Cisco VPN :: Two ASA5505 VPN Over Intenet
Aug 6, 2012
I have 2 x ASA 5505's , I would like one to sit at my office behind an ADSL router with a static IP address, and be configured as a Server. I would like the other to connect to an ADSL router with a dynamic IP address, and be configured as a Client.
This must be a plug & play setup, so that when the 5505 client is plugged into ANY broadband router, it automatically creates a VPN tunnel to the 5505 server. Incase it's relevant... the purpose of this link will be to stream video data back to my office from remote locations. We have "played" around with the ASDM, EasyVPN and wizzards and still cannot get this to work!
View 3 Replies
ADVERTISEMENT
Jul 20, 2012
i have the asa5505 with asa8.4.5 and asdm 6.4.2. my asa work like site to site vpn with the other asa5505. i would be love that monitoring status of VPN. i enabled on asa logging, i puted address of smtp server, receipent email, source email, the problem is because my smtp server require authentication, TLS. how set configuration on asa5505?
configuration of logging for send notification on email.
View 3 Replies
View Related
Jan 22, 2011
We are pulled the plug on our PIX 501 as its not letting us use all 100Mbit that our cable provider is now piping to us. I read the conversion guide but it made no mention of the 501's. Only the 515's or newer.The ASA5505 is putting up a little bit of a fight (This what I get for failing my CCNA??)After refusing to configure the LAN ip address to something other than what it was shipped with, I broke down and connected to the management console and forced an IP address on the LAN side. Now I reset my default config and everyone can get on the internet.Until the ISP cuts you off because you forgot to set your static IP. Oh, and by the way, they dont support Cisco gear.
When I attempt to assign the IP to the outside interface, it accepts without a hitch, but everything grinds to a halt. I cannot have this, as I have off-site users that operate with dedicated ports using Remote Desktop. I've attempted to set the IP via both ASDM and management console. I've tried setting a static route, but that doesnt give me any love either. Im running ASA Version 8.2(1) and ASDM Version 6.2(1)Once I get the static IP set and working properly, I can tackle moving the port configs.
View 10 Replies
View Related
Jun 17, 2012
Can I have two IPSec tunnels over two different Internet links to two different destination?
View 1 Replies
View Related
Aug 22, 2012
Our client has a vendor who needs to establish a VPN tunnel to their own router which sits behind our Firewall.
VPN Concentrator (Vendor) <------> ASA5505 Client (7.2) <-------> 3750 Switch <-------> VPN ASA outside Interface - 208.64.1x.x4 DG - 208.64.1x.x3
ASA Inside Interface - 172.20.58.13/30
3750 Switch Interface Connected to ASA - 172.20.58.14/30 and DG - 172.20.58.13
3750 Switch Interface connected to VPN router - 172.20.58.21
VPN Router Interface connected to the 3750 - 172.20.58.22/30 DG - 172.20.58.21
I have also attached a Visio for this and the running configuration from the ASA and 3750. We don't have access to the TNS VPN router. Our responsibility is to just to make sure the tunnel comes up.
1) Create a static NAT on the ASA for Public to Private IP of the VPN router
Public - 208.64.1x.x5 / 28
Private - 172.20.58.21 / 30
Will the ASA automatically ARP for this address or do i have to configure another interface on the ASA with this public IP?
2) What would the access list look like on the ASA?
3) The client gave us some config to copy the stuff on the ASA so that they can create the tunnel but i couldn't put those commands in the ASA. How would this be applied and on what interface?
Firewall Access: The following information pertains to access between the VPN router and the
VPN concentrator. If a firewall/router is present in front of the VPN the following services need to be
allowed:
permit esp host 208.224.x.x any
permit gre host 208.224.x.x any
permit udp host 208.224.x.x any eq isakmp
permit udp host 208.224.x.x any eq non500-isakmp(code )
View 2 Replies
View Related
Jan 19, 2012
am not sure if it is different on the 8.2 or if I am missing something. I can connect to the vpn but cannot get to the inside computers. I can ping them from the ASA but not from the vpn client.
View 17 Replies
View Related
Jun 16, 2011
I have ASA 5505 with outside interface IP 206.206.206.5 I configured the SSL vpn on this but still i am getting page can not be displaed when opening https://206.206.206.5 from broadband.
