu Sep 13 14:49:43 2012 error -1 process rcvd packet
[code].....
View 3 Replies
ADVERTISEMENT
Mar 5, 2013
I am currently migrating a netscreen firewall to a asa 5515 version 8.6 The issue is setting up the management connectivity.
basically the management IP of the cisco asa is not advertised. But, we want to route a management IP through the management interface to interface Gi0/2.
so IP of management interface is say - 216.10.100.10. and the IP of the inside interface is say - 198.1.1.10/24 on our router we have a static route sending 198.1.1.0/24 to next hop of 216.10.100.10 (management interface of cisco asa).
On the Cisco ASA can I send the traffic to the inside interface and manage the firewall via ssh that way?
View 4 Replies
View Related
Dec 27, 2011
Monitor a VPN tunnel that has as end devices a Cisco ASA 5520 and a NetScreen Firewall. I'll like to be receive an alert when the VPN is down.
View 1 Replies
View Related
May 13, 2012
I recently got an MBP, while I tried connecting it to the wi-fi connection, I keep getting the "invalid password" prompter. I tried connecting my other mac computer and Iphone to the connection and it works. I also tried connecting via ethernet as well, it worked as well. I have been trying to call the CISCO number to no avail, and it is really frustrating to be paying premium for the connection, I don't feel supported at all.
View 2 Replies
View Related
Dec 28, 2012
I have dpc3925 router and I want to restrict the time of internet access to a certain laptop.
View 7 Replies
View Related
Apr 16, 2012
have received an Cisco Model DPC3925 modem/router from UPC (provider in the Netherlands) and they allow me to have 120Mbit connection, but with my own WIFI Adapter I only received between the 40Mbit/60Mbit speed. My question is the following; Wich WIFI adapter is the best adapter for my Cisco Model DPC3925 modem/router?The distance between the modem/router and my pc is not that much. And when I use an cable the connection is between the 90Mbit/110Mbit. The WIFI adapter that I now use is the: TP-Link TL-WN881ND. I was thinking to buy a Linksys AE1200, but I dont know if that adapter is much better then I already have.
View 6 Replies
View Related
Apr 29, 2012
Successfully setup X Box connected via DPC3925 WIFI router to to Win 7 Media Center? I am sure I had uPNP enabled and I tried turning off Firewall for home network but no luck!
Adding the extender from Media Center always claims it can't find the X Box (Yes, I did enter the 8 digit key exactly as displayed on TV).
View 1 Replies
View Related
Aug 7, 2011
I have a established VPN between NS500 and AS5505
The following diagram shows whats going on.
customer source subnet: 192.168.2.0/24
Source NAT to 10.160.64.33
NS500: sub int 1.3 : 10.160.64.1
Destination NAT to : 199.53.28.17 <-- this is a server IP which allows telnet on specific ports. The source has to be 10.160.64.33 to pass the firewall.
In the same way a new connection is required to another server IP behind a firewall.
target is going to be : 159.5.250.194/32
The source for this connection has to be 159.5.188.40 in order to pass the firewall and hit the above target.
View 1 Replies
View Related
Jan 1, 2012
I am working on cisco ACS 5.0, authentication is working fine on netscreen. Can acs be used for authorization and accounting of netscreen devices. if yes, what will be the configurations.
View 1 Replies
View Related
Jul 21, 2012
I am new on CISCO but learning. I need to allowing ping from inside interface to outside interface. I need to allow SSH from outside to PIX506E and one node on inside 192.168.66.x. I also need to setup 32 public IP adresses to route inside nodes. I also need converting the rules from Netscreen firewall to PIX506E. Last, getting PDM working when i connect it start two windows but does not get PDM so i can configurate it thru PDM. [code]
View 2 Replies
View Related
Oct 21, 2011
I wants to inegrate Juniper netscreen firewall in Tacacs Cisco Acs 5.1.As I go through Juniper KB which mentioned that I need to enable Netscreen Service in Cisco ACS 5.1. how to enable Netscreen service in Cisco Acs 5.1 and how I got Further to integrate Juniper Netscreen Device in Cisco cs 5.1
View 2 Replies
View Related
Jun 3, 2011
Several of my older netscreen devices only support radius authentication and I'm having trouble migrating them from ACS 4.2 to ACS 5.1. When I try to authenticate, the authentication passes in ACS but it doesn't log you into the Netscreen (you see a auth failure in the Netscreen logs). I believe that the custom attributes are not being passed from ACS to the Netscreen. The custom attribute we are trying to pass is "NS-Admin-Privilege" with type integer and a value of 2. The netscreen is setup so that the user privledges are obtained from the ACS server.