Below is the related configuration in ASA. What needs to be done in order to able to connect SSL vpn.
group-policy GroupPolicy1 internalgroup-policy GroupPolicy1 attributesvpn-tunnel-protocol IPSec l2tp-ipsecwebvpn functions url-entry file-access file-entry file-browsing
tunnel-group DefaultWEBVPNGroup general-attributesdefault-group-policy GroupPolicy1tunnel-group DefaultWEBVPNGroup webvpn-attributesnbns-server 10.10.10.11 timeout 2 retry 2
policy-map type inspect http Http_inspect_policyparameters protocol-violation action drop-connectionclass BlockDomainClass resetpolicy-map global-policyclass global-class inspect dns inspect esmtp inspect ftp inspect netbios inspect rsh inspect rtsp inspect snmp inspect sqlnet inspect tftp inspect xdmcp inspect icmppolicy-map inside-policyclass HTTPTrafic inspect http Http_inspect_policy!service-policy global-policy global
webvpnenable outsideurl-list nuk001 "abc002" cifs://10.10.10.1 1
View 2 Replies
View Related
Jun 26, 2012
We have multiple servers on the DMZ (192.168.2.0/24) but they cannot access any resources in the Inside, by default. We would like to open up a Syslog server from the Inside (10.1.1.5) to the DMZ servers, so we can collect system log from the servers.
View 2 Replies
View Related
Nov 17, 2011
I have an ASA 5505 with the Security License running 8.4 and 6.4.5 software, I have a fully working VPN solution on there using a ISP IP - works fine. My boss wants to split the lines/bandwidth to another ISP we have coming into the office. So what I want to acheieve if possible is this Say my current isp is 5.5.5.5, my internal network is 192.168.2.x and my other ISP is 6.6.6.6 - is it possible to use the ASA to accept VPN clients from both ISP's and use the internal network?
View 2 Replies
View Related
Jan 17, 2012
I have 4 remote sites that are using a ASA as thir firewall / router. I'm setting up a full mesh VPN between all the sites. One of the sites have a UC500 and the other sites access that UC over the VPN tunnels. I would like to set up some basic QoS for the VOIP traffic
The site that has the UC will have multiple vpn tunnles coming in from the remote sites. How will I do QoS with voice traffic on that site?
View 11 Replies
View Related
Jul 8, 2012
I have 2 office buildings using Cisco 800 series routers with a L2L VPN between both. I'm upgrading the router to an ASA5505 at one of the offices but can't figure out the L2L VPN on the ASA. Specifically, can't figure out how to set the pre-shared key. On the Cisco 800 it's:That doesn't seem to work on the ASA. Here is my current config on the Cisco 800. [code]
View 9 Replies
View Related
Jun 17, 2011
I need to create second VPN in same ASA5505, it has already a VPN to one of our clients. So it alredy have a transformset,cryptomap,policy.Now i need to create new one. i like to create a seperate transformset and crypto map for this 2nd VPN with a new name to identfy very easily.But i have doubt like may it will affect the current VPN? because it has another VPN with another tranformset and cryptomap.......
1) will it affect the current VPN?
2) do i need to create a seperate tranformset and cryptomap? or with same tranformset and cryptomap with different number.....if it possible to create multiple cryptomap then i would like that to create.....
View 2 Replies
View Related
Sep 25, 2012
My company purchased a PAK for ASA5505-SEC-PL a while back. I found it unopened and need to know if it can be used, without activating it on an ASA. I opened up a case with the Cisco TAC, provided them the PAK serial number and got the following responses from 2 different individuals:
1.Since the product was covered under warranty and then expired this means that the activation key was used before.
2. This PAK number is expired since (Warranty End Date 21-Feb-2009).
I responded that I am not interested in warranty information but I just want to know if the PAK can be used. Just because the warranty expired, does that REALLY mean the PAK can no longer be used? That doesnt make sense to me. Isn't there a tool on Cisco's website to put in the PAK S/N to see if it is available, has been used, and if so, when?
View 2 Replies
View Related
Jul 3, 2012
i exported config file from asa5505. i changed this file and i imported in my asa5510. can you tell me that config file allright
View 1 Replies
View Related
Dec 14, 2011
I set up a full mesh LAN-to-LAN VPN for a client with 4 sites. Each site has an ASA 5505 running 8.2(5). Site-to-site VoIP traffic runs in the VPN tunnels, as well as traffic to/from a file-server located at the main site. There are two back-up servers, one at the main site and one at a remote site. The main site has 2 bonded T1s and the other three sites have a single T1. How should I go about setting up my QoS?
My top requirement is that VoIP traffic will never be pushed out of the way for data traffic. My secondary consideration is to give more preference to file-server traffic than to web traffic and to make back-up traffic the least important. I'm currently researching to see if the VoIP provider is DSCP marking EF on the VoIP traffic, but I am going to assume they are for now. I know the IP of the file-server and back-up servers.
View 3 Replies
View Related
Nov 10, 2011
I have two ASA 5505 on two different locations(main office and remote office) and I need the remote office to be in the same subnet as the main office since they move computers betweend the offices and they have fixed IP addresses on those computers and they have no right to cahnge to dhcp mode when they move to remore office. Is it possible to create like a bridge over the VPN tunnel so it extens the LAN ?
View 18 Replies
View Related
Nov 29, 2011
Is it possible to use IP "aliases" on an ASA5505 to use as static NAT public IPs to private IPs? For example, I have int e0/0 connected to my ISP using a /30 subnet and I have my private LAN connected to e0/1 with a /24 subnet. At the moment I can use the one usable IP from the /30 to NAT to the private LAN. The ISP is also routing a /28 subnet to the one public IP of the ASA. I would like to use some of the /28 IPs for NAT also. Can it be as easy as just adding the NAT commands? I figure I would have to add that subnet to the ASA somehow, no? In other devices (including the SA520) they use a concept called IP aliases whereby you define what additional IPs the device can use in its NAT config. Does the ASA support aliases? Maybe I have to do something with VLANs?
View 2 Replies
View Related
Jul 25, 2011
I have set up a IPsec L2L VPN between a ASA5510 and a ASA5505 which is working just fine.Every now and then our management station receives the following syslog message: Session disconnected. Session Type: IPsec, Duration: 2h:23m:23s, Bytes xmt: 3283338, Bytes rcv: 8637607, Reason: Phase 2 Error.I have already searched the forum for this message to exclude all the possible reasons for this message:
- the complete crypto maps are the same on both ends (lifetime, psk, pfs etc)
- the ACL's used in the crypto maps are exactly the opposite of each other
View 2 Replies
View Related
Oct 1, 2012
Anyconnect to asa5505 can't connect.
View 1 Replies
View Related
Nov 7, 2011
Can you upgrade an ASA5505 remotely and can you add Anyconnect support (for mobile VPN access) in conjunction with a pre-existing VPN config (so not to interupt the Cisco VPN Client users)?
View 1 Replies
View Related
Jun 15, 2011
it is possible use 1 or 2 Gb memory with ASA 5505 or only 512 Mb ?
View 3 Replies
View Related
Jun 16, 2011
I have 1 network that I'm trying to make secure, and it needs to access 2 seperate networks. I tried using an ASA5505 that I had on the shelf to accomplish this but discovered that I had the basic license and that was prohibiting me from getting my connection to my 3rd network. I scrapped that idea and grabbed an old pix 501 off the shelf to bring my connectivity to my 3rd network online since the 3rd network is only passing ip traffic to a small group of servers on the outside I figure the 501 should be just fine.
So, here's the problem I am running into:My internal network is 10.10.16.0/16, I have a new domain controller with DHCP on it handing out addresses in the 10.10.16.0/24 range.External Network 1 is 192.168.16.0/24. The services I need from that network are primarily in 192.168.0.0 range, however there is a comcast router 75.123.123.123 (Changed of course) that provides high speed internet I need for my www traffic.External Network 2 is 10.1.1.0/16 I have about 4 servers I need to access on this network and that's it. This network has it's own domain and DHCP controller and I've been given a range of ip's to use on this network of 10.1.3.180-10.1.3.189 My switch is just a plane jane 3com switch with minimal management so I am attempting to use my ASA5505 to handle my layer 3 routing.
So here's my issue:ASA5505 (IN:10.10.16.1, OUT: 192.168.16.6): Passes traffic to External Network 1 and to the comcast router, no problem. All my computers on my 10.10.16.0/16 network have access to everything on 192.168.0.0/24 as well as getting full name resolution and www traffic across the comcast router. Can NOT access 10.1.1.0/16 no matter what. From inside the ASA or from on the inside LAN ports. It CAN ping the PIX 501 PIX 501 (IN:10.10.16.3, OUT: 10.1.3.180) Can ping EVERYTHING. Can ping 192.168.0.0/24, can ping 10.10.16.0/16 and can ping 10.1.1.0/16. Set to globally assign the other IP's in my range as addresses for outgoing traffic.Workstations (IN: 10.10.16.XXX DHCP, using 10.10.16.1 as gateway) Can only access everything on External Network 1. ZERO access to External Network 2. ATM I have both INSIDE and OUTSIDE ACL's wide open for both firewalls just to get connectivity going. I will be tightening it up after it is operational.Attached find a log file (Sensetive data removed of course) that contains the sh run and sh ver for both the ASA5505 and the PIX 501.