Any setup where they are using Cisco radius authentication to authenticate Netscreen devices?
View 2 Replies
View Related
Aug 9, 2011
I am trying add custom attributes for Juniper Netscreen TACACS+ authentication to a v5.2 ACS. The advice is to add it to the group as follows:
ervice = netscreen {
vsys = root
privilege = read-write
} I know how to add this to a version v4.x ACS
However, I do not know how to apply this to the custom attribiutes to a v5.x ACS?do I add the vsys and privilege attribute seperately or together? What should be the attribute name? netscreen? Should it be mandatory?
View 4 Replies
View Related
Aug 15, 2005
I am having some difficulty setting us this vpn connection between our cisco 837 box and netscreen 25.The Phase 1 proposals match and are accepted, then the cisco log seem to go round and round in circles trying the Exchange a Key??? [code]
View 5 Replies
View Related
Apr 22, 2013
I will be implementing a new firewall (cisco asa 5515x) on my existing 3750x (server switches) and my 2960s (user switches). What should I need to apply on my firewall and swtiches to make the implementation successfull. I will put my 3750x as my DMZ and my 2960s as my inside. The 3750x have multiple subnet and also the 2960s.which features and technologies i need to know on those 3 products. my 3750x and 2960s don't have any ACL defined and most common features are vlan, switchport, trunking, spanning-tree, stacking, vtp.how my asa knows that my 3750x/2960s have multiple vlans. my current connection right now on 3750x and 2960s is just through 6 ports i assigned as one trunk, below is my config [code]
my 2960s vlans are almost the same with my 3750x except vlan 160, 170, 192. but of course when i put this in asa, i have to segragate vlan for 3750x (192, 100, 110,160, 170) and 2960s (130, 150). for my 2960s connection to the asa and since this will have big bandwidth, i will use 3 ports on my asa (and trunk it) connecting to my 2960s and i will use 2 ports on my asa (and trunk it) connecting to my 3750x. the one internet ports and my one management ports on my asa will stay like that.
View 2 Replies
View Related
Jun 11, 2012
I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
View 7 Replies
View Related
Aug 2, 2011
We had a problem with SMTP inspection dropping some regular emails (Cisco 2901 IOS 15.0). The original configuration.
View 2 Replies
View Related
Jun 21, 2011
We had a problem with SMTP inspection dropping some regular emails (Cisco 2901 IOS 15.0).Incoming mails are going thru Spam and Virus Blocker so that bypassing SMTP inspection is not security issue in this case.
View 1 Replies
View Related
Dec 28, 2011
I have a question with regard to setting up the ID firewall on the ASA 5585 in a single forest, multiple domain windows network.Currently I have a semi-operational IDF at the top level but can't find users on the lower other domains, here is the setup:I have 3 domains.
[URL]
Both domains have a two way parent-child trust and I can look for users in AD Users/Computer on both domains. I initially setup the ASA to look at domain1.test.com using an LDAP aaa-server per the IDF instructions, and then proceeded to configure the ad-agent. I installed the adagent on the domain1.test.com domain controller configured the settings on that system and had no problem adding users to the firewall and getting functionality within domain1. I looked to see if I could see domain 2 and domain 3 users and found none. I went ahead and added the domain2 system to the adagent on the DC and the system says that it is up, but when I search for users is not pulling them from domain2. Instead, it shows domain1 users as domain2user1. I also configured another adserver in the ASA to search ldap on domain 2 to no avail.The cisco documentation states the following:•Before you configure even a single domain controller machine using the adacfg dc create command, ensure that the AD Agent machine is first joined to a domain (for example, domain J) that has a trust relationship with each and every domain (for example, domain D[i]) that it will monitor for user authentications (through the domain controller machines that you will be configuring on the AD Agent machine). Single Forest, Multiple Domains—All the domains in a single forest already have an inherent two-way trust relationship with each other. Thus, the AD Agent must first be joined to one of the domains, J, in this forest, with this domain J not necessarily being identical to any of the domains D[i] corresponding to the domain controller machines. Because of the inherent trust relationship between domain J and each of the domains D[i], there is no need to explicitly configure any trust relationships.Reading that it sounds like it should just work. I had everything properly configured before I installed the adagent, but I'm guessing that there is a chance that you can't have the adagent on the top level DC and get to communicate with the lower level domains.
View 1 Replies
View Related
Apr 26, 2011
I do have the below setup,,
1. I have 6509 switch
2. I have 2 WLC configured in Active/Active mode connected in Trunk mode (L2 Port-Channel) connected with 6509 switch
3. On switch side i have configured the port as Trunk
4. L3 SVI for wireless users are created in 6509 switch (attached the diagram).
I would like to introduce a Cisco ASA 5520 firewall with AIp-SSM module so that all wirelees traffic can be inspected.
The issue is: Without changing any configuration in the network (switch & WLC) is it possible to introduce the firewall?
View 2 Replies
View Related
Sep 7, 2011
How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
View 1 Replies
View Related
Jul 27, 2011
I've been trying to configured Websense urlfiltering using ZFW feature on my Cisco 881G router. The router is running on IOS 15.0(1)M with Advanced IP Services. And I have confirmed it supports urlfilter feature.
This is what I tried to accomplish but IOS version 15.0x seems to have different command set.
-----------------------
class-map type inspect httptraffic
match protocol http
parameter-map type urlfilter param
server vendor websense 10.20.30.40
[Code]...
View 2 Replies
View Related
May 23, 2013
I was asked to enable netflow in an ASA Firewall for Orion/Solarwinds server monitoration. Firewall is a 5550, with 4G RAM, and no extra modules but SSM-4GE. This firewall has 5 DMZ segments and ans specific segment for internet traffic.There are segments as unique subinterfaces in physical interfaces. Other segments as individual subinterfaces in the same physical interface (but individual VLANs)Usually firewall CPU flows between 30% to 40%. Rarely to 50%.
1 - How dangerous or risky could be implement netflow in this firewall?...This firewall is very critical for the customer. My concern is regrading CPU, traffic generated, memory, etc
2 - In a month, firewall will be migrated from 8.2 software version to 8.4 software version. Is there any incompatibility in some commands?...Would be recommended to perform netflow configuration after software upgrade?
3 - How could it be implemented for Orion monitoring, regarding each individual sub-interface (and so, each VLAN assigned)?I there any recommendation regarding configuration, best practices?
View 6 Replies
View Related
Feb 26, 2013
I have some problem with the ASA 5510 ver 7.0(6). My manager wants to keep this as backup. tried lots of things but still users not able to access internet nor can i ping anywhere.For example when i ping 4.2.2.2 i dont get any reply.The runing config is below for ur ref :
HQ-ASA-01# show running-config
: Saved
:
[Code]......
View 9 Replies
View Related
Feb 5, 2012
I need to create a firewalled segment that not only separates hosts from general population, but also from each other. The solitary confinement of firewalled segments.I know that I could create a bunch of sub-interfaces, one for each host or group that needs to be isolated, but I'd really rather not have to do that if possible. 1) It could become a management nightmare between ACLs and sub-interfaces and 2) it's a waste of IP addresses.s there any way that I can create a bunch of separate VLANs behind the firewall and have them all terminate at the firewall, using a single firewall IP address for the gateway?
VLAN 1 - hosts 1.1.1.5 and 1.1.1.6VLAN 2 - hosts 1.1.1.7
Firewall DMZ Interface - 1.1.1.1VLAN 3 - hosts 1.1.1.8 and 1.1.1.9
This way, the hosts are isolated and can't talk to each other unless they're on the same VLAN.I'm working with an ASA 5510 running 8.2.4(4).