View 1 Replies
View Related
Dec 26, 2011
I have a new customer that I installed an ASA 5505 to replace a Linksys VPN router. They have a main office with a static IP address, 3 branch offices with static IP addresses and 2 branches that are doing DHCP from the ISP for their router address. I have no problem getting the static VPNs up and running. My problem is with the VPN connections that are doing DHCP. I can go in and determine what IP they are currently using and setup a connection and it works fine. The problem is of course when their IP address from the ISP changes, which seems to happen at least daily. What is the proper way to setup a connection that is using DHCP? Also, can you setup multiple connections this way? Currently the 2 locations have different passwords setup in their routers.
View 1 Replies
View Related
Nov 17, 2011
Completly new to Cisco ASA and need to get this working ASAP.ASA 5505 8.4(1) is the secondary FW and I need for it to allow everything going out and block everything coming in but for the VPN clients. Since a Cisco moron, I used the ASDM and it's wizards to make this work, which might explain my situation.
[code]....
My Cisco VPN Client connects to the ASA and receives 10.10.101.1 IP address, but I get no connectivity to the ASA or any other 192.168.101.x server or service (tried telnet, RDP, ping, etc.)
View 2 Replies
View Related
Sep 20, 2011
For a branch office we have an ASA5505 connected to the ISP with an DHCP provided public IP "locked" to the local MAC This works ok!Now - the ISP may provide up to 5 public IP's (all DHCP assigned).Is it possible to configure 2-5 public interfaces in the ASA?? As IP's are DHCP assigned there must be something (a interface) to request the address.Would this be possible, and if so - what license would be required??NAT routing on the inside should be possible as well.
View 4 Replies
View Related
Mar 14, 2013
I just got an ASA 5505 with Cisco Adaptive Security Appliance Software Version 8.0(4) alredy loaded on it. Should I update/upgrade it to the newest IOS release, or is the 8.0(4) good and stable?
View 3 Replies
View Related
May 3, 2012
I'd like to setup a DMZ network with the ASA5505. Do I need the "Security Plus Bundle"?
View 1 Replies
View Related
Apr 25, 2012
I've been trying to get my WRVS4400N connected to my ASA5505 on the internet through a Cox connection, but it isn't working. I cannot get the ASA to be the DHCP server for the wireless router. I've configured the wireless router as a gateway and pointed the DHCP server to the ASA but no addresses are being passed through to the wireless router. I've included a copy of my config.
ciscoasa# sh run
: Saved
:
ASA Version 8.4(2)
[Code].....
View 3 Replies
View Related
Jun 10, 2013
I currently have my 5505 setup for AnyConnect SSL VPN connections. Is it possible to also configure the 5505 for IPSec VPN connections? So, essentially my ASA will be capable of running SSL and IPSec VPN tunnels, concurrently.
View 2 Replies
View Related
Sep 7, 2011
I have a ASA5505 that I need to allow IPSEC and SSL VPNs through. The ASA is connecting to a BT Business ADSL router, what address should I be using on the ASA outside interface that will allow the ASA to be reachable from the Internet?
View 1 Replies
View Related
Jan 21, 2013
We just purchased a brand new ASA 5505 from EBuyer in the UK. This device only came with the AnyConnect 2.5 software, and actually old firmware too. However, I've discovered that I need a support contract to be able to update the software. We're now stuch with VPN software that doesn't work with Windows 8. This should have been up-to-date out of the box, yet we're being told that we have to pay extra for a support contract just to make it current. This is discusting! Am I missing something, or are other people experiencing the same? Is this a typical Cisco tactic to force people into purchasing support contracts?We paid over £700 for the firewal. I would expect it to have current software bundled with it.
View 2 Replies
View Related
Jul 24, 2012
We are trying to utilize a 5 ip block of addresses provided by our ISP. What we have assigned from them is like this: 10.10.10.46 - 10.10.10.50 is our ip range. 10.10.10.45 is the gateway. Subnet is 255.255.255.248. If we assign 10.10.10.46 to the outside interface how do we accept inbound traffic from the other addresses?
View 6 Replies
View Related
Mar 8, 2011
I would like to configure a cisco ASA5505 IPSEC VPN. I used the wizard and tried to connect to the outside .. does not work .. The network is configured in this manner: - ADSL router with public address and internal address 192.168.2.1 -> firewall interface inside and outside 192.168.2.2 192.168.3.1 (my network is 192.168.3.0). I used a VPN to the pools ranging from 192.168.4.1 to 192.168.4.100.
INTERNET ----- ROUTER ------ ASA5505 -------LAN
What should I change? there could be problems between the router and firewall?
View 6 Replies
View Related