View 1 Replies
View Related
Feb 28, 2010
Can any ASA 5500 in particular the ASA5510 firewall support jumbo frames (i.e. greater than the default standard 1500 Bytes frames)?. I plan to use the ASAs to setup a point-to-point IPSec tunnel and need an Application frame of 4Kbytes intact and not segment it.I have done little checking on the Cisco Website and see it mention of Jumbo frames on the 5580 on 10Gig interface but didn't see mention 5510. 5580s are way over-kill and expensive for what I need is to run a mission critical one IPSec point-to-point with maximum of no more than 100Kbps so 5510 is perfect for me but not sure if it can carry the jumbo frame?
On the routers and switches it's the MTU settings and they are configurable per interface and I am OK and the circuit is T1 which the Telcos said it's OK since it's physical layer so the only unkown is the firewall.
View 2 Replies
View Related
Nov 17, 2011
Is there any significance to the parameter "firewall-group" in the command
firewall vlan-group <firewall-group> <vlan-id>…<vlan-id>?
In other words is the series of commands
firewall switch 1 module 3 vlan-group 1,2
firewall vlan-group 1 100,101,102
firewall vlan-group 2 200,201,202
exactly equivalent to
firewall switch 1 module 3 vlan-group 3
firewall vlan-group 3 100,101,102,200,201,202
or
firewall switch 1 module 3 vlan-group 1,2,3
firewall vlan-group 1 100,200
firewall vlan-group 2 101,201
firewall vlan-group 3 102,202
All three of these options associate the same set of vlans to the FWSM but using different groupings. As far as I can tell, these groupings have no functional significance either on the switch side or the FWSM side. These are simply three different ways of specifying exactly the same thing? Am I correct?
View 2 Replies
View Related
Jun 22, 2011
I have a ASA 5510 firewall with CSC module and Security Plus license for CSC module.Will you tell me how to configure my firewall to send emails to particular mail ID when someone login into the firewall or any virus attacks from outside.
View 6 Replies
View Related
Feb 24, 2011
I have a normal setup of ASA5505 (without security license) connected behind an internet router. From the ASA5505 console I can ping the Internet. However, users behind the Firewall on the internal LAN, cannot ping the Internet even though NATing is configured. The users can ping the Inside interface of the Firewall so there is no internal reachability problem. In addition, I noticed that the NAT inside access list is not having any hit counts at all when users are trying to reach the internet.
When i replace the ASA5505 with a router with NAT overload configuration on it, the setup works normally and users are able to browse the internet.
The ASA5505 configuration is shown below.
hostname Firewall
interface Ethernet0/0
description Connected To Internet Router
switchport access vlan 10
[Code].....
View 2 Replies
View Related
Apr 24, 2012
We were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies
View Related
Apr 8, 2012
I am a novice with networks but do have a fair understanding of networks. I have a small business network, utilizing a RVS4000 router (Firmware V2.0.27)I am attempting to set up firewall rules to block certain web sites at certain times.I have successfully set up rules using source and destination ranges, to deny service 24 hours a day everyday.
However and here is the problem when I attempt to edit any of the rules (I want to change the time to certain hours of the day) it allows me to edit the rule but when I attempt to save I get an error message up saying there are invalid characters and it will not save the changes?create the whole thing with the changes I want it works fine, is this a known bug?
View 1 Replies
View Related
Feb 19, 2012
I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?
View 1 Replies
View Related
Sep 23, 2012
I have a strange issue which happened to me last weekend with two ASA 5515X on version 8.6(1)2. There was a planned power shutdown which only affected the primary firewall. Failover was configured and running successfully. The configuration was also saved after every change made. After power was shut and primary firewall went off the secondary took over like it should but unfortunately all configuration was gone. We immediately powered on the primary again but also this one lost the configuration.
While reconfiguring the firewall we ran into another problem. The devices won't pair although it was the correct configuration. After three times removing and adding the same failover configuration the devices accepted the failover and worked together again.
I went through the bug toolkit and white papers regarding ASA 5515x and this particular version but were not able to find anything.
View 2 Replies
View Related
